REPAIR/ REPLACEMENT OF ELECTRICAL FITTINGS AND FIXTURES IN LIFT SHAFT, MACHINE ROOM, LIFT CABIN AT VARIOUS LOCATIONS EXCLUDING BAIRD PLACE AND KABUL LINE UNDER GE UTILITY PLANT AND MACHINERY DELHI CANTT-10

Amount

Section-1

Taking down carefully existing surface/ concealed unserviceable aluminum/ copper point wiring (light, fan, socket, power or sunken box) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets, bracket holder, boards light fittings, etc. and making good to disturbed surfaces of walls, floors, ceilings, etc. where required and finished the existing surfaces after complete of new point wiring as specified here-in-after complete all as specified and as directed by Engr-in-Charge.

Taking down unserviceable sub main wiring of any type and any size including wooden batten, PVC conduit or casing caping complete all as specified and as directed by Engr-in-Charge.

Taking down unserviceable main switch/ DBs of any size/ capacity including MCB any type & capacity for reuse carefully disconnecting and making good to disturbed surfaces complete all as specified and directed by Engr-in-Charge.

Taking down unserviceable MCB (SP, SPN, TPN any capacity), Isolator/ MCCB of any rating, size/ capacity complete all as specified and directed by Engr-in-Charge.

M & L for Point wiring complete with 1.5 Sqmm single core unsheathed PVC insulated 1100 V, FRLS grade with multistranded copper conductor ISI marked drawn through in existing concealed / surface PVC/Steel conduit and accessories and existging MS pressed steel terminal box and replace laminated sheet 3mm thick for mounting of switches, socket regulator etc including 1.5 Sqmm PVC insulated FRLS unsheathed cable multistranded copper conductor and connecting to earth dolly for for one light / Fan / exhaust fan controlled by one, one way switch complete all as specified & directed by Engr-in-Charge. (Make of cable:- FINOLEX / RR KABEL/ HAVELL'S/ POLYCAB .) {Notes:- (i) Switches and sockets to be measured and paid for separately under relevent items.}

-ditto- all as per item No. 6.00 above but for one bell/buzzer point controlled by one, one way switch on the independent board complete all as specified and directed by Engr-in-Charge.

-ditto- all as per item No. 6.00 above but for one 3 pin 5/6 Ampere socket outlet point controlled by one, one way switch on the independent board complete all as specified and directed by Engr-in-Charge.

-ditto- all as per item No. 6.00 above but for one 3 pin 5/6 Ampere socket outlet point controlled by one, one way switch on the same board complete all as specified and directed by Engr-in-Charge.

-ditto- all as per item No. 6.00 above but with 4 Sqmm cable for 15 Amp switch socket out let point on independent board including 4 Sqmm PVC insulated unsheathed cable multistranded with copper conductor earthing continuity conductor all as directed and specified by Engr-in-charge. Notes:- (i) Switches and sockets to be measured and paid for separately under relevent items.

M & L for point wiring (concealed complete) using 1.50 sqmm size FRLS, PVC insulated, unsheathed 1100 volts grade single core multi-stranded copper conductor cable in proper colour coding drawn into and including non metallic rigid PVC conduit medium grade (not less than 20 mm dia) for wall and 25mm PVC medium grading grade casing and caping in the ceiling wherever required with and including its all necessary fittings and accessories fixed concealed, sunk cast iron or 1.2 mm thick pressed steel terminal box for mounting fittings and covered with 3 mm thick white bakelite / laminated hard glossy surface sheet top cover fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 1.50 sqmm size FRLS stranded copper conductor cable as in earth wire and connecting all metal parts to common earth dolly for one light / Fan / exhaust fan / Bell point controlled by one, one way switch complete all as specified & directed by Engr-in-Charge. (Make of cable:- FINOLEX / RR KABEL/ HAVELL'S/ POLYCAB .) (Make of PVC conduit & Casing caping:- FINOLEX / ANCHOR/ KALINGA/ SUPREME/ POLYCAB.) {Notes:- (i) Switches and sockets to be measured and paid for separately under relevent items.}

-ditto- all as per item No. 11.00 above but for one bell/buzzer point controlled by one, one way switch on the independent board complete all as specified and directed by Engr-in-Charge.

