Certain repairs to boundary wall, fencing, garbage bin and MES installation under AGE B/R-I, GE Gurdaspur.

Amount

Roughing the surface of old concrete floor picking sweeping clean and washing down with water to remove dust/mud etc.and brushing neat cement slurry @ 3kg/Sqm.

M&L for cement concrete 1:2:4 type B-0 using 12.50mm graded stone aggregate as in roof padding averaging thickness of 50 mm complete all as specified.

M&L APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) laid on applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m by forced application with butane torch over entire roof area with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in after cleaning surface complete all as specified and directed and all as per manufacturer's instructions.

S&F prepartion of new surface and applying two coats of aluminum paint on above of APP Membrane complete all as specified and directed.

M&L for removing existing pointing, raking out joints & flush pointing to bricks laid flat or brick tiles in pavings or brick tiles on roof with CM (1:3) including cleaning the surface grass, mud and like complete all as specified and directed.

M&L ceramic glazed coloured tiles of size 350x250x7mm/ 450x300x7mm thick joint free on and including 10mm thick screed bede in CM (1:4) set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles on vertical surfaces as in skirting/dado including demolition of existing tiles with screed complete all as specified and directed.

M&L non skid dark/ coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm to 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or coloured cement to match including 15 mm thick screed bed in CM 1:6 including demolition of existing tiles with screed complete all as specified and directed.

Taking down cement plaster any description on brick/ block/ stone walls, roof etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as directed.

M&L for rendering 15mm thick plaster in cement mortar 1:4 on brick or concrete surfaces of walls, finished surface even and fair upto ht. 12 mtr complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 12mm thick plaster in cement mortar 1:6 on brick or concrete surfaces of walls, finished surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 5mm thick plaster on ceiling in cement mortar 1:3 finished surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L preparation of new plaster surface and applying two coats of cement base paint on wall complete all as specified and directed.

M&L preparation of new plaster surface and applying two coats of oil bound distemper over a coat of primer.

M&L preparation of new plaster surface and applying three coats of colour wash on wall complete all as specified and directed.

M&L preparation of new plaster surface and applying three coats of white wash on ceiling complete all as specified and directed.

M&L for preparation of old plastered surface of walls rubbing down, making good holes, cracks, etc and stopping etc on existing surfaces and applying one coat of cement base paint on wall compete all as specified and directed.

M&L for preparation of old plastered surface of walls rubbing down, making good holes, cracks, etc and stopping etc on existing distempered surfaces and applying one coat of oil bound distemper on wall complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceiling by brooming down, making good holes, cracks, etc and applying one coat of white wash complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall by brooming down, making good holes, cracks, etc and applying two coats of colour wash height upto 12m complete all as specified and directed.

M&L for vitrified designer, exterior grade for parking etc. heavy duty tile of size 400mm x 400mm, 12mm thick, coloured, outdoor, set, jointed and pointed in neat cement slurry with white cement and pigment as in path/ floor, pattern of tile as approved by GE with 15mm thick in cement mortar 1:6 for laying floor finishing including demolition existing tiles with screed complete all as specified and directed. Make: Somany Durastone, Kajaria Duratech, Johnson Endura or equivalent of Nitco, Varmora as approved by GE.

M&L prepartion of old painted surface of wood & wood based surfces of any decsription not other wise described over 10cm width or girth and apply one coat of synthetic enamel paint complete all as specified and directed.

