8894 SPL REPAIRS TO CONVERSION OF OH LINE TO UG LINE, SECURITY LIGHT, LT PANEL AND LT ELECTRIC SUPPLY AND CHAIN LINK FENCING IN THE AREA OF EME, SAIBABA COMPLEX, ALC, MH(CTC) AND MINTSD UNDER GE SOUTH PUNE

Amount

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for taking out cable etc for repairs / laying cables/ foundation of pole / foundation of wall / column etc and getting out in following type of strata complete all as specified and as directed.

Soft/Loose soil

Hard Dense soil

Hard Rock

Excavation in trenches not exceeding 1.5 m wide and depth exceeding 1.5 m but not exceeding 3.0 m depth for laying cables, foundation for pole etc and getting out in soft/loose soil complete all as directed.

Returning, filling in including spreading, levelling, watering and well ramming in layer not exc. 25 cm complete all as specified and directed.

Returning filling in incluiding spreading levelling watering and well ramming in layers n.exc 25 cm (Rock) complete all as specified and directed.

Removing excavated material (soil) n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specifeid and directed.

Removing excavated material not exceeding 50 mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point (Rock)

M&L for laying of Reinforced concrete pipes,class NP2 with one collar per lengh of pipe of dia 100 mm ,2 nos half round ( for bottom and top) and laying under & over the cable complete all as specified and directed.

M&L for Reinforced concrete pipes,class NP2 with one collar per lengh of pipe of dia 120 mm ,half round (02 Nos for top & bottom) complete all as specified and as directed.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate for foundation of poles in foundation filling, mass concrete etc. complete all as specified and as directed.

M&L for PCC 1:2:4 type C-2 using 20 mm graded stone aggregate for coping of poles etc complete all as specified and as directed.

M & L for PCC 1:3:6 type C-1 (using 20 mm graded mechanically crushed stone aggregate) as in stays and coping of poles including necessary form work complete all as specified and directed.

Supply and laying cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor laid in trenches / floor / in wall of size 120 Sqmm 3.5 Core complete all as specified and as directed.

M&L for Earthing complete with GI earth plate electrode of size 60cm x 60cm x 6mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt fliing in alternate layers etc and connected to and including 32x6mm mm dia GI strip upto 7.5 mtr by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 15mm dia GI pipe connected to main control board and GI pipe medium grade 20mm bore for watering and including funnel, wire mesh, charcoal salt etc RCC pit cover flush to earth pit 50mm thick reinforced with 8mm TMT bar 100mmC/C and PCC chamber pit with PCC (1:3:6) type C1 (using 20mm graded aggregate) including excavation and earthwork disposal of surplus soil to distance not exceeding 50 metre) and testing after completion all as specified and shown on plate No 3 of SSR Part-I 2009

Supply,install,testing and commissioning of indoor distribution panel, dust / vermin proof, made out of 2 mm thick CRCA sheet with 400 Amp Tripple pole and Neutral Aluminium Busbar and internal connection with copper flexible wire with proper current rating including painting after seven tank process - RAL7032(powder coating paint) Protection-IP52 of suitable size factory assembled, front and back openable door, cubicle pattern, Modular and fully compartmentalised construction, floor mounted, with ISMC 75 all around with cable ally at top & bottom free standing type, with proper vantilation for naturally cooled 3 phase and nuetral 400 Amps current carrying capacity copper bus bars with exopy insulated coating with colour code, mounted on OMC/epoxy insulators and also alongwith copper earth bus bar of size 25 x 3 mm with terminal switches, after connecting bus bar connection/linkage and confirming to ISI 8623 and including the following:-

(i) MCCB 250Amp.4pole ,36KA with o/l ,s/c protection (Make- Legrand, ABB, Schneider,L&T) (ii) Extended rotary handle (Make- Legrand, ABB, Schneider, L&T) (iii) 250amp spreader terminals (Make- legrand,abb, Schneider, L&T) (iv) Phase indication lamp r/1,y/1,b/1 (Make- L&T) (v) Volt meter digital 0-500V, 96x96 (Make-L&T,Rishabh) (vi) Ampere meter 0-400A, 96x96 (Make- L&T) (vii) MCCB 4Pole 100 AMP=03 Nos with extended rotary handle (viii) MCCB 4Pole 63AMP=02 Nos with extended rotary handle. (MCCB with Thermal Magnetic Release Make- Legrand, ABB, Schneider, L&T) (ix) Current transformer 400/5 (Make- Kappa, AE (set of three)

