Beautification work of Model Auditorium of Madhepura Town Hall, Nagar Parishad Madhepura.

Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed.

All Kind of Soil

Extra for providing and mixing water proofing material in cement concrete work in the proportion recommended by the manufacturers.

For PCC

Reinforced Cement Concrete Works

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works up to plinth level (M 25 Grade )

All works up to plinth level (M 30 Grade )

All work above Plinth level upto floor V Level (M 25 Grade)

Shuttering & Reinforcement Steel Work

Centring and shuttering including strutting,propping etc. and removal of formwork for.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

Cement mortar 1:6 (1 cement: 6 coarse sand )

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:

Twin Rubber Stopper

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (overall area of door shutter to be measured)

2nd Class Teak Wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S.pressed butt hinges bright finished of required size with necessery screws, excluding panelling which will be paid for separately, all complete as per direction of Engineerin-charge.

Second Class teak wood-

35 mm thick

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Plastering & Finishing Work

12 mm cement plaster of mix:

1:4(1 cement :4 coarse sand)

6 mm cement plaster to ceiling of mix :

1:4(1 cement: 4 coarse sand)

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

New work (Two or more coat applied @ 1.67 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and softwood)

Steel Work

Providing and fixing steel glazed doors, windows and ventilatrs of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with woodenplugs and screws or raw) plugs and screws or with fixing dips or with bolts and nuts as required, including providing and fixing of glass panes with glazing dips and special metal-sash putty pf approved make complete including applying a priming coat of approved steel primer; excluding the cost of metal beading and other fitting except necessary hinges or pivots as required.

Doors

Providing and fixing pressed steel door confirming IS code 4351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and,applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

CARRIAGE OF MATERIALS

Supplying and fixing metal/ PVC box of following sizes ( nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in the front including painting etc. as required.

(a)75mmX75mmX50mm deep

(b)200mmX150mmX60mm deep

Supplying & fixing of following size medium class PVC conduit along with accessories in surface/ recess including cutting of wall and making good the same in case of recessed conduit as required.

(a) 20 mm dia

(b) 25 mm dia

Supplying and fixing following size/modules, GI box along with modular base & cover plate for modular fitting in recess etc. as required.

(a)75mmX75mm

DSR2022 E&M

(i) For 4 way Double door TPN MCB DB

(Ii) For 6 way Double door MCB TPN DB

(iii) For 8 way Double door MCB SPN DB

6 Amp. To 32 Amp. SP MCB 240 Volt

32 Amp TPN MCB 415 Volt

40 Amp TPN MCB 415 Volt

32 Amp SPN MCB 415 Volt

Supplying and fixing of following rating electrical items in the existing cubical panel board including drilling holes in cubicle panel making connections etc. as required .

(i) 250 Amp 36 KA FP 415 volt MCCB.

(ii) 250 Amp, 4 pole changeover switch .

(iii) 32 Amp TPN MCB 415 Volt

(iv)32 Amp SPN MCB 240 Volt

(v) 40 Amp TPN MCB 415 Volt

(vi) 100 Amp 16 KA FP 415 volt MCCB.

(vii) 100 Amp, 4 pole changeover switch .

(viii) Copper strip of all sizes.

(ix) Digital ammeter three phase

(x)Digital Voltmeter three phase

(xi)Pilot lamp for indicator

Supplying and fixing following types lamp in existing electrical fitting/ fixture etc as required.

(i) 10/12watt LED lamp

Laying of one number PVC insulated and PVC sheathed/ XLE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushionig, protective covering and refilling the trench etc. as required.

(a) Above 95 sq. mm. and upto 185 sq.mm

Laying and fixing of one number PVC insulated and PVC sheathed aluminium conductor cable of1.1 KV grade of following size on surface etc. as required.

(a)Above 95 sq. mm. and upto 185 sq.mm (Clamped with 25/40x3 mm MS flat clamp)

Providing and laying following size NP2 (Non pressure) RCC pipe complete with RCC collar etc. as required .

(a) Dia 300 mm.

DSR 2022 E&M

(a) Above 95 sq. mm. and upto 185 sq.mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade as reguired.

(a) 3.5 Core 185 sq mm

DSR 2022 E&M 1.53.1

HSR 2021 PH233

DSR 2022 E&M 17.2.1

DSR 2022 E&M 17.2.3

DSR 2022 E&M 17.2.9

DSR 2022 E&M 17.2.4

DSR 2022 E&M 17.1.5

DSR 2022 E&M 17.2.10

DSR 2022 E&M 17.2.14

DSR 2022 E&M 17.2.15

50 mm dia

80 mm dia

150 mm dia

200 mm dia

80 mm dia

100 mm dia

150 mm dia

200 mm dia

Providing and fixing forged brass bail valve with forged brass ball (suitable for test pressure of not less than 15 kg / sq.cm of the following size:

25 mm dia

80 mm dia

150 mm dia

200 mm dia

100 mm dia

150 mm dia

200 mm dia

TOTAL

Chilled Water insulated pipe

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class ‘O’ insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect.