M&L prepartion of old painted surface of steel/iron based surfces of any decsription not other wise described over 10cm width or girth and apply one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old floor surfaces and applying one coat of floor emulsion paint/tile paint on chequard, interlocking or like of any description, of any colour as directed over 10cm girth or width, not otherwise described and provide glossy surface complete all as specified and directed. Make: Indigo

S&F steel window box type made of ERW tube, hollow P section of size 60mmX25mm double rebated outer frame comprising double skeleton shutters i.e. guaged & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 including one shop coat of priming and two coats of synthetic enamel paint and taking down old existing window complete:- (i) Thickness of the sheet shall be of 18 gauge (ii) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (iii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iv) MS Tower bolt 150mm long-02 Nos per leaf (v) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (vi) Cleat 55mm long of hollow square 15mmX12mm -01 Nos per leaf (vii) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (viii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). Note: Wire cloth, glass, shall be measured and paid for separately

S&F steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated) comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/TD-1019/08 Sh 1/3 to 3/3 including Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts, including one shop coat of priming and two coats of synthetic enamel paint including taking down old existing window/ ventilator complete all as specified and directed. Notes: (i) Thickness of the sheet shall be of 18 gauge. (ii) Glass/ wire mesh, shall be measured and paid for separately.

Dismantling of brick work, built in cement mortar or cement lime mortar including all quoins, pillars etc. complete all as directed.

M&L Brick work with sub class 'B' old size brick straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

All as per Srl item No 27 above but except bricks. (old serviceable bricks obtained from item No. 26 shall be used)

M&L for brick work with sub class "B" bricks (old size) straight or curved on plan to any radius in half brick thick wall as in sides of drain and upper band of drain with bricks laid on edge, built in CM 1:4 complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each complete all as specifiwd and directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each including hacking out of old broken glass panes from wooden or steel frame complete all as specified and directed.

Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter from the chowkats) complete all as specified and directed.

Taking down chowkats with shutter exc 1.50 Sqm but n exc 4.00 sqm each (without taking off shutter from the chowkats) complete all as specified and directed.

Taking down shutter of any description exc 1.00 Sqm but n.exc 2.00 Sqm each complete all as specified and directed.

Supply and fix for pressed steel frames of size 105 mm x 60 mm for doors with one or more rebates including necessary lugs, hinges, lock strike plate, as per ISI mark, including PCC (1:3:6), type C-0,( using 12.5 mm graded stone aggregates) as in filling of pressed steel frames including one shop coat of priming and two coats of synthetic enamel paint complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specification & drawing complete all as specified and directed.

S&F 30mm thick factory made solid PVC door shutter single side prelam PVC sheet used instead of plain colour PVC sheet and stile & rail having one side feathered edge on other side 10mm 90° bent edge PVC door shutter consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Paneling of plain colour PVC sheet to e fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, complete all as specified and directed.

S&F 30 mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels on both side Incl 6mm thick lipping/bidding fixed with nails on all sides complete all as specified and directed.

S&F 35mm thick second class hard wood (Hollock), glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, sizes of members of shutters as specified in SSR Part-I section 8 clause 8.24(a) supplied and fitted to chowkats complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F in repairs Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

M&L for preparation of new wooden surface exc 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

S&F Aluminium anodized barrel tower bolt of extruded section 150mm long complete all as specified and directed.

S&F aluminium alloy handle fabricated type anodized of size 150 mm long complete all as specified and directed.

S&F 100mm size butt hinges, extruded aluminium alloy, type B-21 with galvanised mild steel hinge pin, anodised and fixed with screws complete all as specified and as directed .

S&F Aluminium alloy, anodised, 250 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified and directed.

Material and Labour for repairing to RCC projections, chajjas, roofs, facia, ceiling etc. by scrapping, cutting, chiseling, de-rusting and cleaning exposed reinforcement of damaged loose RCC surfaces and applying neat cement slurry @ 3kg/sqm and filling the surfaces with cement sand mortar 1:3 or cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) using coarse sand in layers as required in patches area n.exc 5 Sqm each and thickness of RCC member exc 50mm including applying two coats of finishes to match with the existing surfaces at height upto 12m complete all as specified. Note:- Cost of formwork shall be deemed to be included in unit rate quoted by the Contractor.

M&L for pre cast cement concrete louvers and jali 1:2:4 type B-O (Using 12.5 mm graded aggregate) 25 mm thick set in cement plaster in CM (1:4) including taking down complete all as specified and directed by Engineer-in-Charge.