M&L for replacement of outdoor type junction box made out of CRCA sheet 3mm powder coated comprising of epoxy coated aluminium busbar 400A - 04 Nos (3 Phase and 1 Neutral), mounted on iron frame made out of angle iron of size 40mmx40mmx5mm at 60 cm clear height from ground level complete with grouting of angle legs in PCC 1:2:4 all as specified and directed

Supply,installing, testing and commissioning of free standing weather proof, dust and vermin proof LT cubicle/ Modular construction fully compartmentalized panel out door type,with bus bar chamber and cable ally on both side, IP-54 and all as per IE rules fabricated with 3.0 mm CRCA double door type (Front side ; out side with main panel door and inside with compartmentlised door for each cubicle ) (Rear side main panel door and inside bolted door for each cubicle) Sheet for load bearing members and 2 mm thick for doors and covers and shall be powder coated with 7-tank process on all internal and external surfaces. the panel to be suitable for 1100 volt grade, 3 phase, 415 volts, 50 cycles AC supply. The panel shall be provided with MS angle iron frame 50x 50x 6 mm welded in shape and including necessary grouting in pcc 1:3:6 type C-1 with 20 mm grade stone aggregate completed with legs 30 cm in ground in pcc and 40 cm above ground including connecting to cable with cable gland, lugs etc”and comprising the following :

(a) 1200 Amps rated copper bus bar TPN duly insulated with coloured PVC sleeve as per standard colour code and rigidly mounted on bakelite/DMC insulator bus bar support (Square/round ) insulators of suitable size and good insulation resistance. (b) Air circuit breaker 800 amp 4 pole - 01 No (c) Changeover switch 600 Amps- 01 No (d) MCCB FP with extended RHOM control rup capacity 16 Ka at 415 Volt of capacity 315 Amps Icu=Ics = 100% -03 No Outgoing (e) MCCB FP with extended RHOM control rup capacity 16 Ka at 415 Volt of capacity 200 Amps Icu=Ics = 100% -03 No Outgoing (MCCB with thermal magnetic release Make- Legrand/Schneider/Siemens/L&T) (LT Panel- Manufactures those panels are type tested by CPRI, )

Supply, installing, testing and commissioning of Indoor type free standing floor mounted, dust and vermin proof LT cubicle/ Modular construction fully compartmentalized panel , IP-54 and all as per IE rules fabricated with 2.0 mm CRCA double door type Sheet for load bearing members and 1.6 mm thick for doors and covers and shall be powder coated with 7-tank process on all internal and external surfaces. the panel to be suitable for 1100 volt grade, 3 phase, 415 volts, 50 cycles AC supply. The panel shall be provided with Base channel of ISMC75 all around with cable ally at side and bottom cable ally min. 300 mm width at the bottom and bus bar chamber and comprising the following :

(a) 1200 Amps rated Aluminium bus bar TPN duly insulated with coloured PVC sleeve as per standard colour code and rigidly mounted on bakelite/DMC insulator bus bar support (Square/round ) insulators of suitable size and good insulation resistance. (b) Air circuit breaker 800 amp 4 pole - 01 No (c) MCCB 4 pole with extended RHOM control rup capacity 36 Ka at 415 volt of capacity 400 amps Icu=Ics = 100% - 02 No incoming (d) MCCB TP with extended RHOM control rup capacity 16 Ka at 415 Volt of capacity 200 Amps Icu=Ics = 100% -05 No Outgoing (MCCB with Thermal Magnetic Release Make- Legrand/Schneider/Siemens/L&T) (LT Panel- Manufactures those panels are type tested by CPRI)

Design, supply,install, test and comissioning of free standing floor mounted, dust and vermin proof Automatic power factor control panel 150 KVAR out door installation factory made both front and rear side double door system, fabricated with 3.15 mm thick CRCA sheet for load bearing members and 2 mm thick for doors and covers and shall be powder coated after 7 tank process. The panel shall consist of 400 ,Amps rating TPN bus bars of high conductivity aluminium alloy and shall be provided with colour coded heat shrinkaable sleeves,with more depth for accommodating Capacitor bank 10 Nos inside of the panel. Item No. 18.00 Contd.....

Item No. 18.00 Contd.... The panel shall be modular/cubical trype with bus chamber cable ally and provided with separate fully compartments for each switch including instrumentation such as Ampere Meter, Volt meter, Phase indicating lamp with double stud hinged door , front and rear openable with locking arrangement and suitable for 1100 Volts grade , 3 phase 415 Volts , 50 cycles , AC Supply and to with stand short circuit fault level of not less than 10 KA and degree of protection shall be IP 54 . The panel shall be fixed with angle iron frame made of angles of size 50x50x6 mm , embedded 200 mm below ground level in PCC 1:2:4, Type B1 using 20 mm grade stone aggregate , 600 mm above ground level and comprising the following including taking out of old panels etc , removing of cables and connecting to new panels with all required material such as glands, lugs etc Item No. 18.00 Contd.....