200 mm dia (32mm Thick Insulation)

150 mm dia (32mm Thick Insulation)

125 mm dia (32mm Thick Insulation)

100 mm dia (32mm Thick Insulation)

80 mm dia (32mm Thick Insulation)

40 mm dia (32mm Thick Insulation)

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified

125 mm dia

100 mm dia

80 mm dia

40 mm dia

40mm dia.

40 .mm dia

40 mm dia

DSR 2022(E&M) 16.12.1

Thickness 0.63 mm sheet

Thickness 0.80 mm sheet

Thickness 1.00 mm sheet

Thickness 1.25 mm sheet

Damper

Actuator

Fire Damper

Actuator

Thermal Insulation

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class “O”) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.

Acoustic Lining of Ducts

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications.

25 mm Dia

40 mm Dia

25 mm Dia

Description of Work

ACOUSTIC SYSTEM

FURNITURE'S

AUDIO & VISUAL SYSTEM

ELECTRICAL FITTING'S

FDA 600 AUD

FIRE FIGHTING 600 AUD

Estimated Cost

In Digit

Item Description

Wall Treatment

Micro Perforated Acoustic Panels (16mm) for walls @ 8 feet from FFL

Sound slat paneling (16mm) for walls above 8 feet to ceiling level

Composite acoustic panels( 25 mm )above 8 feet to ceiling level

SITC of LED profile light with housing 120 bulbs per mtr in wall including labour and electrical cables, alluminium profile size = 25 x 12mm depth. With diffusser. LED LIGHT = ILLUMAX / ACOUSTIKA /USHA

SITC of 12 V Power Supply Adaptor 32 ampere Make- ILLUMAX / ACOUSTIKA /USHA

Acoustic Ceiling

Micro Perforated Acoustic Paneling (16mm) on ceiling

GYPSUM CEILING

Floor

Wooden Flooring

Acoustic Door

Acoustic Door

SITC of double leaf panic bar with trim. Make- DORWIN/DORMA/HETTICH

SITC of door closers. Make- DORWIN/DORMA/HETTICH

Step lights

SITC of Step Light With UP & Down Throw With Seat Number Make- ILLUMAX / ACOUSTIKA / PHILIPS

SITC of 12 V Power supply adaptor 25 Ampere Make- ILLUMAX / ACOUSTIKA / PHILIPS

STAGE

SITC of Stage false ceiling of 12 mm thick Black PFB panels of size1200 x 600 mm laid over MS Suspension Grid consisting of 2 nos 40 X 40X 5mm MS Angles, welded back to back @1200mm c/c & M.S. Tees @ 600mm c/c . Make- MS = TATA/ JINDAL / APOLLO PFB PANEL = ACOUSTIKA / ECOPHON/ARMSTRONG

STAGE FLOORING

PROSCENIUM

SITC of LED par 54 x 3 RGBW indoor Light source : 54PCS 3W LEDs(R12 G12 B12 W18) Lens angle : 25º(30º, 45º, 60º optional) Channel mode : 3 / 4 / 6 / 7 / 9DMX channel mode 0-100% linear dimmer Function : color mix, automatic color change, built-in program and strobe effect with adjustable speed Sound controlled via built-in microphone Adjustable sound sensitivity LED Display, easy to control Control : auto, sound active, DMX512, software(connect to computer) Overheating protection Voltage : 100-220V,50/60hz Power : 180W Make- Basel/PLS/Robe

SITC of moving head Lamp : 10R 280W Power : 350 W Life Time : 2200 Hours Color Temperature : 8000K DMX Channel : 16 CH Pan Scan : 540º (16bit) Tilt Scan : 270º (16bit) Color Wheel : 8 Facet rotating prism + frose + shake Strobe : 0.5-9 f/s, random or pulse flash, speed adjustable, strobe macro function Dimmer : 0%-100% mechanical Beam Angle : 0%-4% mechanical Make- Basel/PLS/Robe

SITC of PC spot 200 watt original citizen led lamp flicker free led light source 1 Pc. 200 watt COB LED (WWCW) zoom DMX control lamp average life time 50,000 hours DMX channel 2/3/4 channel control mode DMX 512 software (connect to computor) manual control dimmer 100% linearly adjustable strobe 0 - 25 FPS angle 15 to 50 digree Make- Basel/PLS/Robe

SITC of Profile light LED 200W PROFILE WITH PLASTIC HOUSING (26 DEGREE)Lux@2m 11000 Lux Lux@4m 2700 Lux Lux@6m 1190 Lux Lux@8m 700 Lux LED Qty 1pcs of 200W LED Drive current 5A Color temperature 3200K (warm White) On-board Control Four Display Control Protocol DMX512 CRI 80 Channel Mode 1CHs Dimmer 0~100% Beam Angle 26º (19ºOptional) Make- Basel/PLS/Robe

