REPAIR/MAINTENANCE OF CHLORONOME PLANT, DOSING PUMP SET, SOLAR WATER HEATER OF DIFFERENT CAPACITY LT PANEL ASTRONOMICAL TIMER PANEL AND OTHER MISC WORKS UNDER GE (SOUTH) MAMUN

Supply only non return valve with back pressure regulator for Chlorine Gas

Supply only single measuring glass assembly with measuring glass.

Supply only spare measuring glass capacity 0 to 500gm/hr of chlorine gas.

Supply only rotometer control nut upper side or lower side.

Supply only gas cylinder connection with union nut.

Supply only inlet valve.

Supply only ejector with union nut.

Supply only back stop/back pressure valve

Supply only union nut.

Supply only full Vacuum regulator complete with gas filter, safety relief valve, flow meter with manual setting and residual pressure safety device and rotometer, measuring glass assembly suitable for vacuum connection PE Tubing D 8/12, complete all as specified and directed.

Supply only main set for diaphragm disc with diaphragm.

Supply only ejector nipple 3" to 8" long with PVC seat.

Supply only rubber kit and maint set for measuring glass tube of chloronome plant.

Supply only rubber kit and maint set for non-return valve of chloronome plant.

Supply only rubber kit and maint set for inlet valve of chloronome plant

Supply only rubber kit and maint set for vaccume regulator of chloronome plant.

Supply only PE (Polyethylene) tubing 8/12 mm.

Per Job

Supply only impeller gun metal/bronze.

Supply only pump shaft stainless steel.

Supply only impeller casing cast iron/ neck ring.

Description all as per srl item No. 199.00 here in before 16 Sqmm 2 core size.

Description all as per srl item No. 199.00 here in before but 16 Sqmm 4 core size.

OF CHLORONOME PLANT, DOSING PUMP SET, SOLAR WATER HEATER OF DIFFERENT CAPACITY LT PANEL ASTRONOMICAL TIMER PANEL AND OTHER MISC WORKS UNDER GE (SOUTH) MAMUN

Supply only discharge/suction case housing of cast iron.

S & F in repair motor starter consist contactor, relay on off switch SPP auto / manual mode, terminal plate and volt and Amp meter complete all as specified and directed.

S & F in repairs CPVC pipes outer 20mm bore SDR 11 & Plain CPVC SDR 11 fittings in trenches / fixed to wall complete all as specified and directed.

S & F in repair GI pipes 20mm bore medium grade with all fittings laid in trenches / fixed to wall complete all as specified and directed.

S & F in repair Gun Metal ball Valve 20 mm dia heavy duty ISI marked screwed both ends for fixing pipe complete all as specified and directed.

S & F in repair stainless steel or cast iron ball Valve 20 mm dia heavy duty ISI marked screwed both ends for fixing pipe complete all as specified and directed.

S & F in repair water pressure guage 0-200 PSI x 4" liquid filled with valve & connecting pipe etc complete all as specified and directed.

S & F in repair gas pressure gauge with valve & adopter etccomplete all as specified and directed.

Supply only, ball ceramic (liquid end)

Supply only ring seal viton (liquid end)

Supply only suction valve seat (liquid end)

Supply only discharge valve housing (liquid end)

Supply only anti syphon valve (liquid end)

Supply only special function valve (liquid end)

Supply only low level switch (liquid end)

Supply only diaphragm (liquid end)

Supply only foot valve assembly (liquid end)

Supply only head for dosing plant (liquid end)

Supply only white suction/ discharge PE tubing

Supply only PP ring (EPU drive end)

Supply only housing for dosing plant (EPU drive end)

Supply only Thermostat (EPU drive end)

Supply only Varistor (EPU drive end)

Supply only Disck 0.5 SQ inch (EPU drive end)

Supply only EPU Assembly (EPU drive end)

Supply only pulsar assembly with LLS (EPU drive end)

Supply only adjustable shaft (EPU drive end)

