Renovation of H. No. A-16 to A-21, A-16A to A21A in CCET Campus Block A, Sector 26 Chandigarh. (Total 12 Nos. Houses)

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :DSR 2.10

Pipes, cables etc, not exceeding 80 mm dia DSR 2.10.1.1

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia DSR 2.10.1.2

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : DSR 4.1

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) DSR 4.1.3

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : DSR 6.4

Cement mortar 1:4 (1 cement : 4 coarse sand) DSR 6.4.1

12 mm cement plaster finished with a floating coat of neat cement : DSR 13.7

(1 cement: 4 fine sand) DSR 13.7.2

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:

W.C. pan with ISI marked white solid plastic seat and lid. DSR 17.3.1

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings as DSR 17.28

32 mm dia DSR 17.28.2.1

Providing and fixing soil, waste and vent pipes : DSR 17.35

100 mm dia DSR 17.35.1

Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 DSR 17.35.1.2

75mm diameter : DSR 17.35.2

Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 DSR 17.35.2.2

Providing and fixing plain bend of required degree DSR 17.39

100 mm dia DSR 17.39.1

Sand cast iron S&S as per IS : 3989 DSR 17.39.1.2

75 mm dia DSR 17.39.2

Sand cast iron S&S as per IS - 3989 DSR 17.39.2.2

Providing and fixing heel rest sanitary bend DSR 17.40

100 mm dia DSR 17.40.1

Sand cast iron S&S as per IS - 3989 DSR 17.40.1.2

75mm diameter : DSR 17.40.2

Sand cast iron S&S as per IS - 3989 DSR 17.40.2.2

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. DSR 17.43

100x100x100 mm DSR 17.43.1

Sand cast iron S&S as per IS - 3989 DSR 17.43.1.2

75x75x75 mm DSR 17.43.2

Sand cast iron S&S as per IS - 3989 DSR 17.43.2.2

Providing and fixing single equal plain junction of required degree DSR 17.44

100mm DSR 17.44.1

Sand cast iron S&S as per IS - 3989 DSR 17.44.1.2

75mm DSR 17.44.2

Sand cast iron S&S as per IS - 3989 DSR 17.44.2.2

Providing and fixing collar : DSR 17.57

100 mm DSR 17.57.1

Sand cast iron S&S as per IS - 3989 DSR 17.57.1.2

75 mm DSR 17.57.2

Sand cast iron S&S as per IS - 3989 DSR 17.57.2.2

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : DSR 17.58

100 mm DSR 17.58.1

75 mm DSR 17.58.2

Providing and fixing G.I. pipes complete with G.I. fittings and clamps,i/c cutting and making good the walls etc. : DSR 18.10

15 mm dia. nominal bore : DSR 18.10.1

20 mm dia. nominal bore : DSR 18.10.2

32 mm dia. nominal bore : DSR 18.10.4

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :DSR 18.17

20 mm nominal bore DSR 18.17.1A

Providing and fixing uplasticised PVC connection pipe with brass unions : DSR 18.21

45 cm length : DSR 18.21.2

15mm nominal bore DSR 18.21.2.1

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : DSR 18.46

15 mm nominal bore : DSR 18.46.1

20 mm nominal bore : DSR 18.46.2

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.. DSR 18.48

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 DSR 18.49

15 mm nominal bore. DSR 18.49.1

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. DSR 18.51

15 mm nominal bore. DSR 18.51.1

Providing and fixing C.P. brass Stop Cock ( concealed ) of standard design and of approved quality conforming to IS: 8931 ) DSR 18.52

15 mm nominal bore : DSR 18.52.1

Providing and fixing C.P. brass angle valve for basin mixer and geyser points ... DSR 18.53

15 mm nominal bore. DSR 18.53.1

Providing and fixing CP Brass Extension Nipple ( Size 15 mm x 50 mm ) of approved make and quality as per direction of EIC DSR 18.53A

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : DSR 17.60

100 mm inlet and 75 mm outlet DSR 17.60.2

Sand cast iron S&S as per IS - 3989 DSR 17.60.2.1

Providing and fixing PTMT Ball Cock of approved quality, color and make complete with Epoxy Coated aluminium rod with LP/HPHD Plastic Ball

20 mm Nominal Bore DSR 18.62.2

Cutting holes up to 30x30 cm in walls including making good the same: DSR 18.76

With common burnt clay F.P.S. (non modular) bricks : DSR 18.76.1

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. : DSR 18.77

Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc.: DSR 18.78

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: DSR 19.4.

100x100 mm size P type DSR 19.4.1

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR 19.4.1.1

Providing and fixing of C.P. brass Jet with brass nossel steel flange & PVC flexible pipe complete in all respect DSR 17.16A

Providing and fixing of C.P. Steel Grating Heavy (With hole without hole) 100 mm dia, of approved make

Providing and fixing of CP Brass/SS Towel Ring with screws etc. to the satsifaction of EIC of approved make Jal Model No. 36524 Warna or equialent Model of CERA /Kerovit/ ESSCO

Providing and fixing of CP Brass/SS Towel Rail 600mm of with screws etc. to the satsifaction of EIC of approved make Jal Model No. 36520 Warna or equialent Model of CERA /Kerovit/ ESSCO

Providing and fixing of CP Brass/SS/ABS overhead shower with swiveling Joint , 125mm dia (min) with C.P Brass/ S.S Shower Arm and flange to the satsifaction of EIC of approved make ESSCO Model No. 536A & 542A or equialent Model of CERA /Kerovit/ Jal

Providing and fixing of CP Brass/SS/ABS Soap Tray made of Plastic including glass bowl of approved make Jal Model No. 36540 or equialent Model of CERA /Kerovit/ ESSCO

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : Flat back wash basin of size 550x400 mm DSR 17.25.2

Providing and fixing of CP Pillar Cock of approved make

Providing and fixing of CP Waste for Basin of approved make

Providing and fixing of CP sink Waste for S.S Sink of approved make

Providing and fixing of G.I. elbow 80 mm x 32 mm of approved make

Providing and fixing of C.P. brass Cup ( Heavy Duty ) of approved make

Providing and fixing HCI Cover with frame for GT & IC of approved make

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required (27" X 20" X 8") Make JAYNA or as per approved make list

Prov. & fixing of looking mirror of size 450x600mm made with 5mm thick (minimum) superior quality glass including cost of hard board, PVC beading and C.P. Screw etc. to satisfaction of EIC of approved make

Please Enable Macros to View BoQ information