AR/SR/Anurakshan work of G and I Type Govt. Resi. Qtrs. in Sect. No. 23 under Jail-3 Sub Dn, PWD Bhopal

AR/SR/Anurakshan work of G and I Type Govt. Resi. Qtrs. in Sect. No. 23 under Jail-3 Sub Dn, PWD Bhopal

Please Enable Macros to View BoQ information

Bill of Quantities (BOQ)

Probable Amount of contract :

(Rs. in Figures) : Rs. 61.00 Lacs

(Rs in words) : Rupees

Time Alloved : 09 months

Transportation by manual labour including loading, unloading and stacking for lead up to 50 metre.

Lime, moorum, building rubbish

Earth

Manure or sludge

Excavated rock

Sand, stone aggregate below 40mm nominal size

Stone aggregate 40mm nominal size and above

Stone soling

Bricks

S.W. Pipes

100 mm dia

150 mm dia

200 mm dia

250 mm dia

300 mm dia

350 mm dia

400 mm dia

450 mm dia

500 mm dia

600 mm dia

R.C.C. pipes, Steel cylinder, R.C. pipes, C.I. pipes, and reinforced cement pipes

100 mm dia

125 mm dia

150 mm dia

200 mm dia

250 mm dia

300 mm dia

350 mm dia

400 mm dia

450 and 500 mm dia

600, 700, 750 and 800 mm dia

Lime, moorum, building rubbish

Earth

Manure or sludge

Excavated rock

Sand, stone aggregate below 40mm nominal size

Stone aggregate 40mm nominal size and above

Stone soling

Bricks

S.W. Pipes

100 mm dia

150 mm dia

200 mm dia

250 mm dia

300 mm dia

350 mm dia

400 mm dia

450 mm dia

500 mm dia

600 mm dia

R.C.C. pipes, Steel cylinder, R.C. pipes, C.I. pipes, and unreinforced cement pipes

100 mm dia

125 mm dia

150 mm dia

200 mm dia

250 mm dia

300 mm dia

350 mm dia

400 mm dia

450 and 500 mm dia

600, 700, 750 and 800 mm dia

beyond 30 cm girth up to and including 60 cm girth

beyond 60 cm girth up to and including 120 cm girth

beyond 120 cm girth up to and including 240 cm girth

above 240 cm girth

Ordinary rock

Hard rock (requiring blasting)

Hard rock (blasting prohibited)

Ordinary rock

Hard rock (requiring blasting)

Hard rock (blasting prohibited)

Pipes, cables etc., not exceeding 80 mm dia.

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm.

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item for depth up to 1.5 metre).

Extra for excavating trenches for pipes, cables, etc., in all kinds of soil for depth exceeding 3 m in depth, but not exceeding 4.5 m. (Rate is over corresponding basic item for depth up to 1.5 metre.)

Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, depth up to 1.5 m including including consolidating each deposited layers by ramming, watering etc. stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50m :

Ordinary rock :

Pipes, cables etc. not exceeding 80 mm dia.

Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia.

Pipes, cables exceeding 300 mm dia but not exceeding 600mm dia

Hard rock (requiring blasting)

Pipes, cables etc. not exceeding 80 mm dia.

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

Pipes, cables etc. exceeding 300 mm dia but not exceeding 600mm dia

Hard rock (blasting prohibited)

Pipes, cables etc. not exceeding 80 mm dia.

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

Pipes, cables etc. exceeding 300 mm dia but not exceeding 600mm dia.

Extra for excavating trenches for pipes, cables, etc. in ordinary/hard rock exceeding 1.5 m in depth but not exceeding 3 m. (Rate is over corresponding basic item for depth up to 1.5 metre.)

Extra for excavating trenches for pipes, cables, etc. in ordinary/hard rock exceeding 3m in depth but not exceeding 4.5 m. (Rate is over corresponding basic item for depth up to 1.5 metre.)

Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete. (Measurements to be taken of the face area timbered).

Depth not exceeding 1.5 m.

Depth exceeding 1.5 m but not exceeding 3 m.

Depth exceeding 3 m but not exceeding 4.5 m.

Close timbering in case of shafts, wells, cesspits, manholes and the like including strutting, shoring and packing cavities (wherever required) etc. complete. (Measurements to be taken of the face area timbered).

Depth not exceeding 1.5 m.

Depth exceeding 1.5 m but not exceeding 3 m.

Depth exceeding 3 m but not exceeding 4.5 m.

Close timbering over areas including strutting, shoring and packing, cavities (wherever required) etc. complete. (Measurements to be taken of the face area timbered) :

Depth not exceeding 1.5 m.

Depth exceeding 1.5 m but not exceeding 3 m.

Depth exceeding 3 m but not exceeding 4.5 m.

Extra for planking, strutting and packing materials for cavities (in close timbering) if required to be left permanently in position. (Face area of timber permanently left to be measured).

Extra rates for quantities of works, executed:

In or under water and/or liquid mud, including pumping out water as required.

In or under foul position, including pumping out water as required. Note: - The extra percentage rate is applicable in respect of each item but limited to quantity executed in difficult conditions. The depth shall be reckoned correct to 0.1 metre. 0.05 metre or more shall be taken as 0.1 metre and less than 0.05 metre ignored.

Filling available excavated earth (excluding hard rock/Ordinary rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Extra for every additional lift of 1.5 m or part thereof in excavation. (No extra lift is payable if work is done by mechanical means)

All kinds of soil.

Ordinary or hard rock.

Supplying and filling in plinth with crusher stone dust / coarse sand under floors including, watering, ramming and compacting in layers not exceeding 20cm in depth and dressing complete Note: - Maximum thickness of this layer shall be 20 cm.

Supplying and filling in plinth under floors including watering ramming consolidating in layers not exceeding 20cm in depth and dressing complete.

With hard muram having CBR >12 % at under floors including watering, ramming and compacting (minimum compaction 95% of MDD) in layers not exceeding 20cm in thickness and dressing complete. (Note:- maximum thickness of this layer to be provided shall be 30cm)

Supplying and filing in plinth with soil (other then BC soil ) having MDD not less than 1.85 t/m3 under floors including watering, ramming and compacting (minimum compaction 95% of MDD) in layers not exceeding 15cm depth and dressing complete.

Excavating holes more than 0.10 cum & upto 0.5 cum including getting out the excavated soil, then refiling the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering etc., disposing of surplus excavated soil; as directed within a lead of 50 m and lift upto 1.5m.

All kinds of soil.

Ordinary rock

Hard rock (requiring blasting)

Hard rock (blasting prohibited)

Supplying chemical emulsion in sealed containers including delivery as specified. (Chlorpyriphos/ Lindane emulsifiable concentrate of 20%)

Diluting and injecting chemical emulsion for POST- CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :

Along external wall where the apron is not provided using chemical emulsion @ 7.5 liters / sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall and rodding etc. complete, with Chlorpyriphos/ Lindane E.C. 20% with 1% concentration.

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diametre holes and plugging with cement mortar 1 :2 (1 cement : 2 sand) to match the existing floor, With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration.

Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling 10mm dia and 200mm deep holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 sand) to the full depth of the hole, with Chlorpyriphos/ Lindane E.C. 20% with 1% concentration.

Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same.

Deduct for disposed soil not levelled and neatly dressed.

Preconstruction antitermite treatment to the building under construction by providing.Stage 1: Treatment should not be carried out when it is raining or when soil is wet with rain or subsoil water. This also applies to fill up soil within the plinth area before laying the subgrade for flooring.

Making bore holes for providing dowel bars at designed depth in rock foundation by drilling 40 mm dia bore hole in rock including necessary bending hooking, in position and grouting with cement slurry etc. complete as per drawing and specification. (Steel to be paid separately).

Excavation in soil using hydraulic excavator and including cutting and loading in tippers, trimming bottom and side slopes in accordance with requirements of lines, grades and cross- section, and transporting to the appropriate ground contour, location and levelling and dressing earth neatly with all lifts and lead upto 1000 metre.

Earth work in rough excavation by any means and banking\filling excavated earth in layers not exceeding 20cm in depth, breaking clods, watering rolling each layer with 1/2 tonne in embankments for roads, flood banks, marginal bank and guide bank of filling up ground depression within campus, lead upto 50m and all lift. All kinds of soil.

Banking\filling excavated earth in layers not exceeding 20cm in depth, breaking clods, watering rolling each layer with 1/2 tonne roller or wooden or steel rammers etc. and rolling every 3rd and top-must layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal bank and guide bank etc. lead upto 50m and lift upto 1.5m. All kinds of soil.

Deduct for not rolling with power roller of minimum 8 tonnes for banking\filling excavated earth in layers not exceeding 20cm in depth.

Deduct for not watering with the excavated earth for banking\filling

Providing and laying of permanent piping technology anti-termite treatment before flooring work by installing LLDP (Low linear density polyethylene) tube of 8 mm O.D. & 6.4 mm I.D.with inbuilt pressure compensation chip at every 30 cm interval in the tube,. The contractor shall submit approved line plan for piping system and junction boxes dully approved by Engineer-in- charge with bond of 5 year warranty.

Permanent piping system with Junction boxes

Anti-termite chemical injected area

Ploughing the existing ground to a depth of 15 cm to 25 cm and watering the same. (All kinds of soil)

Cement mortar 1:5 (1 cement: 5 marble dust).

White cement mortar 1:3 (1 white cement: 3 marble dust).

White cement mortar 1:5 (1 white cement: 5 marble dust).

Mortar in lime , surkhi (50% red and 50% light yellow) and marble dust 1:1.5:0.5

With 20mm nominal size graded stone aggregate.

M-25 – Grade concrete

M-20 – Grade concrete

M-15 – Grade concrete

M-10Nominal (Mix-1 Cement : 3 sand : 6 graded stone aggregate )

With 40mm nominal size graded stone aggregate.

M-15 - Grade concrete

M-10 Nominal (Mix -1 Cement : 3 sand : 6 graded stone aggregate)

M-7.5 Nominal Mix -1 Cement : 4 sand : 8 graded stone aggregate

With fly ash.

1:2:3½:9 (1 ordinary Portland cement : 2 Fly ash : 3½ sand: 9 graded stone aggregate 40 mm nominal size)

1:2½:4:11 (1 ordinary Portland cement : 2½ fly ash : 4 sand : 11 graded stone aggregate 40 mm nominal size) Note: No fly ash is to be added to Portland Pozzolona cement in any case which itself contains fly ash.

With 20mm nominal size graded stone aggregate

M-25 – Grade concrete

M 20 – Grade concrete

M 15 – Grade concrete

M-10 Nominal Mix -1 Cement : 3 sand : 6 graded stone aggregate

With 40mm nominal size graded stone aggregate

M-15 - Grade concrete

M-10 Nominal Mix -1 Cement : 3 sand : 6 graded stone aggregate

Upto plinth: Foundations, footings, bases for columns, plinth beams, curtain walls, columns below plinth.

above plinth: Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, and string courses fillets etc.

Above plinth: Columns, pillars, posts and struts.

M-15 (With 20mm nominal size graded stone aggregate)

M-10 (With 20mm nominal size graded stone aggregate) Nominal Mix -1 Cement : 3 sand : 6 graded stone aggregate

M-25 (With 20mm nominal size graded stone aggregate)

M-20 (With 20mm nominal size graded stone aggregate)

M-15 (With 20mm nominal size graded stone aggregate)

M-10 (With 20mm nominal size graded stone aggregate) Nominal Mix -1 Cement: 3 sand: 6 graded stone aggregate.

M-15 (With 20mm nominal size graded stone aggregate)

M-10 (M 10) (With 20mm nominal size graded stone aggregate) Nominal Mix -1 Cement : 3 sand : 6 graded stone aggregate

M-15 (With 20mm nominal size graded stone aggregate)

M-10 (With 20mm nominal size graded stone aggregate) Nominal Mix -1 Cement: 3 sand: 6 graded stone aggregate.

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement: 2 sand: 4 graded stone aggregate 12.5mm nominal size).

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size).

Extra for providing and mixing water proofing material as per IS standard in cement concrete work quantity as prescribed by the manufacturer.

Applying a coat of residual petroleum bitumen of penetration 80/100 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Extra for concrete work in superstructure above floor two level for each floors or part thereof

Extra for laying concrete in or under water and/or liquid mud including cost of pumping or bailing out water and removing slush etc. complete. Note for item No. 4.15:- The quantity will be calculated by multiplying. The depth of centre of gravity shall be reckoned correct to 0.1m. 0.05m or more shall be taken as 0.1m and less than 0.05m ignored.

Extra for laying concrete in or under foul positions.

Making plinth protection 50mm thick of cement concrete grade M10 over 75mm bed of dry metal ballast 40mm nominal size well rammed and consolidated and filled with sand including finishing the top smooth (with 20mm nominal size graded stone aggregate.)

Extra for addition of synthetic polyester triangular fiber of length 12 mm, effective diameter 10-40 microns and specific gravity of 1.34 to 1.40 in cement concrete/RCC/Flooring/ Water retaining structures by using 125 gms of synthetic polyester triangular fibre for 50 kgs cement used as per directions of Engineer-in- Charge.

Precasting and placing in position 125 mm dia Bollards 600 mm high of required shape including providing M.S. Pipe welded at bottom and embedded 150mm in cement concrete 1:3:6 (1 Cement : 3 sand : 6 graded stone aggregate 20 mm nominal size) including necessary excavation of size 250x250x450mm deep for the same in bitumen/concrete pavement at specified spacing.

Providing and fixing up to floor two level precast cement concrete string or lacing courses, copings, bed plates, anchor blocks, and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), cost of required Centering complete. 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20mm nominal size)

Providing and fixing up to floor two level precast cement concrete solid block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete . 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20mm nominal size)

Providing and fixing up to floor two level precast cement concrete hollow block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete. 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20mm nominal size)

Providing and laying in position ready mixed plain cement concrete, using fly ash and cement content as per approved design curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. Note : (1) Fly ash conforming to grade I of IS 3812 (Part-1) only be used as part replacemen to be ensured in accordance with clauses 5.2 and 5.2.1 of IS: 456 -2000 in the items of BMC and RMC.

All works up to plinth level:

M-20 grade plain cement concrete (cement content considered @ 280 kg/cum)

M-15 grade plain cement concrete (cement content considered @ 240 kg/cum)

M-10 grade plain cement concrete (cement content considered @ 220 kg/cum)

All works above plinth and upto floor two level

M-20 grade plain cement concrete (cement content considered @ 280 kg/cum)

M-15 grade plain cement concrete (cement content considered @ 240 kg/cum)

M-10 grade plain cement concrete (cement content considered @ 220 kg/cum)

Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in- charge.

All works up to plinth level:

M-20 grade plain cement concrete (cement content considered @ 280 kg/cum)

M-15 grade plain cement concrete (cement content considered @ 240 kg/cum)

M-10 grade plain cement concrete (cement content considered @ 220 kg/cum)

All works above plinth and upto floor two level

M-20 grade plain cement concrete (cement content considered @ 280 kg/cum)

M-15 grade plain cement concrete (cement content considered @ 240 kg/cum)

M-10 grade plain cement concrete (cement content considered @ 220 kg/cum)

Plum Cement concrete 1:2:4 with 75% graded metal of maximum size 40 mm and 25% plum of 150mm size.

Providing and laying cement concrete in Sunken floors of WC, Toilet, Wash Area, etc with 1:5:10 (1 cement : 5 coarse sand (zone-3) : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centering and shuttering

M-20 Grade Concrete

M-15 Grade Concrete

M-20 Grade Concrete

M-20 Grade Concrete

M-20 Grade Concrete

M-20 Grade Concrete

M-20 Grade Concrete

M-20 Grade Concrete

Foundations, footings, bases of columns, etc. for concrete upto plinth level

Walls (any thickness) in cluding attached pilasters butter esses, plinth beams and string courses etc.

Uptoplinthlevel.

Above plinth upto 3.6 m height from plinth level

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.6 m, for every additional height of 1 metre or part thereof.

Suspended floors, roofs, landings, balconies and access platform.

Shelves(Cast in situ)

Lintels, beams, girders, bressumers and cantilevers

Columns, P i l l a r s , Piers, Abutments, Posts and Struts.

Stairs, (excluding landings) except spiral- Staircases.

Spiral staircases (including landing).

Arches, domes,vaults upto 6m span

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.6 m, for every additional height of 1 metre or part thereof (Plan area to be measured)

Suspended floors, roofs, landing, beams and balconies (Plan area to be measured).

Providing, hoisting and fixing up to floor two level precast reinforced cement concrete in lintels, manhole cover, shelves and like including setting in cement mortar 1:3 (1 cement : 3 sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but excluding the cost of reinforcement with M 15 –Grade Concrete.

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 sand) etc. complete excluding plastering of the jambs, sills and soffits.

50 mm thick

40 mm thick

25 mm thick

Encasing rolled steel sections, in beams and columns, with cement concrete M 15 (1 cement: 2 sand: 4 graded stone aggregate 20mm nominal size) including centering and shuttering complete but excluding cost of reinforcement.

Encasing rolled steel section in grillages with cement concrete M 15 (1 cement: 2 sand: 4 graded stone aggregate 20 mm nominal size) including centering and shuttering but excluding cost of expanded metal and hangers.

Extra for providing and fixing expanded metal mesh of size 20x60mm and strands 3.25mm wide 1.6mm thick weighing 3.64 kg per sqm for encasing of rolled steel sections in beams, columns and grillages excluding cost of hangers.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding including cost of binding wire all wastages and overlaps, couplers (overlaps shall be provided as per requirement of IS 13920 for ductile detaling IS 456 RCC Design & SP 34 Reinforcement detailing ) etc. complete . (Note:-1. Spacer bars (chairs) shall be paid separately as shown in the drawing and as per direction of engineer in charge. 2. No extra payment shall be done for overlaps and/or couplers. 3.Couplers shall be conforming to IS code on “Reinforcement Couplers for Mechanical Splices of Bars for Concrete Reinforcement - Specification”)

Mild steel and Medium Tensile steel bars.

Hard drawn steel wire

Cold twisted bars (CTD)

Hot rolled deformed bars

Hard drawn steel wire fabric

Thermo-Mechanically Treated bars. (TMT/TMX) FE 500 or more conforming to IS 1786

Add extra for providing reinforcement above Floor two level for every additional floor or part thereof.

Providing and fixing in position copper plate as per design for expansion joints.

Providing and filling in position, blown bitumen in expansion joints.

Providing and filling in position bitumen mix filler of Proportion 80 kg. Of hot bitumen, 1 kg. Of cement and 0.25 cubic metre of sand for expansion joints.

Providing and filling gap in expansion joint between RCC/ Stone/Ceramic tiles/Granite/ Marble by providing silicon sealant over backer rod of approved quality weather sealant as per drawing and direction of engineer in charge up to 25mm width & 12 mm depth.

Providing and fixing in position bitumen impregnated fibre board conforming to IS: 1838 including cost of primer, sealing compound in expansion joints.

Providing and fixing sheet covering over expansion joints with iron screws as per design.

Providing for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Extra for laying reinforced cement concrete in or under water and/ or liquid mud including cost of pumping or bailing out water and removing slush etc., complete. Note- For Item No. 5.25:-The quantity will be calculated by multiplying the depth measured from the subsoil water level up to the centre of gravity The depth of centre of gravity shall be reckoned correct to 0.1 m. 0.05 m or more shall be taken as 0.1 m and less than 0.05 m ignored. No extra payment shall be made for placing reinforcement or centering & shuttering under sub – soil water condition

Extra for laying reinforced cement concrete in or under foul positions.

Providing and laying in position machine batched, machine mixed cement concrete (BMC) of M-25 grade for reinforced cement concrete work using cement content as per approved mix design concrete without impairing strength and durability as per direction of Engineer-in charge and pumping of concrete to site of laying and finishing but excluding the cost of centering, shuttering, and reinforcement. (Note: - Minimum cement content is 330 kg/cum) and no extra payment for extra cement used as per mix design.

All works upto plinth level.

All works above plinth level and upto floor five level.

Add extra for each floor for all works above floor five level.

Extra for providing richer mixes of BMC design mix as per item no 5.27 upto plinth level and at all floor levels. (No extra payment for using extra cement as per requirement of mix design.)

Providing and placing in position precast reinforced cement concrete waffle units square or rectangular as per design and shape for floors and roofs in M-20 –Grade Concrete (with graded stone aggregate 10mm nominal size. including provision of steel hooks for lifting and form work, handling, hoisting, centering and erection complete for all floor levels but excluding the cost of reinforcement.

Providing and laying in position ready mixed concrete (RMC) of M-25 grade for reinforced cement concrete work, using cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Note: Minimum cement content is @ 330 kg/cum. (No extra payment for using extra cement as per requirement of mix design.)

All works upto plinth level.

All works above plinth level and upto floor V level.

Extra for each additional floor for all works above floor five level

Extra for R.C.C. work above floor two level for each floors or part thereof. (except items 5.27 and 5.30)

Supplying and applying pre tested and approved water based concrete curing compound to concrete/ masonry surface, all as per manufacturer’s specification and direction of Engineer-in-charge.

Non pigmented wet curing compound

Pigmented wet curing compound.

Providing and fixing in position factory made precast RCC M-40 doors, windows and ventilator frames having excellent smooth finish, as per IS: 6523 with 6mm dia main reinforcement each polymer block having at least four holes for passing one or adjacent rebates to hold fast grill or steel bar, ventilator frame provided with grooves for louvers at an angel of 45 degree at spacing to block direct vision etc. complete, as per the direction of Engineer-in-charge. The cost of hold fast and cement concrete block of 1:3: 6 (1 Cement: 3 sand: 6 Graded stone aggregate 20mm nominal size) mix is also included in the item.

Smooth finishing of the exposed surface of RCC work with 6mm thick cement mortar 1:3 (1 cement: 3 sand).

Providing and fixing in position pre moulded compressible filler board made from polymer base in black color approved make conforming to the specifications having minimum density of 95 kg / cum, non- staining, with less than 1 percent water absorption and compression recovery of 93 percent minimum including cost of double sided adhesive tape, sealant etc. in expansion joints.

Providing and sealing the retaining wall expansion Joints with anodized aluminum extruded section of 135 mm × 3.1 mm confirm to alloy of 6063 T5/T6including fixing of an imported EPDM moisture Barrier conform to (American Society for Testing and Materials) 2240 & ASTM - G53 & 84 fixing with Epoxy adhesive confirm to ASTM C-881 complete in all respect as per manufacturer Drawing and specifications. With 5 year guarantee.

Providing and fixing sheet covering over expansion joints with iron screws as per design. Non- asbestos cement bonded particle board 6 mm thick as IS: 14276

150mm wide

200mm wide

250mm wide

Providing & laying in position Prestressing steel strands (low relaxation) on hollow core bed by using mechanical pulling arrangement like Rabbit/ Bed master including all accessories for Stressing &destressing operations as per approved make conforming to IS1343 & grade FY-1860 etc, complete as per drawings and direction of Engineer -in- charge.

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In- Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer - inCharge. (Material shall confirm to ASTM 6063).

Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063).

Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members with, self aligning and self centeringarragement support plates asper ASTM B221-02. . The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063.)

Roof Joint for 100 mm gap

Roof Joint for 150 mm gap

Roof Joint for 200 mm gap

Providing and fixing Scaffolding net of required width made of high density Polyethylene UV stabilized knitted on warp knitting machines having density 100gm/sqm and shading coefficient minimum 75% around the construction site/ for vertical extension as per requirement including fastening/tying with building/scaffolding pipes or with any other fixtures etc. complete as per direction of Engineer-in-Charge. (One time payment shall be made for providing Scaffolding net from start of work till completion of work including shifting if any. The Scaffolding net shall be the property of the contractor on completion of the work)

Cement mortar 1:4 (1 cement : 4 sand)

Cement mortar 1:6 (1 cement : 6 sand)

Cement mortar 1:4 (1 cement : 4 sand)

Cement mortar 1:6 (1 cement : 6 sand)

Cement mortar 1:4 (1 cement : 4 sand)

Cement Mortar 1:6 (1 cement:6 sand).

Cement mortar 1:4 (1 cement : 4 sand)

Cement Mortar 1:6 (1 cement:6 sand).

Cement mortar 1:4 (1 cement : 4 sand)

Cement Mortar 1:6 (1 cement: 6 sand).

Cement mortar 1:4 (1 cement : 4 sand)

Cement Mortar 1:6 (1 cement : 6 sand)

Having 100 kg / cm2 average compressive strength.

Cement mortar 1:4 (1 cement : 4 sand)

Cement mortar 1:6 (1 cement : 6 sand)

Having 75 kg / cm2 average compressive strength.

Cement mortar 1:4 (1 cement : 4 sand)

Cement mortar 1:6 (1 cement : 6 sand)

Having 50 kg / cm2 average compressive strength.

Cement mortar 1:4 (1 cement : 4 sand)

Cement mortar 1:6 (1 cement : 6 sand)

Cement mortar 1:4 (1 cement : 4 sand)

Cement mortar 1:6 (1 cement : 6 sand)

Brick work with extruded burnt fly ash clay sewer bricks (conforming to IS: 4885) in archesin foundation and plinth including centering and shuttering complete in cement mortar 1:3 (1 cement: 3 sand).

Extra for brick work in superstructure above floor two levels for each additional floor or part thereof respective item .

Providing half brick masonry with well burnt chimney bricks in bull patent trench kiln manufactured by ghol process crushing strength not less than 40 kg /cm2 and water absorption not more than 15% in superstructure above plinth level and up to floor two level.

Cement mortar 1:3 (1 cement : 3 sand)

Cement mortar 1:4 (1 cement : 4 sand)

Providing half brick masonry with well burnt chimney bricks in bull pattern trench kiln crushing strength not less than 25 kg /cm2 and water absorption not more than 20% in superstructure above plinth level and up to floor two level.