Supply only rotor assembly with bearing brackets & tolerance rings pumps

Supply only shaft and impeller for agitator motor (as per existing sample)

Supply only coil 250V 50Hz

Supply only agitator motor single phase flange mounted

Supply only chlorine powder dosing pump of capacity as per existing sample dosing pump

Supply only, single head feed rate control with shaft for DECRIN dosing pump set model 96NHQ51

Supply only pump head (ferrules 1/4" and duckbil included) for DECRIN dosing pump set model 96NHQ51

Supply only roller assembly for DECRIN dosing pump set

Supply only pump tube for DECRIN dosing pump set

S & F in repairs MCCB 4 Pole, 415 Volt, adjustable type, 125/160 Amps with breaking capacity 25 KA. Suitable to existing frame size sample complete all as specified & directed.

Supply only weighted suction line strainer 3/8" for DECRIN dosing pump set model 96NHQ51

Supply only Check valve duckbill only (Pk of 5) for DECRIN dosing pump set model 96NHQ51

Supply only connecting Nut 3/8" with adapter for DECRIN dosing pump set model 96NHQ51

M&L for disconnecting dosing plant of any model any capacity alongwith components, for repair/replacement of minor defective spares parts i.e. filter, ceramic ball, rubber/oil seal, PVC socket, drain cap, circlip, piston stroke knob, piston sleeves, liner and nut, bolt and washer, gear oil ,Rewinding of motors etc.as required at installation for smooth functiong of dosing plant and greasing, cleaning, washing/reassembling and testing of dosing plant after repair complete all as directed. Note: (i) Delay noticed in undertaking the repair, if any, the recovery shall be made @ Rs 500/- per day from contractor's dues, till completion of the job. (ii) All the repair work shall be carried out at the concern installation. If required the item shall be taken to workshop for repair work. Spare parts shall be replaced as per existing sample to suit the equipment for smooth functioning.

M&L dismantlimng all parts of 3 phase 415 volts electric motor of any type, make and capacity, cutting & removing existing burnt/short circuited winding wire complete and M & L for rewinding of 3 phase electric motor of 3/5 HP with super enamelled copper winding wire of same gauge including impregnated paper, sleevs, lathorised fibre glass, varnish and tape, etc complete all as specified and directed.

M&L for dismantling all parts of single/three phase electric motor of any type, make and capacity, cutting & removing existing burnt/short circuited winding wire complete and M & L for rewinding of single/three phase electric motor of 0.5/1 HP with super enamelled copper winding wire of same gauge including impregnated paper, sleevs, lathorised fibre glass, varnish and tape, etc complete all as specified and directed.

Supply of chlorine gas in empty cylinder of capacity rating 25 Kgs to 100 Kgs suitable for chlorination of drinking water including painting of cylinder as existing colour . The empty cylinder shall be issued on proper gate pass for filling of chlorine gas. Note : In case failure of gas cylinder valve and chlorine gas leakage then contractor shall be responsible for rectification of defects immediately till leakage is stopped at site as well as at cylinder store yard by use of all safety measures complete all as specified and directed.

Supply only all bearing of size 6202/6203.

Supply only, sodium hypo chloride solution of 12.5% strength in sealed container as per sample complete all as specified and directed.

Supply only gland nut/cup.

Supply only pump motor coupling cast iron with rubber.

All as per description of Srl item No 75 here in before but of 50 to 100 KVA capacity .

All as per description of Srl item No 75 here in before but of 15 to 40KVA capacity .