-ditto- all as per item No. 11.00 above but for one 3 pin 5/6 Ampere socket outlet point controlled by one, one way switch on the independent board complete all as specified and directed by Engr-in-Charge.

-ditto- all as per item No. 11.00 above but for one 3 pin 5/6 Ampere socket outlet point controlled by one, one way switch on the same board complete all as specified and directed by Engr-in-Charge.

-ditto- all as per item No. 11.00 above but for one light point controlled by one, two way switch on the same board complete all as specified and directed by Engr-in-Charge.

-ditto- all as per item No. 11.00 above but with 4 Sqmm cable for 15 Amp switch socket combination out let point on independent board including 4 Sqmm PVC insulated unsheathed cable multistranded with copper conductor earthing continuity conductor all as directed and specified by Engr-in-charge. Notes:- (i) Switches and sockets to be measured and paid for separately under relevent items.

Supply and fixing of switch piano, flush type, ivory finish 5/6 Ampere single pole, one way with marking as light complete, all as specified and directed by Engr-in-Charge. Make : Anchor / Legrand/ Schneider/ C & S/ Cona / Havells

Supply and fixing of bell push, ivory finish 5/6 Ampere single pole, one way complete, all as specified and directed by Engr-in-Charge. Make : Anchor / Legrand/ Schneider/ C & S/ Cona / Havells

Supply and fixing of switch socket out let combination 2 in 1, 3 Pin suitable for 5/6 Ampere for independant board flush type complete all as specified and as directed by Engr-in-Charge. Make : Anchor / Legrand/ Schneider/ C & S/ Cona / Havells

Supply and fixing of socket out let 2 in 1, 3 Pin suitable for 5/6 Ampere in same board flush type complete all as specified and as directed by Engr-in-Charge. Make : Anchor / Legrand/ Schneider/ C & S/ Cona / Havells

Supply and fixing of socket out let multipurpose 2 in 1, 3 Pin suitable for 5/6 Ampere and 3 Pin suitable 15/16 Ampere flush type complete all as specified and as directed by Engr-in-Charge. Make : Anchor / Legrand/ Schneider/ C & S/ Cona / Havells

Supply and fixing of switch piano, flush type, ivory finish 15/16 Ampere single pole, one way with marking as light complete, all as specified and directed by Engr-in-Charge. Make : Anchor / Legrand/ Schneider/ C & S/ Cona / Havells

Supply and fix Switch socket combination flush type multi purpose 3 pin 16 Amps and one 3 pin 6 Amps controlled by one switch with fuse & neon indicator ISI mark Make : Anchor / Legrand/ Schneider/ C & S/ Cona / Havells

Supply and fixing of stepped type 5 steps 100 watts electronic fan regulator flush type on the existing phenolic laminated sheets etc as required all as specified and as directed by Engr-in-Charge. (Make : Anchor / Havells / Usha / Crompton / Bajaj)

-ditto- all as per item No. 17.00 above but for one 5/6 Ampere two way switch complete all as specified and directed by Engr-in-Charge.

Supply and fixing of modular switch one module, 5/6 Amp, one way, 230 volts AC complete all as specified and directed by Engineer-in-Charge. (Make : Anchor / Cone / Crabtree / Legrand )

Supply and fixing of modular type bell push, 6 Amps, 1 module complete all as specified and as directed by Engr-in-Charge. (Make :- Anchor / Cona / Wipro / Bajaj/ Havells)

Supply and fixing of modular socket outlet (two module) 5/6 amps, 2 in 1, 2 & 3 pin combined, 230 volts AC complete all as specified and as directed by Engr-in-Charge. (Make : Anchor / Cone / Crabtree / Legrand)

Supply and fixing of modular socket out let (two module), 2 in 1, 3 Pin suitable for 5/6 Amp and 3 Pin suitable 15/16 Amp combined, 230 volts AC complete all as specified and as directed by Engr-in-Charge. (Make : Anchor / Cone / Crabtree / Legrand)

Supply and fixing of modular type electronic fan regulator with 2 module as required all as specified and as directed by Engr-in-Charge. (Make : Anchor / Havells / Usha / Crompton / Bajaj)

Supply and fixing ceiling rose surface type Bakelite, three terminal 65x50mm, 3 terminals complete all as specified and directed by Engr-in-Charge. (Make : Anchor/ Cona/ Havells.)