Cement mortar 1:3 (1 cement : 3 sand)

Cement mortar 1:4 (1 cement : 4 sand)

Providing half brick masonry with well burnt open bhatta bricks crushing strength not less than 25 kg /cm2 and water absorption not more than 20% in superstructure above plinth level and up to floor two level

Cement mortar 1:3 (1 cement : 3 sand)

Cement mortar 1:4 (1 cement : 4 sand)

Half brick masonry with fly ash lime Gypsum bricks (FALG bricks) conforming to IS: 12894, in super structure above plinth and upto floor two level.

Having 100 kg/cm2 average compressive strength.

Cement mortar 1 : 3 (1 cement : 3 sand)

Cement mortar 1 : 4 (1 cement : 4 sand)

Having 75 kg/cm2 average compressive strength.

Cement mortar 1 : 3 (1 cement : 3 sand)

Cement mortar 1 : 4 (1 cement : 4 sand)

Having 50 kg/cm2 average compressive strength.

Cement mortar 1 : 3 (1 cement : 3 sand)

Cement mortar 1 : 4 (1 cement : 4 sand)

Extra for half brick masonry in superstructure, above floor two level for every floor or part thereof respective item.

Extra for providing and placing in position 2 Nos. 8mm dia. M.S. bars at every third course of in half brick masonry.

Honey-comb brick work 10 cm thick with well burnt chimney bricks manufactured by ghol process crushing strength not less than 40kg /sqcm and water absorption not more than 15% in cement mortar 1:4 (1 cement : 4 sand).

Extra for forming cavity 5cm to 7.5cm wide in cavity walls with necessary weep and vent holes including use of cores and cost of providing and fixing bitumastic coated M .S. Ties 300mm long of 25x3mm section at not less than 3 ties per sqm as per approved design

Brick work in plain arches in superstructure including centering and shuttering complete with chimney bricks having crushing strength not less than 40kg /cm2 and water absorption not more than 15% in cement mortar 1:3 (1 cement : 3 sand).

Brick work in gauged arches in superstructure in cement mortar 1:3 (1 cement : 3 sand) including centering and shuttering complete, with chimney bricks having crushing strength not less than 40kg /cm2 and water absorption not more than 15%

Providing half brick masonry with kiln burnt clay bricks of 40kg /cm2 and water absorption not more than 15% in cement mortar 1:3 (1 Cement : 3 sand) in superstructure for closing cavity 5 to 7.5 cm wide in cavity wall complete with 10 cm wide bitumen felt type 3 grade 1.

Extra for laying brick work in or under water and/or liquid mud including cost of pumping or bailing out water and removing slush etc. complete. NOTE: - The quantity will be calculated by multiplying the depth measured from sub - soil water level up to the centre of gravity of brick work in cum executed under the sub - soil water. The depth of centre of gravity shall be reckoned correct to 0.1 m. 0.05 m or more shall be taken as 0.1 m and less than 0.05 m ignored.

Extra for laying brick work in or under foul position.

Providing and laying cellular concrete blocks masonry having density ranging from 800kg/m3 in super structure above plinth level up to floor two level in cement mortar 1:4 (1 cement: 4 sand) The nominal dimensions of the concrete blocks shall be as follows in additional block shall be of half lengths of 200, 250 or 300 mm to correspond to the full lengths. The size of the blocks specified other than those specified may also be used.

Providing and laying Autoclaved Aerated Concrete (AAC) blocks masonry, using AAC blocks (Size length 300, 400, 500, 600 mm Height 200, 250, 300 mm Width 100, 150, 200, 250 mm) conforming to IS 2185 PART 3, having compressive strength not less than 4 MPa (Grade II) in super structure, blocks jointed with approved block laying polymer modified adhesive mortar as per ASTM international standard including raking out joints. Vertical bands shall be placed along jams (vertical member of chowkhats) and extend upto lintel levels to arrest cracking at corner openings. RCC bands shall be measured with AAC block masonry. Rates include all materials including steel bars, wastages, scaffolding and all labour etc. complete.

AAC Masonry in polymer modified mortar

Extra for AAC masonry work in superstructure above floor two level for each additional floor or part thereof

Providing hoisting & fixing precast Autoclaved Aerated Concrete (AAC) reinforced roof slabs, lintels and chhajjas as per IS: 6073 -2006 grade D specifications (dry density, without steel, 550 kg/m3 to 650 kg/m3 and minimum compressive strength 3.5 N/mm2) reinforcement steel provided inside AAC slab, lintel and chhajja shall be ascertained on the basis of manufacturer’s certificate and also by random destructive testing done by engineer-in-charge or his representative for which cost of samples and testing charges shall be borne by the contractor. Deflection & ultimate load test for AAC reinforced roof slab and lintel shall be as per annex. B of IS: 6073 -2006 and criteria for conformity and sampling shall be as per clause-13 of IS: 6073 -2006.

Precast autoclaved aerated concrete (AAC) reinforced wall panels:- Providing hoisting & fixing precast Autoclaved Aerated Concrete (AAC) reinforced wall panels as per IS:6072 -1972 grade D (dry density, without steel, 550 kg/m3 to 650 kg/m3 and inside AAC panels. Quantity of reinforcement steel in AAC panels shall be ascertained on the basis of certificate of the manufacturer and also by random destructive testing by engineer-in- charge or his representative for which cost of samples and testing charges shall be borne by the contractor. Cost of reinforcement inside AAC panels shall be paid separately.

Add extra for AAC wall panels, roof slabs, lintels and chhajjas above floor two level for each additional floor as per item no 6.29 and 6.30.

From ground level upto plinth level

Above plinth level upto floor II level

Brick work with modular bricks of class designation 7.5 in exposed brick work including making horizontal and vertical grooves 10mm wide 12mm deep complete from ground level up to plinth level in cement mortar 1:6 (1 cement : 6 coarse sand)

From ground level upto plinth level

Above plinth level upto floor II level

Providing and laying Gypsum panel partitions 100 mm thick with water proof Gypsum panels of size 666x500x100 mm, made of calcite phosphor Gypsum fixed with tongue and groove, jointed with bonding plaster as per manufacturer’s specifications in superstructure above plinth level up to floor two level. Gypsum blocks will have a minimum compressive strength of 9.3 kg/cm2

Extra for Gypsum panel Partitions in superstructure above floor two level for every four floors or part thereof.

Cement mortar 1:6 (1 cement : 6 sand)

Cement mortar 1:6 (1cement: 6 sand).

Square or rectangular pillars

Circular pillars.

Cement mortar 1:6 (1 cement : 6 sand)

Cement mortar 1:6 (1 cement : 6 sand)

Masonry work (first sort) in cement mortar 1:6 (1 cement : 6 sand)

Masonry work (second sort) , in cement mortar 1:6 (1 cement : 6 sand)

Square or rectangular pillars

Circular pillars.

Extra for coursed rubble masonry with hard stone (first or second sort) curved on plan for a mean radius not exceeding 6 m.

Stone work in plain ashlar masonry in super structure upto floor two level in cement mortar 1:6 (1 cement : 6 sand) including pointing with cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment matching the sand stone shade :

One face dressed.

Red sand stone

White sand stone

Both face dressed.

Red sand stone.

White sand stone

Stone work plain ashlar masonry in arches in super structure upto floor two level in cement mortar 1:3 (1 cement: 3 sand) including centering, shuttering and pointing with white cement mortar 1:2 (1 white cement: 2 marble dust) with an admixture of pigment matching the sand stone shade.

One face dressed.

Red sand stone

White sand stone

Both face dressed.

Red sand stone.

White sand stone

Stone work plain ashlar masonry in domes, in super structure upto floor two level in cement mortar 1:3 (1 cement: 3 sand) including centering, shuttering and pointing with white cement mortar 1:2 (1 white cement: 2 marble dust) with an admixture of pigment matching the sand stone shade.

One face dressed

Red sand stone

White sand stone

Both face dressed.

Red sand stone.

White sand stone.

Stone work ashlar masonry punched (ordinary) in superstructure above plinth level and upto floor two level in cement mortar 1:6 (1 white cement: 6 sand) including pointing with cement mortar 1:2 (1 white cement: 2 marble dust) with an admixture of pigment matching the sand stone shade.

Red sand stone one face punched.

Red sand stone both face punched

White sand stone one face punched.

White sand stone double face punched

Extra for stone work, plain ashlar or ashlar punched above floor two level for every floor or part thereof.

Extra for plain ashlar or ashlar punched in :

Square or rectangular pillars

Extra for stone work; plain ashlar or ashlar punched in curved on plan with a mean radius not exceeding 6 m.

Extra for additional cost of centering for arches exceeding 6m span including all strutting, bolting, wedging etc. And removal (area of soffit to be measured).

Stone work sunk or moulded or sunk and moulded upto floor Two level in cement mortar 1:6 (1cement : 6 sand) including pointing with white cement mortar 1:2 (1 white : 2 marble dust) with an admixture of pigment matching the stone shade :

Red sand stone

White sand stone

Extra for stone work sunk or moulded or sunk and moulded or carved in :

Triangular or Square or rectangular pillars

Circular or polygonal pillars

Extra for stone work sunk or moulded in cornices.

Stone work (machine cut edges) for wall lining etc. (veneer work) up to 10 meter height backing filled with a grout of 12mm thick cement mortar 1:3 (1 cement : 3 sand) including pointing in white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment matching the stone shade : (To be secured to the backing by means of clamps which shall be paid for separately):

Red sand stone - exposed face fine dressed with rough backing.

70 mm thick.

60 mm thick.

50 mm thick

40 mm thick.

30 mm thick.

Red sand stone - Exposed face machine cut and table rubbed with rough backing.

70 mm thick.

60 mm thick.

50 mm thick

40 mm thick.

30 mm thick.

White sand stone - exposed face fine dressed with rough backing.

70 mm thick.

60 mm thick.

50 mm thick

40 mm thick.

30 mm thick.

White sand stone - Exposed face machine cut and table rubbed with rough backing.

70 mm thick.

60 mm thick.

50 mm thick

40 mm thick.

30 mm thick.

Extra for stone work (veneer work) curved on plan with a mean radius not exceeding 6 m.

Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement :2 sand) including making the necessary chases in stone and holes in walls wherever required.

Providing and fixing stone dowels of size 10x5x2.5cm cut to double wedge shape as per design in cement mortar 1:2 (1 cement : 2 sand) including making the necessary chases

Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 sand) including making the necessary chases.

Providing and fixing sloping chajja of stone 40 mm thick and upto 80 cm wide beyond the wall as measured along the slope in cement mortar 1:4 (1 cement : 4 sand) including pointing in cement mortar 1:2 (1 white cement: 2 marble dust) with an admixture of pigment matching the stone shade:

Red sand stone: With common burnt clay bricks of 25 kg/cm2 compressive strength.

White sand stone: With common burnt clay bricks of 25 kg/cm2 compressive strength.

Providing and fixing horizontal chajja of stone 40 mm thick and upto 80 cm projection in cement mortar 1:4 (1 cement : 4 sand) including pointing in white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment matching the stone shade:

Red sand stone

White sand stone

30mm red sand stone sun-shade (chisel-dressed) supported on red sand stone brackets, fixed in walls with cement mortar 1:4 (1 cement: 4 sand) including finishing complete.

Providing and fixing red sand stone brackets 55x22.5x45cm sunk and moulded including providing and fixing with 4 Nos. gun metal cramp 25x6mm 30 cm long and dowel bars 7.5 cm long 6 mm dia as per design.

Stone work, plain in copings, cornices, string courses and plinth courses, upto 75 mm thick in Cement mortar 1:6 (1 cement : 6 sand) including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade.

Red sand stone

White sand stone

Providing and fixing stone jali 40mm thick throughout in cement mortar 1:3 (1cement :3 sand) including pointing in white cement mortar 1:2 (1white cement: 2stone dust) with an admixture of pigment , matching the stone shade, jali slab without any chamfers etc.

Red sand stone

White sand stone

Extra for laying stone work in or under water and/or liquid mud including cost of pumping or bailing out water and removing slush etc. complete. NOTE: - The quantity will be calculated by multiplying the depth measured from sub - soil water level up to the centre of gravity of stone work in cum executed under the sub - soil water. The depth of centre of gravity shall be reckoned correct to 0.1 m. 0.05 m or more shall be taken as 0.1 m and less than 0.05 m ignored.

Extra for laying stone work in or under foul position.

Wall lining butch work upto 10m height with red/ white sand stone 40 mm thick rough facing on the exposed surface with stone strips of minimum length 300 mm and required width 75mm thick strips i/c 12mm thick bed of cement mortar 1:3 (1 Cement : 3 sand) i/c ruled pointing in cement mortar 1:2 (1 white cement: 2 marble dust) with an admixture of pigment to match the shade of stone complete as per direction of Engineer-in- charge.

Stone work ( machine cut edges) for wall lining upto 10 m height etc. (Veneer work) backing filled with a grout of 12mm thick cement mortar 1:3 (1 Cement : 3 sand) and jointed with Cement mortar 1:2 (1 cement : 2 marble dust) including rubbing and polishing complete. (To be secured to the backing by means of cramps which shall be paid for separately)

25mm thick Kota stone slabs exposed face dressed and rubbed.

25mm thick Dholpur stone slabs exposed face dressed and rubbed.

20 to 25mm thick kota stone slabs exposed slab not dressed and rubbed.

20 to 25mm thick Dholpur stone/shivpuri stone not dressed and rubbed.

Stone tile work with 8mm thick mirror polished and machine cut edge for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 sand), including pointing in white cement with an admixture of pigment to match the stone shade.

Granite stone of any colour and shade

Raj Nagar plain white marble/ Udaipur green marble/ Zebra black marble

Extra for stone work for wall lining on exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Providing and fixing dry stone cladding upto 10 metre height with 30mm thick gang saw cut stone with (machine cut edges) of uniform colour and/ or with the help of cramps, pins etc. And sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins. shall be paid for separately.)

Red sand stone.

White sand stone

Providing and fixing structural steel frame (for dry stone cladding with 30 mm thick gang saw cut with machine cut edges sand stone) on walls at all heights using M.S. square/rectangular tube in the required pattern as per architectural drawing including including drilling necessary steel work will be given a priming coat of Zinc primer as approved by Engineer-in-charge and painted with two or more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the Engineer-in-charge for approval before execution).The frame work shall be fixed in true horizontal and vertical lines/ planes. (Only structural steel frame work shall be measured for the purpose of payment, stainless steel clamps shall be paid for separately and nothing extra shall be paid.)

Providing and fixing adjustable stainless steel clamps of approved quality and of required shape and size adjustable with stainless steel nuts bolts and washer (total weight not less than 260 gms) for dry stone cladding fixed on frame

4 mm thick alumminium composite pannel material consisting of 3 mm thick FR grade mineral core sandwiched between two alumminium sheets (each 0.5mm thick)

4 mm thick alumminium composite pannel material consisting of 3.5 mm thick FR grade mineral core sandwiched between two alumminium sheets (each 0.25mm thick)

3 mm thick alumminium composite pannel material consisting of 2.5 mm thick FR grade mineral core sandwiched between two alumminium sheets (each 0.25mm thick)

Providing and fixing Aluminium Magnesium alloy Plain Panel Sun Louvres of approved colour consisting of panel 84 mm wide x 16mm deep x 0.6mm thick with round edges panel length upto 6 mtrs coil coated on a continuos paint line double baked between metal and paint, enamelled twice under high temperature one side with full primer and finish, the other side (inner side) with a primer coat and Skin Coat on a Continuos Paint Line. Note: - 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. upto two decimal places.

Second class teak wood

Sal wood

Kiln Head wood seasoned and chemically treated hard wood (Haldu, Kail, Bija wood.)

Factory made Kiln seasoned, chemically treated, finger jointed at spacing not closer than 50 cm, 2nd class hard wood.

Frame of size 100mmX60mm single or double rebate

Frame of size 120mmX60mm double rebate.

Sal wood

Kiln seasoned and chemically treated hardwood Haldu, Kail, Bija wood.

Factory made Kiln seasoned, chemically treated, finger jointed at spacing not closer than 50 cm, 2nd class hard wood.

Second class teak wood

Sal wood

Kiln seasoned and chemically treated Haldu, Kail, Bija wood.

Factory made Kiln seasoned, chemically treated, finger jointed at spacing not closer than 50 cm, 2nd class hard wood.

Second class teak wood

35 mm thick shutters

30 mm thick shutters

Kiln seasoned and chemically treated hardwood Haldu, Kail, Bija wood.

35 mm thick shutters

30 mm thick shutters

35 mm thick shutters

30 mm thick shutters

Factory made Kiln seasoned chemically treated and finger jointed at spacing not closer than 50cm, 2nd class hard wood shutters

35 mm thick

30 mm thick

Second class teak wood

Kiln seasoned and chemically treated Haldu, Kail, Bija wood

15mm thick Factory made Kiln seasoned, chemically treated and finger jointed at spacing not closer than 50cm, 2nd class hard wood.

Ply wood 5 ply, 9 mm thick :

Decorative plywood both side decorative veneer (Type - I) conforming to IS 1328 BWR type.

Decorative plywood one side decorative veneer and commercial veneer on other face (Type 1) conforming to IS 1328 BWR Type

Ply wood 7 ply, 9 mm thick :

Decorative plywood both side decorative veneer (Type- I) conforming to IS 1328 BWR type.

Decorative plywood one side decorative veneer and commercial veneer on other face (Type-1) conforming to IS 1328 BWR Type

Particle Board 12 mm thick

Plain particle board flat pressed, 3 layer or graded wood particle board medium density Grade I, IS: 3087 marked.

Veneered flat pressed three layer or graded wood particle board with commercial veneering on both sides conforming to IS: 3097, grade I.

Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side, Grade I, Type II IS: 12823 marked.

Pre-laminated particle board with decorative lamination on both sides, Grade I, Type II, IS: 12823 marked.

Coir Veneer Board (conforming to IS 14842) 12 mm thick

Float glass panes

4 mm thick glass pane (weight not less than 10 kg/sqm)

5 mm thick glass pane (weight not less than 12.5 kg/sqm)

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. Wire and 1.4 mm wide aperture with matching wood beading

4mm to 5mm thick integral PVC form sheet with Celluka finish surface on both side with density not less than 600 kg/cum

4mm to 5mm thick laminated PVC form sheet with density not less than 600 kg/cum, laminated on both sides by 0.12 mm thick laminated sheet with density not less than 1400 kg/cum

12mm thick plain grade - 1, medium density flat pressed three layer particle board FPT - I or graded wood particle board FPT - I IS : 3087 marked bonded with BWP type synthetic resin adhesive as per IS : 848 :

12 mm thick pre-laminated particle board (decorative lamination on both sides) grade - 1, medium density flat pressed, three layer particle board FPT - I or graded wood particle board FPT - I, conforming to IS : 3087 bonded with BWP type synthetic resin adhesive as per IS : 848 and pre- lamination conforming to IS : 12823 Grade 1, Type - II marked:

12 mm thick one side pre-laminated particle board (decorative lamination on one side and other sides balancing lamination) grade - 1 medium density flat pressed, three layer particle board FPT - I or graded wood particle board FPT-1 conforming to IS : 3087 bonded with BWP type synthetic resin adhesive as per IS : 848 and prelamination conforming to IS : 12823 Grade -1, Type II marked:

Second class teak wood

35 mm thick

30 mm thick

Kiln seasoned and chemically treated Haldu, Kail, Bija wood

35 mm thick

30 mm thick

35 mm thick

30 mm thick

Factory made Kiln seasoned chemically treated and finger jointed at spacing not closer than 50cm, 2nd class hard wood

Extra for providing heavy sheet float glass panes instead of ordinary float glass in glazed doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured)

5 mm thick instead of 4 mm thick.

10 to 12 mm float glass

5.5 mm safety glass

10-12mm safety glass

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Deduct for providing pin headed glass panes instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory windows, shutters (Area of opening for glass panes excluding portion inside rebate shall be measured).

Extra for S.S, hinges providing ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws. (Shutter area to be measured).

Deduct for not providing hinges in doors, windows or clerestory window shutters with :

Stainless steel butt hinges with stainless steel screws for 2nd class teak wood and other class of wood shutters.

ISI marked M.S. pressed butt hinges bright finished of required size For 2nd class teak wood and other class of wood shutters.

Providing and fixing 25 mm thick Second class teak wood shutters using 4mm float glass for cup board etc. :

Panelled or panelled and glazed shutters :

Using ISI marked anodised aluminium butt hinges with necessary screws.

Using ISI marked nickel plated bright finished M.S. piano hinges with necessary screws.

Glazed shutters :

Second class teak wood including ISI marked anodised aluminium butt hinges with necessary screws.

Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately) :

12 mm thick

18 mm thick

Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately).

18 mm thick

25 mm thick

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutter.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS: 3818 marked with necessary screws.

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

25mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws.

Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I) On one side only.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured) :

Rectangular or square.

Circular.

Extra if louvers (not exceeding 0.2 sqm) are provided in flush door shutters (overall area of door shutters to be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing wire gauze shutters using galvanised M.S. wire gauze of average width of aperture 1.4mm in both direction with wire of dia. 0.63 mm for doors, windows and clerestory windows with hinges and necessary screws:

35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size.

Second class teak wood.

Kiln seasoned and chemically treated Haldu, Kail, Bija wood.

35 mm thick shutters with ISI marked stainless steel butt hinges of required size.

Second class teak wood.

Kiln seasoned and chemically treated Haldu, Kail, Bija wood.

30 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size.

Second class teak wood.

Kiln seasoned and chemically treated Haldu, Kail, Bija wood.

30 mm thick shutters with ISI marked stainless steel butt hinges of required size.

Second class teak wood.

Kiln seasoned and chemically treated Haldu, Kail, Bija wood.

Providing and fixing wire gauge laminated veneer lumber shutters conforming to IS : 14616, and as per TADS 15 :2001 (Part B) using galvanised wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm as per IS :1568 for doors, windows and clerestory windows including ISI marked M.S. pressed fixing with butt hinges bright finished of required size with necessary screws as per directions of Engineer-in-charge:

35 mm thick shutters

30 mm thick shutters

Providing 50x50x50mm 2nd class teak wood plugs including cutting brick work and fixing in cement mortar 1:3 (1 cement : 3 sand) and making good the walls etc.

Providing and fixing expandable fasteners of specified size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete.

25 mm long

32 mm long

40 mm long

50 mm long

60 mm long

Providing and fixing 2nd class teak wood plain lining tongued and grooved including wooden plugs complete with necessary screws and priming coat on unexposed surface.

40 mm thick.

25 mm thick.

20 mm thick

12 mm thick

Providing and fixing in wall lining flat pressed three layer (medium density) particle board or graded wood Pre- laminated one side decorative lamination on other side balancing lamination Grade I, Type II, IS : 12823 marked including priming coat on unexposed surface, with necessary fixing arrangement and screws etc. complete :

12 mm thick

18 mm thick

25 mm thick

Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and drilling necessary holes for rawl plug etc. including priming coat complete. Kiln seasoned and chemically treated Haldu, Kail, Bija wood.

Providing and fixing plywood 4 mm thick one side decorative veneer conforming to IS: 1328 (type-1) for plain lining / cladding with necessary screws, priming coat on unexposed surface with: Decorative veneer facings of approved manufacture.

Providing and fixing 4mm thick coir veneer board, ISI marked IS: 14842, plain lining with necessary screws, priming coat on unexposed surface etc., complete.

Providing and fixing skirting of Pre- laminated with (one side decorative and other side balancing lamination) flat pressed, 3 layer or graded particle board (medium density) Grade I, Type II, IS :12823 marked, with necessary fixing arrangements and screws including drilling necessary holes for rawl plugs etc. and priming coat on unexposed surface complete :

18 mm thick

25 mm thick

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :

2nd class teak wood

Kiln seasoned and chemically treated Haldu, Kail, Bija wood.

Providing and fixing plain jaffri of 35x10 mm laths placed 35 mm apart (frames to be paid separately) including fixing 50x12 mm beading complete with : Second class teak wood.

Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, IS : 3087 marked,, including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet with Haldu, Kail, Bija wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.

Providing and fixing 18 mm thick, 150 mm wide pelmet of coir veneer board ISI marked IS: 14842, including top cover of 6 mm coir veneer board, nickle plated brackets, including fixing with 25x3 mm M.S. Flat 10 cm long fixed to pelmet with Haldu, Kail, Bija wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.

Extra for using veneered particle board conforming to IS 3097 Grade I, in item of pelmet 18mm thick 150mm wide.

Non decorative veneer on both sides.

Particle board with decorative veneering on both sides.

Providing and fixing teak wood lipping of size 25x3 mm in pelmet.

Providing and fixing of 1.25 mm thick chromium plated brass plate, with two chromium plated curtain rods brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete:

12 mm dia.

20 mm dia.

25 mm dia.

Providing and fixing nickel plated curtain rods M.S. pipe with nickel plated brackets :

20 mm dia (heavy type)

25 mm dia (heavy type)

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to steel windows by welding.

Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing expanded metal 20x60 mm strands 3.25 mm wide and 1.6 mm thick for windows etc. including 62 x19 mm beading of II nd class teak wood and priming coat with approved steel primer all complete.

Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete.

Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm all complete.

With 2nd class teak wood beading 62x19 mm.

With 12 mm mild steel U beading.

Deduct for fixing 75x25 mm hard drawn steel wire fabric of weight not less than 7.75 Kg. per sqm in panelled and glazed door and window shutter instead of glass sheet 4 mm thick.

Providing 40x5 mm flat (iron hold fast 40 cm long) (0.628 kg) including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 sand : 6 graded stone aggregate 20mm nominal size)

Providing wooden beams including hoisting, fixing in position and applying wood preservative for the unexposed surfaces, etc. complete with :

Sal wood.

Haldu, Kail, Bija wood.

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete :

Providing and fixing IS : 1341 marked M.S. heavy weight butt hinges with necessary screws etc. complete :

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete.

Providing and fixing ISI marked oxidised M.S. pressed Parliamentary hinges with necessary screws etc. complete :

150x125x27x2.80 mm

125x125x27x2.80 mm

100x125x27x2.80 mm

75x100x20x2.24 mm

Providing and fixing ISI marked oxidised M.S. single acting spring hinges with necessary screws etc. complete :

Providing and fixing oxidised M.S. double acting spring hinges with necessary screws etc. complete.