Supply only diesel filter (Primary and baby) element with O rings for 250 KVA capacity DG set

Supply only diesel filter (Primary and baby) element with O rings for 100/125/160 KVA capacity DG set

Supply only diesel filter (Primary and baby) element with O ringsfor 50/63/75 KVA capacity DG set

Supply only diesel filter element with O rings for 15/25/40 KVA capacity DG set

Supply only engine oil filter with O rings for 250 KVA capacity DG set

Supply only engine oil filter with O rings for 100/125/160 KVA capacity DG set

Supply only engine oil filter with O rings 50/63/75 KVA capacity DG set

Supply only engine oil filter with O rings 15/25/40 KVA capacity DG set

Supply only air filter element for 125/160/ 250 KVA capacity DG set

Supply only air filter element for 50 to 100 KVA capacity DG set

Supply only air filter element 15/25/40KVA capacity DG set

S & F in repairs fan belt suitable for 100 to 250 KVA capacity DG set (as per existing sample)

S & F in repairs fan belt suitable for 15 to 75 KVA capacity DG set (as per existing sample)

S & F in repairs radiator rubber hose pipe with clamp suitable for 100 to 250 KVA capacity DG set (as per existing sample)

S & F in repairs radiator ruber hose pipe with clamp suitable for 15 to 75 KVA capacity DG set (as per existing sample)

Supply and filling in sump/toping up multi grade engine oil.

Supply and filling coolent in DG set radiator

Supply and filling Electrolite of specific gravity in lead acid batteries of DG set

S & F in repairs battery brass terminal (as per existing sample)

S & F in repairs DG set battery lead PVC insulated multi stranded copper conductor (as per existing sample)

S & F in repairs fuel pipe of reqd length with end terminal for 40 to 250 KVA capacities DG set (as per existing sample)

M & L for disconnecting of radiator from 100 to 250 KVA DG set and transporting to authorized workshop, carry out repair i.e. cleaning, descaling with restore plus solution, removal of leakage, welding, brazing etc. and re-fixing it at site and testing after repair, complete all as directed.

M & L for disconnecting of radiator of 25 to 75 KVA DG set and transporting to authorized workshop to carry out repair i.e cleaning descaling with restore plus solution,removal of leakage, welding brazing etc. and re-fixing it at site and testing after repair complete all as directed.

S & F in repairs, DG Set fuel gauge of DG set cap upto 250 KVA as per existing size, complete all as specified and directed

S&F in repairs, DG Set controller digital with LED display for 250KVA,capacity along with all function of controller as per manufacture instructions or OEM sample/existing one complete all as specified and directed.

S&F in repairs radiator assembly as per existing size, type and suitable to fit for DG Set of capacity upto 250 KVA, complete all as specified and directed.

M & L for disconnecting of fuel tank from 25 to 75 KVA DG set and cleaning internally and externally by removing all the dust/sadiments etc including repair/replacement of fuel cap if required at site complete all as directed and specified.

S & F in repairs water pump for 40 to 250 KVA capacity DG set (as per existing sample) complete all as directed and specified.

S & F in repairs, fuel injector pipe set of suitable number and size as per existing sample complete for 40 to 250 KVA capacity DG set complete all as directed and specified.

S & F in repairs, oil pressure gauge for DG set of 250 KVA capacity as per existing sample complete all as directed and specified.

S & F in repairs tempreture pressure gauge for DG set of 250 KVA capacity as per existing sample complete all as directed and specified.

S & F in repairs DG set door lock as per existing sample complete all as directed and specified.

S & F in repairs DG set door glass as per existing sample complete all as directed and specified.

Supply only injection check valve 3/8" for DECRIN dosing pump set model 96NHQ51

S & F in repairs Ignition switch for DG set of 250 KVA capacity with key as per existing sample complete all as directed and specified.

M&L for overhauling 12/24 volts self starter including replacement of flywheel ring carbon bushes, bearing bushes, re-winding of armature and filled and warnishing complete all as directed

S & F in repairs AMF panel battery charger of DG set as per existing sample complete all as directed and specified.

S & F in repairs, battery charger 12/24 volt of any make and type with replacement of defective parts such as rectifier, voltage regulator, Diode plate, transformer, amp meter, voltmeter etc. complete all as specified and directed

M & L for preparation of old painted surfaces complete body of DG set upto 125 KVA for repainting with superior quality super enamelled paint of colour as per standard Engineering pratice for engine alternator base frame etc by spraying and including writing SM No/MES No all as specified and directed.

