ADDN / ALTERATION INCLUDING REPAIRS TO OFFICERS MARRIED ACCN AT ARJUN ENCLAVE AT HISAR MIL STN UNDER GE HISAR

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm thickness below or above ground level complete all as specified and directed.

M&L 50mm thick PCC 1:3:6 type C-2, (using 40mm graded stone aggregate), as in plinth protection finished even and smooth w/o using extra cement complete all as specified and directed.

Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:4) on fair face of brick walls / concrete surfaces external surfaces of any description mixed with WPC @ 200ml per 50 Kg bag of cement used and finished even and smooth w/o using extra cement complete all as specified and directed. Note : WPC will be measured and paid separately.

M&L Rough cast plaster (Rendering coat not less than 15mm thick in CM 1:4, while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg size 6 to 12mm mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even) complete all as specified and directed.

M&L 5mm thick rendering in CM (1:3) on concrete surfaces of ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:6) on internal face of brick walls/ concrete surfaces and finished even and fair complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and as directed.

M&L two coats of Oil bound distemper on new plastered or unplastered surfaces over and including 2mm thick acrylic wall care (Birla / JK white / Asian / Berger) putty and a coat of alkali resistant primer on walls including preparation of surfaces complete all as specified and directed. Note : The work under this item shall be got carried out by contractor from authorised applicator of manufactrurer by using modern technique.

M&L for complete removal of existing treatment, washing down and stopping of distempered and painted surfaces by using electrical operated grinder and applying two coats of oil bound distemper over 2mm thick acryllic wall care putty as approved by GE complete all as specified and directed. Note : The work under this item shall be got carried out by contractor from authorised applicator of manufactrurer by using modern technique.

M&L Preparation of new plastered or unplastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L Preparation of new plastered or unplastered surfaces of wall and applying two coats of white or tinted cement based paint complete all as specified and directed.

M&L for complete removal of existing treatment by using electrical operated grinder from old surface of wall including scrapping and preparation of old plastered surfaces and applying two coats of cement based paint complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of ceiling / soffit and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old steel surface of any description not otherwise described exc 10cm width or girth and applying a coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old wooden surface of any description not otherwise described, exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.

Demolition of cement concrete (unreinforcement) of any description and position complete all as specified and directed.

Treatment of sunken floor slab compraises of the following specifications and all as specified :- (i) M&L for cleaning the sunken/lowered portion of RCC slab surface (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely. 40mm thick avg PCC 1:2:4 type B-0 using 12.5mm graded aggregate as in padding conc to achieve proper slope including cutting holes in bricks or RCC wall for spout. (ii) Rendering of uneven surfaces with 6mm thick CM 1:4 mixed with integral water proofing compound @ 3% by wt of cement consumed. (iii) All junctions points of side wall where CI/GI pipes are passing through shall be sealed with epoxy puty. (iv) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean. (v) M&L for applying two coats of polymer modified cementious water proof coating as per manufacturs instruction to bottom and vertical sides up to finished floor level+100mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion all as specified and directed. (vi) GI pipe 50mm dia medium grade 50cm long laid on each sunken floor as spout complete all as specified and direced by EIC. (vii) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with integral water proofing compound 3% by wt of cement consumed as per manufacturer's specification including rounding of corners and junctions sloping towards spout. (viii) All pipes laid in sunken portion shall be covered with 50mm thick PCC 1:3:6 all round after painting with anticorrosive paint. Note :- (i) Test the water proofed area (ponding test) by filling water for at least 72 hours and tested for leakage seepage and to the entire satisfaction of GE. The treatment shall be carried out by authorised applicators of chemicals. Cost of testing is included in the rates quoted above. (ii) All debries obtained from site will be thrown away out side MD land by contractor at his own expense. (iii) The cost of integral water proofing compound deemed to be inclusive in quoted rate.

M&L for PCC 1:7:12 as in mass concrete using 40mm graded stone aggregate as in filling of sunken portion complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoins, arches pillars etc complete all as specified and directed.

M&L brick work with FLY ASH bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed.

M&L brick work with sub class 'B' bricks old size straight or curved on plan exc 6mtr mean radius, built in CM (1:4) complete all as specified and directed.

M&L brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landing etc not exc 200 mm thick (horizantal or slopping) for fair finished surfaces of concrete complete all as specified and directed.

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floor, roof landings, balconies, canopies and in shelves copmplete all as specified and directed.

M&L for RCC M-25 (design mix) using 20mm graded stone aggregate in chajja complete all as specified and directed.

Dismantling brick tiles or terracing tiles, single layer on roofs complete all as specified and directed.

Demolition mud in roofs, any thickness, including plastering and leeping(whether full thickness removed or only a part thereof) complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate leveling course average thickness 25mm on roof slab complete all as specified and directed.

