REPAIR TO FENCING / COMPOUND WALL AND BUILDING FOR MES PUMP HOUSE AND SUB STATION REPAIR TO PATHWAY ROAD SIDE BERN HARDSTANDING AT SE FALLS UNDER GE SHILLONG

Amount

Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion, embedded in concrete and making good disturbed ground complete all as specified and directed.

Dismantling fencing wire mesh any type complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

Supply only chain link mild steel galvanised fencing of mesh size 75mm x 75mm (design of mesh shall be approved by GE) made of GI wire not less than 3 mm dia including line wires, to any type of standards, rails, straining bolts, etc including provision of binding wire complete all as specified and directed

Fixing only chain link mild steel galvanised fencing of any mesh and type to any type of standards, rails, straining bolts etc including provision of binding wire complete all as specified and directed

S&F in repair galvanised two strand steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails, straining bolts including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc. complete all as specified and directed (each line wire to be measured).

S&F 10 mm dia MS round bars of any length as in stiffener to chain link fencing fixed to fencing post complete all as specified and directed .

Excavation in post holes not exc. 0.5 cum, getting out returing, filling in and ramming earth and broken hard core/rubble mixed with earth with around the layers not exiding 25 cm each layers watering and removing surplus soil to a distance not exceeding 50 cm making good complete in soft/loose soil.

M&L for PCC (1:3:6), type C1 (using 20 mm graded stone aggregate) as in foundation filling and mass concrete including all necessary form work complete all as specified and directed.

S&F mild steel angle iron or other sections for post and struts in fencing, flat iron fillets (for securing wire mesh etc) to fencing post, cut to shape, drilled and countersunk for screw, including cutting tops to shape as directed, drilling holes, notching for wire, embedding in concrete and screwing etc. conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F MS screw bolt (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc. 5 cm and n. exc 10 cm long, diameter of neck 5 to 10 mm complete all as specified and directed.

S&F MS screw bolt (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc. 15 cm and n. exc 22.5 cm long, diameter of neck 12 mm complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section for fixing of sheets and similar works complete of Gde Fe-290(Gde E-165) all as specified and as directed

M&L for RCC foundations, including rafts, footings , plinth beams, bases for columns etc type nominal mix (1:1.5:3) (20 mm graded aggrgate) complete

M&L formwork to sides of foundations and like complete all as specified and directed

M&L for RCC columns etc type nominal mix (1:1.5:3) (20 mm graded aggrgate) complete

M&L formwork to sides of pillars, posts,struts,pirs , coloumns and like complete all as specified and directed

M&L for prepration of new steel surface of any description over 10cm in width or girth and applying two coat of synthetic enamel paint over one coat of red oxide/ zinc chrome primer complete all as specified and directed.

Excavation in trenches not exc 1.5m wide and not exc 1.50 in depth for column & wall Cum foundation and getting out in soft/loose soil.

Removing , excavated soil material exc 1.5Km and n.exc 5 KM deposited where directed at Cum a level n.exc 1.5,m from the starting point.

Returning filling in, including spreading, leveling, watering and well ramming in layers not Cum exc 250mm in soft/loose soil, completed all as specified and as directed.

Demolition of Brickwork/solid concrete block work built in Cement mortar complete

M&L for precast cement concrete (1:3:6) type C1 (using 20mm graded agg) solid block masonry exc 10cm in width or girth and setting in CM (1:6) complete all as specified and directed.

M&L for precast cement concrete (1:3:6) type C1 (Using 20mm graded agg) solid building blocks or slabs 10cm thick (with plain or interlocking joints) setting in CM 1:4 complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, precast cement concrete block walling in any position, built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L for walling random rubble uncoursed well bonded, bedded and solidly hearted built in CM (1:6) complete all as specified and directed.

