SPECIAL REPAIRS TO BLDG NO A 64 AT SALVAGE SUB DEPOT OF COD AGRA SPECIAL REPAIR OF CHAIN LINK FENCING WITH IRON POST IN FRONT OF 50 I PARA BDE SIG COY AND PROVN OF SHED IN TRG GROUND AT 50 I PARA BDE SIG COY OTM UNDER GE WEST AGRA

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise spcifically provided complete all as specified and directed.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc. but excluding ashlar facing, dressed stone work and pre-cast concrete articles complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping, clean and washing down with water to remove dust, etc. and brushing neat cement slurry with 3.00 kg of cement per sq. metre all as specified and directed.

Taking down cement or cement lime plaster of any discription skirting/dado etc remove completely on brick or stone walls/ ceilings etc, including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks old size, straight or curved on plan exc 6 M mean radius, built in CM 1:6 complete all as specified & directed

M & L cutting holes into or through brick wall built in cement mortar superficial area exc 150 Sqcm not exc 400 Sqcm and making good in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.

S&F mild steel joist, channel, angle or Tee sections fixed independently with out connecting plates etcof grade fe-410-0 & fe 310-0 complete all as specified and directed.

S&F 5.0 cm thick sand stone slabs in sun shades, chajjas, shelves, roof slabs etc n.exc. 2m in length duly machine cut all faces punched dressed on face and along exposed edges and set and pointed in CM 1:4 complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 on any faces of brick or concrete surfaces of walls & finishing the surface even and smooth complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 on brick or concrete surface with water proofing compound @ 200ml/50kg of bag of cement finished even & smooth complete all as specified and directed. Note : Water proofing compound will be measured and paid seperately under respective item of Sch ‘A’.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for coloured glazed ceramic tiles (Digital & designer Pattern) in vertical surface 350 x 250 x 7 mm / 450 x 350 x 7mm thick or suitable size duly approved set and jointed in neat cement slurry and pointed in white or colour cement to match tiles including 10mm thick rendering in CM 1:3 on brick wall complete all as specified and as directed .

M&L non skid ceramic joint free coloured tiles (1st quality/ premium quality) 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exc. 0.11 Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed or bedding layer of cment mortar (1:6) complete all as specified and directed.

M&L non skid ceramic joint free coloured tiles (1st quality/premium quality) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11Sqm but not exc. 0.18 Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed or bedding layer of cment mortar (1:6) complete all as specified and directed.

M&L for vitrified ceramic light or any shade tiles 10mm thick (square /rectangular), polished (Ist quality / Premium quality), area of each tiles not exc 0.36 Sqm in floors etc, laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, complete all as specified and directed

M&L PCC 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) as in plinth protection, 75 mm thick, laying in alternate ways finished even and fair without using extra cement all as specified including filled joint with bitumin mastic complete all as specified & as directed.

S & F in repairs 15 mm bore chromium plated fancy bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs 15 mm bore pillar taps copper alloy with capatan heads chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD" with long screwed shanks and fly nuts screwed for iron pipe complete all as specified & as directed.

M& L for Vitreous China urinals, bowl type (back to corner wall type), complete including providing and fixing plus, bedding urinal against wall in cement mortar 1:2 securing urinal to plus with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified & as directed.

S&F in repair 15 mm bore CP angle/Stop valves, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified & directed.

S&F in repairs stop valve long shank (Concealed) (external threaded) cast copper alloy chromium plated screwed down high pressure with crutch or butter fly handle screw both ends for iron pipe or for union bore of pipe 15mm, all as specified and directed.

S & F in repair 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified & directed.

Taking up or down 15mm bore steel tubing and connection complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connection complete all as specified and directed.

S&F 15mm bore steel water tubing, medium grade, galvanized including fittings and fixed to walls, ceilings, floors or laid in floors complete all as specified and directed.

S&F 20mm bore steel water tubing medium grade galvanized including fittings and fixed to walls, ceilings, floors or laid in floors complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth etc. brick walls complete all as specified and directed.

S&F in repairs white vitreous china European wash down water closet pan, fixing with bolts including connecting to 100mm bore CI ‘P’ or ‘S’ trap as with following accessories a. white PVC low level flushing cistern 10 ltrs capacity with inlet, float valve complete -01 b. Flush pipe - 01 c.PVC connection 600 mm long - 01 d.Plastic seat cover coloured - 01

S&F in repair rotational moulded polyethene water storage tank 1000 ltr capacity, three layered, hoisted and fixed in position with lid threaded and locking system complete all aas specified & as directed.

S&F 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20 mm dia (minimum weight - 210 gm) complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts, 600 mm long complete all as specified and directed.

S&F in repairs vitreous china wash basin white flat back size 550 x 400mm including waste pipe chain plug, brackets complete all as specified and directed.