Providing M.S. Piano hinges ISI marked IS: 3818 finished with nickel plating and fixing with necessary screws etc., complete.

Overall width 35 mm.

Overall width 50 mm.

Overall width 65 mm.

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete:

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :

Providing and fixing ISI marked 85x42mm oxidised M.S. pull bolt lock conforming to IS: 7534 with necessary screws bolts, nut and washers etc. complete

Providing and fixing ISI marked oxidised M.S. door latches conforming to IS:5930 with screws etc. complete :

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :

Providing and fixing oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete :

Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete.

300 mm weighing not less than 200 gms.

250 mm weighing not less than 150 gms.

200 mm weighing not less than 120 gms.

Providing and fixing oxidised M.S. Safety chain with necessary fixtures for doors. (Weighing not less than 450 gms.)

Providing and fixing ISI marked stainless steel sliding door bolts with nuts and screws etc. complete:

Providing and fixing ISI marked stainless steel tower bolt black finish, (Barrel type) with necessary screws etc. complete :

Providing and fixing ISI marked 85x42mm stainless steel pull bolt lock with necessary screws bolts, nut and washers etc. complete.

Providing and fixing ISI marked stainless steel door latches with screws etc. complete :

Providing and fixing ISI marked stainless steel handles with necessary screws etc. complete :

Providing and fixing stainless steel hasp and staple (safety type) conforming to IS specification with necessary screws etc. complete :

Providing and fixing stainless steel casement stays (straight peg type) conforming to IS specification with necessary screws etc. complete.

300 mm weighing not less than 200 gms.

250 mm weighing not less than 150 gms.

200 mm weighing not less than 120 gms.

Providing and fixing stainless steel safety chain with necessary fixtures for doors. Conforming to IS specification (Weighing not less than 450 gms.)

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete :

Providing and fixing 50 mm Stainless steel cup board or wardrobe knob with necessary screws (best make of approved quality)

Providing and fixing Stainless steel hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete :

125x85x5.5 mm (heavy type)

125x70x4 mm (ordinary type)

100x85x5.5 mm (heavy type)

100x70x4 mm (ordinary type)

75x65x4 mm (heavy type)

75x40x2.5 mm (ordinary type)

50x40x2.5 mm (ordinary type)

Providing and fixing bright finished brass parliamentary hinges with necessary screws etc. complete :

150x125x27x5 mm

125x125x27x5 mm

100x125x27x5 mm

75x100x20x3.2 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :

Providing and fixing bright finished brass door latch with necessary screws etc. complete.

Providing and fixing bright finished brass handles with necessary screws etc. complete.

Providing and fixing bright finished brass sliding door bolts with nuts and screws etc complete.

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality).

Providing and fixing bright finished brass 100 mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles with necessary screws etc. complete (Best make of approved quality).

Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles with necessary screws etc. complete (best make of approved quality).

Providing and fixing bright finished brass night latch including necessary screws etc. complete (best make of approved quality).

Providing and fixing special quality bright finished brass cupboard or wardrobe locks with four levers including necessary screws etc. complete (best make of approved quality) :

Providing and fixing 50 mm bright finished brass cup board or wardrobe knob with necessary screws (best make of approved quality)

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing bright finished brass casement window fastener with necessary screws etc. complete.

Providing and fixing bright finished brass casement stays (straight peg type) with necessary screws etc. complete :

300 mm weighing not less than 330 gms

250 mm weighing not less than 280 gms

200 mm weighing not less than 240 gms

Providing and fixing bright finished brass hasp and staple (safety type) with necessary screws etc. complete:

Providing and fixing Cromium plated brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm) with necessary accessories and screws etc. complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm) with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality).

Providing and fixing chromium plated brass 100 mm mortice latch with one dead bolt and a pair of lever handles with necessary screws etc. complete (best make of approved quality).

Providing and fixing chromium plated brass night latch including necessary screws etc. complete (Best make of approved quality).

Providing and fixing special quality chromium plated brass cupboard locks with six levers including necessary screws etc. complete (Best make of approved quality) of :

Size 40 mm

Size 50 mm

Size 65 mm

Size 75 mm

300 mm weighing not less than 330 gms

250 mm weighing not less than 280 gms

200 mm weighing not less than 240 gms

Single rubber stopper

Twin rubber stopper

125x34x24 mm weighing not less than 23 gms.

150x34x24 mm weighing not less than 26 gms.

75x60x10 mm fitted with 5.5 mm dia M.S. Bright Bar Rod weighing not less than 34 gms.

100x75x10 mm fitted with 5.5 mm dia MS Bright Bar Rod weighing not less than 53 gms.

152x42x18 mm weighing not less than 60 gms.

202x42x18 mm weighing not less than 78 gms.

35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size.

Second class teak wood.

Kiln seasoned and chemically treated Haldu, Kail, Bija wood.

35 mm thick shutters with ISI marked stainless steel butt hinges of required size.

Second class teak wood.

Kiln seasoned and chemically treated Haldu, Kail, Bija wood.

30 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size.

Second class teak wood.

Kiln seasoned and chemically treated Haldu, Kail, Bija wood.

30 mm thick shutters with ISI marked stainless steel butt hinges of required size.

Second class teak wood.

Kiln seasoned and chemically treated Haldu, Kail, Bija wood.

With 2nd class teak wood beading 62x19 mm.

With 12 mm mild steel U beading.

Triple strip vertical type.

Double strip (horizontal type).

300mm long

450mm long

500mm long

Marine plywood conforming to IS: 710

Fire retardant plywood conforming to IS: 5509.

1.5 mm thick.

1.0 mm thick.

With decorative veneering on one side and commercial veneering on other side.

With non decorative veneering on both sides.

12 mm thick.

18 mm thick.

25 mm thick.

18 mm thick

25 mm thick

75mm overall thickness partition with 12.5 mm thick double skin fire rated glass reinforced gypsum (GRG) plaster board conforming to IS: 2095: part 3 1996 Board with BIS certification marks.

75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming to IS:2095: part I 1996 Board with BIS certification marks.

66mm overall thickness Partition with 8mm thick double skin Calcium Silicate Board made with Calcareous and Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process with Compressive Strength 225 kg/sq.cm, Bending Strength 100 kg./sq.cm.

66mm overall thickness partition using 8mm thick double skin non- asbestos multipurpose cement board reinforced with cellulose fibre manufactured through autoclaving process (High pressure steam cured) as per IS: 14862 with suitable fibre cement screw.

68mm overall thickness partition using 9mm thick Heavy Duty Fibre Cement Board double skin non asbestos, reinforced with cellulose fibre,manufactured through autoclaving proces(High presssure steam cured)Type A, Category 4 conforming to IS 14862:2000. (for wet areas)

70 mm overall thickness Partition using 10mm thick double skin non-asbestost multipurpose termite, fire & moisure resistance (acoustic 30db) cement bonded particle board as per IS: 14276 with suitable cement bonded board screw.

10 mm thick tapered edge calcium silicate board made with calcareous and siliceous materials reinforced with cellulose fibre manufactured through autoclaving process to give stable crystalline structure, with compressive strength 225 kg/sq.cm, Bending strength 100 kg/sq.cm.

12 mm thick Gypsum board conforming to IS: 2095 Part-I.

8 mm thick non-asbestost multipurpose termite, fire & moisure resistance cement bonded particle board as per IS: 14276 with suitable cement bonded board screw.

8mm Both side Factory Prelamianted cement bonded particle board as per IS: 15786.

9mm thick non asbestos,heavy duty fibre cement board reinforced with cellulose fibre manufactured through autoclaving process(High pressure steam cured) Type A,Category 4, conforming to IS 14862.

Board 12 mm thick

Board 18 mm thick

18 mm thick

25 mm thick

Wt. 8.20 kg/m2

Wt. 4.2 kg/m2

12mm thick commercial ply conforming to IS: 1328 BWR type.

18mm thick commercial ply conforming to IS: 1328 BWR type.

Using 8mm thick magnesia block

Using10mm thick magnesia block

Using12mm thick magnesia block

Using12mm thick magnesia block

Extruded section Profile size 48x40 mm.

Extruded section Profile size 42x50 mm.

Plain PVC door shutters.

Pre laminated PVC door shutters.

Non decorative finish.

Decorative finish (both side wood grained finish).

Single rebate (75 mm X 50 mm)

Single rebate (100 mm X50 mm)

Single or double rebate (125 mm X 65 mm)

24 mm thick WPC (Wood polymer composite) solid plain flush door shutter

28 mm thick WPC (Wood polymer composite) solid plain flush door shutter

30 mm thick WPC (Wood polymer composite) solid plain flush door shutter

35 mm thick WPC (Wood polymer composite) solid plain flush door shutter

30 mm thick WPC (Wood Polymer Composite) solid decorative type flush door shutter

35 mm thick WPC (Wood Polymer Composite) solid decorative type flush door shutter

18 mm thick

25 mm thick

6 mm thick

12 mm thick

Non decorative finish (matt finish).

Decorative finish (wood grained finish).

Casement Window (Outward/Inward opening) with hinge System.

Frame (50 mm x 50mm)

Sash (Style and Rail) (62 mm x 34 mm)

Mullion (intermediate Section) (66mm x 50 mm)

‘T' Profile (one vertical length in between two shutters) (24mm x 34.5mm)

Glazing bead (12mm x 18mm)

Casement Window (With friction hinge and outward opening)

Casement Frame (67mm x 62mm)

Casement Window Sash/Mullion (67mm x75mm) (style, rail and intermediate section)

Casement Glazing bead (35mm x 18 mm)

Sliding Window (Two Track, 2/4 Shutters)

Two Track Sliding Frame (67mm x 52mm)

Sliding window Sash (60mm x 44mm)

Sliding Interlock for Window (one vertical length in each shutter)(45.5 mm x 28 mm)

Sliding Glazing bead (35 mm x 18 mm)

Sliding Door (Two Track, 2/4 Shutters)

Two Track Sliding Frame (67mm x 52mm)

Sliding Door Sash (80mm x 44mm)

Sliding Interlock for Door (one vertical length in each shutter) (45.5 mm x 28 mm)

Sliding Glazing bead (35 mm x 18 mm)

Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)

Casement window double panels with S.S. friction hinges (300 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window above 0.75 sqm upto 1.50 sqm).

Casement window double panels with top fixed with S.S. friction hinges (350 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 2.50 sqm).

Casement window single panel with S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 60 mm & sash 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 0.75 sqm.)

Casement window duble panel with S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 60 mm & sash 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.50 sqm.)

Casement cum fixed panel window having both and single casement panel, middle fixed panels and at top completely fixed ventilator with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series) frame 67 x 60 mm & sash 67 x 80 mm & mullion 67 x 80 all having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 3.00 sqm. Upto 5.00 sqm.)

Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm).

Casement door with top hung ventilator with 3D and S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ±. 0.2 mm and single glazing bead /double glazing bead of appropriate dimension. (Area of door upto 2.50 sqm).

Two track two panels sliding window made of frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)

Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Two track two panels sliding window made of frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension (Area of window above 1.75 sqm upto 2.50 sqm).

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/double glazing bead of appropriate dimension. (Area of window above 1.75 sqm).

Three track three panels sliding window made of frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ±0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

Two track two panels sliding window made of frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm).

Two track four panels sliding window made of frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 4.00 sqm upto 8.00 sqm).

Two track two panels sliding door made of frame 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 10.00 sqm).

Two track four panels sliding door made of frame 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 8.00 sqm upto10.00 sqm).

Three track three panels sliding door made of frame 116 x 45 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of door above 5.00 sqm)

Three track three panels sliding door with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of frame 116 x 45 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm)

24 to 25 mm thick plain solid PVC flush door shutter

28 to 30 mm thick plain solid PVC flush door shutter

1mm thick laminated sheet

0.12 mm thick laminated sheet

35mm thick including 4 nos. 100mm long, ISI marked heavy weight (2.5mm thick) Stainless steel butt hinges with necessary screws.

35mm thick including 3 nos. 100mm long, ISI marked heavy weight (2.5mm thick) Stainless steel butt hinges with necessary screws.

25mm thick (for cupboard) including 3 nos. 75mm long, ISI marked heavy weight (2.5mm thick) nickel plated bright finished M.S. piano hinges with necessary screws.

35mm thick including 4 nos. 100mm long, ISI marked heavy weight (2.5mm thick) Stainless steel butt hinges with necessary.

30mm thick including 3 nos. 100mm long, ISI marked heavy weight (2.5mm thick) Stainless steel butt hinges with necessary screws.

25mm thick including 3 nos. 100mm long, ISI marked heavy weight (2.5mm thick) Stainless steel butt hinges with necessary screws.

Acrylic Solid Surface sheet – Glacier white designer white

6 mm thick sheet

12 mm thick sheet

Acrylic Solid Surface sheet - Any Solid colours/Hospital use Medi Blue

6 mm thick sheet

12 mm thick sheet

Acrylic Solid Surface sheet - Any other

6 mm thick sheet

12 mm thick sheet

35 mm thick including 4 nos 100 mm long ISI marked heavy weight (2.5 mm thick) Stainless Steel butt hinges with necessary screws.

30 mm thick including 3 nos 100 mm long ISI marked heavy weight (2.5 mm thick) Stainless Steel butt hinges with necessary screws.

25 mm thick ISI marked heavy weight nickel plated bright finished M.S. piano hinges with screws.

35 mm thick including 4 nos 100 mm long ISI marked heavy weight (2.5 mm thick) Stainless Steel butt hinges with necessary screws.

30 mm thick including 3 nos 100 mm long ISI marked heavy weight (2.5 mm thick) Stainless Steel butt hinges with necessary screws

25 mm thick ISI marked heavy weight nickel plated bright finished M.S. piano hinges with screws.

35 mm thick including 4 nos 100 mm long ISI marked heavy weight (2.5 mm thick) Stainless Steel butt hinges with necessary screws.

30 mm thick including 3 nos 100 mm long ISI marked heavy weight (2.5 mm thick) Stainless Steel butt hinges with necessary screws.

35 mm thick including 4 nos 100 mm long ISI marked heavy weight (2.5 mm thick) Stainless Steel butt hinges with necessary screws.

30 mm thick including 3 nos 100 mm long ISI marked heavy weight (2.5 mm thick) Stainless Steel butt hinges with necessary screws.

35 mm thick including 4 nos 100 mm long ISI marked heavy weight (2.5 mm thick) Stainless Steel butt hinges with necessary screws.

32 mm thick including 3 nos 100 mm long ISI marked heavy weight (2.5 mm thick) Stainless Steel butt hinges with necessary screws.

25 mm thick ISI marked heavy weight nickel plated bright finished M.S. Piano hinges with screws.

35 mm thick including 4 nos. 100 mm long, ISI marked heavy weight (2.5mm thick) Stainless Steel butt hinges with necessary screws.

30 mm thick including 3 nos. 100 mm long, ISI marked heavy weight (2.5mm thick) Stainless Steel butt hinges with necessary screws.

25mm thick (for cupboard) including 3 nos. 75 mm long, ISI marked heavy weight (2.5mm thick) nickel plated bright finished M.S. piano hinges with necessary screws.

35 mm thick including 4 nos. 100 mm long, ISI marked heavy weight (2.5mm thick) Stainless Steel butt hinges with necessary screws.

30 mm thick including 3 nos. 100 mm long, ISI marked heavy weight (2.5mm thick) Stainless Steel butt hinges with necessary screws.

25mm thick (for cupboard) including 3 nos. 75 mm long, ISI marked heavy weight (2.5mm thick) nickel plated bright finished M.S. piano hinges with necessary screws.

35 mm thick including 4 nos. 100 mm long, ISI marked heavy weight (2.5mm thick) Stainless Steel butt hinges with necessary screws.

30 mm thick including 3 nos. 100 mm long, ISI marked heavy weight (2.5mm thick) Stainless Steel butt hinges with necessary screws.

25mm thick (for cupboard) including 3 nos. 75 mm long ISI marked heavy weight (2.5mm thick) nickel plated bright finished M.S. piano hinges with necessary screws.

35 mm thick including 4 nos. 100 mm long, ISI marked heavy weight (2.5mm thick) Stainless Steel butt hinges with necessary screws.

30 mm thick including 3 nos. 100 mm long, ISI marked heavy weight (2.5mm thick) Stainless Steel butt hinges with necessary screws.

25mm thick (for cupboard) including 3 nos. 75 mm long, ISI marked heavy weight (2.5mm thick) nickel plated bright finished M.S. piano hinges with necessary screws.

Providing and fixing factory made ISI marked glazed steel doors, windows and ventilators side /top /centre hung with beading and Z-section all members such as F7D, F4B, K11 B and K12 B and other tubular section member etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design (sectional weight of only steel members shall be measured for payment).

Providing and fixing L-iron or T-iron frames for doors, windows and ventilators of mild steel L-section or T-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

Providing and fixing pressed steel door frames made of 1.6 mm thick steel profile conforming to IS: 4351 manufactured from commercial mild steel sheet including hinges, jamb, lock jamb, M.S. pressed butt hinges, with mortar guards, lock strike-plate and shock absorbers as specified filling the frame with Cement Concrete 1:3:6 at site before fixing (cost of concrete to be paid separately) fixing with adjustable lugs (200 mm long & 1.0 mm thick) and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in- charge:

Fixing with adjustable lugs with split end tail to each jamb.

Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately).

Fixing with adjustable lugs with split end tail to each jamb.

Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately).

Fixing with adjustable lugs with split end tail to each jamb.

Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately).

Fixing with adjustable lugs with split end tail to each jamb.

Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately).

Fixing with adjustable lugs with split end tail to each jamb.

Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately).

Fixing with adjustable lugs with split end tail to each jamb.

Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately).

Providing and fixing M.S. Tubular frames and shutters or frames only or shutters only for doors, windows, ventilators and cupboard with any sections, made of 1.60 mm or 1.25 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size as per drawing, including fixing of necessary butt hinges, stays and screws and applying a priming coat of approved steel primer excluding cost of all fittings such as handles, tower bolts, sliding door bolts, latches etc. and panels.

Fixing with 15x3 mm lugs 10 cm. long embedded in cement concrete block 15x10x10 cm of Cement Concrete 1:3:6 (1 Cement : 3 sand : 6 graded stone aggregate 20 mm nominal size).

Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately).

Steel work in built up M.S. tubular section (round, square or rectangular hollow tubes etc.) trusses/frame work etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Hot finished welded type tubes

Hot finished seamless type tubes

Electric resistance or induction butt welded tubes.

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp of internal dia 140mm, 73mm height, top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3mm dia. round headed screws, one lock at the corners. Clamp shall be made of 16mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing and fixing bolts including nuts and washers complete.

Providing and fixing M.S. rivets of sizes in position.

Welding by gas or electric plant including transportation of plant at site etc. complete.

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In stringers, treads, landings etc. of stair cases including use of chequered plate wherever required, all complete.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying a priming coat of approved steel primer.

M.S. tube.

E.R.W. tubes.

Providing and fixing carbon steel galvanised (minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame, concrete/ masonry, etc. as per direction of Engineer-in-charge.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. (For payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

Providing and fixing fly proof wire gauze to windows, clerestory windows and doors with M.S. Flat 15x3mm and nuts and bolts complete.

Galvanised M.S. Wire gauze with 0.63mm dia wire and 1.4 mm aperture on both sides

Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides.

Providing and fixing glass panes/ steel sheet/ fibre sheet with putty and glazing clips in steel doors, windows, clerestory windows all complete.

With 4.0 mm thick glass panes

With 5.50 mm thick glass panes

With 1mm thick mild steel sheet i/c 10x10x1.6mm box beading.

With 2mm thick fibre reinforced polymer (FRP) sheet i/c 10x10x1.6mm box beading.

With 1mm thick Galvanised steel sheet i/c 10x10x1.6mm box beading.

With 4mm thick cement fibre board conforming to IS 14862:2000 of category type A grade i/c 10x10x1.6mm box beading.

With 6mm thick cement fibre board conforming to IS 14862:2000 of category type A grade i/c 10x10x1.6mm box beading.

With 8mm thick cement fibre board conforming to IS 14862:2000 of category type A grade i/c 10x10x1.6mm box beading.

Add extra for providing and fixing froasted glass instead of float glass.

With 4.0 mm thick glass panes.

With 5.5 mm thick glass panes.

Supplying at site:

R.C.C. Standards post/ struts/rails/ poles of mix 1:1.5:3 (1 cement : 1.5 sand : 3 graded stone aggregate 12.5 mm nominal size) with wooden plugs or 6mm bar nibs wherever required as per direction of Engineer-in-charge including fixing (cost of earth works in excavation, concrete works in foundation to be paid separately).

Angle iron post and strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete. (cost of earth work in excavation and concrete work in foundation to be paid separately)

Supplying at site -Welded steel wire fabric of required width having rectangular mesh painted with two or more coats of enamel paint of approved shade over a coat of primer (Priming painting to be paid for separately).

Supplying and fixing turn buckles and straining bolts for barbed wire fencing. (Labour rate only).

Fencing with R.C.C. post placed at required distance, embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post one side between the two posts fitted and fixed with G.I. staples on wooden plugs or G.I. binding wire tied to 6 mm bar nibs fixed while casting the post (cost of R.C.C. posts, struts, earth work and concrete to be paid for separately) with GI barbed wire.

Fencing with barbed G.I. wire angle iron post placed fitted to at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately):- Payment to be made per metre cost of total length of barbed wire used.

Fixing Welded steel wire fabric fencing with posts of specified material and of standard design placed and embedded in cement concrete blocks 45x45x60cm of mix 1:5:10 (1cement :5 sand :10 graded stone aggregate 40mm nominal size) every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and struts embedded in cement concrete blocks 70x45x50cm of the same mix, provided with welded steel wire fabric fixed between the posts fitted and fixed with G.I. staples on wooden plugs or tied to 6 mm bar nibs with G.I. binding wire (cost of posts, painting, earth work in excavation and cement concrete to be paid for separately). (Labour rate only) .

Providing and fixing G.I. or PVC coated G.I.wire chain link fabric fencing of required width and mesh size including strengthening with 2mm dia wire or nuts, bolts and washers as required complete with posts of specified material and of standard design placed and embedded in cement concrete blocks 45x45x60cm of mix 1:5:10 (1cement :5 sand :10 graded stone aggregate 40mm nominal size) every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and struts embedded in cement concrete blocks 70x45x50cm of the same mix, as per the direction of Engineer- in-charge. (Cost of post, painting earthwork & c.c. to be paid separately)

Made of G.I. wire.

Made of G.I. wire, PVC coated to achieve outer dia. not less than 5mm in required colour and shade.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I. wire of dia. 3mm including strengthening with 2mm dia. wire or nuts, bolts and washers as required complete, with posts of specified material and of standard design placed and embedded in cement concrete blocks 45x45x60cm of mix 1:5:10 (1cement :5 sand : 10 graded stone aggregate 40mm nominal size) every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and struts embedded in cement concrete blocks 70x45x50cm of the same mix, as per the direction of Engineer-in- Charge. (cost of post painting earth work & C.C. to be paid separately)

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length (total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sq mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately).

Providing and fixing of ISI marked insulated fire rated GI Sheet doors conforming to FD 120-PI classification of IS 3614:2021 with fire rating of 120 minutes integrity and 30 minutes insulation. The factory manufactured door frame and shutter assembly shall be made out of minimum 120 GSM coating as per IS: 277. Door and frame should be finished with powder coating in standard RAL shade finish having DFT of minimum 30 microns. The door should carry a minimum 500 Hrs of salt spray test. All accessories like hardware, vision panel, fire & smoke seal etc to be supplied by Fire door manufacturer only as per the guidelines laid down in IS 3614:2021.Every door must carry a label confirming to type of door & its fire rating. The Door frame shall be single rebate grooved profile of size minimum 125 mm x 75mm made out of 1.50mm minimum thick galvanized steel sheet. Frames shall be butt / mitered joint and field assembled with bolting system. Frames to have inbuilt grooved to accommodate Intumescent fire seal strip. Frames to have inbuilt grooved to accommodate Intumescent fire seal strip of size 10x4mm. All provisions should be mortised & provided with necessary inbuilt reinforcement to receive appropriate hardware. Frames should be provided with back plate bracket for anchor fastner with 8-10 mm dia and minimum 80 mm long HDG fasteners, with Polyamide sleeves (Payable in extra item) for installation of frame in finished plastered masonary wall opening. Note:- For grouting of Steel frames in masonary installations ;cement slurry of 1:3 ratio by civil contractor/fire rated PU foam or such fire rated material may be recommended except head member(Payable in extra item). Door leaf should be minimum 60mm thick fully flush double skin door. Door leaf must be manufactured from minimum 1.2mm thick galvanised steel sheet. The infill material shall be mineral wool of minimum density 96 kg/cum. All doors shall befactory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges should be interlocked with a bending radius of 1.4mm. For double leaf doors integrated astragals has to be provided on the meeting stile for both active and inactive leaf.The shutters shall be mounted to the frame with SS 304 grade ball bearing type hinges of size 100x 89x3 mm along with all suitable hardware (Payable in extra item).Vision lite size 185x285 (max area up to 0.06sqm) wherever applicable should be provided with single layered clear fire rated glass panes as per guidelines laid down under IS 3614 : 2021 vide clause no. 7.2.7 table no. 2 with a clip on arrangement. The glass will be provided with fire rated ceramic tape of min. 2 mm thickness with min. 15mm width al around on either face. Every Glass pane must carry a permanent marking of its glass manufacturer

Providing and fixing of factory make air tight casement windows made of roll formed galvanized pre-painted steel with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns Including filling the gap upto 5 mm depth and 5 mm width in between steel frame and adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

Openable window

Fixed windows

Providing and fixing of factory make single rebate openable/fixed windows made of roll formed galvanized pre- pained steel with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick) heavy duty pivot hinges per shutter and window fitted without glazing including 10mm square bars welded to 6x12mm flat at a distance 150mm c/c (pitch) etc. Including filling the gap upto 5 mm depth and 5 mm width in between steel frame and adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in- charge complete.

