Extension to old CRECHE building near open air theater at NCL

Amount

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including ramming of bottom, getting out and disposal of excavated earth upto 50 m and lift upto 1.5m, as directed by Engineer-in- Charge:All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including required re-filling of trences ,dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.,All kinds of soil.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Providing and laying in position excluding cement concrete of level: specified grade the cost of centering and shuttering - All work up to plinth,1:2:4 (1 cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position excluding cement concrete of level: specified grade the cost of centering and shuttering - All work up to plinth-1:3:6 (1 Cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls Under 20 cm wide

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with clay flyash F.P.S. (non modular) brick of class designation7.5 in superstructure above plinth level up to floor five level in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, edges moulding and polishing of all edges to give high gloss finish as per instruction of Engineer-in charge etc. complete at all levels. Granite stone slab of all colour and texture except black, Cherry/Ruby red ...Area of slab over 0.50 sqm

Extra for fixing granite stone, over and above corresponding basic item only for facia,door/window/ventilator frames and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including making holes for pillar taps etc. and moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing 1st quality ceramic glazed wall tiles of size 300x600mm conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3(1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate of Classic Rh95 of make Armstrong false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of make Armstrong of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main 'T' runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross "T" of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main'T' at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross 'T' of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main 'T' runners to be suspended from ceiling using al. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, hanging with good quality MS wire upto 2mm , spaced at 1200 mm centre to centre along main 'T'. Bottom exposed with 24 mm of all T-sections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection >85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying Vitrified tiles in floor in diferent sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily including skirting on wall upto 150mm height. Double charge vitrified tile polished finish of size -Size of Tile 600 x 600 mm

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500- 600mm)

12 mm cement plaster of mix: 1:4(1 cement: 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix: 1:4(1 cement: 4 fine sand)

20 mm cement plaster of mix: 1:4(1 cement: 4 coarse sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement: 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement: 3 coarse sand) finished rough with sponge.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour: New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 Itr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

French spirit polishing :Two or more coats on new works including a coat of wood filler

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint (Luster) of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.Two coats

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

6 mm cement plaster of mix :1.3 (1 cement: 3 fine sand)

Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface including disposal of mulba/ rubbish to the nearest municipal dumping ground, all complete as per direction of Engineer-in-Charge. For door/ window/ clerestory window

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane , including painting of top surface of membrane by aluminum paint : 3 mm thick

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Supplying and stacking at site. 63 mm to 45 mm size stone aggregate

Supplying and stacking at site. Stone screening 11.2 mm nominal size (Type B)

Supplying and stacking at site. Moorum

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with vibratory roller in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density .

Supplying and fixing at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in- charge. Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60 mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) of make Jaquar/kohler/Durovit with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type) of make Jaquar/kohler/Durovit with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink of make Jaquar/kohler/Durovit , stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board -610x510 mm bowl depth 200 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe-32 mm dia

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall 20 mm dia nominal bore

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, including making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :-15 mm dia nominal bore

Providing and fixing brass stop cock of approved quality :20 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :20 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length-15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass long nose bib cock of make-Jaquar or equivalent .-15 mm nominal bore

Providing and fixing C.P. brass angle valve of make Jaquar/kohler/Durovit for basin mixer and geyser points : 15 mm nominal bore

Providing and fixing 8 mm dia C.P. I S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of of make Jaquar/kohler/Durovit .

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :100 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 100 mm diameter S.W. pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:150 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 Rectangular shape 600x450 mm internal dimensions

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately): For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket, sliding arrangement,locking arrangement for sliding window , Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of upto 4.0 mm thickness

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing Brass 100 mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-charge ,Powder coated minimum thickness 50 micron aluminium

Providing and fixing white vitreous china under counter wash basin of make Jaquar/kohler/Durovit of size not less than 560x450 mm including making all connections including the cost of waist couplingec complete.