All as per item no. 35 above but except stone using serviceables stones complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints as specified of random rubble walling uncoursed or brought upto courses in hammer dressing with maximum depression on face from straight edge held against the dressed surface n. exc. 40 mm of lime or sand stone complete all as specified and directed

M&L for precast cement concrete type C1 ( 1:3:6, using 20mm graded crushed stone aggregates) as in bond stones set in cement mortar 1:4 complete all as specified and as directed.

M&L for raised pointing to random rubble masonary uncoursed or brought upto courses in CM 1:4 complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in parapets, coping, benching, appex stone etc water trough and the like including weathering slightly rounding or chamferred angle and throating etc including necessary formwork complete as specified and directed.

M&L for Broken glass coping on top of walls in CM(1:3) including taking out unservicable glass coping and removial of rubis out of primeses from site complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for precast RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in cover slabs, shelves and similar articles set in CM (1:6) including necessary form work complete all as specified and directed.

M&L for Mild steel TMT deformed bars, 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed.

Taking down cement plaster including racking out joints, hacking for key scrubbing down with water etc including removal of rubbish material from site complete all as specified and as directed.

M&L for rendering 15mm thick in CM (1:4) in two coats (10mm and 5mm thick) mixed with water proofing compound with 5mm thick layer on fair faces of brick work or concrete surfaces including finishing the surface even and smooth without using extra cement, complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

Supply only for water proofing compound.

M&L for 10mm thick plaster in cm (1:6) on fair faces of brick or concrete surfaces including finishing even & smooth without using extra cement complete all as specified and directed

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two finishing coat of exterior emulsion paint, anti fungal resistance, dirt resistance exterior paint of required shade including over a coat of alkali resistant primer over a coat of 1mm wall care putty complete all as specified and directed.

M & L for preparation of newly surfaces and applying two coat of oil bound distemper with roller on wall etc complete all as specified and directed.

M & L for preparation of surfaces and applying one coat of oil bound distemper with roller on old treated surface of wall etc complete all as specified and directed.

M & L for preparation of old treated wood or wood based surface of any description exceeding 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for complete removal of existing treatment of wall and applying two coats of Oil bound distemper, over 1 mm thick wall care putty including necessary preparation of wall surfaces complete all as specified and as directed.

M&L for complete removal of existing old treament on wall and applying two coats of exterrior emulsion paint (Weather coat) over a coat of alkali resistant primer over a coat of 1mm wall care putty complete all as specified and directed.

Demolition of PCC (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L for PCC type B2 (1:2:4) (Using 40mm graded stone aggregate) in surface channels and drains etc. finishing surface even and smooth without using extra cement including form work complete.

M&L for extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

M & L PCC 1:4:8 type C2 (using 40 mm graded aggregate) as in Foundation filling and mass concrete.

M&L 75mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in plinth protection finished even and fair with 10 mm joint filled with bitumen mastic (mix of bitumen and sand at 3m intervals complete all as specified and directed.

M&L 100 mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate as in hard standing finished even and fair laid in alterrnate bays of size not exc 2 m X 2m with construction joints and filled with joint sealing compound complete all as specified and directed.

M&L for PCC 1:3:6 type C2 (using 40mm graded aggregate) 100mm thick as in sub base, paving etc finished even and fair complete all as specified and directed.

M&L for machine pressed pre polished cement concrete designer tiles 400 X 400 X 25mm thick over 15mm thick screed bed in CM 1:4 set & jointed in neat cement slurry & pointed in white or coloured cement to match as in floor complete all as specified. Make: Ultra and equivalent

M&L Machine pressed precast concrete polished interlocking paver block any shape and size of approved design confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade complete all as specified and directed.

M&L of sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area exc 1.5 sqm but n.exc 4 sqm each including make good and all as specified.

Taking down chowkhat with shutter (without taking off shutter from the frame) but n.exc 1.5 sqm each including make good and all as specified.

Taking down shutters of any description exc 1.0 sqm but n. exc 2.0 sqm each all as specified

Taking down shutters of any description but not exc 1 Sqm each all as specified.

S&F 2nd class hard wood plain, solid, straight chawkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints all as specified.