S&F 32 mm dia PVC waste pipe non serated for wash basin / sinks 800mm long including CP waste coupling complete all as specified and directed.

S & F in repair tubular towel rail brass chromium plated 20 mm Dia with brackets type fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

S&F in repairs 75 mm dia of outlet CI floor trap, with grating including jointing to waste pipe in cement concrete 1:2:4, type B1(Using 20 mm graded stone aggregate) complete all as specified and directed.

S&F in repair 100 mm round PTMT grating with openable flap (Min weight 100 gms) all as sspecified & as directed.

S&F in repair sheet glass shelf assembly consisting of 5.50mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm but not exc 4 sqm each complete all as specified and directed.

M&L mild steel framed work as in doors (as in ckowkats) or gates of angle or other section with guest plates rail, brasses rail etc exculsive of steel sheeting or other covering hanging also fastening and fixing complete confirming to Gde Fe-290 including preparation of surfaces and applying shop coat of red oxide before fixing complete all as specified and directed.

S & F of factory made 35 mm thick flush shutters, board solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 150 mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F 250 mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixedcomplete all as specified and directed.

S&F 100 mm long medium weight, cold rolled mild steel butt hinges complete all as specified and directed.

S&F 100 mm long stainless steel hinges type B-12 complete all as specified and directed.

S&F 150 mm long aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 100mm long aluminium anodised hasp and staple, safety type including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F in repair Soild PVC door frame of size 50mm x 47mm made out of 5 mm plain coloured PVC sheet, reinforced with MS square tube supplying and fixing in opening as per specification and drawing.

S & F in repair Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame work made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour P.V.C‘ C’ channel having a PVC sheet strip 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and as gap inserts for top rail; and bottom rail paneling of plain, colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rail with suitable PVC sheets beading and jointed together with solvent cement S&F in frame at site as per specification.

S&F floor door stopper 150 mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified & as directed.

S & F of factory mild steel ventilators with top hung shutters including hinges, steel peg stay complete all as specified and directed.

S & F mild steel work in framed work such as grills, gratings, guard bars etc, with ends of bars shouldered and / or riveted, or forged into spikes, and similar work confirming to Fe 410 - O or Fe 310 - O complete all as specified & directed.

S & F stainless steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples complete all as specified and directed.

S&F in repairs mild steel PVC coated drapery rods, 25mm internal diameter including decorating type brackets and PVC curtain rings 8 Nos per RM including fixing arrangement with drilling holes in walls, brackets etc complete all as specified and directed.

S&F 3 mm thick figured glass, pin headed type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

M & L for preparation of old wooden surface of any discription not otherwise discribed over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of plastered or un-plastered surfaces of walls and applying three coats of white wash on wall complete all as specified and directed.

M&L for preparation of new plastered or un-plastered surfaces and applying two coats of cement base paint on wall over a coat of priming paint complete all as specified and directed.

M&L for preparation of new plastered or un-plastered surfaces and applying two coats of oil bound distemper over a coat of average 1mm thick Birla putty complete all as specified and directed.

M & L for preparation of new steel surface over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer including complete all as specified and directed.

S&F anodised aluminium frame for doors, windows, ventilators and partitions with powder coated (Thickness of powder coating not less than 50 Micron) one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, ISI marked complete all as specified & directed.

S&F door closer hydraulically regulated, designation No. 3, universal type, aluminium die-cast suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg ISI marked, complete all as specified & directed.

S&F 5.50 mm thick tinted sheet glass with necessary jointing cleats, glazing clips, rubber packing & anodised aluminium snap beading complete all as specified and directed. .

S&F 100 mm long Mortice latch with four levers (vertical type), aluminium body and fixed complete all as specified & directed.

M&L in repair 12mm thick veneered partcle board exterior grade faced with decorative veneer on both faces including fixing with rubber gasket complete all as specified & as directed.

S&F anodised aluminium door shutters, aluminium section weighing 0.55kg/m with powder coated (Thickness of powder coating not less than 50 Micron) including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified.

S&F anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m powder coated (Thickness of powder coating not less than 50 Micron) including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinge type B-21 100mm long (2 no.), suitable handle (1 no.) complete all as specified

Dismantling wall and ceiling boards (fibre, pulp, insulation etc or insulation boards/ slabs/ blankets any thickness including cover filletts all ass pecified & as directed.

Dismantling timber in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section in framed work complete all as specifed & as directed.

S & F GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre. size of grid 605 mm x 605mm complete all as specifeid & as directed.

S &F hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified.

S &F exposed metal frame ceiling with calcium silicate board 6 mm thick of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 x 600mm grid (frame work for ceiling shall be measured and paid separately) complete all as specified & as directed.

Dismentaling of Asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings complete all as specified & as directed.