M&L for 10mm thick rendering in cement mortar (1:3) on fair face of roof concrete surfaces of any description mixed with WPC @ 200ml per bag of cement and finished even and smooth w/o using extra cement complete all as specified and directed. Note : WPC will be measured and paid separately.

M&L cleaning plastered roof surface and applying a coat of bitumen primer @ 0.30kg per Sqm and 3mm thick APP based membrane weight not less than 3.5kg / Sqm with polyster non woven fabric (weighting not less than 150gm / Sqm laid on primed surface by torch application, side overlaps shall be 75mm and ends shall be 100mm and all overlaps and joints shall be sealed by torch application complete all as specified and directed.

M&L 18-20mm thick Kota stone slabs over and including 15mm thick screed layer in CM (1:4), laid and jointed with grey cement slurry mixed with pigment to match the shade of stone incl rubbing & polishing complete all as specified and directed. Note :- (i) The size of kota stone in flooring shall be 550 x 550mm (minimum). (ii) Kota stone on treads of stair case shall be in one piece.

M&L 18-20mm thick Kota stone slabs as in vertical surfaces like dado or skirting over 10mm thick rendering in CM (1:4) set & joined in neat cement slurry and pointed in coloured cement to match incl rubbing & polishing complete all as specified and directed. Note :- Kota stone on risers of stair case shall be in one piece.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and removal complete all as specified and as directed.

M&L for non-skid ceramic coloured tiles 7 to 8mm thick (Square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick cement screed bed CM (1:4) complete all as specified and directed.

M&L vitrified ceramic tiles light shade 10mm thick (square/ rectangular) polished area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick cement screed bed in CM (1:4) complete all as specified and directed.

M&L vitrified ceramic tiles light shade 10mm thick (square/ rectangular) polished area of each tile not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick cement screed bed in CM (1:3) complete all as specified and directed.

M&L for coloured designer glazed ceramic tiles of size 300 x 450 x 7mm thick as in vertical surface like dado or skirting set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick rendering in cement mortar (1:3) complete all as specified and directed.

M&L for 20 mm thick granite stone slab topping table rubbed and polished (one piece) in cooking platforms laid over 15mm thick cement screed bed or bedding layer in CM (1:4) including pointing in white cement (1:2) using marble dust complete all as specified and directed.

M&L 25mm thick Baroda green (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like including 20mm screed bedding in cement mortar (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of stone complete all as specified and directed.

S&F in repair vitreous china squatting pan (1st quality) ISI marked Orrisa pattern size 580mm x 440mm white with integral foot rest with CI ‘P’ or ‘S’ trap and fixing in lime concrete (1 lime, 2 sand and 5 aggregate), 150mm thick alround and finished just below level of rim of pan to receive the floor finishing complete all as specified and directed.

S&F in repair viterous China wash down water closet (pedestal pattern) complete connecting to flush pipe, including plastic seat cover with flat bottom and mild steel chromium plated or aluminium hinging device (excluding flushing cistern and flushing pipe) complete all as specified and directed. Make : Jaquar ESSCO WC cat part No ECS-551SSPP & Seat cover cat part No ECS-551PNPP or equivalent in Parryware / Hindware.

S&F in repair, PVC low level cistern 10 lit capacity, valveless, syphonic action type with float, handle incl 32mm dia flush pipe of polyethylene of low or high density or PVC & bracket etc complete all as specified and directed. Make : Jaquar ESSCO Cat part No WHE-WHT-183NL or equivalent make as specified in Appx 'B'

S&F in repair vitreous china wash basin, white, flat back, size 555 x 410 x 255mm with and including 32mm bore waste fitting of brass chromium plated, PVC connection and PVC waste pipe and fixing with new brackets including cutting and pinning in ends of brackets complete all as specified and directed. Make : Jaquar ESSCO cat part No ECS-WHT-801 or equivalent in Parryware / Hindware.

S&F in repair stainless steel kitchen plate rack of overall size 24" x 36" x 10" made out of 0.63mm thick stainless steel sheet, fixed with suitable size of screws of first quality complete all as specified and directed. Make : Cat part No SSKPR-312 of Bluestar Sanitary Industries Pvt Ltd (Silver Shine) or P-336 of Prayag or equivalent make as specified in Appx 'B'.

S&F in repair 15mm bore chromium plated cast copper alloy bib taps with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make : Jaquar ESSCO Cat part No DLX-511KN or equivalent makes in MARC/ Plumber.

S&F in repair 15mm bore stop valves/angle valve fancy type chromium plated cast copper alloy with crutch or butterfly handles screwed down high pressure screwed both ends for iron pipe or brass ferrule complete all as specified and directed. Make : Jaquar ESSCO Cat part No MQT-513AKN (Stop Valve) or MQT-526KN (Angle valve) or equivalent makes in MARC/ Plumber.

S&F in repair over head shower rose complete all as specified and directed. Make : Jaquar ESSCO Cat part No EOS-541RB or equivalent makes in MARC/ Plumber.