Openable single rebate window

Fixed single rebate window

Providing and fixing of factory make double rebate windows made of roll formed galvanized pre-painted steel with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick, fitted using EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing windows in the concrete/masonry wall by means of self- expanding screws, including 10mm Square bars welded to 6x12mm flat at a distance 150mm c/c (pitch) etc. Including filling the gap upto 5 mm depth and 5 mm width in between steel frame and adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in- charge complete..

Openable double rebate window

Fixed double rebate window

Providing and fixing of factory make fixed louvers fabricated from roll formed sections made of galvanized pre-painted steel with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick, colour coated/powder coated Including filling the gap upto 5 mm depth and 5 mm width in between steel frame and adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in- charge complete. (glazing shall be paid separately as per SOR rate)

Providing and fixing of factory make pre painted steel sliding window 2 track-2 panel sliding window fabricated from roll formed sections made of galvanized steel with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns The above frames should be fixed to the concrete/masonry walls by means of self-expanding screws. Including filling the gap upto 5 mm depth and 5 mm width in between steel frame and adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

Providing and fixing pre painted steel sliding window 3 fabricated from Roll formed sections made of galvanized Steel with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns The above frames should be fixed to the concrete/masonry walls by means of self-expanding screws. Including filling the gap upto 5 mm depth and 5 mm width in between steel frame and adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

Marble chips skirting (upto 30 cm height) 18 mm thick with under layer 12 mm thick in cement plaster 1:3 (1 cement : 3 sand) : rubbed and polished to granolithic finish, top layer 6 mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from smallest to 4 mm nominal size laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 4:7 (4 cement marble powder mix :7 marble chips) by volume :

Extra for laying terrazo flooring on staircase treads not exceeding 30 cm in width including cost of forming, nosing etc.

Providing and fixing glass strips 40 mm wide and 4 mm thick in joints of terrazo/ cement concrete floors.

18 mm thick crazy marble stone white, black or as specified marble stone flooring, including filling the gaps with light shade pigment with white cement marble powder mixture (3 parts of white cement : 1 part of marble powder) by weight in proportion of 4:7 (4 cement marble powder mix : 7 white, black or white and black marble chips of sizes from 1mm to 4mm nominal size by volume), with under layer 25mm thick cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 12.5 mm nominal size), including rubbing, polishing and cement slurry etc.complete .

Precast terrazo tiles 22mm thick with graded marble chips of size upto12mm, laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 sand) :

Light shade using white cement.

Medium shade using 50%white cement and 50% ordinary cement.

Dark shade using ordinary cement.

Ordinary cement without any pigment.

Extra if terrazo tiles are laid in treads of steps not exceeding 30 cm in width.

Precast terrazo tiles 22 mm thick with graded marble chips of sizes upto 12 mm in skirting and risers of steps not exceeding 30 cm in height on 12 mm thick cement plaster 1:3 (1 cement : 3 sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete with tiles of :

Light shade pigment using white cement.

Medium shades pigment using 50% white cement and 50% ordinary cement.

Dark shade pigment using ordinary cement.

Ordinary cement without any pigment.

Chequeredterrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete on 20 mm thick bed of cement mortar 1:4 (1 cement :4 sand) :

Light shade pigment using white cement.

Medium shade pigment using 50% white cement, 50% ordinary cement.

Dark shade pigment using ordinary cement.

Ordinary cement without any pigment.

Chequered precast cement concrete tiles any finish, any size 22 mm thick IS:13810-1993 ISI mark in footpath and courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles, 15mm thick screed bad in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

Light shade pigment using white cement.

Medium shade pigment using 50% white cement 50% Grey cement.

Dark shade pigment using ordinary cement.

Ordinary cement without any pigment.

Marble stone flooring with 18 mm thick marble stone (sample of marble shall be approved by Engineer-in-charge) laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 sandand grey cement slurry, joints treated with white cement mixed with pigment to match colour of stone including rubbing and polishing complete with : (area of slabs over 0.5 sqm)

Makrana white second quality.

Raj Nagar plain.

Agaria White/Morgarh

Katni marble

Black Zebra.

Udaipur / Baroda green marble

Pink plain marble.

Jaisalmer Yellow

Marble stone 18 mm thick in riser of step, skirting, dado and pillar laid on 12 mm average thick cement mortar 1:3 (1 cement: 3 sand and laid with white cement slurry) joints treated with white cement mixed with pigment to match the shade of the slab i/c rubbing and polishing complete. (area of slab over0.50sqm.)

Makrana white second quality.

Raj Nagar plain.

Agaria White/Morgarh

Katni marble

Black Zebra.

Udaipur / Baroda green marble

Pink plain marble.

Jaisalmer Yellow

Marble work gang saw cut (polished and machine cut) of thickness 18 mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement: 3 sand), including pointing with white cement mortar 1:2 (1 white cement: 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately). (Area of slabs over 0.50 sqm.)

Makrana white second quality.

Raj Nagar plain.

Agaria White/Morgarh

Katni marble

Black Zebra.

Udaipur / Baroda green marble

Pink plain marble.

Jaisalmer Yellow

Providing and fixing 18mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish wherever required etc. complete at all levels. Samples approved by Engineer-in- Charge.

Raj Nagar plain/White Marble/Udaipur Green Marble /Zebra black

Granite fine grained dark crystal of other colours and various patterns

Granite coarse grained light black/ light red/white with crystal of other colours and various patterns

Granite grey/pink/brown with various patterns

Cuddpah stone

Extra for prefinished nosing to treads of steps of marble stone.

Extra for marble stone flooring in treads of steps and risers using single length upto 2.00 metre.

Extra for prefinished grooves to treads of steps of granite stone

Providing and laying machine cut, mirror polished, Italian Marble stone (18 mm thick Italian Marble stone slab, Perlato, Rosso erona, Fire Red or Dark Emperadore etc.)work in flooring laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement: 4 sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry mixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Providing and fixing machine cut, mirror / eggshell polished , Marble stone work 18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire Red or Dark Emperadore etc. for wall lining (veneer work) including dado, skirting, risers of steps etc. thick cement mortar 1:3 (1 cement : 3 sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge.

Italian marble flooring in required design and patterns

Providing and laying machine cut, mirror polished Italian Marble stone 18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire Red or Dark Emperadoreetc flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of different colours, shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Note – This item shall be executed only after the prior approval of Chief Engineer.

Granite work gang saw cut (polished and machine cut) of thickness 18mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement: 3 sand) including pointing with white cement mortar 1:2 (1 white cement: 2 marble dust) with an admixture of pigment to match the marble shade: (To be secured to the backing by means of cramps, which shall be paid for separately).

Area of slab over 0.50 sqm

Fine grained granite dark Black/dark Red/ White or equivalent with self design/ pattern/crystals of other colors of glitter

Coarse grained granite light Black/light Red/ off White or equivalent with self design/ pattern/crystals of other colors of glitter

Gray/Pink/Brown or equivalent with various patterns

Area of slab upto 0.50 sqm

Fine grained granite dark Black/dark Red/ White or equivalent with self design/ pattern/crystals of other colors of glitter

Coarse grained granite dark Black/dark Red/ White or equivalent with self design/ pattern/crystals of other colors of glitter

Gray/Pink/Brown or equivalent with various patterns

Providing and laying gang saw cut 18 mm thick, mirror polished premoulded (wherever required) and pre polished machine cut granite stonework in flooring of required size shape of approved shade, color and texture in flooring laid over 20 mm thick base of cement mortar 1:4 (1 Cement: 4 sand) including grouting the joints with white cement mixed with matching pigments epoxy touch ups etc. complete as per direction of Engineer-in-Charge.

Area of slab over 0.50 sqm

Fine grained granite dark Black/dark Red/ White or equivalent with self design/ pattern/crystals of other colors of glitter

Coarse grained granite light Black/light Red/ off White or equivalent with self design/ pattern/crystals of other colors of glitter

Gray/Pink/Brown or equivalent with various patterns

Area of slab upto 0.50 sqm

Fine grained granite dark Black/dark Red/ White or equivalent with self design/ pattern/crystals of other colors of glitter

Coarsegrained granite dark Black/dark Red/ White or equivalent with self design/ pattern/crystals of other colors of glitter

Gray/Pink/Brown or equivalent with various patterns

Providing and laying gang saw cut 30 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement: 4 sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge. (area of slab more than 0.50 sqm)

Fine grained granite dark Black/dark Red/ White or equivalent with self design/ pattern/crystals of other colors of glitter

Coarse grained granite light Black/light Red/ off White or equivalent with self design/ pattern/crystals of other colors of glitter

Gray/Pink/Brown or equivalent with various patterns

Deduct for not polishing granite flooring (item no 11.29 & 11.30)

Providing and laying Granite stone flooring in required design and patterns in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry admixed with pigment of matching shade including rubbing, curing and polishing and as directed by the Engineer-in-Charge Granite stone slab Dark Black. Dark Red, White or equivalent,

Flamed Finish Polish

Leather Finish Polish

Granite stone work 18mm thick of any colour in riser of steps, skirting, dado and pillars laid on 12 mm average thick cement mortar 1:3 (1 cement:3 sand) and jointed with white cement slurry mixed with pigment to match the shade of slab.

Providing and fixing 10x10x7.50 cm Granite stone block hand cut andchisel dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1cement:4 sand) with joints 10mm wide filled with same mortar mixed with matching pigment including ruled pointing etc. complete as per direction of engineer-in charge.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 sand) 25 mm thick.(Area of slab to be over 0.25 sqm)

Deduction for using 20 mm thick slab instead of 25 mm thick slab of kota stone in item no 11.35

Kota stone slabs in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

20 mm thick

Kota stone slab (area less than 0.5 sqm) rough chiseled dressed average 40 mm thick flooring for parking and open area of thickness over 20 mm (average) thick base laid over and jointed with grey cement slurry complete with base of cement mortar 1:4 (1 Cement : 4 Sand)

Providing edge moulding to 18mm thick marble stone counters, Vanities, window sills etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Marble work

Granite work.

Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete.

Extra for providing opening of required size and shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Mirror polishing on marble work/Granite work/stone work wherever required to give high gloss finish complete.

Fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1cement : 5 sand) with joints finished flush.

Red sand stone

White sand stone

Grey lime stone

Kota stone

40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 sand) including pointing with cement mortar 1:2 (1 cement : 2 sand) with an admixture of pigment to match the shade of stone.

Red sand stone

White sand stone

40 mm thick machine rubbed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement :5 sand) with joints 3mm thick, side buttered with cement mortar 1:2 (1 cement : 2 sand) mixed with pigment to match the shade of stone and pointing with same mortar

Red sand stone

White sand stone

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

Extra for Kota stone/ sand stone in treads of steps and risers using single length upto 1.05 metre.

Providing and laying Ceramic glazed floor tiles 300x300 mm or more (having thickness 6 to 7mm) of 1st quality conforming to IS : 15622 of approved make in any colours and shade laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 sand) including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing Ceramic glazed wall tiles 300x450 mm or more (having thickness 6 to 7 mm) of 1st quality conforming to IS: 15622 of approved make in all Colours& shades, except burgundy, bottle green, black laid on 12mm thick bed of Cement Mortar 1:3 (1 Cement: 3 sand)preprad same day when mortar is still green jointed with grey cement slurry @3.3 kg per sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying rectified Glazed Ceramic floor tiles 300x300 mm or more (having thickness 9 to 10mm) of 1st quality conforming to IS : 15622 of approved make in all colours white, ivory, grey, fume red brown laid on 20mm thick cement mortar 1:4 (1 Cement : 4 sand) including grouting the joints with white cement and matching pigments etc., complete.

Providing and laying rectified Glazed Ceramic wall tiles 300x450 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in all colours white, ivory, grey, fume red brown laid on 12 mm thick cement mortar 1:3 (1 Cement : 3 sand) including grouting the joints with white cement and matching pigments etc., complete.

Providing and laying Antiskid floor tiles of any sizes, 12 mm thickness with water absorption less than 0.08% and conforming to IS:15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 sand) including grouting the joints with white cement with matching pigments etc., complete.

Deduct for not grouting the joints with white cement and matching pigment in the items of fixing of vitrified tiles.

Deduct for not using 20mm thick cement mortar 1:4 (1 cement: 4 sand) bedding in laying of floor tiles.

Fixing glazed/ Ceramic/Rectified/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness.

Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having water absorption less than 0.05% and conforming to IS: 15622 of approved make in all colours and shades for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1cement : 4 sand) in all shapes and patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Providing and fixing Glass mosaic tiles at finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design, fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge:

Providing and laying 500x500x40mm thick Turf paver on 150mm thick sub grade of compacted bed of 20mm nominal size stone aggregate and base course with 50mm thick sand and filling joints with sand including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer- in-charge.

Providing and fixing 10mm thick acid and/ or alkali resistant tiles of approved make and colour using acid and/ or alkali resisting mortar bedding and joints filled with acid and/ or alkali resisting cement as per IS : 4457 complete as per the direction of Engineer-in- Charge.

8 mm thick.stones Tile work in skirting, risers of steps and dado (upto 2 m height) over 12 mm thick bed of cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing in white cement mixed with pigment of matching shade complete.

Marble tiles (polished) Raj Nagar.

Granite tile of any colour /shade

Providing and fixing cramps of required size and shape in RCC/ CC /Stone/ Brick masonry backing with cement mortar 1:2 ( 1 cement :2 sand) including drilling necessary hole in stones and embedding the cramp in the hole (fastener to be paid separately).

Gunmetal cramps.

Stainless steel cramps.

Providing and fixing expansion hold fasteners of wedge expansion type on C.C. / R.C.C./ Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete.

Fastener with threaded dia 6 mm.

Fastener with threaded dia 10 mm.

Fastener with threaded dia 12 mm.

Providing and fixing stone slab table rubbed on both faces edges rounded and polished of size as required and 1.8 cm thick fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement: 2 sand: 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in- charge and finished smooth.

White Agaria Marble Stone.

Granite Stone of approved shade.

Providing and fixing removable raised/false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame work and and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer- in-charge. All specification must be printed on the side of the panel to ensure the quality of the product.

300 mm Finished Floor Height (FFH)

450 mm Finished Floor Height (FFH).

Providing and laying factory made machine pressed precast cement concrete interlocking paver block of any shape and size conforming to IS:15658- 2006 and ISI marked of 60 mm thickness, M-30 grade with grey cement and pigment all as specified. Made by block making machine with strong vibratory compaction, laid in required colour and pattern over and including 50mm thick compacted bed of stone dust, filling the joints with sand etc. all complete as per the direction of Engineer-in-Charge.

Providing Epoxy flooring self leveling type on strong base in desired colour/design as approved by Engineer-in-Charge. Resin for epoxy is to be of floor grade type i/c appropriate hardner and filler material. with 5 year defect liability period (This item is to be used only for operation theaters in hospitals)

1 mm thick

2 mm thick

3 mm thick

Providing and fixing acoustic PVC (Poly Vinyl Flooring) EN (European Standard) over fiberglass mat PVC foam backing (EN 14904), total thickness is 3.25mm (EN 428/EN 427), wear layer is 0.85 mm thick (EN 429), anti-bacterial and anti-fungus surface treatment , chemical resistance test qualified (EN-423)-high resistance, thermal and underfloor heating test qualified (EN12524) - all vinyl sheets must be linked crosswise with a continuous copper strip and finally connected to earth for grounding electrostatic electrical charges. Suitable and slip resistant. Recommended to use in area like Lecturer room, Conference room, Kids area, School, colleges, Residential and all commercial official scope etc.

Providing and fixing 2 mm thick heterogeneous PVC (poly vinyl flooring) EN (European Standard) with wear layer is 0.55mm thick of PVC, total weight is 2300 g/m2 approx. PUR (polyurethane reinforced), residual indentation approx.0.05 mm, castor wheel test qualified, dimensional stability ≤0.10%, static electrical charge .The floor finish should termite free at the room perimeter passing over a concealed cove forming and continuing up on the wall upto100mm. Recommended to use in area like Patient rooms , Doctor room Lecturer room, Kids area, School, Colleges, Residential and all commercial official scope etc.

Providing and fixing 8mm and above thick laminated (wooden flooring) of AC4 and above grade product of approved made out of core high density fibre board (HDF), surface layer shall be high preasure laminated treated for abrasion, scratch, moisture protection, flame protection U.V resistant, layer of acrylic resin, aluminium oxide or similer layer having above properties, backing under layer on min 2 mm thickness shall provide as sound absorbent and moisture protection layer, The seamless impregenated decorative layer of specified size, design, colour and pettern, all bonded together under high temperature and pressure with eco-friendly. The material shall be applicable warranty formaldehyde free, eco- friendly and fully recyclable (eco-freindly) and matching shed and excluding quantity of skirting and profile.

Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar, 1:6 (1 cement : 6 sand) including filling the joints with same mortar, with common burntclay non modular bricks

100 mm thick

200mm thick

Providing and laying factory made chamfered edge Cement Concrete paver blocks of required colour strength, thickness pattern, surface texture (smooth/rough) and size/shape, conforming to 15658-2006 IS marked made by table vibratory method using PU mould, laid in required colour and pattern over 0.30 mm with courtyards, porch with M 15 cement concrete in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per manufacturer's specifications and direction of Engineer-in-Charge.

80 mm thick C.C. paver block of M-35 grade

60 mm thick C.C. paver block of M-35 grade

60 mm thick C.C. paver block of M-30 grade

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in- Charge).

Providing and fixing at or near ground level factory made RCC pavement slab of M-30 grade of size 450x450x50 mm, including reinforcement with 6 mm dia M.S. bars 4 nos on each side(top & bottom), including setting in position in footpath to the required level and line over a bed of 20 mm average thick cement mortar 1:5 (1 cement : 5 sand), having joint thickness not more than 5mm except on curve, including filling of joints with same cement mortar and making grooves etc. complete as per direction of Engineer-in-Charge.

Providing and fixing 16mm thick gang saw cut mirror polished premoulded and prepolished machine cut Granite of approved shade, colour and texture of Granite Door frame. in cement mortar 1:3 (1 cement :3 sand) Including rubbing, curing, moulding and polishing edges to give high glossy finish and drilling of hole for fixing stainless steel hings, aldrop, towerboltetc complete at all levels as per instruction of Engineer-in-Charge.

Granite Door frame for 100mm thick wall Thickness.

Granite Door frame for 200mm thick wall Thickness.

Providing and laying vitrified floor tiles (without soluble salt) or printed (with soluble salt) Nano polished (Glossy finish) in different sizes with water absorption less than 0.05% and conforming to IS:15622 of approved make in all colours& shades, 1st quality/ premium quality in flooring laid on 20mm thick cement mortar 1:4 (1cement :4sand) including grouting the joints with white cement and matching pigments etc. complete

Plain ivory light shade : Size 600X600mm thickness 9-10mm

Dark shade (terracotta) : Size 600X600mm thickness 9-10mm

Providing and laying vitrified floor tiles (without soluble salt) or printed (with soluble salt) Nano polished (Glossy finish) in different sizes with water absorption less than 0.05% and conforming to IS:15622 of approved make in all colours& shades, 1st quality/ premium quality in skirting laid on 12mm thick cement mortar 1:4(1cement :4sand) including grouting the joints with white cement and matching pigments etc. complete

Providing and laying vitrified floor tiles Multi/Double charged (Minimum top layer thickness 2.0mm) Neno Polished self design, in different size with water absorption less than 0.05% and conforming to IS:15622 of approved make in all colours& shades, quality/ premium quality in flooring laid on 12mm thick cement mortar 1:4(1cement :4sand) including grouting the joints with white cement and matching pigments etc. complete

Providing and laying vitrified floor tiles Multi/Double charged (Minimum top layer thickness 2.0mm) Neno Polished self design, in different size with water absorption less than 0.05% and conforming to IS:15622 of approved make in all colours& shades, 1st quality/ premium quality in skirting laid on 12mm thick cement mortar 1:4(1cement :4sand) including grouting the joints with white cement and matching pigments etc. complete

Providing and laying vitrified floor-tiles Full Body Design Homogenous Body matt/rustic finish in different size with water absorption less than 0.05% and conforming to IS:15622 of approved make in all colours& shades, 1st quality/ premium quality in flooring laid on 20mm thick cement mortar 1:4(1cement :4sand) including grouting the joints with white cement and matching pigments etc. complete

Providing and laying vitrified floor-tiles Full Body Design Homogenous Body matt/rustic finish in different size with water absorption less than 0.05% and conforming to IS:15622 of approved make in all colours& shades, 1st quality/ premium quality in skirting, riser laid on 12mm thick cement mortar 1:4(1cement :4sand) including grouting the joints with white cement and matching pigments etc. complete

Providing and laying digital print random design(PGVT)/(GVT) vitrified tiles in different sizes with water absorption less than 0.05% and conforming to IS:15622 of approved make in all colours& shades, 1st quality/ premium quality including grouting the joints with white cement and matching pigments etc. complete

Size 800X1600 mm thickness 11-12mm

Size 1000X1000 mm thickness 11-12mm

Size 1200X1800 mm thickness 11-12mm

Size 1200X2400 mm thickness 11-12mm

Size 300X600 mm thickness 9-10 mm

Size 300X600 mm thickness 9-10 mm

Providing and laying digital print random design(PGVT)/(GVT) vitrified tiles in different sizes with water absorption less than 0.05% and conforming to IS:15622 of approved make in all colours& shades, 1st quality / premium in skirting, riser laid our 12mm thick cement mortar 113 including grouting the joints with white cement and matching pigments etc. complete

Granite work gang saw cut (polished machine cut) of thickness 12 mm for wall lining, skirting, risers of steps and dado (veneer work), back filling with a grout of average 12 mm thick in cement mortar 1:3 (1 Cement: 3 sand) including pointing with white cement mortar 1:2 (1 white cement: 2 marble dust) with an admixture of pigment to match the marble shade: (To be secured to the beaching by means of cramps, which shall be paid for separately).

Providing and fixing laminated (engineered wooden flooring) of suitable thickness 10-14 mm of suitable grade category product of approved made out of core high density fibre board (HDF) &other component it treated for abrasion ,scratch ,moisture protection, flame protection,U.V resistant. backing with eco- friendly resins specified by the manufacturer .The material shall be applicable warranty formaldehyde free, eco friendly, highly recommended for high traffic area and fully recyclable and matching shed and excluding quantity of skirting and profile .

Providing and fixing single layer homogeneous (solid wooden flooring) of suitable thickness 14 - 18 mm of suitable grade category product of scratch protection, moisture protection, flame protection U.V. resistant, backing under layer on min 2 mm thickness The material shall be applicable warranty formaldehyde free, eco friendly ,highly recommended for high traffic area and fully recyclable and matching shade and excluding quantity of skirting and profile.

Providing and fixing tuffed 1/10” loop pile (carpet tile / Carpet). EN (Euorpean Standard) size 50cm x 50cm /roll Size of total thickness 5.5 mm and above with total mass of 4100g/m2approx and with polyester fleece primary backing with standard dimensional stability with impact sound / noise reduction and recommended for high traffic acoustical area.

Providing and fixing spc (stone plastic composite) virgin pvc water resistant proof vinyl flooring with a thickness between 4 to 8mmuv coated layer with a wear layer of 0.3 to 0.80mm with a SPC core layer of 2.00 to 5.00 mm with a SOP of heat resistant, voc free, easy to cut, anti microbial protection in the form of tiles, planks helpful in environmental of profection health.

Providing and laying pre mirror polished/ pre polished fine grain machine cut sand stone tile flooring 20mm thick (hardness should not be less than 7 and water absorption should not be more than 0.3%) of required size and shape of approved shade, flooring in plazas open staircase and similar locations, laid over 20 mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joint with white cement mix with matching pigment etc. complete as per direction of Engineer-in-Charge.

Providing and laying pre mirror polished/ pre polished fine grain machine cut sand stone slab flooring 20mm thick (hardness should not be less than 7 and water absorption should not be more than 0.3%) of required size of area more then .50 sqm and shape of approved shade, flooring in plazas open staircase and similar locations, laid over 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joint with cement mix matching pigment etc. complete as per direction of Engineer -in-Charge.

Extra for circular cutting in reinforced by organic fibres and/or inorganic synthetic fibres cement corrugated/ semi corrugated 6 mm thick sheet roofing for making openings of area exceeding 40 square decimeter.

Extra for providing and fixing wind ties of 40x 6 mm flat iron section.

Providing and fixing ridges and hips in fibre cement reinforced by organic fibres and/or inorganic synthetic fibres roofing with suitable fixing accessories or self drilling fastener and EPDM washer etc. complete.

Providing and fixing fibre cement reinforced by organic fibres and/or inorganic synthetic fibres roofing accessories in all colours with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers or with self drilling fastener and EPDM washer etc. complete:

Corrugated apron pieces

Eave's filler pieces

North light curves

ventilator curves

Barge boards

Ridge finials

Special north light curves

S type louvers

Providing flat iron brackets 50x3mm size with necessary bolts, nuts washers etc. for fixing G.S. sheets gutters with purlins.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm + 0.05 %, total coated thickness with zinc coating 120 gsm as per IS:277 in 240 mpa steel grade, 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self-drilling /self-tapping screws of size (5.5x 55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + 0.05 % total coated thickness, Zinc coating 120gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self-drilling/ self- tapping screws complete :

Ridges plain (500 - 600mm).

Flashings/ Aprons.( Upto 600 mm)

North light curves.

Barge board (Upto 300 mm)

Crimp curve

Gutter. (600 mm over all girth)

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.

2mm thick corrugated (2.5" or 4.2" or 6") or step-down (2"or 3"or 6") as specified.

2mm thick flat.

Providing and Fixing of sky lights consisting of Multi cell/tight cell Polycarbonate Panel System of approved colour, 16 mm thick (minimum) having uniform in color with an integral Tight-Cell core constructed not to exceed 4mmx4mm in a cross section, involved such as bolts nuts and screws etc. and labour for cutting bending to required profile, necessary scaffolding, hoisting in position etc. for proper completion of the work etc. complete as per specification drawings and direction of Engineer in charge. Finished surface area of roofing fixed over steel tubular structure shall be measured for payment. MS tabular frame work shall be measured separately for payment.