S&F 30mm thick flush shutter solid core construction with block board core and plywood face panels, decorative face veneer with lipping/frame to match on both sides .

S&F 35 mm thick 2nd class hard wood plain framed panneled shutter any number of panels with panel of 9mmB.W.P. commerical play flat on both side with feather edged all as specified and directed

M&L 30mm thick 2nd class hard wood factory made glazed and skeleton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood and wood based materials of any description not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer all as specified and as directed.

S&F factory made pre laminated solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with single piece extruded pvc profile both side prelam PVC sheet 'C' channel having a 5mm thick PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and 5mm thick both side prelam single piece extruded pvc profile for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of both side prelam 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and shown on drawing given in SSR Part II. The width of stiles & rails shall be in proportion to the width of the door shutter as given in SSR Part I.

S&F pre laminated solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam single piece extruded pvc profile and edgs will be painted to match with prelam sheet , PVC sheet are to be reinforced with 19x19mm MS square tube EPDM rubber gasket weather seal shall be provided through out the frame. The profile shall be mitre cut at two corners and joint by insrting 2 nos of 150mm long backets of 15mmx15mm MS square tube inside the 19mmx19mm MS square tube and suitably screwed and fixing in opening as per specification & drawing complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, size of hinges 100mm.

S&F Butt hinges, medium weight, cold rolled mild steel, size of hinges 75mm.

S&F Extruded Aluminium, anodised, bow handles of size 150mm.

S&F Extruded Aluminium, anodised, bow handles of size 100mm.

S&F aluminium anodised barrel bolts and fixed of 200 mm length

S&F aluminium anodised barrel bolts and fixed of 100 mm length

S&F Mild steel sliding door bolt, plate type stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, length of bolt 300mm.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frame including taking out old wooden beads complete all as specified and directed.

S&F 3 mm thick figured glass, pin head type and glazing with oil putty or wooden beads in squares n.exc 0.5 sqm in each pane complete all as specified and directed.

M&L for 3mm thick sheet glass ordinary quality and glazing with wooden beading wooden surfaces/putty on iron surfaces in square n exc 0.5 sqm in each pan.

Dismantling of timber scantling 40 sqcm and over in section in any position complete all as specified and directed.

Dismantling of timber scantling in fillets, rails, posts, rafters, purlins etc under 40 sqcm in section in any position complete all as specified and directed.

M&L 2nd class hard wood in scantling clean sawn timber fixed complete all as specified and directed.

Dismantling of wall/ceiling boards (fibre, pulp,insulation, etc.) or insulation boards/ slab/blankets, any thickness including cover fillets.

S&F Gl frame work for snapgrid false ceiling comprising of Gl perimeter channnel 0.55 mm thick with Main T- flange of 25 mm and web of 30 mm fixed to surrounding wall angle with flange and web 25 mm each , Cross T with flange 25 mm and web 25 mm fixed to main T, Main T is suspended from soffit @ 1200 mmm c/c using GI wire of 4mm thickness GI frame will be 60 x 60 cm to recieve E-board ceiling complete all as specified and as directed .

M&L for 4mm thick non asbestos fiber cement building boards 600x600 mm prepainted fibre boards ceiling designer/decorative type with different designs as approved by the Engr-in-charge fixed or laid in ceiling timber /GI/ aluminium frame work in ceiling flat or sloping complete all as per manufacturer instruction complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

M&L for Non skid light shade, joint free ceramic tiles, 7 to 8 mm thick square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour over 15mm thick screed bed in CM 1:6 complete all as specified and directed

M&L for Non skid joint free ceramic tiles, 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour over 10mm thick rendering in CM 1:4 complete all as specified and as directed

M&L for Glazed ceramic coloured tiles in vertical surface of size 450 x 350 x 7mm/350x250x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with the tile colour over 10mm thick rendering in CM 1:4 complete as specified and directed

M&L for outdoor coloured vitrified paving tiles, joint free(edge cut) of size 300x300x8 to 10mm thick as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in cement sand mortar 1:4 complete all as specified and as directed

M&L for outdoor coloured vitrified paving tiles, joint free(edge cut) of size 300x300x8 to 10mm thick as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement over 10mm thick rendering in CM 1:4 complete all as specified and as directed

Dismantling of plain or corrugated AC/ steel /fibre glass reinforced transluscent sheeting any guage thickness including nainital or similar pattern roof covering complete all as specified and directed.