Extra rate for supply of ready mixed or site batched design mix concret as per same grade as mentoined in original item of concretes ,complet item execute as per as per direction of the engineer-in-charge.

Providing and fixing Health faucet ABS body with I metre SS braided connection pipe with necessary fitting etc.make-Cera or equivalent

Providing and fixing 2way Bib cock with necessary fitting etc.make Jaquar/kohler/Durovit

Providing and fixing 15mm Pillar cock long neck with areator with necessary fitting etc.make-Jaquar or equivalent

Providing and Fixing superior glass (of approved quality) looking mirror of 5mm thick with frame made out by aluminium shutter profile or aluminium frame with good quality gasket for glass,back side backing PP foam sheet fixing arrangement,complete item excute as directed by Engineer-in-charge. Make- Modi /sant gobin or eqivalent

Providing and Fixing 100 mm PVC Floor nhani trap Make Finolex or eqivalent for drainage work including necessary cuttting,jointing with adhesive and etc.

Providing and laying 110mm PVC pipe Make Finolex or eqivalent for drainage work including necessary cuttting,jointing with adhesive and etc.

Providing and laying 75mm PVC pipe Make Finolex or eqivalent for drainage work including necessary cuttting,jointing with adhesive and etc.

Providing and fixing100 mm PVC pipe accessories door Bend /Plain Bend/Elbow/Tee Make Finolex or eqivalent for drainage work including necessary cuttting,jointing with adhesive and etc.

Providing and fixing 75 mm PVC BEND /elbow Make Finolex or eqivalent for drainage work including necessary cuttting,jointing with adhesive and etc.

Constructing brick masonry manhole inside size 90x80cm and 45cm deep in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C Precast manhole cover of size 900 x 600 mm medium duty , foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :With fly ash bricks of class designation 7.5

Providing and fixing decorative waterproof 7 to 8 mm PVC ceiling, size of PVC board 10 feet x 12 inch in any colour and designs including metal frame ie. C-Channel,wall angle ( galvanized steel with zinc coating ),suspension system shall be professionally execute with GI wire and self tapping srews. The entire grid system shall be designed to bear a distributed load of false ceiling system shall include providing necessary cut-outs for all sized light fixture,AC Diffuser,dampers and liner grill,smoke detectors ,speakersetc. rate including provision of drop for creating layers or design etc.complete item as directed by Engineer-in-charge.(Actual area should be measure for payment)

Providing and fixing 18mm thick MR Grade plywood approved brand and manufacture in frame work of cup-board,table tops,table side,partition,shelves etc.with adhesive and nails, etc.complete as per the direction of Engineer-in-charge.Ply-wood use make only:- Green ecotech,Century,National ,Mountwall,Gargan or Tower etc.

Providing and fixing 18mm thick MR Grade plywood approved brand and manufacture in the cup-board shutters,drawers and key board Including 2nd class teak wood lipping of 18x5mm size to the exposed edges with necessary screws, adhesive, nails ,nickle plated bright finished w-hinges , decorative brass handles, mangnatic door catcher, brass cup-board lock,Telescopic channel for drawers,Chain for shutter ,etc.complete as per the direction of Engineer-in-charge.Ply-wood use make only:-Green ecotech,Century,National ,Mountwall,Gargan or Tower etc.

Providing and fixing 1mm thick decorative laminate lamination of PEARL GLOSS/SUEDE finish to the cup-board / ward robe shutters, with necessary screws,adsive,nails etc complete as per directed by the Engineer-in-charge.GREENLAM or HERITAGE make only.

Providing and fixing 0.6 to 0.7 mm thick laminate finish to internal surface of cup-board , ward robe , drawers ,shutters, with necessary ,adsive,nails etc complete as per directed by the Engineer-in-charge.