Supply and fixing of electric ding dong bell, 230 volt AC, single pole, complete all as specified and as directed by Engineer-in-Charge. (Make :- Anchor / Cona / Wipro / Bajaj/Havells)

Supply and fixing of lamp holder pendant/angle type, PVC/polycarbonate type, insulated body with back plate of batten fitting complete all as specified and as directed by Engr-in-Charge. (Make : Anchor / Ess Ess Kay / Plaza / Havells)

Supply and fixing of modular White cover plate with frame, 1 module complete all as specified and as directed by Engr-in-Charge. (Make : Anchor / Cone / Crabtree / Legrand)

Supply and fix modular white cover plate with frame but 2 module complete all as specified and as directed by Engr-in-Charge. (Make : Anchor / Cone / Crabtree / Legrand)

Supply and fix modular white cover plate with frame but 3 module complete all as specified and as directed by Engr-in-Charge. (Make : Anchor / Cone / Crabtree / Legrand)

Supply and fix modular white cover plate with frame but 4 module complete all as specified and as directed by Engr-in-Charge. (Make : Anchor / Cone / Crabtree / Legrand)

Supply and fix modular white cover plate with frame but 6 module complete all as specified and as directed by Engr-in-Charge. (Make : Anchor / Cone / Crabtree / Legrand)

Supply and fixing in replacement modular metal flush box with 1.6 mm thick 1/2 module flishing mounting in the wall for fitting cover plate with frame on swith/socket complete all as specified . (Make : Anchor / Cone / Crabtree / Legrand)

Supply and fixing in replacement modular metal flush box with 1.6 mm thick 3 module flishing mounting in the wall for fitting cover plate with frame on swith/socket complete all as specified. (Make : Anchor / Cone / Crabtree / Legrand)

Supply and fixing in replacement modular metal flush box with 1.6 mm thick 4 module flishing mounting in the wall for fitting cover plate with frame on swith/socket complete all as specified. (Make : Anchor / Cone / Crabtree / Legrand)

Supply and fixing in replacement modular metal flush box with 1.6 mm thick 6 module flishing mounting in the wall for fitting cover plate with frame on swith/socket complete all as specified. (Make : Anchor / Cone / Crabtree / Legrand)

Supply & fixing in replacement of existing unserviceable T/L fitting 36/40 W on existing wall with New LED tube light fitting 18/20 watts with tube rod and necessary braket,clamps ,incl. bolts, nuts & washers for fixing arrangement etc complete all as specifed and directed by Engineer-in-charge. Make-Havells Cat No LUMILINEPLUSBS18WLED865SPCSS or eqvt make of PHILIPS/BAJAJ/CG

Supply & fixing in replacement of existing unserviceable T/L fitting 20 W/Lamp holder on existing wall with LED light fitting 10 watts with LED tube rod, ready to use pack with necessary braket,clamps ,incl. bolts, nuts & washers for fixing arrangement etc complete all as specifed and directed by Engineer-in-charge. Make-Havells Cat No LUMILINEPLUSBS10WLED865SPCSS or eqvt make of PHILIPS/BAJAJ/CG

Supply & fixing in replacement of surface mounting round downlight LED 12/13.5 watt luminarie complete fitting with all fixing arrangement all as specified and directed by Engr-in-Charge. Make- Havells Cat No LHEXCFP7IN5W013 or eqvt make of PHILIPS/BAJAJ/CG

Supply & fixing in replacement of surface mounting Bulkhead LED fitting13.5 watt luminarie complete fitting with all fixing arrangement all as specified and directed by Engr-in-Charge. Make-Havells Cat No LHEXCGP7IN5W013 or eqvt make of PHILIPS/BAJAJ/CG