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70.0 sq mm 3.5 core complete all as specified and as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 300.0 sq mm 3.5 core complete all as specified and as directed.

Supply & lay GI tubing ''light grade'' for protection of cable and fixing to existing pole with new flat iron clamp 25x3 mm including nut bolts and washer etc complete or 1mtr of size 100 mm bore complete all as specified and as directed.

Supply, laying & testing cable XLPE insulated screened PVC bedded, galvanized steel wire armoured, electric power cables (heavy duty)with stranded aluminum conductor, 11000 volts ( Earthed) grade, of size 95 Sqmm 3 core complete all as specified and as directed.

Supply and fix new Gang operated air break switch 11kv, 200 Amps, triple pole, each pole consisting of galvanised steel base HT insulator as per BSS/ISS non-ferrous knife and spring loaded contacts, arching arms of adequate section to break magnetising current "TILTING TYPE" complete with square shaft of GI, adequate length for Phase separation, operating handle complete with locking arrangement in both "OFF" and "ON" position, with suitable clamp, nuts, bolts complete for fixing on the existing channel, making all electric connections / jumpers with bottle lugs commissioning and testing complete all as specified and as directed . (Make :- ATLAS, PACTIL, UNIVERSAL)

Supply and fix new drop out expulsion fuse HT 11 KV grade rating up to 100 Amps mounted on insulator and steel frame complete all heavy fuse barrel with fuse element complete set conforming to IS: 1818 as specified and as directed. (Make: ATLAS, PACTIL, UNIVERSAL)

Supply and fix lighting arrestor expulsion type complete with all fittings , transmission class discharge capacity 65 kiloamps suitable for 11000 volts complete all as specified and as directed. (Make: ATLAS, PACTIL, UNIVERSAL)

Supply and fix cable jointing kit for 11 KV grade cable for out door type termination cold shrink type joint complete with jointing material such as lugs etc and accessories suitable for 3 core XLPE armoured Al conductor cable of size 3 core 95 to 120 Sqmm complete all as specified and as directed. (Make :- Denson/M Seal/Siemens)

M&L for cross arm bracings, supports, clamps and back plates fabricated from structural steel sections including nut bolts , washers welding, bending cold or hot drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one coat of red oxide primer and two coats of aluminium paint complete all as specified and as directed.

Supply, install erect in trench vertical position steel tubular swaged welded poles complete with MS base plate of 6mm thick of size 450mm x 450mm final taper plug pole cap bolt nut and screwed, pole made out of ERW MS tubing confirming to IS 2713 Part II of 11.0 mtr long 410 SP-55 including drilling of holes of required size and nos for fixing of cross arms bracing support/ taking out of cables etc, with inbuilt junction box for 3 phase 4 wire AC supply and painting with one coat of red oxide primer and two coats of aluminium paint for exposed surface and two coat of black bituminious paint for the portion embeded in concerete complete all as specified and as directed.

M&L for cable route indicator made out of MS sheet duly marked with HT Cable 11000 volt and with MS angle embeded in PCC 1:4:8, 60 cm below ground level and 30 cm above Ground complete all as specified and as directed.

M&L for scrapping existing deteriorated old aluminium paint by brushing and painting of HT TWO pole structure by aluminium paint including cross arms, supports, angle, clamps and any other items complete all as specified and as directed.

All as per Item No 30.00 above but four pole structure complete all as specified and as directed.

All as per Item No 30.00 above but six pole structure complete all as specified and as directed.

M&L for Earthing complete with galvanised steel earth plate electrode 600 X 600 X 6.0 mm thick burried directly in ground [earth pit not less than 2.25 m deep below ground level] with top edge of plate not less than 1.50 m below normal ground level connected to GI earth strip 25x4 mm connected to the plate by means of GI bolts & nuts complete all as per Electrical plate No. 5 of SSR Part - I, connected to earthing test point including testing on completion including main earthing, charcoal, common salt, PCC 1:3:6, Type C-2 earth pit with RCC cover, MS funnel with GI watering pipe, GI Strip protection pipe 40 mm, wiremesh, earth work excavation etc complete all as specified and as directed. (Note :- GI earth strip with protection pipe will be measured beyond 7.50 mtr.)

M&L for main earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or burried in ground or drawn in conduit /pipe or fixed to pole or any other indicated situation for loop earthing etc of galvanised strip 25x4 mm complete all as specified and as directed.