Providing and fixing Polycarbonet 3mm thick (solid) sheet in any colour for roofing in any shape including fixing arrangement ie. self threaded screw with wishers,epoxy sealent etc. complete item as directed by engineer in charge..(Actual area should be measure for payment)

Providing and fixing 30mm smartkool roof PUF insulated tounge and grove panels,sheet 0.5/0.5mm thick make JSW make AZ70/PPGL AMNS make 80GSM, Puf density 40 (+/-2kg) kg/m3 insulated roofing sheets ,precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) . Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required,Including the end cap to the PUF panel/sheet.( Make Sametkool/Rinac/Jsw/alfaa)

( Light / Exhaust point in PVC casing capping/pipe) Wiring for light point / Ex.pt. with PVC insulated, copper conductor wires of size 2 x 1.5 Sq.mm ( 22 / 0.3 ), 1100 V grade, fire resistant ( FRLS ) (Red colour for phase & Black colour for Neutral ) and 1.00 Sq.mm (14 / 0.3 ), 1100 V grade, fire resistant green colour wire for earth continuity conductor Finolex / RPG /Polycab :-Make in 30 mm PVC casing capping ,ivory colour,Modi:-Make or in 20 mm Diam.16 SWG thick PVC ,grey colour pipe,Asian/Diamond :-Make ( with required. essential PVC acc.such as bend / Jn.box etc.) & white colour ceiling rose . The rate includes supplying, fixing & connecting white colour Legrand ( Myrius) :-Make a) 6 A.S.P.switch ( with out indicator) b) Moulded 1-module front plate suitable for 6 A.S.P.switch. c) Surface type white powder coated metal box suitable for 1 module front plate. ( Rate for this Item should include cost of material & labour charges req.for complete execution of Item)

( Fan point in PVC casing capping/pipe) Wiring for light point / Ex.pt. with PVC insulated, copper conductor wires of size 2 x 1.5 Sq.mm ( 22 / 0.3 ), 1100 V grade, fire resistant ( FRLS ) (Red colour for phase & Black colour for Neutral ) and 1.00 Sq.mm (14 / 0.3 ), 1100 V grade, fire resistant green colour wire for earth continuity conductor Finolex / RPG /Polycab :-Make in 30 mm PVC casing capping ,ivory colour,Modi:-Make or in 20 mm Diam. 16 SWG thick PVC pipe,grey colour,Asian/Diamond :-Make ( with required. essential PVC acc.such as bend / Jn.box etc.) & ceiling rose. The rate includes supplying, fixing & connecting white colour Legrand ( Myrius) :-Make a) 6 A.S.P.switch ( with out indicator) b)100W,Step type,humfree,2-module type fan regulator,Code no:- 6730 29 c) Moulded 3-module front plate suitable for 6 A.S.P.switch. & fan Reg. d) Surface type white powder coated metal box suitable for 3 module front plate. ( Rate for this Item should include cost of material & labour charges req.for complete execution of Item)

(Ckt.wiring for lighting switchboards in PVC casing capping/PVC pipe) Wiring for circuit wiring with PVC insulated copper conductor wires of Size 4x2.5 Sq.mm.,1100V grade,FRLS (R-Y-B for phase & black colour for neutral) and 1 x 2.5 Sq.mm,1100v grade green colour wire for earth continuity conductor Finolex/ RPG/Polycab:-Make in 30 mm .PVC casing capping ,ivory colour ,Modi:-Make or in 20 mm Diam. PVC ,grey colour conduit ,Asian/Diamond :-Make ( with required. essential PVC acc.such as bend / Jn.box etc.) ( Rate for this Item should include cost of material & labour charges req.for complete execution of Item)

(Ckt.wiring for lighting switchboards and power baords in PVC casing capping/PVC pipe) Wiring for circuit wiring with PVC insulated copper conductor wires of Size 2x2.5 Sq.mm.,1100V grade,FRLS (R-Y-B for phase & black colour for neutral) and 1 x 2.5 Sq.mm,1100v grade green colour wire for earth continuity conductor Finolex/ RPG/Polycab:-Make in 30 mm .PVC casing capping ,ivory colour ,Modi:-Make or in 20 mm Diam.,16 SWG thick PVC ,grey colour pipe,Asian/Diamond :-Make ( with required. essential PVC acc.such as bend / Jn.box etc.) ( Rate for this Item should include cost of material & labour charges req.for complete execution of Item)