10mm thick

16mm thick

Providing sand stone slab 40 to 50 mm thick for roofing and laying them in cement mortar 1 : 4 (1 cement : 4 sand) over wooden karries or R.C.C. battens or structural steel sections (Karries or battens or structural steel sections to be paid separately) including pointing the ceiling joints with cement mortar 1:3 (1 cement : 3 sand ) complete :

Red sand stone slab

White sand stone slab :

Painting top of roofs with residual type petroleum bitumen of grade VG 10 of approved quality @ 17kg per 10 sqm impregnated with a coat of sand at 60 cum per 10sqm including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete :

Providing and applying two coats of High Albedo paint having minimum Solar Reflective Index (SRI) 108 (with solar reflectance and thermal emittance tested as per ASTM) C 1549 and ASTM C 1371 respectively), VOC less than 10 cc/gm. The coating thickness and the methodology of application shall be strictly as per manufacturer's specifications and as approved by engineer In charge. Surface preparation includes cleaning with metal wire brush to remove all dust, fungus etc., and washing with water all complete. The contractor shall give guarantee for the performance of SRI and also the durability of coating, all complete as per direction of Engineer-in-charge.

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection >0.70 and initial emittance >0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 sand) and grouting the joints with mix of white cement and marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

Providing and laying pressed clay tiles (as per approved pattern 20 mm nominal thickness and of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 sand) mixed with 2% integral water proofing compound laid over a bed of 20 mm thick cement mortar 1:4 (1 cement : 4 sand) and finished neat complete.

Providing and fixing on roof pressed clay tile (Mangalore tile) 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately)

Providing and laying on roof pressed clay tile ridge (Mangalore tile) of 20mm thickness of approved pattern on steel frame work complete (steel frame work to be paid separately)

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 sand : 4 stone aggregate 10mm and down grade) including finishing with cement mortar 1:3 (1 cement : 3 sand) as per standard design : In 75x75mm deep chase

Making khurras 45x45 cm (sunk area) with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400micron, finished with 12mm cement plaster 1:3 (1 cement : 3 sand) and a coat of neat cement rounding the edge and making and finishing the outlet complete so as to receive rain water/ spillage water on roof in a sunk area and completely rain out in a near perfect strain meter motion into rain water pipe.

Providing and fixing M.S. holder bat clamps of approved design to C.I. Or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10cm of Cement Concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc.

100 mm diameter

150 mm diameter

Providing and fixing ISI marked sand cast iron rain water pipes.

100 mm dia minimum wall thickness 5mm

150 mm dia minimum wall thickness 5mm

Providing lead caulked joints to sand cast iron rain water pipes and fittings :

100 mm dia. Pipe

150 mm dia. Pipe

Providing, fixing and embedding sand cast iron accessories for rain water pipes in the masonry surrounded with 12 mm thick cement mortar of the same mix, as that of masonry (lead caulking will be paid for separately) :

Sand cast iron bend :

100 mm diameter

150 mm diameter

Sand cast iron plain shoes :

100 mm diameter

150 mm diameter

Providing and fixing on wall face Rigid Unplasticised rigid PVC (upvc) Single socketed rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

75 mm diameter (minimum wall thickness 1.8mm)

110 mm diameter (minimum wall thickness 2.2mm)

Providing and fixing on wall face Unplasticised - UPVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

Coupler

75 mm (minimum wall thickness 1.8mm)

110 mm (minimum wall thickness 2.2mm)

Single push fit Coupler :

75 mm (minimum wall thickness 1.8mm)

110 mm (minimum wall thickness 2.2mm)

Single tee with door

75x75x75 mm (minimum wall thickness 1.8mm)

110x110x110 mm (minimum wall thickness 2.2mm)

Single tee without door

75x75x75 mm (minimum wall thickness 1.8mm)

110x110x110 mm (minimum wall thickness 2.2mm)

75 mm bend (minimum wall thickness 1.8mm)

110 mm bend (minimum wall thickness 2.2mm)

Shoe (Plain)

75 mm Shoe (minimum wall thickness 1.8mm)

110 mm Shoe (minimum wall thickness 2.2mm)

Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

75 mm (minimum wall thickness 1.8mm)

110 mm (minimum wall thickness 2.2mm)

Providing and fixing to the inlet mouth of rain water pipe fixing cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing to the inlet mouth of rain water pipe PTMT (an Engineering Thermoplastic) grating square (Slit) 150 mm square with a height of 8 mm and weighing not less than 100 gms.

Providing and fixing 100 mm/110 mm diameter and 60 cm long rain water spout in cement mortar 1:4 (1 cement : 4 sand)

Stone ware spout

Upvc spout (Pipe dia.110 mm)

Providing and fixing of self-supported mechanically seamed roofing system, made of high quality steel, having 340 MPA yield strength, pre coated galvalume sheet as per ASTM A 792 M of base metal thickness from 0.8 mm to 1.6mm (tolerance ± 0.02mm). High grade steel sheet should have 55% aluminum and 45% zinc coating by hot-dip process of minimum 25 micron The rate includes supplying, fixing, loading unloading, hire charges of all plants machineries, anchors, fasteners, washers, bolts, epoxy, paint and all wastage etc. complete. Accessories and fixtures like hangers/clamps for installation of lighting /fixtures /utility/ duct as per requirement and ventilators, skylight can also be provided at crown/ridge by making cuts into the panels which is to be paid separately. This item shall be executed only by the agency which has all required manufacturing machineries and necessary expertise.

Base metal thickness 0.8mm up to span 15 meter

Base metal thickness 0.9mm , up to span 18 meter

Base metal thickness 1.0 mm, up to span 21 meter

Base metal thickness 1.1 mm, up to span 23 meter

Base metal thickness 1.2mm, up to span 25meter

Base metal thickness 1.3 mm, up to span 27 meter

Base metal thickness 1.4mm, up to span 29meter

Base metal thickness 1.5 mm, up to span 31 meter

Base metal thickness 1.6 mm, up to span 33 meter

Providing and fixing galvalume 1.0 mm thick clamps/hangers of size 75X140mm with saddle of 50mm dia, riveted at one side and nut and bolt at other side, to self-supported roofing system by mechanical seaming to suspend light fixture/cable stay/false ceiling/duct etc., at their location which should be planned earlier by engineer-in-charge. Clamps shall be fixed during seaming of panels.

Providing and fixing advanced type hurricane turbo ventilator to self- supporting roof having neck dia 600mm made of aluminum having 24 nos vertical vanes made of aluminum sheet. Ventilator should be fixed on 1 to 2mm thick G.I. ring which shall be fixed on 2mm thick polycarbonate sheet. Polycarbonate sheet shall have foam tap or rubber gasket under and over it and fixed by 1 to 2 mm thick aluminum angle 25X25mm with self- tapping screw to panels. All joints shall be sealed by silicon. Rates i/c of all material, labour fittings screw, rings, foam tap, aluminum angles etc. complete. Deduction shall not be made for cutting area of self-supported roof.

Providing and fixing of 2mm thick polycarbonate sheet to self-supported roofing system. The sheet shall have tensile strength and elongation as per ASTM D 638, refractive index as per ASTM D 592, light transmission as per ASTM D 1003 and specific gravity as per STM D 792. Polycarbonate sheet shall have foam tap or rubber gasket under and over it and fixed by 1 to 2 mm thick aluminum angle 25X25mm with self- tapping screw to panels. All joints shall be sealed by silicon. Rates include of all material, labour, fittings, screw, foam tap, aluminum angles etc. complete. Deduction shall not be made for cutting area of self-supported roof.

Supply, fabrication and erection of three-dimensional space frame steel structure consisting of support node, primary space frame members, space notes nodes, bolts, sleeves (nut), purlin stool, purlin etc. to support roof sheet in plain or curved shape. (Approximate zinc coating thickness 77 Microns) and shall not be less than 400 g/sqm (Approximate zinc coating thickness 56 microns). Bolts, sleeves and cones shall be electro-galvanized to ASTM B 633 Type 2, SC3. Shop drawings along with structural design analysis shall be provided by the manufacturer for approval of the engineer in charge. Rate shall include cost of design, all material, all lifts, labour, transport, storage, machines, tools and plants, wastages, erection and installation at site all necessary scaffolding etc. necessary to provide finished product but excluding cost of erection/construction of support shaft and roof sheet.

Providing and fixing roofing consist of 0.8 mm thick galvanized steel deck sheet confirming to IS 277:1992 used as permanent shuttering over which MS wire mesh 3mm laid at 100x100 mm grid including edge trim covered with concrete. This metal deck will be supported on structural steel beam with shear studs. (Structural steel like Beam, column, joists etc. & concrete of different grade as per design will be paid separately).

Providing and fixing in position roof tile under lay using 12mm thick(minimum) Moisture/fire Resistance heavy duty fibre cement board(High Pressure Steam Cured) Type A,Category 4 conforming to IS 14862:2000, fixed on Steel frame work of 610mmx610mm or 610mmx1220mm grid by counter sunk stainless screw @ 300mm C/C all complete as per the drawings. Tiles etc may be laid on the board substrate by sealing the joints properly with filler material or sealant to ensure no leakage through joints. All complete as per drawings, specification and as per direction of Engineer-in-Charge. Note - MS Section structure and roof tile like Shingles/Mangalorian Tiles etc cost will be paid seprately.

Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS : 8183, density 16kg/m3, 50mm thick, wrapped in 200G Virgin Polythene bags placed over existing false ceiling and held in position by criss-crossing GI wire.

Thermal Insulation of roofing with Expanded polystyrene fixed with suitable adhesive to the false ceiling as per the directions of the Engineer-in-charge :

Providing and laying thermal insulation of roofing with 40 mm thick impervious sprayed, closed cell free Rigid Polyurethane foam over deck insulation conforming to IS - 12432 Pt. III (density of foam being 40-45 kg/cum), over a coat of polyurethane primer applied @ 6-8 sqm per litre, laying 400 G polythene sheet over PUF spray and providing a wearing course of 40 mm thick cement screed 1: 2 : 4 (1 cement : 2 sand : 4 stone aggregate 20 mm nominal size) in chequered rough finish, in panels of 2.5 mx2.5 m and embedding with 24 G wire netting and sealing the joints with polymerized mastic, all complete as per direction of Engineer-in-Charge.

Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 24 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawl plug and washers and held in position by criss crossing GI wire etc. complete as per directions of Engineer-in- Charge.

Providing and fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Rockwool conforming to IS: 8183, density 48 kg/ m3, 50 mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5mm x 24 gauge wire mesh, for top most ceiling of building.

Providing and fixing thermal insulation with Resin bonded rock wool conforming to IS: 8183, density 48 kg/m3, 50 mm thick, wrapped in 200 G virgin Polythene bags placed over existing false ceiling and held in position by criss- crossing GI wire.

Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 48 kg/m3. 50 mm thick, wrapped in 200 G Virgin Polythene Bags fixed to wall with screw, rawl plug and washers and held and in position by criss cossing GI wire etc.complete as per directions of Engineer-in-Charge.

Supply and application of 48kg/m3 density & 50 mm thick with a tolerance of -2 + 6mm of Rockwool RB slabs unfaced (Binder<3.5%); conforming to IS: 8183/ASTM C 612 latest edition with amendments. Non- combustible when tested as per BS 476 Part 4 or A1 when tested as per EN: 13501. Two random samples from each supplied batch will be test for shot content at the site. The melting point of the wool shall be more than 1000°C and wool shall be bio-soluble in accordance with EU directive 127/2008 or similar. All Above mentioned standard are as per latest edition with amendments.

Supply & Application of Rockwool RB slab 48kg density, 50mm thick wrapped in 200G vergine polythene bags for partition, ceiling (Under Deck insulation) conforming to IS: 8183 with tolerance of -2 +6mm of rock wool RB slabs unfaced (Binder <3.5%) conforming to IS: 8183/ASTM C 612 latest edition with amendments. Non-combustible when tested as per BS 476 Part 4 or Al when tested per EN 13501. . Two random samples from each supplied batch will be test for shot content at the site. The melting point of the wool shall be more than 1000°C and wool shall be bio-soluble in accordance with EU directive 127/2008 or similar. All Above mentioned standard are as per latest edition with amendments.

Supply & Application of Rockwool RB 2 slab 64kg /m3, 50mm thick, with GI wire netting 24 SWG; fixing for NRC Value 1.00 for Acoustics, thermal & fire purpose conforming to and IS: 8133, IS: 8183 with tolerance of -2 + 6mm of RB slabs unfaced (Binder < 3.5%); conforming to IS: 8183/ASTM C 612 latest edition with amendments. Two random samples from each supplied batch will be tested for shot content at the site. The melting point of the wool shall be more than 1000°C and wool shall be bio-soluble in accordance with EU directive 127/2008 or similar. All Above mentioned standard are as per latest edition with amendments.

Supply & Application of Rockwool building roll (1.1mx10m) 48kg density, 50mm thick with FSK (foil scrim Kraft) aluminium foil facing for HVAC duct & building underdeck purpose conforming to IS: 8183, IS: 8183 and IS:8183 a tolerance of -2 +6 mm of Rockwool RB slabs unfaced (Binder < 3.5%) ; conforming to IS: 8183; /ASTM C 612 latest edition with amendments. Non-combustible when tested as per BS: 476 Part 4 or Al when tested as per EN: 13501. Two random samples from each supplied batch will be test for shot content at the site. The melting point of the wool shall be more than 1000°C and it shall be bio-soluble in accordance with EU directive 127/2008 or similar. All Above mentioned standard are as per latest edition with amendments.

Supply & Application of Rockwool Building Roll (1.1mX10m) 48kg density, 50mm thick with ALG (Alu & glass) mixture of Aluminium & glass facing for building underdeck application below metal sheet also conforming IS: 8183, IS: 8183 and IS: 8183 a tolerance of -2+6mm of rockwool RB slabs unfaced (Binder < 3.5%); conforming to IS: 8183/ASTM C 612 latest edition with amendments. Non-combustible when tested as per BS 476 Part 4 or Al when tested as per EN 13501. The maximum service temperature shall be 700°C. Shot content should be less than 2% for 500 microns & less than 10% for 250 microns when tested as per standard IS: 3144. Two random samples from each supplied batch will be test for shot content at the site. The melting point of the wool shall be more than 1000°C and wool shall be bio-soluble in accordance with EU directive 127/2008 or similar. All Above mentioned standard are as per latest edition with amendments.

Providing and fixing of minimum 12mm thick, 5 layered bubble Reflective thermal insulation made of 12 microns aluminum foil with minimum 97% Reflectivity on both outer sides, under both aluminum foil 4mm thick FR bubble insulation with Low Emissivity - 0.032 (ASTM1371), Fire Class A (ASTM E84) All five layers of insulation shall be stick with each other by registered manufacturer using hot process without using any kind of adhesive. Insulation shall be supplied in 1.10m wide roll width with 50mm wide factory-made cuts at both sides to joint another roll by using general stapler in case of new shed and adhesive in case of existing or self-supported roof.

Fixing of insulation on new work by laying horizontally on the purlins and perpendicular to the direction of purlins and fixing by using self- tapping screws at equal distance. Place and align the second roll of insulation parallel to the first roll and overlaps the adjacent rolls. After Insulation is fixed over the purlins the metal sheet is placed over insulation and drilled with self-tapping screws with purlins etc. complete, including all material and scaffolding.

Installation of insulation in Old Sheds where the sheets have been already fixed over the purlins so insulation shall be fixed under the purlins covering the roof bottom. Insulation roll to be unfolded at the bottom of the purlin horizontally and parallel to the roof and fixed by using the self- tapping screw with a washer at equal distance etc. Complete, including all material and scaffolding.

Insulation of Self-Supported Roof shall be applied under the roofing by using stud welding to the self- supported roof at a distance not be more than 300 mm in both directions. At each stud insulation roll shall be pushed against the studs so that it gets punctured and then non-returning washer has to be applied at the stud etc. complete, including all material and scaffolding.

Providing and fixing 50 mm thick extruded polystyrene rigid insulation board (XPS) of required size over- deck on ceiling surface, complying with ASTM C 578 - type VI, having thermal conductivity of 0.0289 W/mK as per ASTM C 518, compressive strength of > 350 kPa listed as per ASTM C 1621, density of 34-36 kg/m³ as per ASTM D 1622, water absorption < 1% by volume as per ASTM C 272, oxygen index of minimum 24 as per ASTM D 2863 and Fire retardant property as per DIN 4102, with preferred stone or pre-cast tiles shall be laid over the XPS board with suitable grouting including providing pre-fabricated EPDM drain outlets (Cement Screed casting shall be done at the junction of roof and parapet walls), all as per the directions of Engineer-in-charge.

Providing and fixing 50 mm thick extruded polystyrene rigid insulation board of required size underdeck on ceiling surface, complying with ISO 4898:2008 & ASTM C 578-08b - type VI, having thermal conductivity of 0.0289 W/m K as per ASTM C 578 Fire retardant property as per DIN 4102, Part 1 of class B2 and as per ASTM E84 class A, fixed with suitable water based adhesive and fastener, complete in all respect as per the directions of Engineer-in-Charge.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:

10mm thick plaster of Paris (gypsum anhydrous) sheet 10mm thick pop board

Flat surfaces

Curved surfaces

Sunk or raised mouldings

Extra for providing in the plaster of Paris (Gypsum anhydrous) ceiling above 5 metre height from floor level.

12.5 mm thick tapered edge gypsum board

Plain board conforming to IS: 2095- Part I : 2011 (Board with BIS certification marks).

Fire resistant Glass Reinforced Gypsum (GRG) board conforming to IS: 2095- (Part 3) : 1996 (Board with BIS certification marks)

Gypsum moisture resistant board.

Fully Perforated Gypsum Plaster Board having approx. 15 % perforated area with perforation size and pattern as approved by the Engineer-in-charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60.

8 mm thick Calcium Silicate Board made with Calcareous and Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of mainT" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre- painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending .

GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.

12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a ompletely sealed unit.

12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.

Glass fiber Acoustical Suspended Ceiling System with 16 mm thick tegular edge or micro look edge tiles of size 595x595mm.The tiles should have Humidity Resistance (RH) of 99%, NRC 0.5, Light Reflectance ≥83%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Colour White, Fire Performance UK Class 0 / Class 1 (BS 476 pt - 6 and7) in module size of 600 x 600 x 16mm with Bio Block coating on the face of the tile, suitable for Green Building application, with Recycled content of 38 - 41%. The Tile and Grid system used together should carry a 15 year warranty.

8mm thick non-asbestos multipurpose termite, fire & moisture resistance cement bonded particle board as per IS: 14276, white primedcolour tiles of size 595X595 mm.

6mm thick non-asbestos multipurpose termite, fire & moisture resistance cement bonded particle board as per IS: 14276, white primed colour tiles of size 595X595 mm.

Providing and fixing GI Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing ‘C’ wall angle of size 20x30x20mm made of 0.5mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300mm center to centre, suspending the main C carrier and in direction perpendicular to it at 600mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive) Fixing with clip in/swing down tiles into spring 'T' with

GI Metal Ceiling Clip in /swing down plain Beveled edge global white color tiles of size 600x600 and 0.5mm thick with 25mm height, made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

GI Metal Ceiling Clip in /swing down plain Beveled edge global white color tiles of size 600x600 and 0.5mm thick with 25mm height, made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.

Providing & Fixing of Unperforated Antibacterial Metal Tile Ceiling System comprising of Tile of 600mm wide and 600mm long manufactured out of 0.7mm thick aluminium alloy 3105 with beveled edge of 4.15mm width and height of 32mm. The Tile will be manufactured on advanced equipment that includes several levelling stages in the manufacturing process by approved certified manufacturers. The Tile shall be clipped into clip in rail of 0.5mm thick G.I. in form of a grid system using a cross connector. The clip in rail shall be supported from slab by means of rigid Suspension of 4mm G.I.Road, Hold on Clamp with Clip. (Rate include all materials and labour).

Providing and fixing board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately):

12mm thick insulating board

Natural colour insulating board

White face insulating board

Flame retardant face insulating board

Flat pressed 3 layer medium density particle board or graded particle board (Grade I) IS: 3087 12 mm thick marked in ceiling with necessary nails etc. complete

6 mm thick plain Multipurpose Cement board ( High Pressure steam cured ) as per IS : 14862, with suitable screws for fibre cement board in ceiling etc. complete

6mm thick High Pressure Steam Cured non asbestos, reinforced with cellulose fibres,Moistur& fire Resistance heavy duty fibre cement board, Type A,Category 4 conforming to IS 14862:2000.(for wet areas)

4 mm thick High Pressure Steam Cured non asbestos, pre-painted, self- embossed, designer cement boardType B, Category 3 conforming to IS 14862:2000 . of approved texture,design patterns

Extra for Circular cutting and wastages in ceiling with: board only (frame work) Natural colour insulating 12 mm thick board paid separately.

Extra for providing and fixing ceiling to curved surfaces in narrow widths

Providing and fixing false ceiling with 12 mm thick plain/ semi perforated or with design ceiling tiles of BWP type phenol formaldehyde synthetic resin bonded pressed particle board conforming to IS:3087, finished with a coat of aluminium primer on both sides and edges including two coats of synthetic enamel paint of approved quality on exposed face, fixed to a grid made out of anodised aluminium (with 15 micron anodic coating) The frame work shall be suspended from ceiling by level adjusting hangers of 6 mm dia M.S rod fixed to roof slab by means of ceiling cleats and dash fastener. The suspenders shall be placed 600 x 1200 mm centre to centre including fixing to the frame with C.P brass screws and applying a priming coat of zinc chromate yellow primer (aluminium frame work shall be paid separately).

Providing and Fixing colour coated profile sheet of minimum 1015 mm effective cover width and nominal 28.5 mm deep ribs with subtle square fluting in the five pan at nominal 203 mm centre-to-centre. The end rib shall be designed for anti-capillary action, to avoid any seepage of water through the lateral overlap. The sheet shall have brand marking of the manufacturer giving product details on the back of the sheet at every 1 meter c/c for confirming genuinity of the material. The sheet shall be fixed using self- drilling /self-tapping screws of size (5.5x 55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape

Extra for providing 3 mm thick translucent white acrylic plastic sheets of approved quality in false ceiling instead of 12 mm thick plain or design particle board ceiling tiles.

Providing and fixing expanded polystyrene (thermacol) false ceiling (frame work to be paid separately) :

With Type N - Normal 50 mm thick

With Type SE - Self Extinguishing type 50 mm thick

costing upto 70/- per metre,

Rs 70- 150 per meter

Upto 200 per meter

Providing and fixing perforated Aluminium panel ceiling of white/ natural satin colour supplied by approved manufacturers consisting of panel of standard size with bevel edge, panel length up to 6 m, coil Coated on a Continuous Paint Line suitable for Interior application, double baked and roll formed from enamelled corrosion resistance aluminium alloy AA 5050 (Al. Mg) for higher strength and good roll forming characteristics. Panel carrier shall be suspended by means of G.I. threaded rod having 6 mm diameter at a distance of 1.5 mtr. Actual distance of threaded rod/carrier might vary and to be calculated based on the actual drawing and site condition. The Measurements shall be wall to wall without any deductions for lights, diffusers, columns etc.

With panels of size 300mm wide X30mm deep X 0.7mm thick and panel carrier of size 40.5mm wide X 62mm deep X 0.9mm thick

With panels of size 150mm wide X 15.5 mm deep X 0.5mm thick and panel carrier of size 32mm wide X 39mm deep X 0.95mm thick

With panels of size 84mm wideX16mm deep X 0.5mm thick and panel carrier of size 62mm wide X 29mm deep X 0.95mm thick

Providing and fixing un-perforated Aluminium Panel ceiling Supplied by approved manufacturers of standard white/ natural satin shade consisting of panel 30 mm/80mm/130mm/180mm wide X 15 mm deep X 0.5mm /0.6mm thick respectively, with square edges having panel length up to 6 mtr, Coil Coated on a Continuous Paint Line, Double baked and roll formed from enamelled corrosion resistance Aluminium alloy AA 5050 (Al.Mg) for higher strength and good roll forming characteristics. The Carrier shall be suspended by means of G.I. suspension rod 4mm diameter, and a Galvanised suspension spring clip at a distance of 1.7mtrs centre to centre. Actual distance of threaded rod/carrier might vary and to be calculated based on the actual drawing and site condition. The Measurements shall be wall to wall without any deductions for lights, diffusers, columns etc.

Providing and fixing U Baffle Aluminium panel ceiling of different colors and finish supplied by approved manufacturers, consisting of panel size 50 mm width X 100 mm deep using 0.6 mm thick, panel length upto 4 mtr, Coil Coated on a Continuous Paint Line, Double baked and roll formed from enamelled corrosion resistance Aluminium alloy AA 3005 (Al. Mg) for higher strength and good roll forming characteristics. Actual distance of threaded rod/carrier might vary and to be calculated based on the actual drawing and site condition. The measurements shall be wall to wall without any deductions for lights, diffuses, columns etc. As an option, ceiling area above U Baffle can be painted by the contractor in black colour or any other colour as per the architect for better aesthetics before fixing this system.

Standard White / Natural Satin Shade

Wooden Finish

Supply & Fixing of perforated G.I false ceiling tile or plank using torsion spring fixing system supplied by approved manufacturer comprising of tile of 600 mm wide and 600 mm long manufactured out of 0.5 mm thick or plank of 600mm wide and 1200 mm long manufactured out of 0.6mm thick galvanised steel perforated with 2 mm dia. at a distance of 5mm centre to centre. Non-woven felt made of glass- reinforced fibre glued over the perforation at the back side of panels to provide noise reduction co efficient up to 0.7 NRc. “Tee” sections, 3.6m long, with factory punched flanges to receive torsion spring assembly. Main Tee on centre spacing to match panel length. Cross runners 24 mm deep, inverted “Tee” sections designed to interlock in to web of main tee section on designated spacing. Cross tee length to match panel length. Cross tees are spaced at a spacing of 600 mm on centre maximum. The measurements shall be wall to wall without any deductions for lights, diffusers, columns etc.