M&L for HT bus bar for 2/4/6 pole structure made out of aluminium tube having outer dia 32 mm and 06 mm thick suitable for 22 KV/11KV complete with all suitable joints with S S nut bolts etc and colour sleeve as per colour code including aluminum strip 25x4 mm of required conductor etc taking down existing aluminium conductor complete all as specified and as directed.

Design, supply, install, test and commissioning of free standing floor mounted, dust and vermin proof LT cubical panel indoor type, fabricated with 2.0 mm thick CRCA MS Sheet for load bearing members and 1.6 mm thick for doors and covers and shall be powder coated after seven tank process. The panel shall consist of 600 Amps rating TPN bus bars of high conductivity aluminium alloy and shall be provided with colour coded heat shrinkable sleeves. The minimum depth of panel shall be 600 mm. Item No. 36.00 Contd.....

Item No. 36.00 Contd..... The panel shall be provided with separate compartments for each switch gear and measuring instruments, the panel shall include instrumentation such as Ampere meter, Volt meter, phase indicating lamps etc for incoming with double stud hinged door, front and rear openable with locking arrangement suitable for 1100 Volts grade, 415 Volts, 50 cycles, AC Supply and to with stand short circuit fault level of not less than 10KA and degree of protection shall be IP 54. The panel shall be fixed with angle iron frame made of angles of size 50 X 50 X 6mm, embedded 200 mm below ground level in PCC 1:2:4, Type B-1 using 20mm grade stone aggregate, 600 mm above ground level and comprising the following:

Item No. 36.00 Contd..... (a) MCCB 4 pole with extended RHOM control rup capacity 36 Ka at 415 volt of capacity 400 amps Icu=Ics = 100% - 01 No incoming (b) MCCB FP with extended RHOM control rup capacity 25 Ka at 415 Volt of capacity 160 Amps Icu=Ics = 100% -08 No Outgoing (c) MCCB TP with extended RHOM control rup capacity 16 Ka at 415 Volt of capacity 63 Amps Icu=Ics = 100% -05 No Outgoing (MCCB with thermal magnetic release Make- Legrand/Schneider/Siemens/L&T) (LT Panel- Manufactures those panels are type tested by CPRI)

Design, supply,install, test and comissioning of free standing floor mounted, dust and vermin proof Automatic power factor control panel 100 KVAR out door installation factory made both front and rear side double door system, fabricated with 3.15 mm thick CRCA sheet for load bearing members and 2 mm thick for doors and covers and shall be painted witrh epoxy powder paint by means of electro static gun after vigorous pre treatment comprising of cold phosphating process on all internal and external surfaces after due preparation of surfaces. The panel shall consist of 450 ,Amps rating TPN bus bars of high conductivity aluminium alloy and shall be provided with colour coded heat shrinkaable sleeves,with more depth for accomodating Capacitor bank 08 Nos inside of the panel. Item No. 37.00 Contd.....

Item No. 37.00 Contd..... The panel shall be modular/cubical trype with bus chamber cable allyand provided with separate fully compartments for each switch including instrumentation such as Ampere Meter, Volt meter, Phase indicating lamp with double stud hinged door , front and rear openable with locking arrangement and suitable for 1100 Volts grade , 3 phase 415 Volts , 50 cycles , AC Supply and to with stand short circuit fault level of not less than 10 KA and degree of protection shall be IP 54 . The panel shall be fixed with angle iron frame made of angles of size 50x50x6 mm , embedded 200 mm below ground level in PCC 1:2:4, Type B1 using 20 mm grade stone aggregate , 600 mm above ground level and comprising the following including taking out of old panels etc , removing of cables and connecting to new panels with all required material such as glands, lugs etc

Supply and fix polymer insulator disc type suitable for 11 KV with necessary fixing arrangements complete all as specified and as directed. (Make: ATLAS, PACTIL, UNIVERSAL)

Supply and fix polymer insulator pin type suitable for 11 KV with necessary fixing arrangementscomplete all as specified and as directed. (Make: ATLAS, PACTIL, UNIVERSAL)

M&L for disconnecting the existing HT cable of any rating and capacity from poles/structure and connecting the same to bus bar box for carrying out repairs to pole/structure, after repairs to pole/structure reconnecting the same cable on pole/structure complete all as specified and as directed.

M&L for Prunning / trimming the branches of trees if any along overhead line, 3 mtr on all side below/ above/ sides of overhead line and removing the same upto 3 mtr away each span not exceeding 45mtr complete all as specified and directed. (The above is to be ensured for the entire contract period by cutting/trimming of trees any number of times as required).