S&F in repair stainless steel tubular towel rail 20mm dia 60 long between flanges complete all as specified and directed. Make : Jaquar ESSCO Cat part No AEC-1111N or equivalent make as specified in Appx 'B'.

S&F PVC connection 15mm size, of length 450mm, with brass nuts complete all as specified and directed.

S&F in repair toilet paper holder complete all as specified and directed. Make : Jaquar ESSCO Cat part No ACN1151N or equivalent makes in Grohe/ Kohler.

S&F in repair Brass CP wall mixer with provision for overhead shower with 115mm long bend pipe on upper side, connecting legs & wall flange complete all as specified and directed. Make : Jaquar ESSCO Cat part No MQT-517BKN (Wall mixer) or equivalent makes in MARC/ Hindware

S&F in repair chromium plated fancy type pillar taps cast copper alloy with capstan head screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed. Make : Jaquar ESSCO Cat part No DLX-507KN or equivalent makes in MARC/ Kohler.

Taking up or down steel water tubing and connection of 15mm bore complete all as specified and directed.

Taking up or down steel water tubing and connection of 20mm bore complete all as specified and directed.

S&F for GI tubing 15mm bore ISI marked with all fittings and fixed complete to walls, ceilings or laid in floors medium grade complete all as specified and directed.

S&F for GI tubing 20mm bore ISI marked with all fittings and fixed complete to walls, ceilings or laid in floors medium grade complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. (Note :- +10mm tolerance in size /dimension of sink is permissible as per standard manufacturers catalogues of makes mentioned in Appendix 'B')

S&F in repair stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions chromium plated (long shank concealed type) and fixed to pipe of 20mm bore complete all as specified and directed.

Dismantling RCC/PCC water tanks of any description of capacity exc 250 Liters but n.exc 500 Liters complete all as specified & directed.

Dismantling RCC/PCC water tanks of any description of capacity exc 500 Liters but n.exc 1000 Liters complete all as specified & directed.

S&F PVC water tank triple layer white in colour rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted & fixed in position of capacity 1000 ltr complete all as specified and directed.

S&F PVC water tank triple layer white in colour rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted & fixed in position of capacity 500 ltr complete all as specified and directed.

S&F ball valve 20mm bore high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed, (minimum weight 210 gms) complete all as specified and directed.

S&F in repair CP soap dish fixed with screw complete all as specified and directed. Make : Jaquar ESSCO Cat part No AEC-1131N or equivalent makes in MARC/ Kohler.

S&F in repair decorative corner glass shelf fixed with chromium plated brass screw on plug or gutties fixed in wall complete all as specified and directed. Make : Jaquar ESSCO Cat part No ACN-1173 or equivalent makes in MARC/ Kohler.

S&F in repair hand shower (Health faucet), 8mm dia, 1 meter long flexible tube and wall hook with hose & hook complete all as specified and directed. Make : Jaquar ESSCO Cat part No ALE-ESS-583 or equivalent makes in MARC/ Plumber.

S&F in repair two way 15mm bore Long spout bib cock wall flange fixed to pipe complete all as specified and directed. Make : Jaquar ESSCO Cat part No DLX-512AKN or equivalent makes in MARC/ Plumber.

Dismantling cast iron work of any description complete all as specified and directed.

S&F for cast iron 75mm bore sand cast soil waste and vent pipe in any length with or w/o ears with cement joints laid in trenches or in floors complete all as specified and directed.

S&F for cast iron 75mm bore sand cast soil waste and vent pipe in any length with or w/o ears with cement joints fixed to wall complete all as specified and directed.

S&F 75mm CI Bends (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and as directed.

S&F 75mm CI Bends (any radius) with duck’s foot or heel rest complete all as specified and as directed.

S&F 75mm CI Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S&F for cast iron 100mm bore sand cast soil waste and vent pipe in any length with or w/o ears with cement joints laid in trenches or in floors complete all as specified and directed.

S&F for cast iron 100mm bore sand cast soil waste and vent pipe in any length with or w/o ears with cement joints fixed to wall complete all as specified and directed.

S&F 100mm CI Bends (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and as directed.

S&F 100mm CI Bends (any radius) with duck’s foot or heel rest complete all as specified and as directed.

S&F 100mm CI Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

M&L cast iron floor trap, with grating inlcuding jointing to waste pipe diameter of outlet on 75mm fixed in PCC (1:2:4) type B-1 complete all as specified and directed.

Taking down eaves gutter or RWP of any description complete all as specified & directed.

S&F 110mm dia PVC rain water pipe single socketed with rubber joint, jointed with solvent cement fixed to wall complete all as specified & directed.

S&F PVC bends any radius 110 mm dia complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n exc. 1.50 sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc. 1.50 sqm & n.exc 4.00 sqm each complete all as specified and directed.