Disconnecting existing over heated or burnt cable terminal at existing panel and cutting out over heated / burnt portion of cable, stretching / opening cable to suitable required length from available rings and reconnecting cable in position properly with providing new lugs, tapes etc for cable size upto 95 sqmm complete all as specified & directed

S & F in repairs, volt meter 0 to 500 Amp 3 phase as per existing sample

S & F in repairs, 3 phase Ammeter for DG set of 250 KVA capacity as per existing sample rating.

S & F in repairs CT as per existing sample rating complete all as specified & directed

M & L for disconnecting of fuel tank from 100 to 250 KVA DG set and cleaning internally and externally by removing all the dust/sadiments etc including repair/replacement of fuel cap if required at site complete all as directed and specified.

S & F in repairs indication lamps LED type with showing red, yellow and green colours suitable for 240 Volts AC supply complete all as specified & directed.

S & F in repairs on load changeover switch 4 pole, 415 volts, 400 Amps complete all as specified & directed

S & F in repairs, on load changeover switch 4 pole, 415 volts, 160/200 Amps complete all as specified & directed

S & F in repairs on load changeover switch 4 pole, 415 volts, 100/125 Amps in Open execution complete all as specified & directed.

S & F in repairs, Contactor 3 pole, coil voltage 220/ 415 Volts, 50 Hz having current rating (AC3 ) of 40/50/70 Amps suitable for existing size and rating as per existing sample complete all as specified & directed.

S & F in repairs Contactor 3 pole, coil voltage 220/ 415 Volts, 50 Hz having current rating (AC3 ) of 110/140 Amps suitable for existing size and rating as per existing sample complete all as specified & directed.

S & F in repairs MCCB 4 Pole, 415 Volt, adjustable type, 63/100 Amps with breaking capacity 25 KA. Suitable to existing frame size as per sample complete all as specified & directed.

S & F in repairs MCCB 4 Pole, 415 Volt, adjustable type, 200/250 Amps with breaking capacity 25 KA. Suitable to existing frame size sample complete all as specified & directed

M & L for repair to the existing feeder pillar box / panel boards by replacing worn out/rusted portion of MS sheet with new part or portion, fabricated out of 2 mm thick MS sheet in position including making necessary adjustments and alignments to make the existing feeder pillar box / panel board body to required shape (s) and size (s) all as directed. Note :- (i) The panel board repaired shall be made totally enclosed, weather proof for installing incoming / outgoing MCCB / Switch fuses/ cable etc. complete all as directed (ii) The rates quoted by the contractor are deemed to be including necessary cutting, welding, leveling and jointing etc. as directed to match & accommodate with the existing feeder pillar box / panel board . (iii) The replaced portion shall be painted with two coat of synthetic enameled paint over a coat of red oxide primer. (iv) Area of MS sheet replaced shall be measured for payment purpose.

S & F in repairs, LT panel door lock chromium plated or as per existing sample.

S & F in repairs door hinge for DG set of 250 KVA capacity as per existing sample complete all as directed and specified.

M & L for replacement of aluminium bus bar of any size & shape including appropriate colour PVC sleeves.

M & L for earthing complete with Galvanized Steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 M below normal ground level, connected to and including GI iron strip of size 32x6 mm flat by means of GI bolts, nuts, and washers, protected by 40mm bore GI light grade ISI marked pipe upto and including test points. Earthing plate shall be surrounded by alternate layers 15cm thi

Pkt of 4

M & L for preparation

S&F in repairs GI earthing strip 32x6 mm complete all as specified and directed.

M&L for servicing /cleaning of solar water heater, complete i.e. Hot water Tank, Evacuated Tubes, Flat Plate tubes, SDR, UPVC Pipes, checking all working parts and removing of unservicable parts and installation new spares as required on site, comlpete all as specified and directed. NOTE:- Parts replaced shall be measured and paid seperately as supply only aganist the appropriate item.