SITC of 24x 12 RGBW Light source : 24PCS 12W 4 IN 1 LEDs Lens angle : 25º(30º, 45º, 60º optional) Channel mode : 3 / 4 / 6 / 7 / 9DMX channel mode 0-100% linear dimmer Function : color mix, automatic color change, built-in program and strobe effect with adjustable speed Sound controlled via built-in microphone Adjustable sound sensitivity LED Display, easy to control Control : auto, sound active, DMX512, software(connect to computer) Overheating protection Voltage : 100-220V,50/60hz Power : 300W Make- Basel/PLS/Robe

SITC of and fixing COB Led par 200 watt LED PAR COB white • Flicker free • Built-in programs • LED Light Source: 1pcs 200-watt COB LED lamp (WW/CW) • Lamp average lifetime: 50,000 hours • DMX channel: 2 channels • Control Mode: Auto, Master/Slave, DMX512, software (connect to computer), sound control • Dimmer: 100% linearly adjustable • Strobe: 0~25F.P. S • Voltage: AC100-240V 50/60Hz • Power: 200W • Working Environment: indoor -20°C- 40°C • IP Rating: IP20 Make- Basel/PLS/Robe

SITC of Fresnel light 150w COB LED Drive Current 5A Color Temperature 3200k CRI 97 Input Voltage 100-240VAC Power 160W on-board Four digital display Control Protocol DMX512 DMX Channel 2Chs Dimmer 0-100% lux@2m (Minimum facula) - 7500 Lux @4m (Minimum facula) - 2130 Lux lux@6m (Minimum facula) - 970 Lux lux@8m (Minimum facula) - 550 Lux lux@2m (Minimum facula) - 217 Lux lux@4m (Minimum facula) - 578 Lux lux@6m (Minimum facula) - 270 Lux lux@8m (Minimum facula) - 165 Lux Make- Basel/PLS/Robe

SITC fog machine With the latest technology of the heater, the ZB-3000 has better effects as a fog machine Power : 3000W Heat-up Time : 12 minutes Fluid consumption rate : 45min/L (100% output), 2hours/L (30%output) Tank capacity : 10L Circuitry Contro : Remote Control DMX : 512 Control Make- Basel/PLS/Robe

SITC Cyclorama Wall washers are a type of lighting fixture commonly used in indoor and outdoor settings to create a wash of light on walls, and cyclorama screen They are particularly useful for creating mood lighting Control Mode: Auto, Master/Slave, DMX512, software (connect to computer), sound control Dimmer: 100% linearly adjustable Working Environment: indoor -20°C- 40 °C DMX Channel: 4, 6, 7, 9, 3 channel Lamp average lifetime: 50,000 hours LED Light Source: 18pcs 12-watt 4IN1 LEDs (RGBW) Voltage: AC90-260V 50/60Hz Make- Basel/PLS/Robe

SITC of 400W LED Blinder Light . 400W LED Blinder Light 30 Degree complete with 3200K/5600K CCT 4x100W Chip On Board LED lamp source, DMX 512 dimming with 4/8 Channel modes, Black finish housing, IP20 protection having Strobe option and smooth dimming, illuminate Stage with uniform light intensity levels Make- Basel/PLS/Robe

SITC and fixing of DMX splitter 1 in 10 out Voltage : 100-220V,50/60hz Power : 4W IP rating : IP20 isolated DMX output ports 3pin XLR inputs & outputs 10 isolated outputs DMX loop through port with inbuilt termination Universal power supply Make- Basel/PLS/Robe

SITC of XLR connectors Make- custom

SITC of DMX cable 24 AWG (25/0.10mm) x 2 core ATC copper conductor, PE insulated, core twisted in a circular form, covered with special moisture-proof polymer, spiral shielded (97%) with ATC copper, outer Jacketed with Matt finish High Flex Special PVC. Make- Tasker/PLS/Netmas

SITC of stage light clamps Make- Make- Basel/PLS/Robe

SITC of Stage light light point Wiring from light points to MCB box wire 2.5 Sq.mm 3 Core PVC Insulated and PVC Sheathed Cable including of suitable size 5/6 amps sockets with box, and top sutable MCBs and MCB box.. Socket, top and MCBS make- Anchor/Schnieder/Havells/Hager, Electrical cable make- Polycom/Havells/eq

Supply of 4 Side ladder made out of 25 x 50 mm flate ms pipe Make- Make- Tata/Jindal/Apollo

Supply and fixing of Motorized FOH light bar Supply of Motorised lighting bars with 2 HP 3 phase Crompton motor,30:1 ratio gear box,Drum,50mm OD G.I.Pipe,with 5 line pully with 6mm rope for pully the lighting bar & 8mm rope used in drum for up/down,2 nos siemens/L&T contactor switch for reverce /forward,2 nos micro switch for cut off & 3 nos push button for up/down/stop position. Make- Make- Basel/PLS/Robe