S&F Pressed steel frames for doors with one or more rebates including necessary lugs, hinges, lock strike plate, size of frame 125 x 60mm complete all as specified and directed.

S&F Pressed steel frames for doors with one or more rebates including necessary lugs, hinges, lock strike plate, size of frame 105 x 60mm complete all as specified and directed.

M&L cement concrete (1:3:6) type C-0 (using 12.5mm graded stone aggregate) in filling of pressed steel frame and hold fast block etc including necessary form work complete all as specified and directed.

S&F 35mm thick flush shutter, soild core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed.

S&F 35mm thick factory made IInd class hard wood panelled door shutters (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered partical board with commercial veneering on both face. The size of rail & stile as per IS :1003 (Part-I) kilnseasoned and chemically pressure treated complete all as specified and directed.

S&F 35 mm thick factory made glazed and skeleton shutters of 2nd class HW open rebated and prepared to receive glass/gauze (without sash bar) etc edges or framing plain chamfered or rounded fitted with cut or mitred beads for securing glass etc as specified in SSR pt-1 section 8.24 (a) complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F factory made wood grain printed (Prelaminated) solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes 19 mm x 19 mm having wall thickness 19 gauge for stiles. MS tube 15mmx 15mm having wall thickness 19 gauge for top and bottom rails. MS frame shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded prelaminated colour PVC 'C' channel having 5mm thick PVC sheet strip 20mm wide struck inside with solvent cement for stiles and 5mm thick PVC sheet for top rail, lock rail and bottom rail on either side and 10mm (5mm x 2) thick, 20mm wide cross PVC sheet as gap insert for top and bottom rail. Paneling of 5mm thick prelaminated colour PVC sheet to be fixed in MS frame welded/sealed to the stiles and rails with 5mm x 30 mm PVC sheet beading on either side and jointed together with solvent cement adhesive and an additional 5mm thick PVC strip of 20mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete all as shown in SSR part II 2010 each door shutter consist of 4 Nos 100mm long MS butt hinges complete all as specified and directed.

S&F factory made wood grain printed (prelaminated) Solid PVC door frame of size 50mm x 47mm made out of 5mm prelaminated colour PVC sheet reinforced with MS square tubes of 19 x 19mm having wall thickness 19 gauge, fixed in opening as per specification & drawing given in SSR Part-II 2010 including making good disturbed surfaces to match with existing complete all as specified and directed.

S&F butt hinges 100mm medium weight cold rolled mild steel including necessary welding if required complete all as specified and directed.

S&F in repair, prelaminated PVC solid board of plastiwood or PVC Plywood, 18/19mm thick, prelaminated on one side with decorative choice lamination & other side balancing white lamination including pasting with solvent chemical as required in kitchen cabinet / shelves etc, at site or fixed with screws including necessary brass handle, locking arrangement, sliding channel complete all as specified & directed.

S&F in repair factory made solid PVC moulded door shutter / kitchen cup board / drawer with particle board core 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel designed with 2mm thick moulded pre-laminated PVC sheet on the front face & 2mm plain colour PVC sheet on back face all as per drawing in SSR Part - II 2010 and fixed to frame each shutter consisting aluminium butt hinges 100mm size - 03 Nos, Aluminium tower bolts 150mm - 02 Nos, Aluminium handles 125mm - 02 Nos complete all as specified and directed.

S&F in repair 19-20 mm thick block boards, grade 2 quality, interior grade, decorative type with decorative face veneer on one face and other side balancing white fixed with screws to timber as in pelmet / shelves frame work complete all as specified and directed.

S&F 2nd class hard wood plain solid, straight chowkhat as in cup board complete all as specified and directed.

S&F 25mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F continous piano hinges mild steel bright finish or electro galvanised of 30mm width of flaps complete all as specified and directed.

S&F 100mm aluminium anodised Hasp and staple, safety type complete all as specified and directed.

S&F for 150mm long Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 200mm long Aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

M&L for two coats of synthetic enamel paint to new wood or wood based surfaces of any description not otherwise described over 10 cm in width or girth including preparation of surfaces over a coat of pink primer complete all as specified and directed.

S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S&F factory made steel window / ventilator, ISI Marked, (Box type) with side hung shutter including projecting type hinges with steel handle and tower bolt and steel peg stay with glazing bar, dovetailed or welded including with shop coat of zinc primer and making good disturbed surfaces of walls complete all as specified and directed. Note : HQ CEJZ Drawing No TD/2013/01 Sheet 1/3,2/3,3/3.

S&F factory made steel window / ventilator, ISI Marked, (Box type) with side hung shutter including projecting type hinges with steel handle and tower bolt and steel peg stay without glazing bar, dovetailed or welded including with shop coat of zinc primer and making good disturbed surfaces of walls complete all as specified and directed. Note : HQ CEJZ Drawing No TD/2013/01 Sheet 1/3,2/3,3/3.