Supply & fixing in replacement of 20 Watt LED security light fitting with pressure dia cast housing, prismatic, polycarbonate diffuser and IP65 protection with 0.6 mtr long 20/25 mm (as per manufacturer standard) dia GI Pipe in 45 degree bend shape and necessary clamping devices required at site complete all as specified and directed by Engr-in-Charge. Make-Havells Cat No ENDURAPEARLSL20WLED757SASYTOPCMP or eqvt make of PHILIPS/BAJAJ/CG

Supply & fixing in replacement of recess mounting 2x2 LED luminarie, 34 W deep drawn CRCA housing with high power LED premium white powder coated frame blends seamlessly with ceiling layout, suitable for 600x600 mm modular ceiling grid and also can be suspended with provided kit, complete fitting with all fixing arrangement all as specified and directed by Engr-in-Charge. Make-Havells Cat No PLUTONEO2X2PLR34WLED840S or eqvt make of PHILIPS/BAJAJ/CG

Material and labour for sub main wiring with two runs of single core 1.5 Sqmm (nominal area) PVC insulated copper conductor FRLS (conforming to IS-694), stranded, unsheathed 1100 volts grade in PVC Conduit (heavy grade) of 20mm dia or more dia with all fittings and accessories surface type including one run 1.5 Sqmm single core unsheathed stranded copper conductor cable FRLS (conforming to IS-694) as earth wire complete all as specified and as directed by Engr-in-Charge.

Material and labour for sub main wiring with two runs of single core 2.5 Sqmm (nominal area) PVC insulated copper conductor FRLS (conforming to IS-694), stranded, unsheathed 1100 volts grade in PVC Conduit (heavy grade) of 20mm dia or more dia with all fittings and accessories surface type including one run 2.5 Sqmm single core unsheathed stranded copper conductor cable FRLS (conforming to IS-694) as earth wire complete all as specified and as directed by Engr-in-Charge.

Material and labour for sub main wiring with two runs of single core 4.0 Sqmm (nominal area) PVC insulated copper conductor FRLS (conforming to IS-694), stranded, unsheathed 1100 volts grade in PVC Conduit (heavy grade) of 20mm dia or more dia with all fittings and accessories surface type including one run 4.0 Sqmm single core unsheathed stranded copper conductor cable FRLS (conforming to IS-694) as earth wire complete all as specified and as directed by Engr-in-Charge.

Material and labour for sub main wiring with two runs of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLS (conforming to IS-694), stranded, unsheathed 1100 volts grade in PVC Conduit (heavy grade) of 20mm dia or more dia with all fittings and accessories surface type including one run 6.0 Sqmm single core unsheathed stranded copper conductor cable FRLS (conforming to IS-694) as earth wire complete all as specified and as directed by Engr-in-Charge. Notes for item Nos 49.00 to 52.00 (Make of cable : FINOLEX / RR KABEL/ HAVELL'S/ POLYCAB/ L & T/ ANCHOR.) (Make of PVC conduit:- FINOLEX / PLAZA/ KALINGA/ SUPREME/ BAJAJ/ PRINCE.) Note : (a) Two runs of 1.50 sqmm copper cable and one run of 1.50 sqmm copper cable (earth wire) alongwith one run of PVC conduit measured as one unit. (b) Extra length of cable required for connetion to DBs shall deemed to be included in the unit quoted rate and shall not be measured separately. (c) Suitable colour code of wire shall be maintained for phase / neutral / earth). (d) Earth wire shall run inside the conduit.