Tile of 600 mm wide ,600 mm long and 0.5 mm thick

Plank of 600mm wide ,1200 mm long and 0.6mm thick

Providing and fixing of composite perforated Gypsum board with Glass wool Fiber panel of Size 595x595x25 mm with 10mm square Perforation tiles false ceiling in true horizontal level suspended on interlocking metal grid of hot dipped galvanized steel section (Galvanized @ 120 gms/sqm both sides inclusive) consisting of main “ “T” runners to be suspended from ceiling using GI slotted plates of size 27x37x25x1.6 mm fixed to ceiling with 12.50 mm dia and 40 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85x30x0.80 mm spaced @ 1200mm centre to centre along with main T, bottom exposed width of 24mm of all T-sections shall be pre- painted with polyester paint all complete at all heights as per specifications and drawings and as directed by Engineer-in-Charge.

Providing and fixing of Composite perforated MDF board with Glass wool Fiber panel of Size 595x595x18 mm 10mm Square Perforation tiles (Square /Tegular Edge) false ceiling in true horizontal level suspended on interlocking metal grid of hot dipped galvanized steel section (Galvanized @ 120 gms/sqm both sides inclusive) consisting of main “T” runners to be suspended from ceiling using GI slotted plates of size 27x37x25x1.6 mm fixed to ceiling with 12.50 mm dia and 40 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85x30x0.80 mm spaced @ 1200mm centre to centre along with main T, bottom exposed width of 24mm of all T-sections shall be pre- painted with polyester paint all complete at all heights as per specifications and drawings and as directed by Engineer-in-Charge.

Providing and fixing of Perforated Gypsum board with Acoustical Glass Fiber Tissue faced panel of Size 595x595x12.5mm, Square 10mm Perforation tiles (Square Edge) false ceiling panels in true horizontal level suspended on interlocking metal grid of hot dipped galvanized steel section (Galvanized @ 120 gms/sqm both sides inclusive) consisting of main “T” runners to be suspended from ceiling using GI slotted plates of size 27x37x25x1.6 mm fixed to ceiling with 12.50 mm dia and 40 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85x30x0.80 mm spaced @ 1200mm centre to centre along with main T, bottom exposed width of 24mm of all T-sections shall be pre- painted with polyester paint all complete at all heights as per specifications and drawings and as directed by Engineer-in-Charge.

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance≥ 85%, Thermal Conductivity k = 0.052 -0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking TGrid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling usinggalvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be prepainted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-incharge. With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6)

Providing and fixing false ceiling at all heights with 15 mm thick integral densified micro look edged non- cementitious light weight calcium silicate false ceiling tile reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.80 grams per sqm) i.e. 50 mm long, 12 mm outer diameter M-6 dash fasteners with the help of Z cleat of 27x37x27x2 mm, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm centre to centre and 40mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

Providing and fixing false ceiling at all heights with 15 mm thick integral densified mirolook edge with BIO SAFE coating as per ISO 7251:2005, ISO 20743:2007 and ISO 21527-1:2008, making the tiles resistant to bacterial growth in case of any external bacterial contact made onto the surface of tiles, non-cementitious light weight calcium silicate false ceiling tile reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm with the help of Z cleat of 27x37x27x2 mm, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm centre to centre and 40mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

Providing and fixing in position wall panelling at all heights with 15 mm thick fully perforated square/butt edge light weight calcium silicate panels/ tiles., non-cementitious, reinforced with fibre and natural filler, having NRC (Noise Reduction Coefficient) of 0.10-0.20 for plain and designer 0.15-0.40 for pinhole texture and NRC 0.45-0.65 for fully perforated tiles as per IS 8225:1987, sound attenuation STA-32db. of 0.75 (minimum) as per IS 8225:1987, Light Reflectance of 85% (minimum), non-combustible as per BS:476 (part-4), 50-52% recycled content including fly ash, The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fibre joint tape roll 50mm wide (90 metre) roll and two coats of primer suitable for panelling as per manufacturer's specification as per direction of engineer-in-charge all complete. With 15 mm thick fully perforated square/butt edge light weight calcium silicate panels/ tiles.

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in- Charge.

With semi perforated 12mm thick micro tegular edged GRG false ceiling tiles.

With fully perforated 10mm thick square edged GRG false ceiling tiles for sound proof and acoustic.

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped 387alvanized steel sections (387alvanized387 @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cros‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer- in-Charge.Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/ opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity

Providing and fixing upvc plank, Plank size (340 X 2700 ) mm as per approved shade, the panel shall be laser catted end of plank fixing j-trim fixed and corner edge of ceiling fixed u pvc clip same colour and providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 125 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts,other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular,j trim end clip includes in this item any other item not be paid sepratly complete in all respect as per the directions of Engineer-in-Charge. .

Providing & Fixing PVC ceiling system profile panel with click system interlock panel size 4000mmx340mmx1mm resistance to weather perfect finish in wood grain & solid colour maintenance free Resistance to weather truly anti bacterial. with edge profile J-trim on periphery & center profile T-trim in panel joint Complete System to be fixed on G.I. framework of ceiling section at 450 mm distance with enter section suspended by roof by G.I. angle hanger in proper line & level etc complete . PRODUCT SPECIFICATIONS: Meets or exceeds the standard specification of (ASTM D-4477) and its referenced documents. observed. (Tested at 50 LBS) Tensile strength, MPa: >37.0 Tensile modulus, MPa: >2000 Surface distortion: None at 120F Squareness: <1/8” of square Length: Within ¼” of specification Lock control: Complies Color Change: <2 grayscales (16 hrs under 1200W/m2 UV radiation at 50 degrees)

Design built, supply and erection of Tensile (fabric) structure system including designing and fabrication in M.S. steel tubular structure as per Indian standard section as per approved design and shape including base plate, dash fastener, clits etc. Cutting, patterning, plotting and wielding of fabric with the help of tensile structure software. Fabric should be wielded by high frequency PVC wielding in proper line with PVC cader to be fixed on end of the fabric and to be stretched & fixed on M.S. design structure with the help of. M.S. Flat bar with self-taping screw. M.S. structure to be painted with one coat of epoxy primer with MRF PU paint of approved colour in desired shape. With 1050 GSM tensile fabric

With precontraint tensile membrane 1050 GSM (20 years Warranty)

With precontraint tensile membrane 1050 GSM (15 Years warranty)

Neat cement punning

Rough cast plaster upto 10m height above ground level with a mixture of sand and gravel or crushed stone from 6mm to 10mm nominal size dashed over and including the fresh plaster in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 sand) and top layer 10mm cement plaster 1:3 (1 cement: 3 sand) mixed with 10% finely grounded hydrated lime by volume of cement. Finished with ordinary cement.

Pebble dash plaster upto 10m height above ground level with a mixture of washed pebble or crushed stone 6mm to 12.5mm nominal size dashed over and including fresh plaster in two layers under layer 12mm cement plaster 1:4 (1 cement: 4 sand) and top layer 10mm cement plaster with cement mortar 1:3 (1 cement: 3 sand) mixed with 10% finely grounded hydrated lime by volume of cement.

Providing sand faced plaster upto 10meter hight above ground level concrete or brick masonry surfaces in two coats, base coat of 13 mm thick in cement mortar 1:4 (1 cement: 4 sand), clearing the surface by combing it and finishing coat of 8 mm. thick in cement mortar 1:3 (1 cement: 3 sand) and taking out surface grains by mechanical arrangement or applying second coat by mechanical means including cost of all material, labour, and T and P including all lead, lift and scaffolding etc. complete.

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Extra for plastering

Exterior walls of height more than 10 m from ground for every additional height of 3 m or part thereof

Interior walls of height more than 6 m from floor level for every additional height of 3 m or part thereof

Extra for plastering on circular work not exceeding 6 m in radius:

In one coat

In two coats

Extra for plastering done on moulding cornices or architraves including neat finish to line and level:

In one coat

In two coats

Extra for plastering Spherical, Groined ceiling, Flewing soffits.

Spherical ceiling

Groined ceiling

Flewing soffits

Washed stone grit plaster on exterior walls of height upto 10 M. above ground level in two layers, under layer 12mm cement plaster 1:4 (1 cement : 4 sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement : 1/2 sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings,complete as per specification and direction of Engineer- in- charge (Payment for providing grooves shall be made separately).

Forming groove of uniform size 20 or 15 mm wide and 15 mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge :

Extra for washed grit plaster on exterior/interior walls of height more than 10m from ground/floor level for every additional height of 3 m or part thereof.

Extra for washed stone grit plaster on circular work not exceeding 6m in radius (in two coats).

Forming groove of uniform size from 12x12mm and upto 25x15mm in the top layer of washed stone grit plastered surface as per approved pattern, including providing and fixing aluminum channels of appropriate size and thickness (not less than 2 mm), nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.

Extra for using white cement in place of ordinary cement in the top layer of the item of washed stone grit plaster.

Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part -1 and II) 1976, applied on hacked/ uneven background such as bare brick/ block/ RCC work on walls and ceiling at all floors and locations,excluding in wall which may come in contact with dampness finished in smooth line and level etc. complete.

Extra for addition of synthetic Polyester triangular fibre of length 6mm, effective diameter 10-40 microns and specific gravity of 1.34 to 1.40 in cement plaster/mortar by using 125gms. Of synthetic Polyester triangular fibre for 50 Kgs. cement used in cement mortar as per directions of Engineer-in-Charge.

Providing and fixing mesh in vertical and horizontal junction of RCC and brick/AAC work including scaffolding and all lead and lift etc. complete

Providing and fixing fibre mesh of 145 GSM weight in required width with cement mortar before plastering upto 10m height.

12 mm thick plain cement mortar bands in cement mortar 1:4 (1 cement : 4 sand) :

Flush Band

Sunk Band

Raised Band

Moulded Band

18 mm thick plain cement mortar band in cement mortar 1:4 (1 cement : 4 sand):

18 mm thick moulded cement mortar band in two coats under layer 12mm thick with cement mortar 1:5 (1 cement : 5 sand) top layer 6mm thick with cement mortar 1:4(1 cement : 4 sand).

Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 sand) :

Flush / Ruled/ Struck or weathered pointing.

Raised and cut pointing

Sunk pointing

Pointing on stone work with cement mortar 1:3 (1 cement: 3 sand).

Flush/ Ruled pointing

Raised and cut pointing

Raised and cut pointing on stone work in white cement mortar 1:3 (1 white cement : 3 marble dust)

Pointing on stone slab ceiling with cement mortar 1:2 (1 cement : 2 sand): Flush/ Ruled pointing

Extra for pointing on walls on the outside/inside at height more than 10 metre from ground/floor level for every additional height of 3 m or part there of.

Providing and fixing broken glass in cement mortar 1.3 including cost of mortar, over compound walls.

Providing and fixing writing board green writing with chalk (regular modified polyster coated steel surface). of sizes.

size 1200mmx1800mm

size 1200mmx2400mm

size 1200mmx3000mm

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

Providing and applying plaster of paris punning of 10 mm average thickness over plastered surface to prepare the surface even and smooth complete.

Extra for lining out plaster to imitate stone or concrete blocks walling.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand over the plastered wall surface to prepare the surface even and smooth i/c all cost of material, labour and scaffold etc in all position complete. Note : Putty shall be applied only on the internal walls, for application on the exterior walls prior permission of APD/Chief Engineer will be required.

Providing and applying special putty in two coats based materials varnish, Belgium chalk, turpentine oil, white paint, safeda including sand papering for making the surface smooth for applying any or vinyl paints including all cost of material and labouretc complete.

White washing with lime to give an even shade: New work (three or more coats)

Colour washing such as green, blue or buff to give an even shade: New work (two or more coats) with a base coat of white washing with lime.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound) content less than 50 grams/ltr of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coat on new work.

Wall painting by any mechanical or manual means with plastic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work

Distempering by any mechanical or manual means with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

One coat.

Two coats.

Wall painting by any mechanical or manual means with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

One coat.

Two coats.

Wall painting by any mechanical or manual means with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ litre. of approved brand and manufacture, including applying additional coats wherever required to achieve even shade.

Finishing walls by any mechanical or manual means with water proofing cement paint of required shade: New work (Two or more coats applied @ 3.84 kg/10 sqm).

Finishing walls by only mechanical or manual means with textured exterior paint of required shade: New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm.

Finishing walls by any mechanical or manual means with Acrylic Smooth exterior paint (Economy Exterior) of required shade including all scaffolding. New work (Two or more coat applied @1.67ltr/10sqm over and including one coat undiluted exterior waterproofing coating @ 2.39 litre/10 sqm with crack bridging ability of upto 0.5mm on horizontal surfaces with an elongation of 150% and water proofing of upto 3 bars on vertical surface

Finishing walls by any mechanical or manual means with Premium Acrylic Smooth exterior paint (Premium exterior) of required shade including all scaffolding. New work (Two or more coat applied @1.67ltr/10sqm over and including one coat undiluted exterior waterproofing coating @ 2.39 litre/10 sqm with crack bridging ability of upto 0.5mm on horizontal surfaces with an elongation of 150% and water proofing of upto 3 bars on vertical surface)

Finishing walls by any mechanical or manual means with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture.

Two or more coats applied on walls @ 1.25 ltr/10 sqm. Over and including one coat of Special primer applied @ 0.75 ltr / 10 sqm.

Painting with silicon and acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces:

One coat

Two coats

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.

On steel work

On concrete work

Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution.

Applying a coat of mordant solution on G.S. sheet :

With a solution of 38 gms of copper acetate in a litre of soft water

With a solution made of 13 gms of hydrochloric acid in a solution of 13 gms each of copper chloride, copper nitrate and ammonium chloride dissolved in a litre of soft water.

Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with black anticorrosive bitumastic paint approved brand and manufacture over and including a priming of ready mixed zinc chromate yellow primer on new work :

75 mm diameter pipes

100 mm diameter pipes

150 mm diameter pipes

Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work.

75 mm diameter pipes

100 mm diameter pipes

150 mm diameter pipes

Painting with oil type wood preservative of approved brand and manufacture: New work (two or more coats)

Providing and applying two coats of fire retardant paint on cleaned wood/ply surface @ 3.5 sqm per litre per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant.

Coal tarring two coats on new work using 0.16 and 0.12 litre coal tar per sqm in the first coat and second coat respectively.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.

One coat.

Two coats.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content.

With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre.

With ready mixed red oxide zinc chromatic on steel/ iron works having VOC content less than 250 grams/litre.

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre.

Painting with aluminium paint of approved brand and manufacture to give an even shade. Two or more coats on new work.

Painting with acid proof paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work.

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade: Two or more coats on new work.

Floor painting with floor enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work

Varnishing with varnish of approved brand and manufacture:

Two or more coats of glue sizing with copal varnish over an under coat of flatting varnish.

Two or more coats glue sizing with spar varnish or an under coat of flatting varnish.

French spirit polishing: Two or more coats on new works including a coat of wood filler.

Polishing on wood work with ready mixed wax polish of approved brand and manufacture: New work.

Lacqer polishing on door windows by preparing the surface applying putty base course. Prepare the surface smooth by sand papering and then applying lacqer polish with air compressor. Two or more coats on new works including a coat of wood filler.

Mealamine polishing on door windows by preparing the surface applying putty base course. Prepare the surface smooth by sand papering and then applying mealamine polish with air compressor. Two or more coats on new works including a coat of wood filler.

Floor polishing on masonry or concrete floors with wax polish of approved brand and manufacture.

Lettering with black Japan paint of approved brand and manufacture.

Providing and applying flakes textured homogeneous wall finishing system consisting of a two component system of dry flakes (9.5kgs per/pack) made of a special grade of heat treated China clay with rigid homopolymer coated with fade resistant pigments and a 100% acrylic polymer Bonding agent (5kgs/pack) applied thickness of the coating being between 0.8-1.2mm, to be applied in single coat, on a cured, smooth level plaster surface without keying, as per the shades/ combinations approved, as per manufacturers directions for usage, to be applied by approved applicator of manufacturer, as per direction/ supervision of the engineers-in-charge inclusive of one coat of primer on the base at all heights etc all complete.

Providing and applying Granules homogeneous wall finishing system consisting of a two component system of dry granules (25 kgs/pack) made of 92% silica particles coated with fade resistant pigments and a 100% acrylic Polymer Bonding agent (5 kgs/pack) with the applied thickness of coating as required to be applied in single coat, on a cured. Smooth level plaster surface without keying as per the shades/combinations approved. As per the manufacturers directions for usage, to be applied by approved applicator of manufacturer, as per the directions/supervision of engineers in charge, all complete inclusive of primer on the base.

0.8-1.2mm thickness

2.0-2.5mm thickness

Providing and Applying Roto Wall finishing system being a dispersion of inorganic fillers, calcite, pure silica, quartz and broad spectrum fungicides stabilized by an acrylic co-polymer, to be applied by means of customized trowels (one for incorporating material on base and spreading and other for finishing) in single coat with a coating thickness of 2.0-2-2.5mm on a cured smooth level plaster without keying, by the approved applicator of manufacturer, of the approved shade as per directions for usage all inclusive including primer coat on the base.

Providing and plastering over AAC masonary wall with polymer modified cement based readymix factory controlled mortar with self curing, eco- friendly, wet premix in a mechanical mixer in thickness as specified below, and covering area of 2.04 kg per sqm/mm thickness. The Bulk density of ready mix plaster may vary from 1300 to 1600 Kg/cum, Water powder ratio (as per manufacture’s direction) may vary from 18-22 % by weight or as specified by the manufacturer and compressive strength may vary from 8-9 Mpa.

6 mm thick plaster for internal walls

8 mm thick plaster for external walls exposed to weather.

Providing and fixing including Designing and UV printing on aluminium composite material (ACM) sheet in different sizes with 720DPI (Dot per inch)

ACP sheet 2mm thick

ACP sheet 3mm thick

ACP sheet 4mm thick

Providing and fixing including designing and UV printing on pvc foam sheet of different size with 720 DPI (Dot per inch)

PVC foam sheet 3.0 mm thick

PVC foam sheet 5.0 mm thick

PVC foam sheet 8.0 mm thick

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Providing and fixing 50 mm thick extruded polystyrene rigid insulation board (XPS) of required size over outer wall surface, complying with ASTM C 578 - type VI, having thermal conductivity of 0.0289 W/mK as per ASTM and Fire retardant property as per DIN 4102, Part 1. XPS insulation of thickness 50mm shall be placed over brushed, algae free and levelled external wall by connecting the ship-laps joints and fixed by the washer and Self-Tapping Screw of suitable length at each corner and at distance 75mm from the edge and bitumen shall be applied over the joints and G.I. Expanded Mesh (Barfi Jali) shall be fixed over XPS board by a Self- Tapping Screw of suitable length at the centre of the board and 15mm PCC shall be applied over the board (paint of suitable choice can be used), all as per the directions of Engineer-in-Charge.

Providing and fixing 50 mm thick extruded polystyrene rigid insulation board of required size between cavity wall, complying with ISO 4898:2008 & ASTM C 578-08b - type VI, having thermal conductivity of 0.0289 W/m K as per ASTM C 578 (measured as per IS 3346), compressive strength of > 350 kPa listed as per ASTM D 1621, density of 34-36 kg/cum as per ASTM D 1622, water absorption < 1% by volume as per ASTM D 2842, oxygen index of 24.1 to 28.1 listed as per ASTM D 2863, cell size 0.4 mm of dia (max) as per ASTM D 3576. Fire retardant property as per DIN 4102, Part 1 of class B2 and as per ASTM E84 class A, fixed with suitable water based adhesive and fastener, complete in all respect as per the directions of Engineer-in-Charge.

Painting with oil type wood preservative of approved brand and manufacture: Old work (one or more coats)

Scrapping/sand papering of existing surface with the help of mechanized sanding machine (having mechanical vaccum machine with bag for dust collection to make surface even and smooth) as per direction of Engineer-in- Charge.

Providing and applying 1 coat of Triple booster primer-resist dampness, efflorescence, alkali & at the same time improve top coat coverage by 15-20% @1.0 lt/ 10 sqm, which confirms certfication of IS 109/1968. It can be applied by Brush/ Spray Machine and the work shall be carried out as per secification& the direction of the Engineer-in-Charge.

Finishing walls with water based anti- germ paint of with VOC < 50 g/l, that kills disease causing germs, teflon based washability and Anti fungal properties in two or more coats @ 1.08 ltr / 10 sqm over priming coat of interior primer applied @ 1.08 ltr / 10 sqm of required shade including removing of all dust complete as per direction of Engineer- in-Charge and submission of challans of materials on enquiry.

Providing and applying in two coats of 250 micron thick each layer of epoxy coating on prepared surface (cost includes preparing the plastered surface smooth ready to receive epoxy coating) for operation theater walls in desired colour as per direction of Engineer-in-Charge .

Door chowkhats

Window chowkhats

Clerestory window chowkhats

Float glass panes of thickness 4 mm

Float glass panes of thickness 5.5 mm

Float glass panes of thickness 4 mm

Float glass panes of thickness 5.5 mm

Float glass panes of thickness 4 mm

Float glass panes of thickness 5.5 mm

2nd class teak wood fillets

Haldu/Bija/Kail wood fillets.

Refixing old glass panes with putty and nails.

Fixing old glass panes with wooden fillets (excluding cost of fillets).

Providing and fixing 16 mm M.S. Fan clamps of standard shape and size in existing R.C.C. slab including cutting chase, anchoring clamp to reinforcement bar, including cleaning, refilling, making good the chase with matching concrete, plastering and painting the exposed portion of the clamps complete.

Replacing sand stone slabs in roofing laid in cement mortar 1:4 (1 cement : 4 sand) including necessary repairs and cement pointing with same mortar complete including disposal of rubbish to dumping ground within 50 metres of lead :

Red/ white sand stone slabs 30 to 50 mm thick.

Renewing wooden battens in roofs, including making good the holes in wall and painting with oil type wood preservative of approved brand and manufacture complete including removal of rubbish to the dumping ground within 50 metres lead :

Sal wood battens.

Renewing wooden beams in roofs including making good the holes in walls and painting with oil type wood preservative of approved brand and manufacture complete including removal of rubbish to the dumping ground within 50 metres lead :

Not exceeding 4.00 metres in length.

Sal wood beams

Haldu/Bija/Kail wood fillets.

Above 4.00 metres and upto 5.00 metres length.

Sal wood beams

Haldu/Bija/Kail wood fillets.

Raking out joints in lime or cement mortar and preparing the surface for re-pointing or replastering including disposal of rubbish to the dumping ground within 50 metres lead.

Taking out wind ties from roof including cutting out rusted bolts, nuts etc. and removing materials to any distance within compound and stacking.

Fixing of old wind tie with new fittings including painting two or more coats with anticorrosive bitumastic paint of approved brand and manufacturer over and including priming coat of ready mixed zinc chromate yellow primer of approved brand.

Renewing bottom rail and/or top runner of collapsible gate including making good all damages and applying priming coat of zinc chromate yellow primer of approved brand and manufacturer.

Renewing Wrought iron or M.S. Wheel or roller of steel door or gate and fitting and fixing the same with necessary clamps, nuts and bolts/welding and erection etc. complete.

Wheel 50 mm dia. and below.

Wheel above 50 mm dia.

Providing and fixing 25 mm thick shutters for cupboard etc. :

Panelled or panelled and glazed shutters :

Superior class teak wood including nickel plated bright finished M.S. piano hinges with necessary screws.

Ist class teak wood including nickel plated bright finished M.S. piano hinges with necessary screws.

Glazed shutters :

Superior class teak wood including nickel plated bright finished M.S. piano hinges with necessary screws.

Ist class teak wood including nickel plated bright finished M.S. piano hinges with necessary screws.

Providing and fixing plain jaffri door and window shutters including bright or/and black enamelled M.S. butt hinges with necessary screws 35x10mm laths placed 35mm apart (frames to be paid separately) including fixing 50x12mm beading complete with:

Second class teak wood.

Hard wood, finger jointed

Providing and fixing curtain rods of 1.25mm thick brass plates with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete.

20 mm diameter.

25 mm diameter.

Providing and fixing M.S. round or square bars with M.S. flats at required spacing in wooden frames of windows and clerestory windows.

Providing joists (karries) including hoisting fixing in position and applying wood preservative on unexposed surface etc. complete with:

Sal wood.

Haldu/Bija/Kail wood.

White washing with lime old work to give an even shade :

two or more coats

one or more coats

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Distempering with dry distemper of approved brand and manufacture (one or more coats) and of required shade on old work to give an even shade.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: Old work (one or more coats).

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Old work (one or more coats).

Painting (one or more coats) on rain water, soil, waste and vent pipes and fittings with black anticorrosive bitumastic paint of approved brand and manufacture on old work :

75 mm diameter pipes

100 mm diameter pipes

150 mm diameter pipes

Painting (one or more coats) on rain water, soil, waste and vent pipes and fittings with aluminium paint of approved brand and manufacture on old work :

75 mm diameter pipes

100 mm diameter pipes

150 mm diameter pipes

Painting (one or more coats) on rain water, soil, waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour on old work :

75 mm diameter pipes

100 mm diameter pipes

150 mm diameter pipes

Painting with oil type wood preservative of approved brand and manufacture: Old work (one or more coats)

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: One or more coats on old work.

Painting with aluminium paint of approved brand and manufacture to give an even shade: One or more coats on old work.

Painting with acid proof paint of approved brand and manufacture of required colour to give an even shade: One or more coats on old work.

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade: One or more coats on old work.

French spirit polishing: One or more coats on old work.

Mealamine polishing on wood work by preparing the surface applying putty base course. Prepare the surface smooth by sand papering and then applying Mealamine polish with air compressor. One or more coats on old work.

Lacquer polishing on wood work by preparing the surface applying putty base course. prepare the surface smooth by sand papering and then applying Lacquer polish with air compressor

One or more coats on old work.