M&L cement concrete type D-2, 1:4:8 using 40mm stone aggregate as in sub base complete all as specified and directed (to raise level only).

M&L 60 mm thick PCC (M-35) factory made coloured interlocking tiles/ paver block of shape/ size as conforming to IS 15658, joints will be filled with fine sand, including dismantling existing tiles complete all as specified and as directed.

M&L sand filling under floors including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

M&L rubber moulded chequered cement concrete coloured tiles with glossy finish 30cm x 30cm x 25mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry with pigments in floors, including screed bed 15 mm thick in CM 1:6 complete including dismantling existing tiles and screed all as specified and directed.

Demolition of cement concrete in ground floor & paving n.exc 15cm below/ above ground level and of any description and in any position not otherwise specifically provided for.

Material and labour 75mm thick PCC (1:3:6) type C2 (using 40mm graded broken stone aggregate) as in plinth protection finishing the surface even and fair including cutting grooves 10mm x 30mm deep at every 3.0m interval and filled with mastic filling comprising 1 part of mastic bitumen and 3 parts of sand (all by weight) complete all as specified and as directed.

M&L for 40mm thick plain cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate), as in flooring finished even and smooth without using extra cement complete all as specified and directed.

M&L for cement concrete (1:2:4) type B-1, using 20mm graded stone aggregate as in coping, bands etc like including weathering, slightly rounded or chamfered throating as directed including form work (straight or curved) and finish all exposed surface of concrete complete all as specified and directed.

Taking down old galvanised, 2 strand steel barbed wire 2.24mm dia babed with barbs comple all as specifed and directed.

S&F for galvanized, 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing straining bolts, including securing and tying at crossing with and provision of galvanized mild steel wire, staples or steel pins etc. complete all as specified and directed. Note:- Each line of wire to be maesured separately.

Restraining and resecuring including making good staples etc. of old serviceable barbed wire in position.

Dismantling posts or struts (RCC) any section including taking out embedded portion and making good disturbed ground, embedded in natural ground, complete all as specified and directed.

M & L for PCC (1:3:6) type C-2 with using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

Excavation in post holes Soft/loose soil (or simila holes) each n. Exc 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixe with earth around in layers not exceeding 25 cm.

Removal of surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point and disposal.

Returning filling in the soft/loose soil including spreading, levelling, watering and well ramming in layer n.exc 25cm thick each layer complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts etc including provision of binding wire complete all as specified and directed.

Supply only 3 or 4mm dia PVC Coated galvanised mild steel chain link fencing of mesh size 75mm x 75mm fixed with string bolts complete all as specified and directed.

M&L for mild steel work of angles, flat iron as in post and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, embeding in concrete/foundation etc. conforming to Fe-290 Gde E-165 complete all as specified and directed by Engr-in-charge.

M&L for mild steel bolt factory made with hexagonal or square heads at one end and screwed the other, to be fitted with washer etc and one hexagonal or square nut, exc. 5cm and not exc. 10cm long and dia neck 10 to 12mm complete all specified and directed.

S&F Mild steel round bars conforming to Fe-290 Gde E-165, 10mm dia and over as in chain link fencing, fixed to concrete post with mild steel nuts, bolts and washers and tying to GI chain link fencing including hooking of ends for fixing between FI and nuts & bolts and welding wherever reqd ends complete all as specified and directed

M&L for preparaition of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer.

S&F rotational moulded polytheylene triple layered white water storage tanks of capacity 500 Litres ISI marked (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of existing water tank and ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule 20mm bore complete all as specified and directed.

S&F in repair stop cock 15mm bore cast copper alloy chromium plated with crutch or butterfly handle screwed down high pressure, screwed on both ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repair bib taps 15mm dia cast copper alloy chromium plated fancy type with capstan head screwed down screwed for iron pipe and fixed all as specified and directed. Make :- Prayag (Cat No 7506) or equivalent.