SITC of stage light bar 50 mm dia MS pipe will hang from ceiling grid 57 feet Make- Make- Tata/Jindal/Apollo

SITC of MS Perforated 75mm Wide Cable Tray with Lid, . Make: Basel/Clay Paky/ Robe

SICT of MAIN CURTAIN made out of velvet curtain cloth with horizontal sliding arrangement complete with fixing rails, brackets, sliding arrangement & motorized operation complete with runners, master runners, pullies, 3mm steel wire rope, 1 HP motor (Crompton) 2nos., Air breaker contactors (L&T/SIEMENS), 2nos. micro switches for auto stop, 3 nos push buttons for forward, reverse and stop positions. The curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900mm and should be stitched in double gathering Size 57 x 25' aprx. ,Curtain Fabric Make- Outivie/Reliance/Nexgen. Mechanism Make- DL&MC/PLS/Basel

SITC of REAR CURTAIN - made out of outvie velvet curtain cloth with horizontal sliding arrangement complete with fixing rails, brackets, sliding arrangement & motorized operation complete with runners, master runners, pullies, 3mm steel wire rope, 1 HP motor (Crompton) 2nos., Air breaker contactors (L&T/SIEMENS), 2nos. micro switches for auto stop, 3 nos push buttons for forward, reverse and stop positions. The curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900mm and should be stitched in double gathering Size 57' x 25' aprx. Curtain Fabric Make- Outivie/Reliance/Nexgen. Mechanism Make- DL&MC/PLS/Basel

WINGS :- Supply Installation testing and commissioning of velvet cloth outvie black fabric as per approved sample fixed over the metal framework metal framework made out of 2"x 2" squre MS pipe and 8 mm ply from one side specification complete. Measurement will be made for external dimensions including heading for payment Size 25' x 4' MS material Make- Tata/Jindal/Apollo ply make- Green/ Century/ Merino Fabric make- Outivie/Reliance/Nexgen

FRILLS :-Supply Installation testing and commissioning of frills in double gathering box pleats stiched ou of valvet fabric of The frill to be fixed from the suspension grid with 38 mm dia B class ms pipe suitably hung by mean of 35x4mm MS flat. The pipe & flat to be painted with black enamel paint size 57' x 3' MS material Make- Tata/Jindal/Apollo ply make- Green/ Century/ Merino Fabric make- Outivie/Reliance/Nexgen

CYCLORAMA CUM SCREEN :-Supply Installation testing and cyclorama MS Frame. The fixed on tubular frame made out of 48 OD mm dia M.S. pipe and 25 mm ms for support curtain Cum screen in matte white Material. The screen. Size - 40 feet x 20 feet MS material Make- Tata/Jindal/Apollo, Screen make- Galalite/Grandview/Harkness

Proposed Model

Audi Chair Without writing pad

VIP Sofa 3 Seater

VIP Sofa 1 Seater

Centre Table

Corner Table

Recliner

Item Description

Supply, installation, testing and commissioning of 3 chip DLP/3LCD projector with 13000lumens or better brightness or better and Colour Light Output also 13000lumens or better at native WUXGA Resolution. The projector shall have typical lifetime of 20,000 hours and contrast ratio of 500000:1 or more.The projector shall have HDMI x 1,3GSDI x 1 (BNC),DVI-D x 1 HD15 x 1, USB x 1 (type B mini), USB x 1 (type A), WiFi dongle (optional),HDBaseT (RJ45 x 1),RJ45 x 1 signal Input and 3GSDI x 1 (BNC) , DVI-D x 1 (digital only) signal Output.The projector shall have RS232 In,Control via HDBaseT,Ethernet (10/100) RJ45. Shall include suitable lens as required complete with standard accessories as per tender specifications. Approved Make: Christie/Barco/Sony/NEC The bid must be submitted along with Manufacturer / OEM Authorization & OEM of this item with step-by-step compliance against technical specifications.

Supply, Installation, Testing and Commissioning of Customized Heavy-Duty Projector Mount Kit for above Projector complete with satandard accessories as required. Approved Make: Custom

Supply ,installation ,testing and commissioning of 300" Diagonal Tab Tensioned (AR 16:10) Motorised Projection Screen Matte white, Projection Surface, builtin motor system with IR/RF receiver, high gain & viewing angle , Noise less Up/Down operation, etc. all complete. Approved Make: Suvira/Netmas/Sudpi The bid must be submitted along with Manufacturer / OEM Authorization & OEM of this item with step-by-step compliance against technical specifications.