S&F factory made Mild steel ventilator with top hung shutter incl hinges, steel peg stay with shop coat of primer zinc chrome complete all as specified and directed.

S&F powder coated aluminium frame & shutter for doors, windows, ventilators, partitions & grills etc of any colour as approved (thickness of powder coating shall be not less than 50 micron) including necessary joining cleat glazing clips, rubber neoprene packing aluminium snap beading, screws etc complete all as specified and directed. Note : Hinges, tower bolts, handles, glass panes, wire cloth shall be measured and paid separately under respective item of BOQ

M&L mild steel round / square bars as in window guard bars including necessary welding, confirming to Fe-290 gde E-165 complete all as specified and directed.

M&L for preparation of new steel surface of any description not otherwise described exc 10cm width or girth and applying two coats of synthetic enamels paints over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of new steel surface of any description not otherwise described exc 10cm width or girth and applying two coats of synthetic enamels paints over existing treated shop coat primer complete all as specified and directed.

M&L 3mm thick plain sheet glass, ordinary quality n.exc 0.5 Sqm in each pane complete all as specified and directed.

M&L 5mm thick plain sheet glass, ordinary quality n.exc 0.5 Sqm in each pane complete all as specified and directed.

M&L TMT bars 10mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L TMT bars 6 to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Chipping of unsound weak concrete / cover of reinforcement over slab, column, beam and wall or as per site requirement by chieseling maximum up to 50mm depth and disposal of malwa from site complete all as specified and directed.

Supply and apply of rust remover cum passivator to remove rust from existing reinforcement product : dust proof (FOSROC / SIKA / THERMAX / HILTI) of density 1.01 kg/l at 30°C and consumption 0.20 kg/ sqm complete all as specified and directed.

Supply and apply of two coats of cement based polymer modified rebar corrosion protection system to existing reinforcement. Product: cement based polymer modified rebar corrosion protection system (FOSROC / SIKA / THERMAX / HILTI) Consumption: 3.75 kg/m2 for two coats. Product requirements: carbonation resistance: 2 mm of SikaTop Armatec ®-108 corresponds to 20 mm of normal mortar; bond strength > 1N/mm2 according to ASTM C 882-78.

Providing & fixing rebar of required length (160mm) & diameter (16 mm) with Sika AnchorFix®-3+ / Mungo / Fischer FISV 390 / Hilti RE-500 Epoxy resin whereever required in RCC members including power drilling, cleaning of holes, then rebars should be inserted in holes that should be filled with epoxy to ensure the bond as per manufacturer's recommendation complete as per site requirement and directions of Engineer-incharge.

Providing & fixing rebar of required length (200mm) & diameter (20 mm) with Sika AnchorFix®-3+ / Mungo / Fischer FISV 390 / Hilti RE-500 Epoxy resin whereever required in RCC members including power drilling, cleaning of holes, then rebars should be inserted in holes that should be filled with epoxy to ensure the bond as per manufacture recommendation complete as per site requirement and directions of Engineer-incharge.

Providing & fixing shear connectors of 16 mm dia TOR steel up to 160mm length with Sika AnchorFix®-3+ / Mungo / Fischer FISV 390 / Hilti RE-500 Epoxy resin RCC members including power drilling, cleaning of holes, insertion of epoxy, placing shear connectors in position to ensure the bond as per manufacture recommendation complete as per site requirement and directions of Engineer-incharge.

Providing, mixing & applying two component Epoxy resin concrete Bonding coat on prepared RCC surfaces as per manufacture specification including prepartaion of surface by chipping and throughly cleaning of surface complete whereever required and as per directions of Engineer-in-charge. Product: Sikadur®-32 LP./ MasterBrace1441/Fosroc Consumption: 0.4 kg/m2. Product requirements: Complies with ASTM C 881 Type II Grade 2 Class B+C.

Providing and fixing water tight centering and shuttering including bolting, strutting, propping etc. including removal of form work from column, beam etc. complete as per site requirement and directions of Engineer-in-charge.

Supply and apply a ready to use non shrink, cementitious free flow micro-concrete (> 100 mm). Product: SikaRep® Microcrete-4 + adequate coarse aggregate./ Master Emaco® 466 Yield: approx. 17 ltr/bag (30kg) (depending on the size and quantity of coarse aggregate added) Product requirements: compressive strength > 60 N/mm2 (28 days) according to ASTM C 1107-99.

Making 'V' groove of 3mm wide and 3mm deep over crack line by electrically operated angle grinder with diamond concrete saw blade and cleaning it by air blower as directed and filling up of crack with crack filling material by Engineer-in-charge.

Supply and apply of rust non shrink repair mortar for non-moving cracks in plaster and walls. Product : Sika Cracksil/ MasterBrace2200/ Fosroc Consumption : 25 RMT/ kg for crack size of 6mm x 6mm. Density: 0.85 Kg/l at 27° (degree centigrade)

Supply and apply a epoxy resin based solvent free bond coat. Product: FOSROC / SIKA / THERMAX / HILTI Consumption: 0.4 kg/m2. Product requirements: Complies with ASTM C 881 Type II Grade 2 Class B+C.