Taking down defective street/security light fittings from height upto 9 mtr of any capacity or wattage (70/150/250/400 HPMV/HPSV/Metal Halide or T5 lamp/1x36 watt T/L/1x36 watt CFL types fittings) ,LED fittingsfrom pole/bldg for repairs and refixing the same/other location ,defective accessories like PVC insulated sheathed copper conductor etc.or replacing fitting complete all as directed. NOTES : (a) Scope of work does not include the spares and it will be measured and paid for separately under respective items:- (b) Cost of the electronic drivers and Surge protection Device (SPD) will be paid for separately as supply only. (c) Scope of work includes for minor stores i.e. pvc insulation tapes, screws, insulation sleeves, nuts, bolts, washers and flexible cable 23/0.0076 (for internal wiring) etc as required at site.

Supply only LED outdoor driver suitable for out door type Street light fittings of wattage 45Watt all as specified and directed.

Supply only LED outdoor driver suitable for out door type Street light fittings of wattage upto 75 Watt all as specified and directed.

Supply only LED outdoor driver suitable for out door type Street light fittings of wattage 80- 100 Watt all as specified and directed.

Supply only LED outdoor driver suitable for out door type Street light fittings of wattage 120-150 Watt all as specified and directed.

Supply only Surge protection devices compatible with industrial & out door LED street light fittings upto rated power of 75Watt , 5KA all as specified and directed.

Supply only Surge protection devices compatible with industrial & out door LED street light fittings above rated power of 75Watt and upto 150W ,5KA all as specified and directed.

Supply and fixing in replacement for post top lanterns fitting 25 Watt pure polyester UV resistant powder coated die cast aluminium housing with PMMA clear diffuser for uniform illumination spun aluminium of LED 25 watt. Model : LP07-251-XXX-57-CL 20W of Wipro or equivalent model in Bajaj / Phillips.

Supply and fixing in replacement for path directional reflector with PC diffuser and extruded aluminium powder coated bollard to provide uniform illumination for pathwaysium of LED 25 watt. Model : Whistling Oyster LB12-880-XXX-65-08 of Wipro or equivalent complete all as specified and as directed.

Supply, fixing and testing LED IP 66 roadway luminaries 45 Watt with suitable size bracket high power LED as light source and electronic driver for 45 Watt LED efficacy 100 lumens/watt CCT 5700K,CRI>70 PF 0.95, IP66, IK 07 SP5KV interval & 10 KV,SPD external complete all as specified and directed. (Make: Cat Part No :LR02-501-XXX-7-G1 of Wipro or equivalent make in Bajaj/Phillips)

Supply, fixing and testing LED IP 66 roadway luminaries 60 Watt with suitable size bracket high power LED as light source and electronic driver for 60 Watt LED efficacy 100 lumens/watt CCT 5700K,CRI>70 PF 0.95, IP66, IK 07 SP5KV interval & 10 KV,SPD external complete all as specified and directed. (Make: Cat Part No :LR02-671-XXX-57-G2 of Wipro or of equivalent model in Bajaj/Phillips)

Supply, fixing and testing LED IP 66 roadway luminaries 70 Watt with suitable size bracket high power LED as light source and electronic driver for 70 Watt LED efficacy 100 lumens/watt CCT 5700K,CRI>70 PF 0.95,IP66,IK 07 SP5KV interval & 10 KV,SPD external, complete all as specified and directed. (Make: Cat Part No :LR02-781-XXX-57-G2 of Wipro or of equivalent model in Bajaj/Phillips)

Supply, fixing and testing LED IP 66 roadway luminaries 80 Watt with suitable size bracket high power LED as light source and electronic driver for 80 Watt LED efficacy 100 lumens/watt CCT 5700K,CRI>70 PF 0.95,IP66,IK 07 SP5KV interval & 10 KV,SPD external, complete all as specified and directed. (Make: Cat Part No :LR02-981-XXX-57-G2 of Wipro or of equivalent model in Bajaj/Phillips)

Supply, fixing and testing LED IP 66 roadway luminaries 90 Watt with suitable size bracket high power LED as light source and electronic driver for 90 Watt LED efficacy 100 lumens/watt CCT 5700K,CRI>70 PF 0.95,IP66,IK 07 SP5KV interval & 10 KV,SPD external, complete all as specified and directed. (Make: Cat Part No :LR02-102-XXX-57-G2 of Wipro or of equivalent model in Bajaj/Phillips)