SITC of Wallplate Transmitter over Cat 6( HDBaseT) upto 70 meter with Inputs 1 HDMI, 1 USB-C & 1 Cat6 (HDBaseT) Output, 2K and 4K support, HDCP 1.4 & 2.3 both Compliant, Up to 60W USB–C charging on USB-C input, PoE acceptor, stereo audio output, 1 RS-232 for device control & 1 RS232 for serial link extension over HDBaseT output, Safety Regularity Compliance : CE, RoHs and WEEE, ISO 9001, ISO 14001, ISO 27001:2013 etc complete as required. Approved Makes:Lightware/ Kramer/ RGB Spectrum

SITC of 4K PTZ Camera with 12x Optical Zoom and 16x digital zoom, 4K 60fps clear video, 8.51 megapixel CMOS image sensor, Ultra–low CMOS image sensors plus 2D and 3D DNR technology, 255 presets views, Plug and play connection with a USB cable, USB 3.0: On a USB type B connector, HDMI output on HDMI connector, 3G-SDI output on BNC connector, Audio Line In: On a 3.5mm mini jack, RJ-45: 10/100/1000M Adaptive Ethernet Port, RS-232 IN & Out: : On 8 pin Min DIN connectors, RS-485: On a 2–pin phoenix connector,Video resolutions: 1080P60, 1080P50, 1080I60, 1080I50, 1080P30, 1080P25, 720P60, 720P50, 1080P29.97, 1080I59.94, 1080P59.94, 720P59.94, 4KP29.97, 4KP25, 4KP30, Lens: 12x, f = 4.4mm ~ 52.8mm, F1.8 ~ F2.6, Backlight Compensation: Support, Video S/N: ≥55dB, Horizontal Angle of View: 71° ~ 8.2°, Vertical Angle of View: 42.7° ~ 4.5°, Horizontal Rotation Range: ±170°, Vertical Rotation Range: ±30°, Pan Speed Range: 1.6°/s ~ 76°/s, Tilt Speed Range: 0.5°/s ~ 15°/s, H & V Flip: Support, Control options: Embedded web pages, RS–232 protocol and IR transmitter remote included, Certification: Safety: CE, FCC & Environmental: RoHs, Reach, etc. Approved Makes:Sony/ Kramer/ Vaddio

SITC of Wireless presentation & Video conferencing devices supports video resolution upto 4K, with HDMI content input, 1 HDMI & 1 Display Port output, 1 Ethernet port, 5 USB port for connecting keyboard, mouse, USB camera, USB mics, etc, Supports iOS, Windows and Android operating systems, display minimum 6 users screen with 1 display & 12 users screen using 2 displays, Supports DHCP, Audio out, supports annotation & whiteboard feature, content can be watched on connected smartphones, iPhone, iPad, Laptops, MacBooks & at the same time users can zoom the content for clarity & do annotation from their devices. User can install any third party application on the device like MS Teams/Zoom/Blue Zeans/Any soft VC App. Device can be used for soft VC application, connect 100 participants simultaneously, Certification: CE, ISO 9001, ISO 14001, OHSAS 18001, etc. Approved Makes:Mersive/ Kramer/ Screenbeam

SITC of 1:10 4K@60 4:4:4 HDMI Distribution Amplifer, 1 HDMI inputs & 10 HDMI outputs, HDCP 2.2 signal compliance, HDR10 support, HDMI support - deep color, x.v.Color™, lip sync, 7.1 PCM, Dolby TrueHD, DTS–HD, CEC (OUT 1 only), 2K, 4K, and 3D as specified in HDMI 2.0, 1 RS-232 for service, etc. Approved Makes:Lightware/ Kramer/ RGB Spectrum

SITC of HDMI Transmitter over Cat 6 ( HDBaseT) up to 100m with Input 1 HDMI, Cat6 (HDBaseT) Output, 4K@60 4:4:4 support HDTV Compatible, HDCP 2.2 Compliant with CEC, IR and RS-232, Compliance : CE, ISO 9001, ISO 14001, OHSAS 18001, etc complete as required. Approved Makes:Lightware/ Kramer/ RGB Spectrum

SITC of HDMI Receiver over Cat 6 ( HDBaseT) up to 100m with Input 1 Cat6 (HDBaseT), 1 HDMI Output, 1080p, 2K and 4K support, HDTV Compatible, HDCP 2.2 Compliant with IR and RS-232, Compliance : CE, ISO 9001, ISO 14001, OHSAS 18001, etc complete as required. Approved Makes:Lightware/ Kramer/ RGB Spectrum

SITC of Control System should be equipped with at least 8 bidirectional RS-232 serial ports, at least 8 IR ports, at least 8 Digital I/O ports, at least 8 low voltage relays for controlling room functions, at least 1 Ethernet monitoring and control port, Rack mounting (1U), It should have minimum 5 license each included for both iOS & Android application, Certification: CE, ISO 9001, ISO 14001, OHSAS 18001, etc. Approved Makes:Lightware/ Kramer/ Seada

SITC of 10 inch IPS color screen Touch panel, screen resolution 1280 X 800, brightness 350cd/m2, contrast ratio 800:1, 16:10 aspect ratio, Wi-fi connectivity, Ethernet Communication RJ45 port, inbuilt speaker & mic, etc. Should be supplied with table mount as well as wall mount kit.Should have appropriate app, support native integration of same OEM enterprise management software. Certification: CE, ISO 9001, ISO 14001, OHSAS 18001 etc. Approved Makes:Lightware/ Kramer/ Seada