M&L for 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls with L-type or J-type or cranked hook bolts complete all as specified & as directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground for fixing of new posts complete all as specified & as directed.

M&L PCC 1:3:6, type C2 (using 40mm graded crushed stone aggregate) in foundation, filling and mass concrete complete (Including PCC Toe Wall) complete all as specified & as directed.

Use & wate of formwork to sides and soffits of floor or roof beam, bem haunchings, girders, bressummers, lintels, cantilevers etc. complete all as specified & as directed.

S&F mild steel screw bolts (machine made) with hexagonal or square head and one end screwed or screwed both ends, each screwed ends to be fitted with washers and one hexagonal or square nut, exc. 5 cm long & diameter of neck 5 to 10mm complete all as specified and directed .

S&F MS galvanized chain link fencing including line wires, any mesh, size and type of standards, rails, straining bolts etc. including provision of binding wire complete all as specified and directed.

S&F in repair galvanized, 2 strand, steel barbed wire, 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails, straining bolts including securing or tying at crossing with and provision of galvanized MS wire staples or steel pins etc as specified. (each line wire to be measured). complete all as specified and directed

Supply only mild steel round bars confirming to Fe 290 Gde E-165 10mm dia as line rows for securing chain link fencing complete all as specified and directed Note: Cost of cutting to length, bent to shape required & binding with MS wire is included in the above rate

M&L preparation of new steel surfaces of any description, exceeding 10 cm width or girth and applying two coats of black bituminious paint over a coat of red oxide primer complete all as specified and directed .

Excavation in post holes (or similar holes) in any type if soil each n.exc 0.50 cum gettingout, returning filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25cm in any type of soil comlete all as specified & as directed.

S&F steel work in tubular trusses in ornamental shape, vertical stanchions / pipes, horizontal parlines including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 comlete all as specified & as directed.

S&F 8mm thick mild steel plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 490 (Gde E-165) comlete all as specified & as directed.

S&F pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws comlete all as specified & as directed.

Surface dressing n.exc 15 cm deep getting out in any type of soil comlete all as specified & as directed.

Removing excavated soil exc. 250m but n.exc 500m and depositing where directed comlete all as specified & as directed.

M&L for screed bed or bedding layer of mortar 15mm thick in CM 1:4 for laying floor finishes comlete all as specified & as directed.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in near cement slurry in floors with grey cement and pigment comlete all as specified & as directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, lamp holders, light fitting etc removing materials to store for keeping in safe custody for taking credit or reuse serviceable fittings/fixtures and making good the disturbed surfaces of wall/floors.

M&L for Point wiring in concealed conduit with 1.5 Sqmm PVC insulated flame retardent low smoke (FRLS) single core stranded copper conductor for one light/fan/bell point in and including PVC conduit 19/20 mm dia to be terminated in pressed steel terminal boxes with 3 mm thick bakelite sheet top cover including 1.5 sqmm PVC insulated "Flame Retardent Low Smoke"( FRLS)" single core stranded copper earth continuity conductor controlled by one switch and/or one regulator complete all as specified and directed. (Wiring shall be made as per colour code in IS for Phase, neutral and earth)

All as per item no 98 above but for One socket outlet 5/6 Amps on independent bd controlled by one switch.

All as per item no 98 above but for One socket outlet 5/6 Amps controlled by one switch on same board with other switches

All as per item No 98 here in before but one socket out let 15/16 Amps controlled by one switch on independent board and wiring with 2.5sqmm cable.

S&F switch piano flush type single pole , 5/6 Amps one way, 230 volts, all as specified & asdirected .

Supply and fixing switch bell push button single pole, 5/6 Amps, one way, 230Volts all as specified & as directed.

S&F switch piano flush type single pole, 15/16 Amps one way, 230 volts, all as specified & as directed .

S& F socket outlet 5/6 Amps flush type piano 5 pin 230 volts all as specified & as directed.

S&F socket outlet 15/16 Amps multipurpose 3 pin 230 V all as specified & as directed.

S&F ceiling rose surface bakelite 62.5 x 25 mm size 3 terminals all as specified & as directed.

Supply & Fixing lamp holder , insulated body ,with back plate suitable for batten fitting complete all as specified and directed.

Supply and fixing electronic steping up type ceiling fan regulator suitable to operate at 230 volts 50 Hz, AC supply all as directed.

S&F in replacement sheet metal enclosure with socket plug top, single pole and neutral enclosure with two pin and earth plug and socket complete with one No MCB, SP, 20 Amps, 230 Volts, 10KA 'C' series complete all as specified and directed.

Supply & fix in replacement surface/wall mounting LED batten 20 watt luminaire having Aluminium housing and integrated electronic driver with mounting accessories complete with lamp holders fixed to wall/ ceiling with fixing accessories and connecting up with & including twin twisted copper flexible wire of size 0.75 sqmm from ceiling rose to fittings complete all as specified & directed. Make:- Havells cat part No-LUMILINEPLUSBS20WLED865SPCSS or equivalent Model of Philips/Bajaj/CG as approved by GE.