Supply and apply a pre-batched one component polymer modified cementitious patch repair mortar for a thickness of 40mm or as directed by Engineer-in-charge. Product : FOSROC / SIKA / THERMAX / HILTI Yield: approx. 0.84 ltr/kg. System requirements : compressive strength ≥ 50 N/mm2 (28 days) according to ASTM C 109; flexural strength ≥ 3N/ mm2 (7 days) according to ASTM C 293-79.

Drilling and fixing injection packers in RCC, including : Drilling Holes: Drilling holes 10mm diameter in masonary structure at the intervals as per recommendation of engineer in charge. Cleaning of holes: Clean the holes by air blower prior to fixing nozzles. Fixing of Packers: Sika® Packer, 9.8mm diameter, 10cm long, with high strength steel screw and structured rubber sealing, in cleaned holes. If required use Sikadur 31 to fix packers securely. Cutting of Packers: Cut the packers by cut of wheel after completion of grouting without damaging structural elements.

Supply and apply of a 3 part, very low viscous, elastic polyacrylic injection resin with a versatile and adjustable reaction time having the following properties:Mixed viscosity : 3-11 M.pa.s at +20 Deg C, Reaction time : adjustable according to ambient temperatrure and execution requirement between 8-50 mins, pH – 9-10, Tested as per Wissbau No. 2002-094-(1A) – Function test with re-injectible hose system.Product: Sika® Injection 306. Note for Srl item No 120 to 136 : (i) Necessary scaffolding / props (minimum one prop per sqm) required for repair works against aforesaid items is deemed to be included in contractor's quoted rate. (ii) Work has to be carried upto two storey buildings and nothing extra shall be paid to contractor on this ground. (iii) Digital photo / videography for all items of structural strengthening shall be done by the contractor in presence of JE (Civ) / Engineer-in-Charge. Copy of CD thereof shall be deposited to Engineer-in-Charge for record on completion of each stage as elaborated here-in-above. (iv) Cement used for the structural repair / rehabilitation work shall be of OPC grade.

Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles as necessary gusset plate, riveting etc conforming to Fe-290 Gde E-165

S&F in repair 25mm bore & 1.00mm wall thicness stainless steel fancy type decorative curtain rod with 02 Nos decorative side stoppers (for each opening) fixed on wall with wooden gutties & screws complete all as specified and directed.

S&F in repair stainless steel decorative type powder coated brackets suitable for 20mm dia curtain rod or similar articles complete all as specified and directed. Make : Jindal or Hindalco or Deco

Excavation in trenches in soft / loose soil not exceeding 1.5m wide and not exceeding 1.5 m in depth for laying of cable and getting out complete all as specified and directed.

Demolition and breaking up 150mm bore drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick in soil complete all as specified and directed.

Removing excavated soil / material to a distance not.exc. 50m and depositing where directed at a level not exc. 1.5m above starting point complete all as specified and directed.

M&L Cement concrete Type D-2 1:4:8 (40 mm graded stone aggregate) in foundations, filling and mass-concrete complete all as specified and directed.

M&L Cement concrete Type B1 1:2:4 (20 mm graded aggregate) as in bed plates, kerbs, water troughs and the like including weathering, slightly rounded for chamfered angles and throating complete all as specified and directed.

M&L 150 mm bore Reinforced concrete pipes, class NP 2 with one collar per length of pipe complete all as specified and directed.

Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; inCement concrete 1:3:6 type C-2 complete all as specified and directed.

S&F Steel fibre reinforced concrete (SFRC) cover and frame (Heavy duty HD-20 grade designation) 560 mm internal diameter confirming to IS-12592, total weight of cover and frame shall not be less than 182 Kg and to be fixed in cement concrete 1:2:4 type B-1 complete all as specified and directed.

M&L 50mm thick PCC 1:4:8 type D-2 as in sub base finished even and fair complete all as specified and directed.

M&L, Coloured machine pressed precast (rubber moulded vibratory) concrete interlocking paver block (With grey cement and pigment) any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, laid over and including 25mm thick sand cushioning complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Erection & refixing only (as in steel gate) framed work in position after carrying out necessary repairs to steel gate complete inlcuding providing new MS sections and made the steel gate fully functional to the entire satisfaction of Engr-in-Chage complete all as specified and directed. Notes : (i) Additional new MS work shall be measured and paid under srl item No 137. (ii) The steel gate shall be made fully functional after fixing in position. Cost of minor like grease, oil etc shall deemed to include in quoted rate.

S&F, Steel rolling shutters of 1mm thick lath , without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; errected in position as indicated, complete; push pull or manual type complete all as specified and directed.