Polishing on wood work with readymade wax polish of approved brand and manufacture :

Old work

Re-lettering with black Japan paint of approved brand and manufacture.

Painting (one or more coats) with black Japan paint of approved brand and manufacture to give an even shade.

Providing and fixing C.P. brass chain and rubber plug complete for sink or wash basin :

32 mm dia

40 mm dia

Distempering with 1st quality acrylic washable distemper (ready mixed) of approved manufacturer and of required shade and colour complete. As per manufacturer's specification. One or more coats on old work.

Finishing walls with water proofing cement paint of required shade :

Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 liters/10 sqm complete including cost of Priming coat.

Old work (one or more coats @ 2.20 kg/10 sqm) complete.

Finishing walls with textured exterior paint of required shade :

Old work (Two or more coats on existing cement paint surface applied @ 3.28 ltr/10 sqm.

Old work (One or more coats) applied @ 1.82 ltr/10 sqm.

Finishing walls with Acrylic Smooth exterior paint of required shade :

Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface).

Old work (One or more coat applied @ 0.90 ltr/10 sqm).

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade

Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface.

Old work (one or more coats applied @ 0.83 ltr/10 sqm).

Finishing walls with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :

One or more coats applied on walls @ 0.85 ltr/10 sqm.

Painting wood work with Deluxe Multi Surface Paint of required shade. One or more coat applied @0.70 ltr/10 sqm

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. One or more coat applied @0.70 ltr/10 sqm.

Varnishing with varnish of approved brand and manufacture:

One or more coats with copal varnish.

One or more coats with spar varnish.

Melamine polishing on wood work (one or more coat). Old work

Varnishing with flatting varnish of approved brand and manufacture one or more coats on old work.

Floor painting with floor enamel paint of approved brand and manufacture of required colour to give an even shade. One or more coat on old work.

40 mm thick stone flooring over 20 mm (average)thick base of cement mortar 1:5 (1 cement : 5 sand) including pointing with cement mortar 1:2 (1 cement : 2 sand) with an admixture of pigment to match the shade of stone. Red sand stone / White sand stone) stone to be supplied by the department.

Rough chiseled dressed stone

Fine dressed stone

Coursed rubble masonry (second sort) with hard stone in Cement mortar 1:6 (1 cement : 6 sand) (Stone shall be supplied by the department)

Laying old cement concrete interlocking paver blocks of any design/shape laid in required line, level, curvature, colour and pattern over and including 50mm thick compacted bed of sand, filling the joints with sand etc. all complete as per the direction of Engineer-in-charge. (Old CC paver blocks shall be supplied by the department free of cost).

Laying at or near ground level old kerb stones of all types in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 sand) including making joints with or without grooves (thickness of joints, except at sharp curve, shall not be more than 5mm) including making drainage opening wherever required etc. complete as per direction of Engineer-in- charge. (Length of finished kerb edging shall be measured for payment). (Old kerb stones shall be supplied by the department free of cost).

Colour washing with lime to give an even shade:

(one or more coats)

(two or more coats)

Conducting adequate no's. of scanning to detect the steel reinforcement in existing RCC elements by using ground/ Wall penetrating radar system to avoid the cutting of Main bars during drilling for inserting bolts etc. complete.

Chipping, Removing, Carefully loose plaster and Concrete work by low impact Hammer, Breaker without damaging the structure as Instructed by Engineer-in-Charge.

Rebaring of TMT bars by drilling hole & embedding bars of different diameter using epoxy grouting compound including all tools and tackles complete.

8 mm dia bar 10 mm dia hole

10 mm dia bar 12 mm dia hole

12 mm dia bar 16 mm dia hole

16 mm dia bar 20 mm dia hole

20 mm dia bar 25 mm dia hole

25 mm dia bar 32 mm dia hole

32 mm dia bar 40 mm dia hole

Providing and fixing chromium plated brass butt hinges with necessary chromium plated brass screws etc. complete.

125x70x4 mm (ordinary type)

100x70x4 mm (ordinary type)

75x65x4 mm (heavy type)

75x40x2.5 mm (ordinary type)

50x40x2.5 mm (ordinary type)

Providing and fixing 85x42 mm chromium plated brass pull bolt lock with necessary chromium plated brass screws, nuts, bolts and washers etc. complete.

Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-In-Charge.

Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of f tank body with the help of stencil and paint and disposing of malba all complete as per direction of Engineer-in- Charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stencil or old date is not removed deduction will be made @ Rs. 0.10 per litre) (if during cleaning any GI fittings or ball cock is damaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account)

Cleaning and desilting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer- incharge.

Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.

Bars upto 12 mm diameter

Bars above 12 mm diameter

Drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in RCC beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of Engineer-In-Charge.

Upto and including 12mm dia

Providing and injecting approved grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete/masonry by suitable gun/ pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-Charge. (The payment shall be made on the basis of actual weight of approved grout injected.)

Stirrer mixed Acrylic Polymer of approved make @ 2% of weight of cement used) modified Cement slurry made with non shrink compound in concrete/RCC work

Stirrer mixed SBR Polymer (of approved make) modified Cement slurry made with Shrinkage Compensating Cement in concrete/RCC work.

Epoxy injection grout in concrete/RCC work of approved make

Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.

Providing and fixing hard drawn steel wire fabric of size 75 x25 mm mesh or other suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of "L" shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by Engineer-incharge.

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix).

Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix).

In lime mortar.

In cement mortar.

From brick work in lime mortar.

From brick work in cement mortar.

In lime mortar.

In cement mortar.

In lime mortar.

In cement mortar.

Removing mortar from and cleaning stones and concrete articles (net quantity of stacks of cleaned materials will be measured) :

In lime mortar.

In cement mortar.

For thickness of tiles 10 mm to 25 mm.

For thickness of tiles above 25 mm and upto 40 mm.

Of area 3 sq. metres and below.

Of area beyond 3 sq. metres.

Of area 3 sq. metres and below.

Of area beyond 3 sq. metres.

Of sectional area below 40 square centimetres.

Of sectional area 40 square centimetres and above.

Of sectional area below 40 square centimetres.

Of sectional area 40 square centimetres and above.

Of sectional area below 40 square centimetres.

Of sectional area 40 square centimetres and above.

R.S. Joists

Channels, angles, tees and flats

Dismantling steel work in built up sections with span upto 10 meter and hieght 5 meter in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50metres lead.

G.S. Sheet

Asbestos/ Non asbestors sheet

Dismantling wooden ballies in posts and struts including stacking within 50 metres lead.

T’ or ‘L’ iron or pipe

Upto 10 mm thick

Thickness above 10 mm upto 25 mm

Thickness above 25 mm upto 40 mm

Thickness upto 40 mm

Thickness above 40 mm upto 75 mm

75 to 80 mm dia pipe.

100 mm dia pipe

150 mm dia pipe

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-Charge :

15 mm to 40 mm nominal bore

Above 40 mm nominal bore

Upto 150 mm diameter

Above 150 mm dia upto 300 mm dia.

Above 300 mm diameter

Upto 150 mm diameter

Above 150 mm diameter

Dismantling of old S.W. pipes including breaking of joints and bed concrete stacking of useful materials near the site within 50 m lead and disposal of unserviceable materials into municipal dumps:

100 mm diameter

150 mm diameter

200 mm diameter

250 mm diameter

300 mm diameter

350 mm diameter

400 mm diameter

440 mm diameter

Rectangular manhole 90x80 cm and 45 cm deep

Rectangular manhole 120x90 cm and 90 cm deep.

Rectangular arch type manhole 140x90cm and 2.45m deep.

Circular manhole 122 cm diameter and 1.68 m deep

Rectangular manhole 90x80 cm and beyond 45 cm depth.

Rectangular manhole 120x90 cm and beyond 90 cm depth.

Rectangular arch type manhole 140x90 cm and beyond 2.45m deep (upto 4.25 m depth).

Circular manhole 122 cm diameter and beyond 1.68 m deep (upto 2.29 m depth).

Water bound macadam road

Bituminous road

Up to 600 mm diameter

Above 600 mm diameter

Dismantling asbestos cement pressure pipes including excavation and refilling trenches after taking out the pipes manually/ by mechanical means and stacking the pipes within 50 metres lead as per direction of Engineer-in-charge

Up to 150 mm diameter

Above 150 mm diameter

120 x 120 cm (outside to outside)

210 x 120 cm (outside to outside)

White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests.

Stainless Steel AISI-304(18/8) Orissa pattern W.C. pan of size 585x480 mm with flush pipe and integrated type foot rests.

W.C. pan with ISI marked white solid plastic seat and lid

W.C. pan with ISI marked black solid plastic seat and lid

Providing and fixing AISI-304 (18/8) European type WC instead of white vitreous china pedestal type water closet.

W.C. pan with ISI marked white solid plastic seat and lid.

W.C. pan with ISI marked black solid plastic seat and lid.

One urinal basin with 5 litre white P.V.C. automatic flushing cistern.

Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern.

Range of three urinal basins with 10 litre white P.V.C. automatic flushing cistern.

Range of four urinal basins with 10 litre white P.V.C. automatic flushing cistern.

Single half stall urinal with 5 litre P.V.C. automatic flushing cistern.

Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern.

Range of three half stall urinals with 10 litre P.V.C. automatic flushing cistern.

Range of four half stall urinals with 10 litre P.V.C. automatic flushing cistern.

Single squatting plate with 5 litre P.V.C. automatic flushing cistern.

Range of two squatting plates with 5 litre P.V.C. automatic flushing cistern.

Range of three squatting plates with 10 litre P.V.C. automatic flushing cistern.

Range of four squatting plates with 10 litre P.V.C. automatic flushing cistern.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre and post flushing with water ( 250 ml and 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-Charge.

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.

White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap.

White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps.

White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap.

White Vitreous China Angle back wash basin size 600x480 mm with single 15 mm C.P. brass pillar tap.

White Vitreous China Angle back wash basin size 400x400 mm with single 15 mm C.P. brass pillar tap.

White Vitreous China Flat back wash basin size 450x300 mm with single 15 mm C.P. brass pillar tap.

White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow operated lever ISI marked.

White Vitreous China Surgeon type wash basin of size 660x460 mm with single 15 mm C.P. brass pillar taps with elbow operated levers ISI marked.

Oval shape wash basin over counter /under counter with 15 mm C.P brass pillar tap (Counter to be paid sepratly).

Stainless Steel AISI-304(18/8) Round basin 405x355 mm with single 15 mm C.P. brass pillar tap

Stainless Steel AISI-304(18/8) Wash basin 530x345 mm with single 15 mm C.P. brass pillar tap.

Kitchen sink with drain board

510x1040 mm bowl depth 250mm.

510x1040 mm bowl depth 225mm.

510x1040 mm bowl depth 200mm.

510x1040 mm bowl depth 178mm.

Kitchen sink without drain board

610x510 mm bowl depth 200 mm.

610x460 mm bowl depth 200 mm.

470x420 mm bowl depth 178 mm.

Size450x300x150mm

Size600x450x200mm

Long pattern W.C. pan of size 580 mm

Orissa pattern W.C. pan of size 580x440 mm

Extra for using coloured pedestal type W.C pan (European type) with low level cistern of same colour instead of white vitreous china W.C pan and cistern.

White

coloured

White

Coloured

White

Black

Coloured (other than black and white)

Flat back wash basin of size 630x450mm.

Flat back wash basin of size 550x400mm.

Angle back wash basin of size 600x480mm.

Angle back wash basin of size 400x400mm.

Flat back wash basin of size 450x300mm.

Surgeon type wash basin of size 660x460mm.

Providing and fixing kitchen sink including making all connections excluding cost of fittings. White glazed fire clay sink of size 600x450x250mm.

Size 450x300x150 mm.

Size 600x450x200 mm.

Sand cast iron socket and spigot (S&S) pipe as per IS: 1729

75 mm dia with wall thickness of 5 mm

100 mm dia with wall thickness of 5 mm

Spun cast iron socket and spigot (S&S) pipe as per IS: 3989

75 mm dia with wall thickness of 3.5 mm

100 mm dia with wall thickness of 4 mm

150mm dia with wall thickness of 5mm

Hubless Centrifugally cast (spun) iron pipe epoxy coated in side & out side including complete coupling assembly (EPDM rubber gasket stainless steel claim and external metallic/ protective shield as per IS:15905)

75 mm dia with wall thickness of 3.5 mm

100 mm dia with wall thickness of 3.5mm

150mm dia with wall thickness of 4 mm

75 mm dia pipe

100 mm dia pipe

For 75 mm dia pipe

For 100 mm dia pipe

For 150 mm dia pipe

150 mm dia

Sand cast iron as per IS – 1729 minimum wall thickness 6.5mm

Spun cast iron as per IS – 3989 minimum wall thickness 5 mm

Hubless cast(spun) iron as per IS- 15905 minimum wall thickness 3.5 mm

100 mm dia

Sand cast iron as per IS – 1729 minimum wall thickness 6.5mm

Spun cast iron as per IS – 3989 minimum wall thickness 4 mm

Hubless cast(spun) iron as per IS- 15905 minimum wall thickness 3 mm

75 mm dia

Sand cast iron as per IS – 1729 minimum wall thickness 6.5 mm

Spun cast iron as per IS – 3989 minimum wall thickness 3.5 mm

Hubless cast(spun) iron as per IS- 15905 minimum wall thickness 3 mm

150 mm dia

Sand cast iron as per IS – 1729 minimum wall thickness 6.5mm

Spun cast iron as per IS – 3989 minimum wall thickness 5 mm

Hubless cast(spun) iron as per IS- 15905 minimum wall thickness 3.5 mm

100 mm dia

Sand cast iron as per IS – 1729 minimum wall thickness 6.5mm

Spun cast iron as per IS – 3989 minimum wall thickness 4 mm

Hubless cast(spun) iron as per IS- 15905 minimum wall thickness 3 mm

75 mm dia

Sand cast iron as per IS – 1729 minimum wall thickness 6.5mm

Spun cast iron as per IS – 3989 minimum wall thickness 3.5 mm

Hubless cast(spun) iron as per IS- 15905 minimum wall thickness 3 mm

100 mm dia

Sand cast iron as per IS - 1729

Spun cast iron as per IS - 3989

75 mm dia

Sand cast iron as per IS - 1729

Spun cast iron as per IS - 3989

Sand cast iron as per IS - 3989

100x100x100x100mm

Sand cast iron as per IS - 1729

Spun cast iron as per IS - 3989

75x75x75x75mm

Sand cast iron as per IS - 1729

Spun cast iron as per IS - 3989

150X150X150X150 mm

Sand cast iron as per IS - 3989

100x100x100x100mm

Sand cast iron as per IS – 1729

Spun cast iron as per IS – 3989

Hubless cast(spun) iron as per IS- 15905

75x75x75x75 mm

Sand cast iron as per IS – 1729

Spun cast iron as per IS – 3989

Hubless cast(spun) iron as per IS- 15905

Providing and fixing single equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

Spun cast iron as per IS - 3989

Sand cast iron as per IS - 1729

Spun cast iron as per IS - 3989

Sand cast iron as per IS - 1729

Spun cast iron as per IS - 3989

Spun cast iron as per IS - 3989

Sand cast iron as per IS – 1729

Spun cast iron as per IS – 3989

Hubless cast(spun) iron as per IS- 15905

Sand cast iron as per IS – 1729

Spun cast iron as per IS – 3989

Hubless cast(spun) iron as per IS- 15905

Sand cast iron as per IS - 1729

Spun cast iron as per IS - 3989

Sand cast iron as per IS – 1729

Spun cast iron as per IS – 3989

Hubless cast(spun) iron as per IS- 15905

Sand cast iron as per IS - 1729

Spun cast iron as per IS - 3989

Sand cast iron as per IS – 1729

Spun cast iron as per IS – 3989

Hubless cast(spun) iron as per IS- 15905

100x100x100x100 mm

Sand cast iron as per IS - 1729

Sand cast iron as per IS - 3989

Hubless cast(spun) iron as per IS- 15905

75x75x75x75 mm

Sand cast iron as per IS - 1729

Spun cast iron as per IS - 3989

Sand cast iron as per IS - 1729

Sand cast iron as per IS - 3989

Hubless cast(spun) iron as per IS- 15905

Sand cast iron as per IS - 1729

Sand cast iron as per IS - 3989

Hubless cast(spun) iron as per IS- 15905

Sand cast iron as per IS - 1729

Spun cast iron as per IS - 3989

Sand cast iron as per IS - 1729

Spun cast iron as per IS - 3989

Hubless cast(spun) iron as per IS- 15905 minimum wall thickness

Providing and fixing sand cast iron S&S off sets as per IS: 1729

76 mm off sets

With 75 mm dia pipe

With 100 mm dia pipe

114 mm off sets

With 75 mm dia pipe

With 100 mm dia pipe

152 mm off sets

With 75 mm dia pipe

With 100 mm dia pipe

75 mm off sets

With 75 mm dia pipe

With 100 mm dia pipe

With 150 mm dia pipe

150 mm off sets

With 75 mm dia pipe

With 100 mm dia pipe

With 150 mm dia pipe

Sand cast iron as per IS - 1729

Spun cast iron as per IS - 3989

Sand cast iron as per IS - 1729

Spun cast iron as per IS - 3989

Sand cast iron as per IS - 1729

Spun cast iron as per IS - 3989

Hubless cast(spun) iron as per IS- 15905

Sand cast iron as per IS - 1729

Spun cast iron as per IS - 3989

Hubless cast(spun) iron as per IS-15905

Sand cast iron as per IS - 1729

Spun cast iron as per IS - 3989

Hubless cast(spun) iron as per IS- 15905

Sand cast iron S & S as per IS - 1729

Sand cast iron S & S as per IS - 3989

Sand cast iron S & S as per IS - 1729

Sand cast iron S & S as per IS- 3989

100 mm dia

75 mm dia

100 mm inlet and 100 mm outlet

Spun cast iron S & S as per IS: 3989.

Sand Cast iron S & S as per IS: 1729.

Hubless cast(spun) iron as per IS-15905

100 mm inlet and 75 mm outlet

Sand cast iron S & S as per IS - 3989

Spun Cast iron S & S as per IS- 1729.

Hubless cast(spun) iron as per IS- 15905

75 mm diameter

110 mm diameter

Coupler

Single pushfit Coupler

Single tee with door

Single tee without door

75 mm bend

110 mm bend

Providing and fixing Unplasticised - PVC pipe clips of approved design to Unplasticised - PVC soil and waste pipes by means of bombay nail of required length including and making good the wall etc. complete.

Total bracket length 580mm of approved shape and design (for single, 100mm dia pipe).

Total bracket length 810mm of approved shape and design (for two, 100mm dia pipes).

Total bracket length 1040mm of approved shape and design (for three, 100mm dia pipes).

100 mm dia

75 mm dia

50 mm dia

Semi rigid pipe

32 mm dia

40 mm dia

Flexible pipe (only in residential & complaxes)

32 mm dia

40 mm dia

Circular shape 450mm dia.

Rectangular shape 453x357mm

Oval shape 450x350mm (outer dimensions)

Rectangular shape 1500x450 mm

Providing and fixing toilet paper holder:

C.P. brass

Vitreous china

Waste coupling 31mm of 79mm length and 62mm breadth

Waste coupling 38mm of 83mm length and 77mm breadth

100 mm dia.

Waste coupling 31mm dia of 79mm length and 62mm breadth weighing not less than 45gms.

Waste coupling 38mm dia of 83mm length and 77mm breadth, weighing not less than 60gms.

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Bottle trap 31mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 260gms.

Bottle trap 38mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighting not less than 263gms.

450mm long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170gms.

600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms.

Repainting C.I. cistern with synthetic enamel paint of approved colour brand and manufacture on the outside surface of cistern flush pipe, other fittings etc. complete.

75 mm diameter pipe

100 mm diameter pipe

150 mm diameter pipe

75 mm diameter pipe

100 mm diameter pipe

150 mm diameter pipe

100 mm dia half round pipe

150 mm dia half round pipe

200mm dia half round pipe

For ground floor buildings.

For Ground floor & Ist floor buildings.

Add extra for every additional floor above Ist floor.

Internal work - Exposed on wall

15 mm nominal outer dia Pipes.

20 mm nominal outer dia .Pipes.

25 mm nominal outer dia .Pipes.

32 mm nominal outer dia Pipes.

40 mm nominal outer dia Pipes.

50 mm nominal outer dia .Pipes.

Concealed work including cutting chases and making good the walls etc.

15 mm nominal outer dia .Pipes.

20 mm nominal outer dia .Pipes.

25 mm nominal outer dia Pipes.

32 mm nominal outer dia Pipes.

External Work

15 mm nominal outer dia Pipes.

20 mm nominal outer dia .Pipes.

25 mm nominal outer dia Pipes.

32 mm nominal outer dia .Pipes.

40 mm nominal outer dia Pipes.

50 mm nominal outer dia .Pipes.

62.50 mm nominal inner dia Pipes.

75 mm nominal inner dia .Pipes.

100mm nominal inner dia .Pipes.

150 mm nominal inner dia Pipes.

Internal work - Exposed on wall

15 mm dia. nominal bore

20 mm dia. nominal bore

25 mm dia. nominal bore

32 mm dia. nominal bore

40 mm dia. nominal bore

50 mm dia. nominal bore

Concealed pipe including painting with anti corrosivebitumastic paint, cutting chases and making good the wall.

15 mm dia nominal bore

20 mm dia nominal bore

External work : including trenching and refilling etc.

15 mm dia. nominal bore

20 mm dia. nominal bore

25 mm dia. nominal bore

32 mm dia. nominal bore

40 mm dia. nominal bore

50 mm dia. nominal bore

65 mm dia. nominal bore

80 mm dia. nominal bore

Internal work - Exposed on wall

15.88 mm outer diapipe

28.58 mm outer diapipe

34.00 mm outer dia Pipe

42.70 mm outer dia Pipe

48.60 mm outer dia Pipe

Internal work - Concealed Pipe

15.88 mm outer dia .Pipes.

22.22 mm Outer diaPipes

With C.I. wheel of approved quality (screwed end)

25 mm nominal bore

32 mm nominal bore.

40 mm nominal bore

50 mm nominal bore

65 mm nominal bore

80 mm nominal bore

With brass lever handle of approved quality.

25 mm nominal bore

32 mm nominal bore.

40 mm nominal bore

50 mm nominal bore

25 mm nominal bore

32 mm nominal bore.

40 mm nominal bore

50 mm nominal bore

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

Horizontal

Vertical

32 mm nominal bore

Horizontal

Vertical

40 mm nominal bore

Horizontal

Vertical

50 mm nominal bore

Horizontal

Vertical

65 mm nominal bore

Horizontal

Vertical

80 mm nominal bore

Horizontal

Vertical

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

30 cm length

15 mm nominal bore

20 mm nominal bore

45 cm length

15 mm nominal bore

20 mm nominal bore

With common burnt clay bricks of 25 kg /sqcm compressive strength.

With well burnt flyash bricks of 50 kg/sqm compressive strength.

With common burnt clay bricks of 25 kg /sqcm compressive strength.

With flyash bricks of 50 kg/cm2 strength

Constructing masonry Chamber 60x60x75 cm, inside in brick work in cement mortar 1:4 (1 cement : 4 sand) for fire hydrants, with C.I. surface box 350x350 mm. top and 165 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :

With common burnt clay bricks of 25 kg/cm2 compressive strength.

With flyash bricks of 50kg/cm2 strength.

With common burnt clay bricks of 25 kg /sqcm compressive strength.

With flyash bricks of 50kg/sqm compressive strength.

15 mm diameter pipe.

20 mm diameter pipe.

25 mm diameter pipe.

32 mm diameter pipe.

40 mm diameter pipe.

50 mm diameter pipe.

15 mm diameter pipe.

20 mm diameter pipe.

25 mm diameter pipe

32 mm diameter pipe

40 mm diameter pipe

50 mm diameter pipe

15 mm diameter pipe

20 mm diameter pipe

25 mm diameter pipe

32 mm diameter pipe

40 mm diameter pipe

50 mm diameter pipe

65 mm diameter pipe

80 mm diameter pipe

15 mm diameter pipe

20 mm diameter pipe

25 mm diameter pipe

32 mm diameter pipe

40 mm diameter pipe

50 mm diameter pipe

65 mm diameter pipe

80 mm diameter pipe

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50mm nominal bore

65mm nominal bore

80 mm nominal bore

15 mm nominal bore.

20 mm nominal bore.

25 mm nominal bore.

32 mm nominal bore.

40 mm nominal bore.

50 mm nominal bore.

65 mm nominal bore.

80 mm nominal bore.

15 mm nominal bore

20 mm nominal bore

Providing and fixing brass stop cock of approved quality :

15 mm nominal bore

20 mm nominal bore

Providing and fixing C.P. brass sink mixer of approved quality and make conforming to IS: specification. 15 mm nominal bore.

100 mm diameter

150 mm diameter

200 mm diameter

86 mm long weighing not less than 88 gm

122 mm long weighing not less than 99 gm

165mm long weighing not less than 110 gm

90mm long weighing not less than 93 gm

15 mm nominal bore, 86mm long. Weighing not less than 88 gms.

20mm nominal bore, 89mm long. Weighing not less than 88 gms.

Concealed stop cock, 15mm nominal bore, 108mm long. Weighing not less than 108 gms.

15mm nominal bore, 107mm long. Weighing not less than 110 gms.

15mm nominal bore, 125mm long foam flow weighing not less than 120 gms.

15 mm nominal bore, 98mm long. Weighing not less than 75 gms.

15 mm nominal bore, 80mm long weighing not less than 46 gms.

Circular type.

100 mm nominal dia.

125 mm nominal dia with 25 mm waste hole.

Rectangular type with openable circular lid.

150 mm nominal size square 100 mm diameter of the inner hinged round grating.

Providing and fixing PTMT swivelling shower, 15mm nominal bore. Weighing not less than 40gms.

15 mm nominal bore, 105 mm long. Weighing not less than 138 gms.

20 mm nominal bore, 120 mm long. Weighing not less than 198 gms.

25 mm nominal bore, 152mm long. Weighing not less than 440 gms.