S&F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed wih coach screwsand washers, in roofs, walls etc. With grade of zinc coating 120GSM complete all as specified and directed..

S&F 0.63mm thick galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and strainght flashings (length and girth as fixed) with grade of zinc coating 120GSM complete all as specified and directed..

S&F in repairs Vitreous China Urinal, Half stall type, white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; also including brass chromium plated waste coupling 32mm dia, and waste pipe with grating and union for discharge pipe complete all as specified and directed.

S&F in repair Urinal spreader of chroumium plated any for fixing with 15 mm dia pipe complete all as specified and directed.

S&F in repair vitreous china urinal partition white size 310 X 700 mm above floor, fixed to wall complete all as specified and directed.

S&F in repairs Vitreous China Wash Hand Basins, size 550 X 400 mm (Flat Back or Angle Back type) including 32mm dia Brass Chromium Plated Waste Fitting, waste pipe including Pair of Angle iron Brackets duly Painted/Erecting Stand including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed .Make:- Prayag /Hindware/Cera

S&F in repair Vitreous china squatting pan, 'Orissa' pattern, size 580 X 440 mm white, with integral foot rests including provision of lime concrete bedding, fixing of flushing cistern complete all as specified and directed.

S&F in repair PVC valveless, syphonic action type flushing cistern, low level, white, 10 Ltr capacity with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair Bip tap, chromium plated, 15mm fancy type,complete all as specified and directed.

S&F in repair Angular stop cock, fancy type, chromium plated, 15 mm bore complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repairs Brass Basin mixture CP mixer for mixing hot or cold water screwed down for iron pipe and fixed complete all as specified and directed Make: Parryware/Cera/Prayag

S & F in repairs tubular towel rail 600mm long, D type stainless steel complete all as specified and directed.

S&F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws

S&F cutting chases, pinning in concrete block work making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10cm girth.

Taking up or down steel tubing and connections for 15 mm bore of pipes

Taking up or down steel tubing and connectionfor 20 mm bore of pipes

S&F GI steel tubing medium grade 15mm bore with all fitting and fixed complete to wall and ceiling or laid under in floor

S&F GI tubes, medium grade galvanised, 20mm bore with all fitting and fixed complete to wall and ceilings or laid in floors

S&F in replacement of rotational moulded polyepolyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 1000 Ltrs incl dismantling of old unservicable water tank of any capacity all as specified and directed

S&F in repair float valve of size 20mm, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe all as specified and directed

S&F in repairs Gun metal gate valve class I (ISI) marked with iron wheel head, screwed both ends for iron pipe, suitable for following bore of pipe including taking down old existing unserviceable gate valve of dia 20 mm complete all as specified and directed by Engr-in-Charge

S&F in repairs PVC (SWR) 110 mm bore pipes single socketed in any length with rubber ring joints, fixed to walls/floor including necessary sockets, fitting and clamps for securing pipe complete all as specified and directed.

S&F in repair PVC (SWR) 75mm dia pipes single socketed in any length with rubber ring joints fixed to walls/floor including necessary sockets, fitting and clamps for securing pipe complete all as specified and directed.

S&F in repairs PVC (SWR) bend with access door of any radius 110mm bore complete all as specified and as directed.

S&F in repairs PVC (SWR) bend with access door of any radius 75 mm bore complete all as specified and as directed.

S&F in repair 75mm dia PVC (SWR) floor trap with CP grating including jointing with solvent cement to pipe complete all as specified and directed.

MS GIRI AND SONS

M/S U.K ENTERPRISE

M/S R.D. Electricals