SITC of Control Keypad with 12 buttons & volume knob, Should have communication port to communicate with control sysyem, 1 IR Sensor: For IR learning, Control ports: 2 IR, 4 Relay, 3 RS-232, 1 RS-485, 2 I/O, 1 Ethernet, 1 mini USB, DHCP supported, Certification CE, ISO 9001:2008, etc. Approved Makes:Lightware/ Kramer/ Seada

SITC of Wi-Fi Router with 2.4 GHz WLAN, WPS, 5 GHz WLAN, 4 LAN ports , Should have reset button & power switch, Should be 802.11ac Wi-Fi specification, WPA/WPA2 encryption to secure your wireless traffic, etc. Approved Makes: D-Link/Netgear/Cisco

Supply and Laying of 6ft 4K HDMI patch cord in existing conduit. Approved Makes:Lightware/ Kramer/ RGB Spectrum

Supply and Laying of 3 ft USB 3.1 GEN–2 Cable USB–C (M) to USB–C (M) patch cord, Transfer Rates Up to 10Gbps, PC, Mac & Mobile Compatible, in existing conduit. Approved Makes:Lightware/ Kramer/ RGB Spectrum

Supply and Laying of 3.0 Meters 3.5mm to Single IR Emitter Cable. Approved Makes:Lightware/ Kramer/ Seada

Supply and Laying of HDBaseT recommanded 23 AWG shielded CAT6A Cable with appropriate connectors in existing conduit. (300 Mtrs Spool) Approved Makes:Lightware/ Kramer/ RGB Spectrum

Supply and Laying of STP connector for 23 AWG shielded CAT6A Cable. Approved Makes:Lightware/ Kramer/ RGB Spectrum

Supply of Main FOH flyable array module, 2 way, bi- amplified, 2 x 8" Low Distortion Transducers, 3" VC or better transducers, frequency Response (+/-3 dB): 52 Hz - 20 kHz or better. The Sensitivity (SPL / 1 W @ 1 m) > 102 dB .Coverage Pattern - 140° x 20° ,The Maximum SPL @ 1 m >139 dB . The Long-Term Power Handling is LF: 900W Continuous, 3600W Peak, HF: 200W Continuous, 800W Peak should be made by Marine Birchwood Cabinet of Premium Grade . Approved Makes: OHM, British Acoustics, D&B, Martin Audio, L-Acoustics, Renkus Heinz The bid must be submitted along with Manufacturer / OEM Authorization & OEM of this item with step-by-step compliance against technical specifications.

Supply, Installation, testing and commissioning of Small Array frame for flying Array Modules.

Supply of Main FOH Subwoofer with Frequency Response (+/-3 dB) 32 Hz - 190 Hz or better, the nominal dispersion is omnidirectional, Power Handling, long-term continuous : 2000 W (1000 W per woofer) ; Power Handling, Peak : 8000 W (4000 W per woofer) ; Sensitivity (SPL / 1 W @ 1 m) : 101 dB ; Calculated Maximum SPL @ 1 m : 144 dB ; Transducer Size : 2 x 18" Ultra Low Excursion ADR Drivers, 4" VC - Ferrite ; Nominal Impedence : 4 Ω Approved Makes: OHM, British Acoustics, D&B, Martin Audio, L-Acoustics, Renkus Heinz The bid must be submitted along with Manufacturer / OEM Authorization & OEM of this item with step-by-step compliance against technical specifications.

Supply, Installation, Testing & Commissioning of Software Controlled Digital DSP with below Specifications:- Number of Inputs - 4, Number of Outputs - 8, Input Impedance - 12kΩ unbalanced, 24 kΩ balanced CMMR - >45 dB Adjustable Delay - 1 second / input & 1 second / output Approved Makes: OHM, British Acoustics, D&B, Martin Audio, L-Acoustics, Renkus Heinz, Powersoft, Lab Gruppen The bid must be submitted along with Manufacturer / OEM Authorization & OEM of this item with step-by-step compliance against technical specifications.

Supply Installation Testing Commisioning of a Vocal Condenser Microphone with the below specifications:- Type: Electret Condenser, Polar Pattern: Super Cardioid, Freq. Response: 80-18 kHz, Max SPL: 150 dB, Studio Grade Large Mic Diaphragm, All Metal Housing, Mute Switch, Foam Protector for protection against wind & pop noise, Anti Glide Mic holder, Working Volatge: 48V DC Phantom Power Approved Makes: Shure, OSL, Sennheiser, Beyerdynamic The bid must be submitted along with Manufacturer / OEM Authorization & OEM of this item with step-by-step compliance against technical specifications.