Taking out the broken, rusted solar panels/solar tube frames with supporting angles of any size and M & L for mild steel work of grade Fe-290 (Grade E-165) in stand for solar panel, tank from angles, flats etc all as directed, framed brackets or angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles as necessar, gusset plates, riviting etc. complete all as specified and directed.

S&F in repairs, of 20mm dia CPVC pipes (Hot & Cold type) SDR 11 and Plain CPVC SDR 11 Fittings on walls/ceiling/trenches or laying in floors complete all as specified and directed.

S&F in repairs, of 25mm dia CPVC pipes (Hot & Cold type) SDR 11 and Plain CPVC SDR 11 Fittings on walls/ceiling/trenches or laying in floors, complete all as specified and directed.

Description all as per srl item No. 199.00 here in before but 10 Sqmm 4 core size.

S&F in repairs, of sub main wiring with 2 runs of PVC insulated but unsheathed multi stranded copper conductor FRLS cable 1100 volt grade of size 6 Sqmm and one run of 6 Sqmm single core PVC insulated but unsheathed multi stranded copper conductor FRLS cable 1100 volt grade as earth lead drawn through in and including non metallic PVC conduit of size 20 mm dia (external) with wall thickness not less than 1.8 mm, ISI marked concealed in wall including accessories like bends, tees junction boxes, etc fixed in wall or ceiling etc complete all as specified and directed. NOTE: Two runs of submain wiring cable alongwith one earth wire & conduit shall be counted as one unit.

S&F in repairs broken flat collector plates tinted glass of solar panel size 2025 mm (Length) x 1025 mm (width) with new one including lifting from floor to roof of the building by manually or mechanically is included in the coated rates, complete all as specified and directed.

S&F in repairs for Rubber flexible Hose pipe of inner dia upto 25mm as per existing heat resistance type suitable for Solar plant of different capacity with suitable clamps, nut and bolts, complete all as specified and directed.

S&F in repairs water heating elements of capacity 2.0/3.0 KW for solar water heater, complete all as specified and as directed.

S&F in repairs, of thermostat for solar water heater complete all as specified and directed.

Attending complaint by deploying skilled Electrician /Plumber and Helper for checking electric motor, startor, Solar water heater and washing machine cum hydro extrator, tumbler and make it functionable and serviceable. Note:- (i) If contractor fail to attend complaint and resolve on same day an amount of Rs 1000.00 per day shall be recovered as penalty by department. (ii) All materials required for attending the complain shall be measured and paid seperately, however T&P shall be included in rate quoted.

S&F in repairs lagging to hot water pipe of superior quality of foam insulation nitrile rubber of thickness not less than 20mm, duly covered with aluminium foil of not less than 0.2mm and binded with suitable size of wire/net as required on site, complete all as specified.

S&F in repairs PP-R Ball valves (brass insert) of size for 20mm dia CPVC pipes as per requirement of the site, complete all as specified and directed.

S&F in repairs PP-R Ball valves (brass insert) of size suitable for 25mm dia CPVC pipes as per requirement of the site, complete all as specified and directed.

S&F in repairs Rotational moulded polyethlene water storage tank of capacity 500 Litres, three layers (cylindrical vertical with closed top), hoisted and fixed in position including 25mm dia PVC ball valve, high pressure with polythene float complete all as specified in SSR Part-1, complete all as specified and directed.

S&F in repairs for 15mm bore bib tap with flange, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F in repairs factory made sheet enclosure for MCB DB SPN 2 way without bus bar 240 volts with single door, IP-43 protection duly fixed / concealed in wall complete and making good disturbed surfaces of wall floor etc including necessary connecting lugging with copper lugs pin / ring type complete all as specified & directed.