M&L for cement concrete tiles 25cm x 25cm x 22mm thick with grey cement and no pigments machine pressed, set, jointed and pointed in neat cement slurry over roof surface over 15mm thick cement screed in cement mortar (1:4) complete all as specified and directed.

Taking down carefully surface aluminium point wiring with wooden battens / PVC conduit (light, fan, socket, bell or power) including fittings such as switches, ceiling roses, lamp holders, pendants, sockets, regulators etc and making good disturbed surfaces complete all as specified and directed.

Taking down old unserviceable / burnt submain wiring of any size including earth wire and making good of the disturbed surface and removing the material from site complete all as specified and directed.

M&L for point wiring alongwith earth continuity conductor with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories, for mounting modular switches, sockets, fan regulators, including cutting, chasing on wall and other surfaces and making goood disturbed surface complete for the following :- Note : Modular boxes, modular face plate and modular plate cover shall be measured separately in respective item of BOQ.

One light / fan / bell point controlled by one switch

One socket outlet 6 amp controlled by one switch on the independent board.

One socket outlet 6 amp controlled by one switch on the same board.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 2.5 sqmm drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories, with earth continuty conductor with FRLS PVC insulated multistranded copper conductor cable 2.5 Sqmm complete for one 16 Amp modular socket outlet controlled by one switch on independent board, including cutting, chasing on wall and other surfaces and making the good disturbed surface complete. Note : Modular boxes, modular face plate and modular plate cover shall be measured separately in respective item of BOQ.

M&L for point wiring with 1100 volts grade PVC insulated unsheathed FRLS multistranded copper conductor cable 4 sqmm drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories, with earth continuty conductor with unsheathed FRLS PVC insulated multistranded copper conductor cable 4 Sqmm complete for one 16 Amp modular socket outlet controlled by one switch on independent board, including cutting, chasing on wall and other surfaces and making the good disturbed surface complete.

S&F socket outlet modular type shutterd and interlocking flush type 230/250 volts grade for :-

Socket outlet 2 in 1, 5 Pins, 6 Amp two module

Socket outlet 2 in 1, 3/5 Pins, 6/16 Amps combined two module

S&F modular Switch 6 amp single Pole one way, one module 230 V complete all as specified & directed.

S&F modular Switch 16 amp single Pole one way, one module 230 V complete all as specified & directed.

S&F modular bell push Switch 6 amp with indicator single Pole one way, one module 230 V complete all as specified & directed.

S&F multi music type bell AC 240 volts, single pole complete all as specified and directed.

S&F fancy lamp holder insulated body with back plate suitable for batten fitting and connecting up complete all as specified and directed.

S&F LED retrofit lamp B-22 holder base with polycarbonate diffuser and aluminium heat sink 15 Watt complete all as specified and directed. Make : Cat Part No LTHPLEDLAMP15W/B22 of C&S or equivalent make as specified in Appx 'B'.

S&F fancy ceiling rose of 65 x 50mm PVC / polycarbonate three terminal surface bakelite complete all as specified and directed.

S&F LED light fitting 18 W for magnum retro (single side connection) LED energy saving high efficiency PMMA difuser given soft glare free light, environment friendly, energy efficient long life, corrosion resistant, impact proof, surface mounting PC housing ready to use pack complete all as specified and directed. Make : Havells Cat part No MAGNUMRETROILS1X18PC or equivalent of make as apecified in Appx 'B'

S&F modular electronic ceiling fan regulator stepped type heavy duty suitable to work on 230 volts complete all as specified and directed.

S&F sheet metal enclosures distribution boards, double door three phase 415 volts 4 ways for MCCB, FP as incoming and MCB(TP/SP) as outgoing,comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed. Note :- (i) The DB shall be VTPN of Indoasian, Cat Part No - NVMCCB04 or equivalent makes of Havells, Legrand, Schneider. (ii) The DB shall be flush fixed ,and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost. (iii) connection of the MCCBs/MCBs with cable shall be made through appropriate size pin /bottle type thimble -properly crimped. (iv) All the vacant holes of the DB shall be provided with blank plates of appropriate size.

S&F MCCB 100 Amp 4 pole Breaking capacity 16 KA, complete all as specified and directed.

M&L for MCB SP 240 volts, 6-32 Amps, 10KA, 'C'-Series complete all as specified and directed.

M&L for MCB SPN 240 volts, 40 Amps, 10KA, 'C'-Series complete all as specified and directed.

S&F factory made sheet metal enclosure MCB DB SPN 8 way with 200 amps rated bus bar 240 volts double door with isolated neutral bar and shrouded bus bar IP protection 43 having door earthing complete all as specified and directed. Make : Indoasian Optipro Cat Part No - 811807 or equivalent makes as specified in Appx 'B'.