Supply Installation Testing Commisioning of an Instrument Condenser Microphone with the below specifications:- Type: Hybrid Condenser, Polar Pattern: Cardioid, Freq. Response: 80-18 kHz, Max SPL: 129 dB, All Metal Housing, Mute Switch. Approved Makes: Shure, OSL, Sennheiser, Beyerdynamic The bid must be submitted along with Manufacturer / OEM Authorization & OEM of this item with step-by-step compliance against technical specifications.

Supply of Wireless Handheld Microphone with Cardioid Pattern , Oeprating Range: 100 ft Line of Sight, Mute Switch, Steel Mesh Grille, RF Output - 30 mW, RF Range 100m Line of Sight, Operation Time - 8 Hours, or better. Approved Makes: Shure, OSL, Sennheiser, Beyerdynamic The bid must be submitted along with Manufacturer / OEM Authorization & OEM of this item with step-by-step compliance against technical specifications.

Supply of Headset/ Lapel Microphone with Cardioid Pattern, Oeprating Range: 100 ft Line of Sight,Mute Switch, Steel Mesh Grille, RF Output - 30 mW, RF Range 100m Line of Sight, Operation Time - 8 Hours, or better. Approved Makes: Shure, OSL, Sennheiser, Beyerdynamic The bid must be submitted along with Manufacturer / OEM Authorization & OEM of this item with step-by-step compliance against technical specifications.

Supply, Installation, Testing & Commissioning of a Flag Antenna Kit with the below specifications:- Complete wireless antenna distribution kit with (2) Flag Antennas, antenna amplifier & a signal splitter. Approved Makes: Shure, OSL, Sennheiser, Beyerdynamic The bid must be submitted along with Manufacturer / OEM Authorization & OEM of this item with step-by-step compliance against technical specifications.

Supply of a 32 Channel Digital Mixer with the below specifications:- 32 Input Channels, 16 Output Channels 2 Touchscreen Control Wings, 96kHz Audio Processing Sample Rate, Dedicated Plugin Server with Dugan Automixing capability, Complete with Flightcase and covers, With a 16 Channel Stagerack Approved Makes: Digico, Avid, Waves, SSL

Supply Installation Testing & Commissioning of a 2.5 Sq. mm, 2 Core Speaker Cable with the below specifications:- Core Arrangement : 2, Gauge : 2.5 sq. mm Material : Stranded Bare Copper - Oxygen Free, Shielding : Unshielded, Jacket Material : TPR, Bend Radius: 4x Diameter Approved Makes: LYNQ, Belden, Draka, Netmas

Supply, installation, testing & Commissioning of 18 AWG (24/0.20mm) x 2 core ATC copper conductor, PE insulated, core twisted in a circular form, Inner sheathed with moisture Proof Polymer, braid shielded (80%) with ATC copper, outer Jacketed with Matt finish Rugged Flexible PVC. Approved Makes: LYNQ, Belden, Draka, Netmas

Supply, installation, testing and Commissioning of 36 U Equipment rack to house all rack mountable equipment, with internal wiring, front glass door,heat dissipation fans,power distribution units etc.complete with standard accessories as required. Approved Make: Valrack/Chief/Middle Atlantica/netmas

DSR 2021 / BSR 2022 /

Air Handling Unit

100 .mm dia

80 .mm dia

40 .mm dia

Condensate Drain Piping

Supply, Installation, Testing and Commissioning of CPVC drain piping, 6 Kg pressure rating complete with fittings, supports as per specifications and insulated with 6 mm thick Oxide acetate foam including with Chase cutting and repairing as per specifications and drawings etc complete as required.

AIR DISTRIBUTION SYSTEM

Supplying & laying of following 1100 volt grade XLPE insulated PVC sheathed Aluminium conductor armoured cables including , clamped includes anchor fastners wall with suitable clamps, saddles fixing bolts including connecting testing and commissioning etc as per specification complete as required.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, three core cable in the surface recessed /PVC /MS conduit etc as per specification complete as required.

Iteam no

50 mm dia

Electrical Driven Main Pump

Diesel Engine Driven Pump

Jockey Pump

80 mm Dia/100 mm dia

Expansion Bellow 200 mm dia

Expansion Bellow 150 mm dia

Expansion Bellow 100 mm dia

Expansion Bellow 80 mm dia

SOR Ref No.

Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed.

All Kind of Soil

Extra for providing and mixing water proofing material in cement concrete work in the proportion recommended by the manufacturers.

For PCC

Reinforced Cement Concrete Works

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works up to plinth level (M 25 Grade )

All works up to plinth level (M 30 Grade )

All work above Plinth level upto floor V Level (M 25 Grade)

Shuttering & Reinforcement Steel Work

Centring and shuttering including strutting,propping etc. and removal of formwork for.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

Cement mortar 1:6 (1 cement: 6 coarse sand )

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:

Twin Rubber Stopper

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (overall area of door shutter to be measured)

2nd Class Teak Wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S.pressed butt hinges bright finished of required size with necessery screws, excluding panelling which will be paid for separately, all complete as per direction of Engineerin-charge.