Supply & fix in replacement, outdoor street light LED 30 watt luminaire white powder coated with extruded grey aluminium housing and robust construction with reflector cover pre anodised and flat white high transmission acrylic cover or toughened glass, natural white type with electronic driver, connector block etc with internally prewired fixed to building with and including 1.20M long bracket made out of 40mm dia light grade GI pipe bent to shape & providing clamps 2 Nos made out of 50 x 6 mm Flat iron/MS clamps & 12mm dia bolts, nuts & washers etc and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed. Make:- Havells cat part No- SL30WLED757SASYBOPC or equivalent as approved by GE.

Supply and fixing in replacement of electrical bell (Ding dong type) AC, 230 Volt complete all as specified & directed.

Taking down care fully sub main wiring / service connections of any size including batten/ conduit, and making good the disturbed surfaces of wall/ floor complete all as specified & directed.

M&L sub main wiring of two single core PVC insulated unsheathed stranded copper conductor cables of size 6 Sqmm, 1100 volts grade drawn through and including 20mm dia PVC concealed conduit of 1.2 mm wall thickness including all fixing accessories, and 2.5sqmm PVC insulated stranded copper conductor cable as earth wire(green colour) connected to earth dolly complete all as specified and directed. (Phase-Red, Neutral – black in colour of cable) Note:- Both running cables including earth wire shall be measured & paid for as single length.

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 2.5 sqmm drawn in and including PVC rigid conduit medium grade not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, stranded copper conductor cable of size 1.5 sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 2.5 sqmm cable & one run of 1.5 sqmm cable alongwith PVC conduit including its accessories shall be measured and paid one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles.

Taking down distribution boards any size any type including MCB TPN/SPN/SP etc and making good the disturbed surfaces.

S&F in replacement of unserviceable MCB DB sheet metal enclosure triple pole and neutral 415 V with 200 Amps standard bus bar of suitable size and common neutral link and earth bar all enclosed on standard steel sheet flush mounting type double door factory fabricate complete without MCB and with encosure blank plates for unused way suitable for 4 way flush in wall complete.

All as per item No 118 above but DB SPN 8 way double door

S & F in repairs MCB, 63 Amps, TPN, 415 volts, 10 KA rupturing capacity, 'C' series complete all as specified and directed.

S & F MCB 40 Amps SP, 240 Volt 'C' series complete all as specified and directed.

S & F MCB SPN 40 Amps 240 Volts, 'C' series complete all as specified and directed

S & F MCB 6 to 20 Amps SP, 240 Volt, 'C' series complete all as specified and directed.

M & L earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm size, buried directly in ground (earth pit not less than 2.25 M deep below normal ground level) with top edge of the plate not less than 1.5 M below normal ground level connected to and including galvanised steel earth lead wire of 4 mm dia, including 15 mm bore GI light grade protection pipe upto 1 Mtr above the floor level of the buildings where main switch, DB etc, situated, earth lead wire connected to the earth plate by means of GI bolts, nuts, washers and earth plate surrounded by 150 mm thick alternate layers of charcoal or cock dust mixed with common salt 20 mm bore medium grade GI watering pipe PCC pit in PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) cover of precast RCC 1:2:4 type B-1(using 20 mm graded stone aggregate) duly reinforced with 8 mm formed or twisted bars @ 100 mm c/c both ways, GI wire mesh, GI sheet funnel necessary excavation in soft/ Looose soil and deposited the surplus soil to a distance not exceeding 50 mtr away from starting point, all as per electrical plate no:3 of SSR part-1 .

Supply laying and testing cable XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 sqmm 4 core complete all as specified and directed.

Excavation in trenches in soft/loose soil n.exc 1.50M wide and not exc. 1.50M in depth for foundation etc or for shafts, wells, cess pits, manholes etc area n exc. 10 Sqm on plan and n. exc 1.5 in depth and getting out complete all as specified and directed.

Returning filling in soft / loose in trenches after laying pipes, construction of man holes etc including spreading, leveling and watering and well ramming in 25 cm thick layers complete all as specified and directed.

Removing excavated material (soil) to a distance not exceeding 1.5 m above the starting point complete all as specified and directed.

Supply & laying reinforced precast concrete cable cover, class LV, type-I, flat, size 250 mm x 150 mm x 40 mm for cable protection complete all as specified & dirrected.

M&L for sand cushioning dry, fine for cable cushioning 8 cm below the cable and 15 cm above duly punned down to 18 cm over all complete all as specified & directed.

M/s Pooran Singh and Company

C P Singh and Co

MNR ASSOCIATES