Supply only Calcium Hypo Chlorite 65 to 70% (calcium based granular) disinfectant for water treatment in sealed packing of 45 Kg HDPE jars to MES store yard complete all as specified in PS II clause 7 of CA and as directed. Note:- Contractors shall produce origional purchase vouches and test certificates of materials as specified.

S&F in repairs, MCB SPN, 240 Volts, from 32 to 40 Amps with repturing capacity 10 KA 'C' series complete all as specified and directed.

Supply only, Alums crystal as per sample complete all as specified and directed. Note for item No 71 to 74 : Engineer in charge shall take over the materials, enter in the register and Receipt Voucher to this effect shall be issued and entered in MB under respective items.

M&L for plain cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete/sunken floors, including demolation of existing PCC of any description, complete all as specified and directed.

Push button with push button element for washing machine of cap 30 Kgs as per sample, complete all as specified and directed.

DTC and TC each for washing machine of cap 30 Kgs as per sample, complete all as specified and directed.

Timer 0 to 60 min for washing machine of cap 30 Kgs as per sample, complete all as specified and directed.

Reversing timer for washing machine of cap 30 kgs, complete all as specified and directed.

Stainless steel plate complete for washing machine of cap 30 kgs as per sample, complete all as specifi

ed and directed.

Pressure switch suitable for 30 Kgs washing machine as per sample, complete all as specified and directed.

Toggle switch for washing machine 30 Kgs motor as per sample, complete all as specified and directed.

LS Contractor 3 pole 220 volts 32 Amps suitable for 30 Kgs washing machine as per simple, complete all as specified and directed.

Gland dori, fan belt and greasing etc for washing machine of cap 30 kgs as per sample, complete all as specified and directed.

Attending complaint by deploying electrician / plumber/ helper for repair to electric motor, startor, LT panel dosing pumps, DG Set & making functionable and serviceable. Note:- (i) If contractor fail to attend complaint and resolve on same day an amount of Rs 1000.00 per day shall be recovered as penalty by department. (ii) All materials required for attending the complain shall be paid by seperately, however T&P shall be included in rate quoted.

Each job

IBLAR sleeves for 30 Kgs washing machine as per sample, complete all as specified and directed.

M&L for General Servicing of washing machine Tumbler Dryer of capacity upto 30 KG by dismentalling all movable/Revolving mechanical parts such as (Nut, bolt, washer, gland, greasing for motor) servicing/checking of electronic mechanism all circuits, wiring, push button, controller, other electrical parts such as Heating Element, Thermostat, contactor, Relays, MCCB, MCB etc. and also including rewinding of motor with reassembling all parts after necessary servicing and replacement in case of unsv parts, testing machine upto 1 hr of working all as required and directed including replacement of following unservicable spare parts. NOTE:- (i) This Rate is Inclusive of rewinding of machine motors. (ii) Parts replaced shall be measured and paid separately as Supply only

Single phase preventer suitable for 25 Kgs Washing Machine Tumbler Dryer as per sample

Rubber seal and fan belt for 25 Kgs Washing Machine Tumbler Dryer as per sample

Strip heater for washing machine 25 Kgs Washing Machine Tumbler Dryer as per sample

Presser switch pipe suitable for 25 Kgs Washing machine Tumbler Dryer as per sample, complete all as specified and directed.

LS Contractor 3 pole 220 Volts 40 Amps suitable for 25 Kgs Dryer as per sample, complete all as specified and directed.

Relay 2.5 Amps to 8 amps for Dryer Machine Motor as per sample, complete all as specified and directed.

Stainless Steel Spring assy for 25 Kgs Laundry Machine and Dryer assy as per sample, complete all as specified and directed.

Door Open/Close sensor for Laundry Machine and Dryer of Capacity 25 Kgs as per sample, complete all as specified and directed.

S&F in repairs, Solar water Heater Tank of Cap 200 ltr of existing shape & size/ type for existing solar water heating system with 5 years of manufacturer warranty, complete all as specified and directed. Note : Contractor shall provide the gurrantee of the manufacturer alongewith his own gurrentee.