Second Class teak wood-

35 mm thick

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Plastering & Finishing Work

12 mm cement plaster of mix:

1:4(1 cement :4 coarse sand)

6 mm cement plaster to ceiling of mix :

1:4(1 cement: 4 coarse sand)

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

New work (Two or more coat applied @ 1.67 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and softwood)

Steel Work

Providing and fixing steel glazed doors, windows and ventilatrs of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with woodenplugs and screws or raw) plugs and screws or with fixing dips or with bolts and nuts as required, including providing and fixing of glass panes with glazing dips and special metal-sash putty pf approved make complete including applying a priming coat of approved steel primer; excluding the cost of metal beading and other fitting except necessary hinges or pivots as required.

Doors

Providing and fixing pressed steel door confirming IS code 4351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and,applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

CARRIAGE OF MATERIALS

Supplying and fixing metal/ PVC box of following sizes ( nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in the front including painting etc. as required.

(a)75mmX75mmX50mm deep

(b)200mmX150mmX60mm deep

Supplying & fixing of following size medium class PVC conduit along with accessories in surface/ recess including cutting of wall and making good the same in case of recessed conduit as required.

(a) 20 mm dia

(b) 25 mm dia

Supplying and fixing following size/modules, GI box along with modular base & cover plate for modular fitting in recess etc. as required.

(a)75mmX75mm

DSR2022 E&M

(i) For 4 way Double door TPN MCB DB

(Ii) For 6 way Double door MCB TPN DB

(iii) For 8 way Double door MCB SPN DB

6 Amp. To 32 Amp. SP MCB 240 Volt

32 Amp TPN MCB 415 Volt

40 Amp TPN MCB 415 Volt

32 Amp SPN MCB 415 Volt

Supplying and fixing of following rating electrical items in the existing cubical panel board including drilling holes in cubicle panel making connections etc. as required .

(i) 250 Amp 36 KA FP 415 volt MCCB.

(ii) 250 Amp, 4 pole changeover switch .

(iii) 32 Amp TPN MCB 415 Volt

(iv)32 Amp SPN MCB 240 Volt

(v) 40 Amp TPN MCB 415 Volt

(vi) 100 Amp 16 KA FP 415 volt MCCB.

(vii) 100 Amp, 4 pole changeover switch .

(viii) Copper strip of all sizes.

(ix) Digital ammeter three phase

(x)Digital Voltmeter three phase

(xi)Pilot lamp for indicator

Supplying and fixing following types lamp in existing electrical fitting/ fixture etc as required.

(i) 10/12watt LED lamp

Laying of one number PVC insulated and PVC sheathed/ XLE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushionig, protective covering and refilling the trench etc. as required.

(a) Above 95 sq. mm. and upto 185 sq.mm

Laying and fixing of one number PVC insulated and PVC sheathed aluminium conductor cable of1.1 KV grade of following size on surface etc. as required.

(a)Above 95 sq. mm. and upto 185 sq.mm (Clamped with 25/40x3 mm MS flat clamp)

Providing and laying following size NP2 (Non pressure) RCC pipe complete with RCC collar etc. as required .

(a) Dia 300 mm.

DSR 2022 E&M

(a) Above 95 sq. mm. and upto 185 sq.mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade as reguired.

(a) 3.5 Core 185 sq mm

DSR 2022 E&M 1.53.1

HSR 2021 PH233

DSR 2022 E&M 17.2.1

DSR 2022 E&M 17.2.3

DSR 2022 E&M 17.2.9

DSR 2022 E&M 17.2.4

DSR 2022 E&M 17.1.5

DSR 2022 E&M 17.2.10

DSR 2022 E&M 17.2.14

DSR 2022 E&M 17.2.15

50 mm dia

80 mm dia

150 mm dia

200 mm dia

80 mm dia

100 mm dia

150 mm dia

200 mm dia

Providing and fixing forged brass bail valve with forged brass ball (suitable for test pressure of not less than 15 kg / sq.cm of the following size:

25 mm dia

80 mm dia

150 mm dia

200 mm dia

100 mm dia

150 mm dia

200 mm dia

TOTAL

Chilled Water insulated pipe

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class ‘O’ insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect.

200 mm dia (32mm Thick Insulation)

150 mm dia (32mm Thick Insulation)

125 mm dia (32mm Thick Insulation)

100 mm dia (32mm Thick Insulation)

80 mm dia (32mm Thick Insulation)

40 mm dia (32mm Thick Insulation)

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified

125 mm dia

100 mm dia

80 mm dia

40 mm dia

40mm dia.

40 .mm dia

40 mm dia

DSR 2022(E&M) 16.12.1

Thickness 0.63 mm sheet

Thickness 0.80 mm sheet

Thickness 1.00 mm sheet

Thickness 1.25 mm sheet

Damper

Actuator

Fire Damper

Actuator

Thermal Insulation

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class “O”) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.

Acoustic Lining of Ducts

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications.

25 mm Dia

40 mm Dia

25 mm Dia