Supply, fixing and testing LED IP 66 roadway luminaries 100 Watt with suitable size bracket high power LED as light source and electronic driver for 100 Watt LED efficacy 100 lumens/watt CCT 5700K,CRI>70 PF 0.95,IP66,IK 07 SP5KV interval & 10 KV,SPD external, complete all as specified and directed. (Make: Cat Part No :LR02-112-XXX-57-G2 of Wipro or of equivalent model in Bajaj/Phillips)

Supply, fixing and testing LED IP 66 roadway luminaries 120 Watt with suitable size bracket high power LED as light source and electronic driver for 120 Watt LED efficacy 100 lumens/watt CCT 5700K,CRI>70 PF 0.95,IP66,IK 07 SP5KV interval & 10 KV,SPD external, complete all as specified and directed. (Make: Cat Part No :LR02-132-XXX-57-G2 of Wipro or of equivalent model in Bajaj/Phillips)

S&F thermoplastic cable junction box with weather proof for out door installation IP 66/67 protection grade of two terminals suitable for cable entry 10 -25 sqmm of size 205x255x112mm including connector on DIN channel including necessary clamps for fixing arrangement complete all as specified and directed. (Make Hensel Cat No KF2525G)

Supply only PVC insulated sheathed wire 1.5 Sqmm ,3 single core with copper conductor of colour red,black and green for connection street light fittings from over head line/pole boxes complete all as specified and directed.

Material & Labour for fixing LED flood light luminaries of cap 120 watt ,240 volt,Pressure die cast housing with IP 65 protection, heat resistant toughtened clear glass with frame complete with accessories , pre wired up to a terminal block and mounting attachment conforming to Cat Part No :LF20-132-060-57-G2 of Wipro or equivalent in Bajaj/ Phillips complete all as specified and as directed.

Supply, fixing and testing energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP65 flood light 150Watt with high power leds as light source, suitable for highmast and general purpose lighting. including taking out old unserviceable one complete all as specified and directed. (Make: Cat Part No :LF20-192-060-57-G2 of Wipro or equivalent in Bajaj/ Phillips)

Supply & fixing in replacement of twin core flat 6 Sqmm size1100 volt grade heavy duty cable PVC insulated with aluminum solid conductor over all PVC sheathed complete all as specified and as directed.

Description all as per item No 62.00 above but 10 Sq mm size complete all as specified and as directed.

Supply & fixing Street light bracket made to shape out of GI pipe 40 mm bore light grade, 1.5 mtr length and fixed in replacement with MS Clamps, nuts, bolts and washers on pole (clamps, nut bolts to be measured and paid for separately) complete all as specified and as directed.

Stringing / stretching incl jointing in situ of each span not more than 45 Mtrs of two electric poles having 3 Nos of ACSR including GI earth continuity wire, with/ without guarding wires on electric poles of any size at different locations all as ordered manually or by telephonically means to the extent of permissible sag or tension by removing jumpers or bindings from insulators and making fresh binding with aluminium tapes after stringing complete all as specified and directed.

S&F in replacement steel water tube light grade of size 50 mm dia conforming to IS 1239 of 1990 for for protection of LT cable fixing on wall / trenches/pole etc including taking out the same as directed.

Dismantling insulator any type/ any size from LT poles complete all as specified and as directed.

Supply and fixing insulations pin type LT 1100 Volts grade porcelain vitreous white or brown including one galvanized mild steel spindle, two galvanized iron washers, iron nut, 100 mm height, 65 mm dia all as specified and directed.

Material & labour providing shackle type insulator LT 1100 volt grade porcelain vitreous white or brown including insulator bolts, nuts 12 mm dia, 75 mm height and 90 mm dia of insulator complete all as specified and directed.

S&F in repair MCB single pole & neutral 32/40 Amps 240 volts, 10 kA rupturing capacity providing in DB complete all as directed. (Make :- Legrand Cat No 4065 00 or equivalent model of make Siemens/Schnider)

S&F in repair MCB Tripple pole & neutral 63 Amps 415 volts, 10 kA rupturing capacity providing in DB complete all as specified and as directed. (Make :- Legrand Cat No 4087 02 or equivalent model of make Siemens/Schnider)

S&F in repair MCB single pole 6-32 Amps, 240 volts, 10 kA rupturing capacity pall complete all as specified and as directed. (Make :- Legrand Cat No 408590 to 408593 or equivalent model of make Siemens/Schnider)

Repair/maintenance of APFC Panel board upto 150 KVAR capacity with replacement of unservicable spare part/components modification of control wiring as required including flexible copper wire lugs complete all as directed (Note: New spares required shall be measured and paid seperately under respective items as supply only.)