S&F of the following parts (Item No 176 to 184 ) to of Washing Machine Tumbler Dryer 25 Kgs- 04 Nos 3 phase 415 volts, 50 Hz AC complete and servicing, greasing and gland dori for Motors, and testing after completion of work, all as specified and directed.

Supply, fixing in repair of 150W LED Flood Light luminaire made up of Pressure Die Cast aluminum housing with black epoxy polyester powder coating for long life with excellent illumination and instant light with low temperatures (-10 degree to +50 degree) . The luminaire shall be complete available CCT 5700K, IP66 for Optical Compartment and Control Gear Compartment.The Optical compartment shall be covered with heat resistant toughened glass for safety.The LED Flood light should be top maintainable for easy maintenance. LED Flood Light shall use multiple LEDs to get sufficient light output from the luminaire. The LED Flood Light shall be of Integral type. The Input voltage range shall be 100V to 300V. The LED Driver shall be of isolated type with Constant Current Constant Voltage topology to ensure optimum driving of LEDs. The LED Flood Light shall have power factor more than 0.95 including testing after installation complete all as specified and directed.

Description all as per srl item NO 199.00 above but 95 Sqmm 3.5 core size.

MCB Four pole 63 Amps suitable for existing LT panel board to control of Dryer Machine of capacity 25 Kgs as per sample, complete all as specified and directed.

Supply & fixing in repairs 60 W LED street Light luminaire, made up of Pressure Die Cast aluminum housing IP 66 effeiceint protection with heat resistant toughned glass with indidual LED lenses complete with black epoxy polyester powder coating for long life with excellent illumination and instant light with low temperatures (-10 degree to +50 degree) . The luminaire shall be complete available CCT 6500K, IP66 for Optical Compartment and Control Gear Compartment.The Optical compartment shall be covered with heat resistant toughened glass for safety.The LED street light should be top maintainable for easy maintenance. LED street Light shall use multiple LEDs to get sufficient light output from the luminaire. The LED street Light shall be of Integral type. The Input voltage range shall be 100V to 300V. The LED Driver shall be of isolated type with Constant Current Constant Voltage topology to ensure optimum driving of LEDs. The LED street Light shall have power factor more than 0.95 including testing after installation complete all as specified and directed.

Supply & fixing in repairs 70/72 W LED street Light luminaire, shall be made up of Pressure Die Cast aluminum housing IP 66 effeiceint protection with heat resistant toughned glass with indidual LED lenses complete with black epoxy polyester powder coating for long life with excellent illumination and instant light with low temperatures (-10 degree to +50 degree) . The luminaire shall be complete available CCT 6500K, IP66 for Optical Compartment and Control Gear Compartment.The Optical compartment shall be covered with heat resistant toughened glass for safety.The LED street light should be top maintainable for easy maintenance. LED street Light shall use multiple LEDs to get sufficient light output from the luminaire. The LED street Light shall be of Integral type. The Input voltage range shall be 100V to 300V. The LED Driver shall be of isolated type with Constant Current Constant Voltage topology to ensure optimum driving of LEDs. The LED street Light shall have power factor more than 0.95 including testing after installation complete all as specified and directed.

S&F in repairs industrial switchgear busbar chambers of size 600x600x150 mm of cap 200 A, 6 way for LT cable any size including necessary PCC/Wall mounted work, cable gland, all as in repair complete all as specified and directed.

Supply and fix in repairs 3 core PVC insulated and sheathed copper conductor cable of size 1.5 sqmm drawn through the existing pole/GI pipe bracket complete all as specified and directed.

Supplying, jointing and connecting in repairs cable end termination joint kit, out door, heat shrinkable type for underground cable including jointing kits and labour complete for making joints suitable for aluminium conductor cable of size 25 sqmm to 50 Sqmm 3.5 core, 1100 volts grade cable including excavation and earth work complete all as specified and directed.