S&F sheet metal enclosures with socket plug top and MCBs single pole and neutral enclosures with 2 pin and earth plug and socket complete with one SP MCB of 20 Amp rating 240 Volt complete all as specified and directed.

M&L submain wiring with 2 runs of single core 6 Sqmm PVC insulated unsheathed multisranded 1100 volts grade with FRLS copper conductor drawn through and including ISI marks PVC conduit concealed and conduit accessories of medium grade not less than 25mm dia including one run of single core 6 Sqmm FRLS PVC insulated unsheathed multistanded 1100 volts grade with copper conductor cable as earth conductor along with wiring and connected from DB to DB / main board complete all as specified and directed. Note : Two run of 6 Sqmm cable and one run of 6 Sqmm earth cable and one run of 25mm PVC conduit shall be considered as a unit for measurements purpose.

S&F metalic exhaust fans 300mm AC single phase 230/240V with louver and all connected assessories complete all as specified and directed.

Supply, laying, jointing, testing and commissioning of LT UG XLPE insulated screened PVC beded galvanised steel strip or wire, armoured heavy duty electric power cable with aluminium conductor, 1100 volt grade, cross sectional area of size 35 sqmm 4 core laid in trenches wall / floor etc including taking out existing unserviceable LT cable complete all as specified and as directed. Note : Cable may be laid in trenches, under road, across the nallah, along poles / walls and ducts etc. Excavation, earthwork, sand chshioning, cable cover, pipe for cable protection to be measured and paid saprately.

M&L for Sand filling in trenches with clean dry fine sand unwashed including gently punning around cables complete all as specified & directed. Note : Punned thickness shall be measured.

M&L for brick covering to underground electric cable using fly ash old size brick laid dry flat per pendicular to the direction of cable complete all as specified and directed.

S&F street light fitting LED 18/20 W, pressure die cast aluminium housing & connected with and including 0.5 Sqmm flexible copper multistranded conductor cable including, security light bracket made to shape out of GI pipe 40mm bore light grade, 1.5 mtr length and fixed with MS clamps of size 40 x 5mm - 02 Nos, Nuts, Bolts and washers on wall the light to be fixed on Bldg complete all as specified and directed. Make : Havells Cat Part No ENDURAPEARLSL20WLED757SASYTOPS or equivalent of make as apecified in Appx 'B'

M&L for replacement of 50 mm bore GI pipe light grade laid in trenches or fixed to wall / pole for protection of cable / earthing strip etc complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground not less than 2.25 mtrs deep below normal ground level with top edge of the plate not less than 1.5 mtrs below normal ground level, surrounded from all sides with mixture of charcoal and common salt, connected to galvanized earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel protected by galvanised iron light grade 15 mm dia pipe and 20mm light grade for water filling including 15x20mm reducer socket funnel wire mesh, RCC cover with concrete 1:2:4 using 8 mm# bar@100 mm c/c both ways ,PCC chamber pit with PCC (1:3:6) type C-2 and excavation and earth work,disposal of suplus spoil to a dstance not exceeding 50mtrs all as specified and shown on electrical plate No. 3 of 2009 (Part-I) including taking out old existing earthing complete all as specified and directed. Note :- The unit rate includes for protection pipe and GI wire 4mm dia from top of earth plate up to 7.5 meter above ground level.

M&L Cutting chases, pinning in making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; for concealed water tubing etc and making good, cutting exc 10cm but n.exc 20cm girth complete all as specified and directed. Note : The cutting of chases will be done using wall chaser / wall groove cutting machine only.

S&F water heater storage type BEE 5 star rated electric vertical type complete of capacity 25 ltr complete all as specified and directed.

Supply and fixing hot / cold water PVC connection of 15mm bore heavy duty, length upto 45cm with brass nut joints and washers at both ends complete all as specified and directed.

S&F one star rated energy saving ceiling fan 1200mm sweep as per latest IS-374-2019 having service value ≥ 4 to 4.5 m3/min/w and 50 watt with double ball bearing and three blades with all accessories, down rod, two nos canopy, white in colour including 2 core 0.5 sqmm copper flexible cable for connection from ceiling complete all as specified and directed.

M&L for modular white cover plate with frame, 2 module complete all as specified and directed.

M&L for modular white cover plate with frame, 3 module complete all as specified and directed.

M&L for modular white cover plate with frame, 4 module complete all as specified and directed.

M&L for modular white cover plate with frame, 6 module complete all as specified and directed.

M&L for modular white cover plate with frame, 8 module complete all as specified and directed.

M&L for modular metal flush box, 1/2 module complete all as specified and directed.

M&L for modular metal flush box, 3 module complete all as specified and directed.

M&L for modular metal flush box, 4 module complete all as specified and directed.

M&L for modular metal flush box, 6 module complete all as specified and directed.

M&L for modular metal flush box, 8 module complete all as specified and directed.

LACHHMAN SINGH AND BROTHERS

Siya constructions

M/S RAJINDER SINGH