REPAIR TO DRAIN, FLOORING, ROOF SHEET, PATHWAY, KITCHEN CABINETS AND MISC B/R RELATED WORK WING-III UNDER AGE B/R LEKHANAGAR.

Amount

Dismantling boarding, cup board self/shutter any description fixed in any position with nails/screw etc complete all as specified and directed.

M&L for 25mm thick prelaminated particle board interior grade, prelaminated one side with decorative choice lamination and other side with white lamination including 4mm thk teak wood beading on all edges as in kitchen cabinet, cup board self ,book self, pelment box etc complete all as specified and as directed.

M&L for Block board 12 mm thick , interior grade commertial type fixed with screws to timber frame work all as specified

M&L for Block board 18 to 19mm thick , interior grade commertial type fixed with screws to timber frame work all as specified

M&L for Plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads, Exc 13 Sq cm & n Exc 25 Sq cm.

M&L for Plain fillets, square, rectangular or triangular in section, clean sawn, secured with mills or brads, not Exc 3 Sq cm.

M&L for 0.9 mm thick decorative laminate type 1 of surface finished colour and pattern as approved, fixed with approved adhehive as per manufacturer's instruction

Chamfers, splays, grooves, rebates, rounded angles, rounded nosings, tongued and grooved edges (each tongue and each groove measured) etc., exc 3mm but n. exc 75m girth softwood

M&L for finishing coat with synthetic varnish on new surfaces by sizing, wood filler liquid transperant staining with oil on surfaces of any description over 10 cm in width or girth.

M&L for finishing coat with synthetic varnish on new surfaces by sizing over fillet coat of thin varnishon surfacse of any description, not exc 10cm in width or girth when unconnected with other work or painted in different tint

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised 30mm width of flap(When open)

S&F for 75 mm brass handles, cast type , polished type

S&F 4 levers locks, cupboard, grade I, size 50mm made of brass

S&F magnetic catches brass body and striking plate with aproved quality

S&F Teliscopic runners/slider rails of Drawers closed length 500 to 600mm

S&F aluminium hasp and staple safety fixed in repair type brass with mild steel pin including bolt to hinge plate and fix with screws 100mm size of hasps and staples.

S&F in repairs Stainless steel soft close hydraulic action hinge with capacity to take load of 12 to 20 mm thick board all as per directed and specified by engr-in-charge

S&F 100 mm stainless steel handles, cast type , polished type

S&F in repairs for 100 mm stainless steel handles, cast type , polished type

S&F 75mm butt hinges, medium weight, cold rolled mild steel.

Demolition of brick work in any position built in cement/lime mortar including coping etc., complete all as specified and directed by Engr-in-Charge

M&L for brick work brick with fly ash bricks straight or curved on plan exc 6 m mean radius build in CM 1:4 all as specified.

M&L for Brickwork with sub-class ‘B’ bricks in brick-on-edge walls (less than ½ brick thick), built in CM (1:4) complete all as specified and directed by Engr-in-Charge.

Excavation in trenches not exceeding 1.50 metres wide and not exceeding. 1.50 metre in depth and getting out in any type of soil etc., complete all as specified and directed by Engr-in-Charge.

M&L for providing cement concrete type D-1 (1:4:8) using 40 mm graded crushed stone aggregate as in foundations,filling and massconcrete including necessary form work complete all as specified.

M&L for PCC 1:2:4 type B2, including necessary formwork using 40mm graded crushed stone aggregate, as in surface channels and drains etc including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed by Engr-in-Charge

Taking down cement plaster of any description on brick or stone walls and ceiling including raking out joints, hacking for keys, scubbing down with water etc and complete all specified and as directed.

M&L for 15mm thick cemet plalster in CM 1:4 over concrete/brick surfaces (manholes etc.) finished even and smooth with using extra cement complete all as specified and directed by Engineer-in-Charge.

Removing excavated material exceeding 250m but not exceeding 500m and depositing wheredirected at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25mm thick with excavated soil all as specified.

Excavation/clearance of mud from mansoon drains not exceeding 1.50m wide not exceeding 1.50m in depth and getting out complete all as specified and directed by Engr-in-Charge.

Removing excavated material not exceeding 50m and deposited where directed by Engr-in-Charge at a level not exceeding 1.50m above starting point, complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level)

M&L for 100mm thick PCC 1:4:8 Type D-2(using 40mm graded aggregate) as in sub base over rammed earth complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 Type D-2(using 40mm graded aggregate) as in sub base over rammed earth complete all as specified and as directed.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper mbedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping complete all as specified and directed

M&L for Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper mbedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping complete all as specified and directed

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including necessary eartwork and making drainage opening wherever required complete.

M&L Designer coloured, polished floor paver tiles of size 300 x 300mm x 25mm thick or equivalent size as in machine pressed set, jointed and pointed in neat cement slurry over and including screed be 20mm thick in CM 1.6 including demolition of existing surface complete all as directed by Engineer-in-Charge.

Dismantling floor hearth or wall tiling incl cement mortar bedding (but not backing) removing servicable tiles to store and rubnbish of the permises.

M&L for Rendering 10 mm thick on wall and the like to receive tile in cement mortar (1:4), complete all as specified.

M&L for Screed bed or bedding layer of mortar 15 mm thick average thickness for laying floor finishes in cement mortar (1:4) complete all as specified.

M&L for 25 mm thick, PCC (1:2:4) type B-O using 12.5 mm graded stone aggregates as in flooring as leveling course complete all as specified.

M&L for Non skid ceramic coloured tiles, 7 to 8 mm thick (square or rectangular) area of each tile exe 0.11 Sqm but n.exe 0.18 Sqm, laid in floors set and jointed with neat cement slurry including pointing in white cement with pigment to match the shade of tiles, complete all as specified.

M&L for Non - skid Ceramic coloured tiles7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M&L for light shade vitrified tiles flooring 9-10mm thick (square/rectangular), polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in net slurry and pointed in white or coloured cement to match existing shed complete all as specified and directed.

M&L for Glazed ceramic coloured tiles, of size 300 mm x 200 mmx7mm thick,as in skirting, dado set and jointed with neat cement slurry including pointing in white cement with pigment to match the shade of tiles complete all as specified.

Dismantling wrought iron or mild steel work of any description and in any position complete all as directed by Engr-in-Charge.

Excavation in post holes (or similar holes) each in not exc 0.5 cum getting out and removing surplus soil to a distance in exc 50 mm and making good surface in soft/loose soil complete all as specified and as directed.

S&F for roof trusses (framed), trussed, purlins, rafters, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats Fe-410-W (Gde E-250) Quality -A all as specified and directed.

S&F for steel work as in tabular trusses/supproting pipes etc complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St-240

S&F for plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment

M&L for Preparing new steel surfaces of any description exc 10cm width or grith and applying two coat of synthetic enamel paint over a coat of red oxide complete.

Dismantling AC corrugated or semi corrugated sheets in wall cladding complete all as specified and directed.

S&F for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified

NOTE :- AMOUNT OF SCHEDULE OF CREDIT RS. 14,300.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

Vishal Constructions

M/S K. K. Construction

M/S SAMEER SUBHASH PATANI

A V S Builders

Alpha Construction

SVT ENGINEERS AND CONTRACTOR.

UNITED ENTERPRISES

Bidder Name

Vishal Constructions

A V S Builders

M/S SAMEER SUBHASH PATANI

SVT ENGINEERS AND CONTRACTOR.

M/S K. K. Construction

Alpha Construction

UNITED ENTERPRISES

Abhiraj Enterprises