(Ckt.wiring for power point in PVC casing capping/PVC pipe) Wiring for circuit wiring with PVC insulated copper conductor wires of Size 4x4 Sq.mm.,1100V grade,FRLS (R-Y-B for phase & black colour for neutral) and 1 x 4 Sq.mm,1100v grade green colour wire for earth continuity conductor Finolex/ RPG/Polycab:-Make in 30 mm .PVC casing capping ,ivory colour ,Modi:-Make or in 20 mm Diam.and 16 SWG thick PVC ,grey colour pipe,Asian/Diamond :-Make ( with required. essential PVC acc.such as bend / Jn.box etc.) ( Rate for this Item should include cost of material & labour charges req.for complete execution of Item)

(Ckt.wiring for power point in PVC casing capping/PVC pipe)Wiring for circuit wiring with PVC insulated copper conductor wires of Size 2x4 Sq.mm.,1100V grade,FRLS (R-Y-B for phase & black colour for neutral) and 1 x 4 Sq.mm,1100v grade green colour wire for earth continuity conductor Finolex/ RPG/Polycab:-Make in 30 mm .PVC casing capping ,ivory colour ,Modi:-Make or in 20 mm Diam.and 16 SWG thick PVC ,grey colour pipe,Asian/Diamond :-Make ( with required. essential PVC acc.such as bend / Jn.box etc.) ( Rate for this Item should include cost of material & labour charges req.for complete execution of Item)

(Main I/C Cable from MSEDCL meter to power DB SITC of PVC insulated and PVC Sheathed/XLPE power cable of size 70 or 50 Sq.mm 3.5 core, 1.1KV grade Al Ar.Cable. Laying direct in ground including excavation, sand cushioning, protective cover and refilling the trenche etc.. Make: Polycab/R.R/Finolex ( Rate for this Item should include cost of material & labour charges req.for complete execution of Item).

Cable Temination: Supply and making end termination with brass compression gland and aluminium lugs for 70 or 50 Sq.mm 3.5 core, 1.1KV grade Al Ar.Cable

( SITC of BLDC ceiling fan) Supply, Installation, Testing and Commissioning of 1200 mm sweep,BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC)Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019),THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts,washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply,earthing etc complete as required.Make: Havells/Atomburg/Lukar.

( Supply & fixing of Ex.fan ) Supplying,fixing & connecting light duty Exhaust fan with following specifications:- Light duty , Single Phase, 230 V, 50 Hz, Size:- 200 to 300 mm (12"), 1400 RPM Make:- Hawells ,Model:-Ventil Air DSP or Equivalent Model of :-Crompton / Alstom / Havells/Atomburg. The rate includes fixing of Exhaust Fan in the window either by using 1" thick waterproof Wooden Pank or by fabricating suitable size of M.S. angle / flat frame.

( Tubelight fitting to be fixed on wall/Ceiling) Supplying,fixing & connecting on wall with string/Elite 24 W,4Feet LED tubelight fitting, with following specifications:- LUKER :-Make,6000K,Model:- LT5M24 WH, ,(or equivalent model of Havells/Philips/Jaquar)

( LEDt fitting to be fixed on false ceiling with fixing Accessories ) Supplying,fixing on ceiling with string/Elite suspesion kit & connecting 15w, Square or Round LED fitting, with following specifications:- LUKER :- Make ELAGANT NEO Slim Pane ,6000K,Model:- LNPS15/LNPR15,(or equivalent model of Hawell/Philips/Jaquar)