Supply & fix MCCB DB VTPN 4 ways,with metal double door CRCA sheet steel power coated, IP -54 protection suitable for MCCB as incommer and MCB as out going, 415 volt 3 phase complete with appropriate size copper bus bar and neutral link complete including MCC B 250A, cutting chases to wall for fixing of DB and making good distrubed wall/surface all as required at site complete all as specified and directed by Engr-in charge. Make : Legrand/L&T/ABB/Siemens/Merlin Gerin

Supply & fix MCCB DB VTPN 8 ways,with metal double door CRCA sheet steel power coated, IP -54 protection suitable for MCCB as incommer and MCB as out going, 415 volt 3 phase complete with appropriate size copper bus bar and neutral link complete including MCC B 250A, cutting chases to wall for fixing of DB and making good distrubed wall/surface all as required at site complete all as specified and directed by Engr-in charge. Make : Legrand/L&T/ABB/Siemens/Merlin Gerin

Supply & fixing MCCB 4 Pole of capacity 250 Amps, 50 Hz, 415V with rupturing capacity of 16 kA including spreader terminals with taking down old unserviceable one complete all as specified and directed by Engr-in-Charge. (Make:- L&T/ Siemens/Legrand/ ABB/ Schneider.)

Supply and fixing of MCB SPN 2 way, single door, 230 Volts SPN Metalic Distributition board, concealed flush to wall for mounting MCBs factory made , conforming to IS : 13032 fabricated out of CRCA sheet fitted with DIN channel, neutral link and approriate rated bus bar DBs shall be semi glossy finished with epoxy polyster based powder paint sprayed and backed at high temperature , between powder paint process to ensure smooth finish and protection against corrsion atmosphere. the DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of same make as MCBs, DB shall also be provided with lable marking indicating the incoming and outgoing circuits on all ways as specified, the DBs shall be of IP 43 IK-09 protection class complete all as specified and directed by Engr-in-Charge. (Make : L & T/ ABB/ Legrand/ Schneider/ Seimens / Merlin Gerin)

Supply and fixing of MCB SPN 4 way, double door, 230 Volts SPN Metalic Distributition board, concealed flush to wall for mounting MCBs factory made , conforming to IS : 13032 fabricated out of CRCA sheet fitted with DIN channel, neutral link and approriate rated bus bar DBs shall be semi glossy finished with epoxy polyster based powder paint sprayed and backed at high temperature , between powder paint process to ensure smooth finish and protection against corrsion atmosphere. the DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of same make as MCBs, DB shall also be provided with lable marking indicating the incoming and outgoing circuits on all ways as specified, the DBs shall be of IP 43 IK-09 protection class complete all as specified and directed by Engr-in-Charge. (Make : L & T/ ABB/ Legrand/ Schneider/ Seimens / Merlin Gerin)

Supply and fixing of MCB SPN 8 way, double door, 230 Volts SPN Metalic Distributition board, concealed flush to wall for mounting MCBs factory made , conforming to IS : 13032 fabricated out of CRCA sheet fitted with DIN channel, neutral link and approriate rated bus bar DBs shall be semi glossy finished with epoxy polyster based powder paint sprayed and backed at high temperature , between powder paint process to ensure smooth finish and protection against corrsion atmosphere. the DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of same make as MCBs, DB shall also be provided with lable marking indicating the incoming and outgoing circuits on all ways as specified, the DBs shall be of IP 43 IK-09 protection class complete all as specified and directed by Engr-in-Charge. (Make : L & T/ ABB/ Legrand/ Schneider/ Seimens / Merlin Gerin)

Supply and fixing of MCB SPN 12 way, double door, 230 Volts SPN Metalic Distributition board, concealed flush to wall for mounting MCBs factory made , conforming to IS : 13032 fabricated out of CRCA sheet fitted with DIN channel, neutral link and approriate rated bus bar DBs shall be semi glossy finished with epoxy polyster based powder paint sprayed and backed at high temperature , between powder paint process to ensure smooth finish and protection against corrsion atmosphere. the DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of same make as MCBs, DB shall also be provided with lable marking indicating the incoming and outgoing circuits on all ways as specified, the DBs shall be of IP 43 IK-09 protection class complete all as specified and directed by Engr-in-Charge. (Make : L & T/ ABB/ Legrand/ Schneider/ Seimens / Merlin Gerin)

Supply and fixing miniature circuit breaker (MCB) single pole with thermal overload for inductive load as well as magnetic short circuit tripping device with quick break trip free mechanism robust design and terminals having heat resistant moulding suitable for single phase circuit of 240 volts 06 to 40 Ampere current rating 'B' curve 10 kA breaking capacity complete all as specified and directed by Engr-in-Charge. (Make : L & T/ ABB/ Legrand/ Schneider/ Seimens)