Supply only APFC Relays fourteen stage, 240 Volts complete all as specified and as directed. (Make: L&T, Cat No-ETA or equivalent make of TATA Livert/Crompton Greaves/Siemens/Havells)

Supply only moulded CT 100/5 VA class-I rectangular shape complete all as specified and as directed.

Supply only moulded CT 125/5 VA class-I rectangular shape complete all as specified and as directed. (Make: Areva/Kappa/Pragati)

Supply only moulded CT 150/5 VA class-I rectangular shape complete all as specified and as directed. (Make : Areva / Kappa / Pragati)

Supply only moulded CT 200/5 VA class-I rectangular shape complete all as specified and as directed. (Make : Areva / Kappa / Pragati)

Supply only LED phase indicators red, yellow and blue 240 V AC complete all as specified and as directed.

Supply only capacitor operation indicators LED type red and green 240 V AC complete all as specified and as directed.

Supply only capacitor duty contactors-Type MO C 3 KVAR rating @ 440V, 3Phase, 50Hz complete all as specified and as directed.

Supply only capacitor duty contactors-Type MO C 5 KVAR rating @ 440V, 3Phase, 50Hz complete all as specified and as directed.

Supply only capacitor duty contactors-Type MO C 10 KVAR rating @ 440V, 3Phase, 50Hz complete all as specified and as directed.

Supply only capacitor duty contactors-Type MO C 15 KVAR rating @ 440V, 3Phase, 50Hz complete all as specified and as directed.

Supply only capacitor duty contactors-Type MO C 20 KVAR rating @ 440V, 3Phase, 50Hz complete all as specified and as directed.

Supply only Fuse holders and fuse bases suitable for cylindrical / DIN fuse links of rated current 32A complete all as specified and as directed.

Supply only cylinderical/DIN type HRC fuse 2A to 32 A complete all as specified and as directed.

Supply only Fuse holders and fuse bases suitable for cylindrical / DIN fuse links of rated current 63 A complete all as specified and as directed.

Supply only cylindrical/DIN type HRC fuse 63 A complete all as specified and as directed.

Supply only capacitor of 2 KVAR,MPP heavy duty, cylindrical type 440 volts, 3 phase ,50Hz, gas filled complete all as specified and as directed.

Supply only capacitor of 3 KVAR, MPP heavy duty, cylindrical type 440 volts, 3 phase ,50Hz ,gas filled complete all as specified and as directed.

Supply only capacitor of 5 KVAR, MPP heavy duty, cylindrical type 440 volts, 3 phase ,50Hz, gas filled complete all as specified and as directed.

Supply only capacitor of 10 KVAR, MPP heavy duty, cylindrical type 440 volts, 3 phase ,50Hz ,gas filled complete all as specified and as directed.

Supply only capacitor 15 KVAR,MPP heavy duty cylindrical type 440 volt ,3 phase ,50Hz, gas filled complete all as specified and as directed.

Supply only capacitor 20 KVAR ,MPP heavy duty cylindrical type 440 volt, 3 phase, 50Hz gas filled complete all as specified and as directed.

M&L for disconnecting, taking out under ground LT cable of length not more than 3 m and of size 10 sqmm to 25 sqmm including excavation, taking out bricks and relaying the old cable in loop and making connection with proper new thimbles in cut out boxes,Feeder pillar boxes, MCBs ,junction boxes etc including refilling of sand, relaying old bricks and returning, filling in soil complete all as specified and as directed.

S&F Spreader terminals suitable for end connections of MCCB 3Pole upto 100A (set of 6) complete all as specified and as directed.

S&F Spreader terminals suitable for MCCB 4 Pole upto 100A (set of 8 ) complete all as specified and as directed.

S&F panel ventilating fan 100mmx100mm square type 220V AC 50 Hz 0.1A and with limit switch synchronised with panel door complete all as specified and as directed.

S&F for replacement of analog street light timer switch for mannual switching ON/automatic/OFF daily with clock precision +/-5min complete all as specified and as directed.

S&F power contactors 2 pole 40A, Model: MNX 40-2P, complete with suitable NO/NC auxillary contact blocks complete all as specified and as directed.