(Switch board for power point ) Supplying,fixing,connecting fully prewired Logic modular system type Legrand( Myrius) :- Make switch board with following specifications. a)16 module white Plate with frame:---01 no. Code No.673216 b) White powder coated metal mounting box suitable ,for 16 module front plate. :---01 no. Code Code No.689021, c) 16 A. S.P.switch ( w/o indicator) :-04 nos. Code No.673008 d) 16 Amp/6Amp 3Module, universal type socket :- 04 nos. Code No.673083

(Switch board for power point ) Supplying,fixing,connecting fully prewired Logic modular system type Legrand( Myrius) :- Make switch board with following specifications. a) 8 module white Plate with frame:---01 no. Code No.6732 68 b) White powder coated metal mounting box suitable ,for 16 module front plate. :---01 no. Code Code No.689021, c) 16 A. S.P.switch ( w/o indicator) :-04 nos. Code No.673008 d) 16 Amp/6Amp 3Module, universal type socket :- 04 nos. Code No.6733 08

(SITC OF DP MCB in Enclosure for str.light,gyser and ACs) Supplying,fixing & connecting Legrand :-Make,25A DP MCB,Cat.no.408634 inS.S. Enclosure

(SITC OF PDB 1 no. for old bldg. & 1 no. for newe bldg.) Supplying,fixing & connecting the 12 way 1 Phase DPX3, MCB SPN DB,VTPN of Legrand:- Make with Model: Ekinoxe.Cat.no.507612(IP43-IK 09,with metal door) The DB Contains :- a)Main I/P -63A DP RCBO,with 30mA sensitivity Cat.no.411328-1No c)O/P-25A SP MCB,Cat.no.4085 94-5 Nos. d)O/P-32A SP MCB,Cat.no.4085 95-5 Nos.

(Street Light Fitting ) Supplying, installing, testing & commisioning of LED Street light on streetlight pole or on wall with mounted bracket LED type street light fitting 48W-60W,Make:-Lukar:- Make .CODE:LST048 WH Sensor(or equivalent model of Havells/Philips/Jaquar) The LED Light fiting should have minimum 1 years replacement warranty Rate is inclusive of:- 1)Testing fitting by actual giving the supply. 2)Labour charges required for fixing fitting on the New pole / Existing pole/on wall with bracket and accessories.

SITC of BORE type Maintenance free GI Pipe -in-pipe type Earthing ( 1 nos. for Street light poles & 1 for Crenche building) 1)Supply of 76 MM dia 3 MTR Long G.I. Maintenance Free Earthing Electrode, Pipe-IN-Pipe, Outer Pipe 76 MM OD & Inner Pipe 42 MM, cavity between Pipes filled with High conductive, non-corrosive crystalline mixtures compound, permanently sealed at both the ends especially designed for Electrical grounding, along with 2 Bag of 25 kg. SRIP Chemical Compound. Model-PPS-76-3 2) Supply of GI Strip - 50 X 6 MM --4 mtr 3)Heavy Duty Polyplastic Earth Pit Chamber with Cover. 4)Rate includes making bore of suitable diameter and 3mtr deep in the ground using boring m/c and refilling it with maintenance free chemical compound.(SRIP Chemical Compound. Model-PPS-76-3) etc. complete for the complete execution of Item. ( Contractor should measure Earth resistance and issue certificate in the name of end user)

( SITC of GI Earthing Strip ) Supplying ,laying & fixing earth continuity conductor of 25mm x 5 mm G.I.earthing on wall /undeground etc as per site condition including clamp,spacers,welding,providing protective painting on welded portion as required & directed by site engineer(Rate includes digging 0.5 mtr below ground for laying strip.Also joint is to be done with nut-bolts ,spring washer etc complete.),

( SITC of MCCB with Enclosure ) SITC of 125A 10KA, 4 Pole MCCB With enclosure for Incoming supply. Make: Legrand or L&T, 125Amp, 4 Plole 10KA MCCB, cat No. 0270 08, Ekinox metal enclosure Cat No. 507915

KASHYAP CONSTRUCTION (BID ID -931250)