Supply and fixing miniature circuit breaker (MCB) double pole with thermal overload for inductive load as well as magnetic short circuit tripping device with quick break trip free mechanism robust design and terminals having heat resistant moulding suitable for single phase circuit of 240 volts 06 to 40 Ampere current rating 'B' curve 10 kA breaking capacity complete all as specified and directed by Engr-in-Charge. (Make : L & T/ ABB/ Legrand/ Schneider/ Seimens)

Supply and fixing miniature circuit breaker (MCB) Triple pole with thermal overload for inductive load as well as magnetic short circuit tripping device with quick break trip free mechanism robust design and terminals having heat resistant moulding suitable for single phase circuit of 240 volts 06 to 40 Ampere current rating 'B' curve 10 kA breaking capacity complete all as specified and directed by Engr-in-Charge. (Make : L & T/ ABB/ Legrand/ Schneider/ Seimens)

Re-Fixing only MCB SP /SPN/TP/MCCB as obtained from item No-05 above including connected with suitable size of copper lugs complete all as directed .

Supply and fixing of metal socket with sheet metal enclosure single pole and neutral with two pin earth plug and socket complete with one single pole MCB 20 Amp 240 volts half grouting on wall all as specified and directed by Engr-in-Charge. (Make:- L & T/ Legrand/ ABB/ Seimans/Schneider)

Material & Labour for earthing with galvanized steel earth plate electrode of size 60cmx60cmx6mm thick bured directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanized earth lead by means of bolts, nuts check nuts and washers of galvanized iron or steel using GI or steel wire 4mm dia as earthing lead as shown in electrical plate No 3 of SSR Part-I connected to earthing test point all as specified or indicated including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC 1:3:6 type C-1 using 20mm graded stone aggregate pit, funnel, 20mm dia GI medium grade watering pipe, 15mm dia GI medium grade earth lead protection pipe and pre-cast earth pit cover 80mm thick made of RCC (1:1:5:3) type A1 duly reinforced with 8mm dia TMT bar @ 100mm c/c both ways, one lifting handle made out of 10mm dia TMT bar 250mm long embedded in cover slab and cover, wire, copper lugs, etc, mest, charcoal and common salt in alternate layer of 15cm thick including taking down old unserviceable earth plate complete all as specified & directed by Engr-in-Charge. (Note: Each protection pipe and earthing lead upto and including 7.5 meter length is deemed to be included in the quoted rate of this item)

Taking down carefully existing LT feeder piller box outdoor type including electric connection, cable ,accessories, and also remove from existing PCC foundation without any damage etc and refixing/shiftting to new location with complete reconnecting of cable, fittings etc with fresh PCC grounting for foundation at new location complete all as specified .

Dismantling/opening up existing fan size of 1200 mm sweep, taking out all burnt/damaged windings insulating materials & cleaning internally as well as externally, rewinding the fan motor with super enamelled copper wire as per existing size/specification, replacement of complete insulating materials, varnishing drying up, cleaning & greasing of bearing/buses using new grease, reassembling and testing and transporting back to site and refixing to original position. The rates quoted by the contractor shall deemed to include replacement of defective slip pin and roller rubber if worn out and connecting wire of 3 core pvc flexible wire upto 1.0 mtr all as specified and directed by Engineer-in-charge.

-ditto- all as per item No 14.00 above but Celling fan of size 1400 mm sweep.

-ditto- all as per item No 14.00 here-in-before but exhaust fan size 450 mm sweep.

-ditto- all as per item No 14.00 here-in-before but exhaust fan size 225mm -300 mm sweep.

Taking down of ceiling fan / exhaust fan of any size/sweep for overhauling/ servicing comprising dismantaling , cleaning internally and externally including applying one coat of paint and cleaning/lubricating of bearing/buses using fresh lubricant (Oil grease) re-assembling, hanging on same position, connecting and testing for proper functioning complete all as specified and as directed by Engr-in-Charge. Notes: (i) Replacement of defective spares for making the ceiling fan units in satisfactory working condition will be measured & paid separately under relevant items as 'Supply only'. (ii) Labour charges for taking out old spares & refixing of new spares shall deemed to be included in unit quoted rate. (iii) Required defective split pin, roller rubber and suitable connecting wire of same size and core shall deemed to be included in unit quoted rate.