40mm nominal bore, 206mm long. Weighing not less than 690 gms.

50mm nominal bore, 242mm long. Weighing not less than 1240 gms.

30cm length.

45 cm length.

15 mm nominal bore.Weighing not less than 32 gms.

20mm nominal bore.Weighing not less than 40gms.

25mm nominal bore.Weighing not less than 62 gms.

80 mm nominal bore

100 mm nominal bore

150 mm nominal bore

200 mm nominal bore

80 mm nominal bore

100 mm nominal bore

150 mm nominal bore

200 mm nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :

25 to 40 mm nominal bore

50 to 80 mm nominal bore

100 mm diameter

150 mm diameter

200 mm diameter

230 mm diameter

250 mm diameter

300 mm diameter

100 mm diameter S.W. pipe

150 mm diameter S.W. pipe

200 mm diameter S.W. pipe

230 mm diameter S.W. pipe

250 mm diameter S.W. pipe

300 mm diameter S.W. pipe

100 mm diameter S.W. pipe

150 mm diameter S.W. pipe

200 mm diameter S.W. pipe

230 mm diameter S.W. pipe

250 mm diameter S.W. pipe

300 mm diameter S.W. pipe

110 mm diameter OD (min. wall thickness 3.2mm)

160 mm diameter OD (min. wall thickness 4.0mm)

200 mm diameter OD (min. wall thickness 4.9mm)

250 mm diameter OD (min. wall thickness 6.2mm)

300 mm diameter OD (min. wall thickness 7.7mm)

110 mm diameter PVC. pipe

160 mm diameter PVC. pipe

200 mm diameter PVC. pipe

250 mm diameter PVC. pipe

300 mm diameter PVC pipe

110 mm diameter PVC. pipe

160 mm diameter PVC. pipe

200 mm diameter PVC. pipe

250 mm diameter PVC. Pipe

300 mm diameter PVC pipe

100x100 mm size P type

With well burnt bricks

With Sewer bricks conforming to IS : 4885

150 x 100 mm size P type.

With well burnt bricks

With sewer bricks conforming to IS : 4885

180x150 mm size P type

With well burnt bricks

With Sewer bricks conforming to IS : 4885

100 mm dia. R.C.C. pipe

150 mm dia. R.C.C. pipe

250 mm dia. R.C.C. pipe

300 mm dia. R.C.C. pipe

450 mm dia. R.C.C. pipe

500 mm dia. R.C.C. pipe

600 mm dia. R.C.C. pipe

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

With well burnt bricks

With Sewer bricks conforming to IS : 4885

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) :

With well burnt bricks

With Sewer bricks conforming to IS : 4885

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) :

With well burnt bricks

With Sewer bricks conforming to IS : 4885

Extra for depth for manholes

Size 90x80 cm

With well burnt bricks

With Sewer bricks conforming to IS : 4885

Size 120x90 cm

With well burnt bricks

With Sewer bricks conforming to IS : 4885

With well burnt bricks

With Sewer bricks conforming to IS : 4885

With well burnt bricks

With Sewer bricks conforming IS : 4885

With well burnt bricks

With Sewer bricks conforming IS : 4885

With well burnt bricks

With Sewer bricks conforming IS : 4885

2.30m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) including centering shuttering all complete. (Foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :

With well burnt bricks

With Sewer bricks conforming IS : 4885

With well burnt bricks

With Sewer bricks conforming IS : 4885

With 20x20 mm square bar

With 20 mm diameter round bar

With 20x20 mm square bar

With 20 mm diameter round bar

Supplying and fixing C.I. cover without frame for manholes :

455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg.

500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg.

560 mm diameter C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg.

Light duty D- 2.5

Rectangular shape 600x450mm internal dimensions

Square shape 450mm internal dimensions

Circular shape 450mm internal diameter

Medium duty - 10

Square shape 450mm internal dimension

Circular shape 500mm internal diameter

Heavy duty D - 20

Circular shape 560 mm internal diameter

Extra Heavy Duty - 35

Circular shape 560 mm internal dia.

For pipes 100 to 230 mm diameter

For pipes 250 to 300 mm diameter

For pipes 350 to 450 mm diameter

100 mm dia. sand cast iron drop connection

150 mm dia. sand cast iron drop connection

For 100 mm dia. sand cast iron drop connection

For 150 mm dia. sand cast iron drop connection

Rectangular manhole 90x80 cm with rectangular cover 600x450 mm of grade LD - 2.5

Rectangular manhole 120x90 cm with circular cover 500 mm dia of grade MD - 10

Rectangular manhole 120x90 cm with circular cover 560 mm dia of grade HD - 20

Circular manhole 140 cm dia with circular cover 600 mm dia of grade Extra heavy duty HD -35

With well burnt bricks

With fly ash bricks 100 key/cm2 strangth

With well burnt bricks

With fly ash bricks 100 kg/cm2 strength

With well burnt bricks

With fly ash bricks 100 kg/cm2 strength

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

With well burnt bricks

100 mm dia

150 mm dia

100 mm dia

150 mm dia

200 mm dia

230 mm dia

250 mm dia

300 mm dia

100 mm dia. Half round R.C.C. pipe

150 mm dia. Half round R.C.C. pipe

250 mm dia. Half round R.C.C. pipe

300 mm dia. Half round R.C.C. pipe

Deduct for not provide C.I. manhole cover with frame for item No. 19.9.2.1 & 19.9.2.2

Deduct for not provide C.I. manhole cover with frame for item No. 19.9.3.1 & 19.9.3.2

Supplying and fixing of FRP/GRP composite manhole cover with frame of clear opening size 900X450mm rectangular having weight of (complete unit) (weight of frame 11.7 kg + weight of cover 43.76kg ± 10%) (HD/25MT) having load bearing capacity (Point load 25MT) as per testing code BSEN 124:1994. Having lifting arrangement should have an insertion of 5mm double sealed closed key hole and high strength plastic alloy/stainless steel socketed arrangement.

900mmx450mm (weight of cover 43.76kg ± 10%)

450mmx600mm (weight of cover 14.2kg ± 10%)

300mmx300mm (weight of cover 4.1kg ± 10%)

600mm (weight of cover 41.78kg ± 10%)

500mm (weight of cover 43.1kg ± 10%)

100 mm dia to 110 mm dia

150 mm dia to 160 mm dia

200 mm dia

250 mm dia

300 mm dia

For fixed portion.

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC15)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

For shutters of doors, windows and ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately).

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC15)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Deduct for not providing EDPM rubber/neoprene gasket all around.

Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

Pre-laminated particle board with decorative lamination on both sides.

With float glass panes of 4.0 mm thickness (weight not less than 10 kg/sqm)

With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg/sqm )

With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm ).

With glass panes of 4.0 mm thickness (weight not less than 10 kg/sqm)

With glass panes of 5.0 mm thickness (weight not less than 12.50 kg/sqm )

With glass panes of 8 mm thickness (weight not less than 20 kg/sqm ).

With stainless steel cover plate - minimum 1.25 mm thickness

With brass cover plate - minimum 1.25 mm thickness.

Anodised aluminium sheet 2.5mm thick (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Powder coated aluminium sheet 2.5mm thick (minimum thickness of powder coating 50 micron)

Extra for applying additional anodic coating AC 25 instead of AC 15 to aluminium extruded sections. For fixed portion & for shutters of doors, windows and ventilators

Anodized (AC 15 ) aluminium tubular handle bar

Powder coated minimum thickness 50 micron aluminium tubular handle bar.

Polyester powder coated minimum thickness 50 micron aluminium tubular handle bar.

Anodized (AC15) aluminium

Powder coated minimum thickness 50 micron aluminium.

Polyester powder coated minimum thickness 50 micron aluminium.

Anodized (AC15 ) aluminium

Powder coated minimum thickness 50 micron aluminium

Polyester powder coated minimum thickness 50 micron aluminium.

Providing and fixing 50 micron thick Frosted heat /light control film to window/door glazing with complete accessories as per direction of Engineer-in-charge of approved brand and make.

(i) Ist layer of 22mm to 25mm thick approved and specified rough stone slab over a 25mm thick base of cement mortar 1:3 (1 cement: 3 sand) mixed with water proofing compound conforming to IS: 2645 in the recommended proportion over the levelling course ( levelling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound.

(ii) 2nd layer of 25mm thick cement mortar 1:3 (1 cement: 3 sand) mixed with water proofing compound in recommended proportions.

(iii) Finishing top with stone aggregate of 10mm to 12mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer. (with 5 years service guarantee) Using rough Kota stone.

a) Ist course of applying cement slurry @ 4.4 Kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.

b) IInd course of 20mm cement plaster 1:3 (1 cement: 3 sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.

c) IIIrd course of applying blown or residual bitumen applied hot at 1.7 Kg. per sqm of area.

d) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/sqm.) (with 5 years service guarantee)

Serrated with central bulb (225mm wide, 8- 11mm thick).

Dumb bell with central bulb (180mm wide, 8mm thick).

Kickers (320mm wide, 5mm thick).

a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours.

b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

a) After surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm.

b) Laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm.

c) Third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around.

a) Applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment.

b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-Charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-Charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

c) After two days of proper curing applying a second coat of cement slurry using 2.75kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-Charge.

d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement: 4 sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3mm deep.

e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in- Charge: (with 5 years service guarantee) With average thickness of 120mm and minimum thickness at khurra as 65 mm.

Providing and laying six courses water proofing treatment with bitumen felt over roofs consisting of first, third and fifth courses of blown or / and residual bitumen applied hot at 1.45, 1.20 and 1.70 kg per square metre of area respectively, second and fourth courses of roofing felt type 2 grade I (fibre base self finished bitumen felt) six and final courses of stone grit 6 mm and down size or pea sized gravel spread at 6cu.dm per sqm including preparation of surface, excluding grading, complete. (With five years service gurantee).

Cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size)

Cement mortar 1:3 (1 cement : 3 sand)

Cement mortar 1:4 (1cement : 4 sand)

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 ltr/sqm. by the same membrane manufacture of density at 23°C as 650/450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane: (with 5 years service guarantee).

(i) Surface preparation roughening of surface, opening cracks in ‘V’ groove in size of 5mmX10mm (WXD), filling of cracks with putty with laying fiber glass mesh, Cleaning of surface by scrubbing with steel wire/Nylon brush. Removing all dust particles and washing with adequate water to clean completely.

(ii) Providing and applying 1st coat of fibre glass mesh (minimum thicknes 70-80 micron) and two component flexible waterproof and protective modified mortar, dry powder 80% chemical 20% acrylic resin having 30% solid contents) with mix proportion of part 1 and 2 with proper mixing with laying of fiber glass mesh (of weaving size of 10X10 yarn/inch duly coated with alkaline resistant polymer). Allow the coating to air cure for minimum 2 Hrs. After two hours of 1st coat applying 2nd coat (minimum thickness 100 micron) of fibre glass mesh of with mix proporation of part 1 and 2 with proper mixing. Allow the coating to air cure for minimum 2 hrs. Consumption of two component should be acrylic resin @17.90 kg for 10 sqm area or as per manufacture instructions. (After two coats of diamond shield, surface is to be cured properly minimum for 4 hrs. before application of third coat).

(iii) Providing and applying 1st coat of sealer coat 50-60 micron (single component Hight build elastomeric, fixable pure acrylic waterproofing membrane having solid content of 65%) and allow it to air cure for 4Hrs. minimum. After two hours minimum of 1st coat applying 2nd and finals coat 120-140 micron of sealer coat and allow it to air cure for 4 Hrs mimimum. Consumption of Sealer coat should be @ 5.40 kg per 10 sqm area.

(iv) The treated area should be cure with water for 48 hrs. by flooding the surface.

(v) The final appearance of the coating will be milky white. All above operations to be done in order.(five years guarantee)

(i)Removal of damaged waterproofing treatment if any like bituminous membrane / plaster/ brick bat koba/screeding etc.

(ii) Surface preparation: Roughening of surface by scrubbing with steel wire/ Nylon brush/ Removing all dust particles and washing with adequate water to clean completely, opening of cracks in 'V' groove in size of 5mm x 10m (WxD), filling of cracks with elastomeric creak filler/PU sealent repair of potholes and holor making on roof surface by polymer mortar with adding SBR bonding agent.

(iii) Providing and applying 1st coating of rubberized elastomeric liquid membrane as primer (ratio 1:2 1 part liquid membrane and 2 part water) by brush/ Roller/ Spray having minimum thickness of 70-80 micron. Allow the coating to set in natural air for minimum 2 hrs, then put reinforcement by laying 45gsm fibre glass mesh and applying 2nd coat of rubberized elastomeric liquid membrane (Ratio: 1 part membrane and 20% water) with minimum thickness 100-120 micron. Allow the coating to set in natural air for minimum 12 hrs.

(iv) Providing and applying 3rd coat of rubberized elastomeric liquid membrane (Ratio: 1 part membrane and 10% water). Total DFT (Dry film thickness) thickness after 3rd coat must be 280-300 micron and consumption in three coats @ 6.5kg for 10sqm.

(v) Providing and applying 4th and 5th coat of High quality waterproof membrane in white colour, single component special synthetic resin based flexible thixotropic white color coating with excellent UV resistance (SRI - 144) with more than 300% elongation (confirming ASTM D 412-98) in ratio: 1 part membrane and 10% water thickness of 200 micron DFT in two coats, with average consumption @ 5kg per 10 sqm. After application of fourth coat let it air dry for minimum 3 hrs before application of fifth coat.

(vi) The treated area must be tested for water leakage/seepage by flooding with water for 48 hrs

(vii) Application of membrane coating shall be got done by authorized applicator of manufacturer.

(viii) 5 years of service guarantee to be provided. All above operations to be done in order as per direction on Engineer-in-Charge.

a) Resist hydrostatic pressure of up to 70 m head of water as per ASTM D5385;

b) Puncture Resistance of 950 N (as per ASTM E154)

c) Elongation of >400 % (as per ASTM D412)

d) Peel Strength of concrete: >1500 N/m (as per ASTM D903)

e) Tensile strength of 28.2 MPA (as per ASTM D412).

Providing & applying crack fill paste for crack filling up to 5 mm cracks.Widen the crack by putty knife in V/U shape & apply 1st priming coat of crack fill paste diluted with water in 1:1 proportion over the crack by brush. Apply 2nd coat with filling of crack fill paste when the surface is tacky but not dried completely with putty knife & spatula.After 4 hours of application 2nd coat apply 3rd coat of Crack fill paste. The work shall be carried out as recommended by the manufacturer’s specification & the direction of the Engineer-in-Charge

For Horizontal surface (with Geotextile fleece) two coats without dilution & 1 Self priming coat- 50% dilution with water @ 10 kg/m2

For Horizontal surface (without Geotextile fleece) two coats without dilution & 1 Self priming coat- 50% dilution with water @ 10 kg/m2

For vertical surface two coats @ 0.70 kg per sqm

For horizontal surface one coat @1.10 kg per sqm.

For sealing cracks and faulty construction joints, routed out/making U-shape groove size 25x25mm and then primed the area with integral crystalline slurry @0.05kg/ running metre and while the surface is tacky filled the groove upto surface with crystalline mortar @1.50kg/ running metre. Once crystalline mortar is touch dry then finally applied two coats of integral crystalline slurry @0.05kg/running metre per coat.

For patching of tie rod holes, prepared tie rod hole surface and then primed the area with integral crystalline slurry @ 0.070 kg/sqm and while the surface is tacky repair and then filled the tie rod holes with crystalline mortar @ 0.040 kg per hole. The crystalline mortar should be tightly rodded into tie rod holes or packed tightly (For 25x25x25 mm tie rod hole, use 0.040 kg to fill the hole)

Providing and fixing insulation with resin bonded Glass wool

Providing and fixing insulation with resin bonded Rock wool

Ridges plain (500 - 600mm).

Flashings/ Aprons.( Upto 600 mm)

North light curves.

Barge board (Upto 300 mm).

Crimp curve

Gutter. (600 mm over all girth).

White Vitreous china Anti germ Fluoro-Polymer coated Orissa Pattern W. C. Pan of Size 440x575x250 mm With integral foot rests. (Premium Range)

White Vitreous china Anti germ Fluoro-Polymer coated Orissa pattern W. C. pan of size 410x515x255 mm with integral foot rests. (Premium Range)

Anti-germ Fluoro-Polymer Coated (nano coating) European W. C. pan size 360x545x395 mm with solid poly propelyne made soft closing seat cover (Premium Range)

Anti-germ Fluoro-Polymer Coated Water Closet European type W. C. pan size 360x545x395 mm with solid poly propelyne made soft closing seat cover (Premium Range)

Anti germ Fluoro-Polymer Coated (Nano coating) Wall hung water closet Size 380x520x375 mm with solid poly propelyne made soft closing seat cover (Premium Range)

Anti germ Fluoro-Polymer Coated (Nano coating) Wall hung water closet size 390x570x365 mm with solid poly propelyne made, soft closing seat cover (Premium Range)

Anti germ Fluoro-Polymer Coated (Nano coating) Wall hung water closet size 360 x 500x360 mm with solid poly propelyne made, soft closing seat cover (Premium Range)

Anti germ Fluoro-Polymer Coated (Nano coating) Wall hung water closet size 360x500x330 mm or greater size with solid poly propelyne made, soft closing seat cover (Premium Range)

Anti germ Fluoro-Polymer Coated couple water closet Size 420x710x810 mm with solid poly propelyne made soft closing seat cover. (Premium Range)

Anti germ Fluoro-Polymer Coated couple water closet Size 380x610x805 mm with solid poly propelyne made soft closing seat cover. (Premium Range)

Anti germ Fluoro-Polymer Coated couple water closet Size 370 x 640 x 760mm with solid poly propelyne made soft closing seat cover. (Premium Range)

Anti germ Fluoro-Polymer Coated couple water closet Size 375 x 650 x 800 mm with solid poly propelyne made soft closing seat cover. (Premium Range)

Anti germ Fluoro-Polymer Coated Single Piece W.C. Pan Size 370x695x795 mm with solid poly propelyne made soft closing seat cover.(Premium Range)

Anti germ Fluoro-Polymer Coated Single Piece W.C. Pan Size 395x710x730 mm with solid poly propelyne made soft closing seat cover.(Premium Range)

Anti germ Fluoro-Polymer Coated Single Piece W.C. Pan Size 385 x 720 x 710mm with solid poly propelyne made soft closing seat cover.(Premium Range)

Anti germ Fluoro-Polymer Coated Single Piece W.C. Pan Size 360 x 640 x 685 mm with solid poly propelyne made soft closing seat cover.(Premium Range)

Anti germ Fluoro-Polymer Coated extended wall hung type couple closet Size 760X360X635mm with solid poly propelyne made soft closing seat cover (Premium Range)

Providing and fixing white vitreous china made Anti germ fluoro-polymer coated extended wall hung type couple closet Size 380x650x730 mm along with dual flushing cistern flushing capacity 3 & 6 litre. (Premium Range)

White Vetrious China Anti germ Fluoro-Polymer Coated Wash Basin Size 595x435x185 mm with basin mounted pressmatic pillar cock auto closing system (decol technology). (Premium Range)

White Vetrious China Anti germ Fluoro-Polymer Coated Wash Basin Size 570x820x195 mm with wall mounted pressmatic pillar cock auto closing system (decol technology). (Premium Range)

Providing and fixing white vitreous china type Anti germ fluoro-polymer coated counter top wash basin Size 570x820x195 mm with 15 mm C. P. wall mounted pressmatic Pillar cock auto closing system (decol technology). (Premium Range)

White Vetrious China Anti germ Fluoro-Polymer Coated Wash Basin Size 615x415x150mm with wall mounted single lever concealed basin mixture (cartridge size 32mm.) (Premium Range)

Providing and fixing white vitreous china type Anti germ fluoro-polymer coated counter top wash basin Size 600x400x185 mm with 15 mm C. P. wall mounted single lever concealed basin mixture. (Premium Range)

Providing and fixing white vitreous china type Anti germ Fluoro-Polymer Coated Wash Basin with 15 mm Table mounted single lever Tall boy basin mixture, (cartridge size 32 mm) 15mm quarter turn angular stop cock, 32 mm C. P. brass made waste coupling length 130mm and 32 mm C.P. Brass Made Bottle Trap size 200x300mm fittings and fixtures complete including Painting of fittings and cutting and making good the wall and floors wherever required.

White Vetrious China Anti germ Fluoro-Polymer Coated Wash Basin Size 595x435x185 mm with Table mounted single lever Tall boy basin mixture, (cartridge size 32mm.) (Premium Range)

White vitreous china type Anti germ fluoro- polymer coated counter top wash basin Size 530x420x140 mm with tall boy basin mixture, (cartridge size 32 mm). (Premium Range)

White Vitreous China Anti germ Fluoro-Polymer Coated Urinal Size 340x325x650 mm. (Premium Range)

White Vitreous China Anti germ Fluoro-Polymer Coated Urinal Size 475x315x715 mm. (Premium Range)

White Vitreous China Anti germ Fluoro-Polymer Coated Urinal Size 385x325x635 mm. (Premium Range)

White Vetrious China Anti germ Fluoro-Polymer Coated Urinal Size 340x325x650 mm with sensotronic concealed type flushing valve for urinal complete set with installation box with control cock. (Premium Range)

White Vetrious China Anti germ Fluoro-Polymer Coated Urinal size 385x325x635 mm with concealed sensotronic flushing valve for urinal complete set with installation box, (Premium Range)

White Vetrious China Anti germ Fluoro-Polymer Coated Urinal Size 480x300x740 mm with 15mm Brass made pressmatic auto closing concealed urinal flush valve with wall flange (Decol technology, 400000 operation warranted). (Premium Range)

White Vetrious China made Flat Back Anti germ Fluoro-Polymer Coated Urinal (Inbuilt spreaders, Inbuilt Bottle trap and inbuilt ceramic Waste coupling) Size 340x325x650 mm with sensor (Premium Range)

Providing and fixing white vitreous china flat back Anti germ fluoro-polymer coated Urinal size 7475x315x715 mm (Inbuilt spreaders, bottle trap and ceramic waste coupling) with inbuilt sensor for flushing. (Premium Range)

Providing and fixing in position best Indian ( bonut size 24mm, ceramic disc size 19mm and min. body thickness 2mm, nickel plating. 10 micron and chrome plating 0.3 micron, quarter turn) Angular stop cock. (Premium Range)

Providing and fixing in position best Indian C. P. brass made Shower Arm Length 450mm (nickel plating 0.10 micron and chrome plating 0.3 micron).(Premium Range Sanitary Ware)

Providing and fixing in position best Indian Auto Closing Urinal valve open type with built in control cock wihh wall flange (with DECOL cartridge) for urinal use only. (Premium Range)

Providing and fixing in position best Indian C. P. Brass made (0.3 micron Chrome and 10 micron Nickel plated) Single Towel Rail 600 mm long. (Premium Range)

Providing and fixing in position best Indian C. P. Brass made (0.3 micron Chrome and 10 micron Nickel plated) Towel Rake 600 mm. (Premium Range)

white Vetrious china Anti germ fluoro-polymer coated wall mounted wash basin size 620x480x185 mm. (Premium Range)

white Vetrious china Anti germ fluoro-polymer coated wall mounted wash basin size 570x470x190 mm. (Premium Range)

white Vetrious china Anti germ fluoro-polymer coated wall hung intergrated wash basin size 495x400x365 mm. (Premium Range)

white Vetrious china Anti germ fluoro-polymer coated wall hung intergrated wash basin size 500x440x385 mm. (Premium Range)

white Vetrious china Anti germ fluoro-polymer coated wall hung intergrated wash basin size 635x485x305 mm. (Premium Range)

white Vetrious china Anti germ fluoro-polymer coated wall mounted wash basin size 635x430x190 mm. (Premium Range)

Providing and fixing corner entry 6 mm toughen glass made to measurement shower enclosure size 1200mm x1200mm x 1950mm with aluminum profile on sides, shower enclosure with door sliding on both sides. (Premium Range)

Providing and fixing 8 mm toughen glass wall to wall sliding shower enclosure with one fixed glass and one silding door with a Towel Rod Fixed on the fixed glass size Hight:2000 mm Width: 1500mm to 2000mm. (Premium Range)

Providing and fixing 8 mm toughen glass made to measurement door Openable (inside/outside) shower enclosure two parts Wall to Wall enclosure with one fixed glass and openable door fixed withwall with square hardware & profile glass size Hight: 2000mm Width 800mm to 1200mm. (Premium Range)

Thermostat Mixer : Providing and fixing in position best Indian, concealed high flow bath and shower mixer with thermostatic control cartridge (standard temperature range 15 degree c to 60 degree c, cartridge made of high performance thermostatic Polymer material with Anti scaled function). (Premium Range)

Providing and fixing in position best Indian, satin finish, C. P. Brass grab bar with left/right 90 degree angle, made of 304 grade ss i/c all nuts and screws. (0.3 micron chrome and 10 micron nickel plated). (Premium Range)

Providing and fixing of prestressed vertically casted concrete panels (both surfaces should be smooth and having grooves on both faces) of M-40 grade of concrete of size 2100x300x50 mm having minimum 4 nos of high tensile steel wire as per IS 6006:2014 of dia 3 mm placed horizontally in full length of panel with prestressed precast concrete column of M-40 grade of size 3000x150x150 mm having minimum 7 nos of high tensile steel wire as per IS 6006:2014 of dia 3 mm placed vertically in full length to erect precast boundary wall panels to height 2100 mm from GL including excavation of pit of size 750x750x900 mm in all kind of soil except rock for erection of columns and grouting the pit with M-20 grade of concrete. Manufacturing, transportation and installation at site all complete as per the direction of Engineer-in-Charge.

1 Hectare to 2 Hectare

Add extra for each additional one Hectare or part there off

Excavation of trial pit of size 1.20 m X 1.20 m with minimum depth of 0.9 m and maximum depth of 3.5m as directed by the Engineer in Charge. Trial pit shall be taken at suitable location/ locations as directed by Engineer in charge and shall be indicated on the site plan showing details of soil strata.