S&F in repair 15 mm angle valve cast copper alloy CP screwed down high pressure with crutch or butterfly handle, screwed on both ends for iron pipe complete all as specified and directed. Make :- Prayag (Cat No 7510) or equivalent.

S&F in repair pillar taps, cast copper alloy fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. Make :- Prayag (Cat No 7502) or equivalent.

S&F GI tubing 15mm bore medium grade, fixed to wall/ceiling or in floor etc with all fittings including taking up and down complete all as specified and directed.

S&F GI tubing 20mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings including taking up and down complete all as specified and directed.

S&F in repairs vitreous china wash down water closet (pedestal pattern) fixing with bolts, white, including stainless steel L-type jet spray with 1 m hose pipe, plastic water closet white closed pattern with flat bottom and cover with mild steel chromium plated hinging device and fixing bolts, connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all as specified and directed.

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with internal foot rest with PVC `P’ or `S’ trap, integral foot rest including connection to trap and flushing pipe etc and bedding in PCC 1:7:12 type F-2 complete all as specified and directed.

S&F in repair for vitreous china wash hand basin with full pedestal, white, size 550 mm x 400 mm flat back including brackets, chromium plated brass waste coupling and other fittings cutting for and pinning in ends of bracket or erecting stand complete all as specified and as directed.

S&F in repair vitreous china Urinal, half stall type minimum size 345x 320x 560mm, white (excluding flushing cistern) white with grating, waste coupling and union for discharge pipe complete including providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screw, pointing aroug urinal back in cement, grating and union for discharge pipe incl PTMT waste coupling, waste pipe, urinal spreader complete all as specified and directed.

S&F in repairs 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle, 32mm dia PVC flush pipe and connections, joints to pipes, making good the disturbed surfaces complete all as specified and as directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

Dismantling of cast iron ,PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches , if required.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall or in floor complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to walls or in floor complete all as specified.

S&F in repair PVC (SWR ) bends 110 mm bore any radius.

S&F in repair PVC (SWR ) bends 75 mm bore any radius.

S&F in repair Stack clamps (for 100 mm pipe) out of 20 mm by 1.5 mm flat galvanised iron and stays, including bolts and nuts and securing ends of stays to wall or roof.

S&F in repair Stack clamps (for 75 mm pipe) out of 20 mm by 1.5 mm flat galvanised iron and stays, including bolts and nuts and securing ends of stays to wall or roof.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as directed.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

S&F Pre-painted galvantume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick , ISI Marked of an colour having tensile strength of 550 Mpa as in roof covering/cladding to walls,fixed with self tapping screws as specified.

Dismantling framed work of timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed.

S&F of Rolled mild steel Gde Fe-410-W Gde E-250 Quality-A in Roof trusses (framed), trussed, purlins crane gantries, joist, channel, steel tube, rails & fastenings & heavy brackets framimg (Beam, tee, angle, Coulmn, Gusset Plates, channel, Hollow square/Rectangular or flat section) including distance pieces, cleats with riveted, bolted or welded attachment etc. complete all as specified and directed by Engr-In-Charge.

S&F of Rolled mild steel Gde Fe-410-W Gde E-250 Quality-A in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete complete all as specified and directed by Engr-In-Charge.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for upto 12 m ht. all as specified and directed.

Form work to rough finished surface of concrete flat to soffits of shelves, chajja, fins etc including supports over hangs

S&F 6mm dia and over upto 10 mm TMT bar cut to length bent to shape including cranking binding spirraly, hooping, hooking end and binding with MS wire (anealed) not less then 0.9 mm dia or securingwith clips as specified.

M&L for RCC 1:2:4 type B-1 (using 20mm graded stone agg) as in chajjas facia, shelves, slabs, bands etc and similar work all as specified.

A Schedule of Credit for old/unserviceable demolished/ dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

VOHRA CONSTRUCTION CO (BID ID -3079664)

M/S Harjinder Singh Contractor (BID ID -3079722)