Supply only fan capacitor 2.5 MFD complete all as specified and as directed . (Make :- Bajaj/ Universal/ Usha/Havells.)

Supply only ball bearing/bush for exhaust fan of any size complete all as specified and as directed. (Make : TATA/ NBC/SKF) Note for item No 72.00 & 73.00:- Materials of item No 72.00 & 73.00 to be incorporated in item No 71.00 here-in-before.

Dismantling and taking out defective geyser of any capacity of any make of and rectification of defects including repairing and refixing at same position, connecting and testing for proper functioning complete all as specified and as directed . replacing spares as required , however small pieces of wire terminals, soldering / crimping required at site for proper functioning of the equipment will be deemed to be included in the quoted rate under this item (spares shall be measured and paid separately). Notes: (i) Replacement of defective spares for making the geyser units in satisfactory working condition will be measured & paid separately under relevant items as 'Supply only'. (ii) Labour charges for taking out old spares & refixing of new spares shall deemed to be included in unit quoted rate. (iii) Required small pieces of wire terminals, soldering / crimping and suitable connecting wire of same size and core shall deemed to be included in unit quoted rate.

Supply only the following new spares for geyser of any capacity:-

Thermostat for geyser/solar water heater suitable to work up to 80' C . (Make : Dasspass / Escorts / Racord / Thetta)

Indicator lamp. (Make :- Bajaj/ Universal/ Usha/Havells.)

Inner assembly for geyser 50 Litres capacity. (Make:- As per sample)

Inspection plate for 25/50 Litres capacity. (Make:- As per sample)

PVC connection pipe nylon threaded 15mm dia., 450mm long with chromium plated brass couplings on both ends suitable for 15mm bore tubing. (Make:- Prayag/ polytuff/ Ashirvad)

Heating element 2000 Watt suitable for 50 ltr geyser. (Make :- Theta / Aires / Crown / Dasspass)

Heating element 1500 Watt suitable for 25 ltr geyser. (Make :- Theta / Aires / Crown / Dasspass)

Polycarbonate plug top, 3-pin, 15/16 Amps. (Make:- Anchor / Havells / Kinjal) Note for item No 75.01 to 75.08:- Materials of item Nos. 75.01 to 75.08 to be incorporated in item No. 74.00 here-in-before.

Material and labour for servicing of the solar water heater 500 LPD capacity NPX indirect solar water heating system and making good any leakage replacement of gaskets etc testing complete and making the plant functional including replacement of spare parts complete all as specified and directed by Engr-in-Charge.

-ditto- all as per item No 84.00 above but for 300 LPD capacity.

-ditto- all as per item No 84.00 above but for 200 LPD capacity.

Supply, laying and testing cable XLPE insulated screened PVC bedded, galvanized steel strip , electric power cables (heavy duty) with Aluminium Conductor of size 25 Sqmm 3.5 Core, 1100 Volts grade including cable glands, lugs, Saddling on wall (if required), nuts, bolts and washers of suitable size including taking out old unserviceable cable complete all specified and as directed by Engineer-in-Charge. (Make : Finolex/Universal cables/RPG/ KEI Industries)

Supply, laying and testing cable XLPE insulated screened PVC bedded, galvanized steel strip , electric power cables (heavy duty) with Aluminium Conductor of size 50 Sqmm 3.5 Core, 1100 Volts grade including cable glands, lugs, Saddling on wall (if required), nuts, bolts and washers of suitable size including taking out old unserviceable cable complete all specified and as directed by Engineer-in-Charge. (Make : Finolex/Universal cables/RPG/ KEI Industries)

M/s Adhikari construction co.

M/S ANIL KUMAR

Surjit and Sons

P S TRADERS

SNOWY ENGINEERING INC

GURBUX SINGH AND CO.

M/s Dhapola Elevator and Engineering