S&F compact industrial batten suitable for single T-8 LED tube alongwith LED polycarbonate tube 20 Watt with built in driver with metal heat sink double sided connection conforming to CAT Part No. Batten model no ECO,DIJB12LT8-20 Make : Crompton ,LED Tube Model : ULTRON ,LT8-20-865-(2)

M&L for straight through (Heat shrinkable) suitable for LT UG cable 1.1 KV including excavation and cable connection on pole complete of following sizes :- (Make: M-seal/Dension or equiavalent Make)

16 to 35 Sqmm 3 1/2 Core

50 to 95 Sqmm 3 1/2 Core

120 to 185 Sqmm 3 1/2 Core

M&L for end termination joint (Heat shrinkable) suitable for LT UG cable 1.1 KV including excavation and cable connection on pole complete of 16 to 35 Sqmm 3- 1/2 Core size :- (Make : M-seal /Denson/3M or equiavalent Make)

S&F LED batten luminaire 20 watt in extruded aluminium housing with efficiency of 125 Lumens / watt complete all as specified and directed

Testing and fault locating of HT underground cable with the help of cable fault locating machine at site including removal of moisture content from cable all as directed. (Note :- The machine for locating of fault will be arranged by the contractor .The quoted rate is included for the fault locating machine. Necessary excavation , earthwork etc measured and paid separately under Sch 'A').

Testing and fault locating of LT underground cable with the help of cable fault locating machine at site including removal of moisture content from cable all as directed. (Note :- The machine for locating of fault will be arranged by the contractor. The quoted rate is included for the fault locating machine. Necessary excavation , earthwork etc measured and paid separately under Sch 'A').

Dismantling unserviceable steel poles/struts of any size and removing from site complete all as specified and as directed.

Supply, errecting & fixing in replacement in steel tubular pole swaged ,type 410 SP 31 in true vertical position, pole conforming to IS-1678 of 9Mtr long complete all as specified and as directed.

Taking up UG cable of size 16 sqmm 2/4 core to 50 sqmm 3.5 core from trenches as required complete all specified and as directed.

Supply and laying XLPE Insulated armoured heavy duty electric cables with aluminium conductor, 1100 volts grade, cross sectional area 16 sqmm 4 core complete all as specified and as directed.

Supply and laying XLPE Insulated armoured heavy duty electric cables with aluminium conductor, 1100 volts grade, cross sectional area 35 sqmm 3.5 core complete all as directed.

Supply and laying XLPE Insulated armoured heavy duty electric cables with aluminium conductor, 1100 volts grade, cross sectional area 50 sqmm 3.5 core complete all as directed.

Material & Labour painting of steel tubular poles 9 m high including cross arms, clamps, back plates etc in situ on with one under coat and one finishing coat with aluminum paint after cleaning /preparation of surfaces including making white and black strips 30 cm wide 5 Nos with two coats of synthetic enamel paint and marking of pole No , Feeder No .

Dismantling RCC or steel post any section including takingout embedded portion and making good distrubed ground complete all as specified and as directed.

Dismantling of mild steel work of any description not other wise provided for

Dismantling of fencing wire mesh barbed wire complete all as specified and as directed.

M&L for PCC 1:2:4 type B-2 (using 40mm graded stone aggreagate) as in foundations fillings and mass concrete complete all as specified and as directed.

M/L form work to fins and facias, sides of lintel bands fair finished surfaces complete all as specified and as directed.

M&L for 75mm thick hard core of guage n.exc 63 mm broken stone spread and levelled, watered and rammed to a true surface complete all as specified and as directed.

M & L for brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified & directed.

S & F MS angle iron posts and struts in fencing including cutting tops to shape as directed,drilling holes,notching for wire,bolting etc and similar works confirming Fe-410-0 or Fe-310-0 complete all as specified and as directed.

Supply & fixing MS flat iron for fixing of chain link fencing with nut - bolts as verticle complete all as specified and as directed.

Supply & fixing 8mm to 10mm dia MS round bar conforming to Fe-410 as in chainlink fencing complete all as specified and as directed.

Supply & fixing nut and bolts fitted with washer exc. 12 not exc. 20mm in dia complete all as specified and as directed.

M & L for preparation of new steel surfaces & applying two coats of synthetic enamel to steel surfaces of any description over 10 cm in width or girth not otherwise described, over a coat of red oxide primer complete all as specified and as directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on brick/concrete surfaces of wall surface to be finished even and smooth without using extra cement complete all as specified and as directed.

M & L for preparation of new plastered surfaces & applying two coats of cement base paint complete all as specified and as directed.

M&L for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and as directed. (Note :- Each line wire to be measured seperately)

Supply only chain link MS Galvanised fencing any size or type complete all as specified and as directed.

Fixing only chain link fencing including line wires any mesh. Size and type to any type of standards rails straining bolts etc including provision of binding wire complete all as specified and as directed.

Rama Electricals

M/S - KRUPA ELECTRICALS

CHAITANYA WINDWELL

REKHA ELECTRICALS