All as per Srl item No 143 here in before but for 500 to 1000 LPD solar system

Description all as per srl item No. 199.00 here in before but 25 Sqmm 4 core size.

Supplying, jointing and connectingin repairs cable end termination joint kit, out door, heat shrinkable type for underground cable including jointing kits and labour complete for making joints suitable for aluminium conductor cable of size 70 sqmm to 120 Sqmm 3.5 core, 1100 volts grade cable including excavation and earth work complete all as specified and directed.

S&F in repairs cable of size 10 sqmm, twin core multistranded 1100 volts grade heavy duty PVC insulated aluminiun conductor, served with inner sheathed of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1m apart including 4mm suspended with galavnised steel wire, complete all as specified and directed.

Note for srl item No 185 to 188 above (Contd...):- 11. The fittings shall have arrangement so that maintenance required, if any can be carried out from Top cover. 12. The defect liability period of LED lights shall be 05 years from the certified date of completion & the contractor shall replace/repair the defective fitting within 07 days after handing over for replacement. 13. A guarantee of 05 years shall be provided by contractor supported by OEM covering all parts of luminaire. Contractor shall deposit security on this account @ 5% of work done against these items otherwise the same shall be deducted from the dues payable to him in RAR/Final Bill.

M&L for general servicing of washing/ Laundary machine of capacity upto 30 KG by dismantalling all movable/revolving mechanical parts such as (Nut, bolt, washer, gland, greasing for motor) servicing / checking of electronic mechanism all circuits,wiring,push Button, controller, other electrical parts such as Heating element, thermostat, contactor, relays, MCCB, MCB etc. and rewinding of motor with reassembling all parts after necessary servicing and replacement in case of unsv parts, testing machine upto 1 hour of working all as required and directed including replacement of following unservicable spare parts, complete all as specified and directed. NOTE:- (i) This Rate is Inclusive of rewinding of machine motors. (ii) Parts such as heating element thermostate contactor, relays, MCCB etc. shall be measured and paid separately.

S&F in repairs electronic driver after taking down street light, ISI approved company made as per existing make and size for suitable for LED fittings of cap upto 45-90 watts any type and make, and refixing the same complete all as specified and directed.

S&F in replairs electronic driver of LED security light after taking down street light, ISI approved company made as per existing make and size suitable for LED fittings of cap more than 100 to 150 watts any type and make, and refixing the same complete all as specified and directed.

Supply & fix in repairs decorative post top lantern 40 watts 230 volts, 50 HZ, mushroom or oval shaped in sothing opal/ prismatic finish made up of polycarbonate, suitable for 40 watt LED, all accessories prewire.

Note for srl item No 51 to 57 above:- 1. Driver shall be potted anti-vibration types. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be provided. 3. CRI (Colour Rendering Index) of fixture shall be > 70. 4. CCT (Colour Co-related Temperature of fixture shall be 5700K + 300 K. 5. System Lumen Efficacy shall be > 100 Lm/W. 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. Lenses shall be Modular Type. 8. PCB used shall be MC PCB type. 9. CA No. shall be written on each fitting before installation. 10. The name of manufacturer to be embossed on the fitting.

S&F in repairs, of the following parts (against Item No-163 to 173) of Washing Machine cum hydro extractor of capacity 30 kgs- 04 Nos for servicing, greasing and gland packing for Motors and testing after completion of work all as specified and directed.

Excavation in trenches in any type of soil n exc 1.5 mtr in width and n. exc 1.5 mtr in depth and getting out all as required for laying of cables,Foundation filling of poles or stays complete all as specified and directed.

M&L for sand cushioning to under ground cables 8 cm thick before laying the cable and 15 cm, after laying of cable punning sand upto 18 cm thickness complete all as specified and directed. Note :- Only punned thickness of sand shall be measured and paid.

M&L for Sub class ‘B’ bricks old size laid dry flat over the cable abutting each other width of protection equal to length of brick all as required complete all as specified and directed.