Provn of 01 x Single Offr Living with toilet facilities at MFFR under AGE (I) MFFR

Amount

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, cable/pipe line trenches etc and getting out in loose/soft soil complete all as specified and as diected.

M&L for PCC (1:4:8) type D2 using 40mm graded stone agg as in mass filling and foundation complete all as specified and as diected.

M&L for Brick work with fly ash bricks old size straight or curved on plan exceeding 6m mean radius built in CM 1:6 complete all as specified and as diected.

M&L for Form work to sides of concrete foundations, footings, bases of columns, sides and soffits of foundation and plinth beams complete all as specified and as diected.

M&L for Form work to sides and soffits of floor or roof beams, lintels, cantilevers etc complete all as specified and as diected.

M&L for Form work to sides of pillars, posts and columns complete all as specified and as diected.

M&L for M-25 design mix using 20mm graded aggreate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as diected.

M&L for M-25 design mix using 20mm graded aggreate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as diected.

M&L for M-25 design mix using 20mm graded aggreate as in Columns, pillars, piers, posts and struts complete all as specified and as diected.

M&L for steel reinforcement TMT bars 10 mm dia and over cut to length and bent to shape required including cranking, bending spirally for hoping for columns,beam, hooking end and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as diected.

M&L for steel reinforcement TMT bars 5mm dia and over upto 10 mm dia bent to shape required including cranking, bending spirally as in stirrups and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as diected.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and as diected.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as diected.

M&L for 15mm thick Rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces, finished fair and even without using extra cement complete all as specified and as diected.

M&L for 10mm thick Rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished fair and even without using extra cement complete all as specified and as diected.

M&L for Preparing new plastered or unplastered surfaces of walls and applying two coats of cement paint white or tinted over a coat of alkali resistant primer complete all as specified and as diected.

M&L for Preparing new plastered or unplastered surfaces of walls and applying two coats of oil Bound Distemper white or tinted over a coat of primer complete all as specified and as diected.

M&L for sand filling under floors or in foundation including watering and consolidations complete all as specified and as diected.

M&L for broken stone Hardcore of broken stone or boulders of gauge n. exc 63 mm, deposited, spread and levelled in layers n. exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as diected.

M&L for 75mm thick PCC 1:4:8 type D-2 using 40mm graded stone agregate as sub base of floors complete all as specified and as diected.

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate in any position in floor/roof complete all as specified and as diected.

M&L for Virified Ceramic tiles dark colour/double charged of size 600x600 mm and 10 mm thick (square) polished, as in floors & skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles over and including 15 mm thick screed in CM 1:6 in floor and 10mm thick rendering in skirting complete all as specified and as diected.

M&L for coloured non-skid tiles of size 400mmx400mm and 7 to 8mm thick (square) as in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15 mm thick screed in CM 1:4 complete all as specified and as diected.

M&L for Glazed ceramic coloured tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick rendering in CM 1:4 complete all as specified and as diected.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and as diected. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as diected. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

M&L for mild steel work as in hold hast etc complete all as specified and as diected.

M&L for Cement concrete 1:3:6 type C-0 using 12.5 mm graded stone aggregate as in filling in pressed steel frame chowkhats etc complete all as specified and as diected.

S&F Second class hard wood, glazed and skelleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc without sash bar, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing gauze etc, size of members as directed supplied and fixed to chowkats complete all as specified and as diected.

M&L for painting to new wooden surface over 10cm width or girth with two coat of synthetic enamel paint over a coat of pink primer including preparation of surfaces complete all as specified and as diected.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm, fixed with tinned tacks or galvanised wire staples complete all as specified and as diected.

S&F factory made solid panel PVC door shutter with MS square tube 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC sheet stirip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top,lock and bottom rail on either side & as gap insert for top rail & bottom rail .panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement as details shown on page 176 of SSR Part-II, complete all as specified and as diected.

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete as shown at detail 'C' on page 180 of SSR Part-II complete all as specified and as diected.

S&F Anodised aluminium frame /truck for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as diected.

S&F Anodised aluminium window and ventilator shutters,/ sliding shutter , fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, wire mesh and grills etc. complete all as specified and as diected.

S&F 4.8mm thick sheet glass, ordinary quality and glazing with oil putty/rubber gasket in square of any thickness in each pane for metal frames complete all as specified and as diected.

S &F 3 mm Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and as diected.

S & F Neoprene/ EPDM rubber gasket complete all as specified and as diected.

S&F 100mm long butt hinges, stainless steel medium weight complete all as specified and as diected.

S&F aluminium anodised barrel tower bolt with bolt of length 200mm complete all as specified and as diected.

S&F aluminium anodised sliding door bolts,plate type, with bolt not less than 12mm dia with and including a minimum of 6mm SS bolts and nuts, four on bolt plate and two on staple plate and fixed 300mm long complete all as specified and as diected.

S&F 125mm long aluminium anodised door handles, oval type, complete all as specified and as diected.

M&L for mild steel work as in framed work such as grills, gratting, guard bars, etc confirming to Fe-290 Gde E-165 complete all as specified and as diected.

M&L for Plain cement concrete (1:2:4) type B-0, 40 mm thick as in damp proof course to horizontal or vertical surfaces including necessary form work using water proofing compound as per manufacturer’s instructions and coat of industrial bitumen @ 1.20 Kg/sqm complete all as specified and as directed.

M&L for Roughly squared stone lintels hammer dressed on face and soffits, hoisted, set and pointed in cement mortor 1:6 n.exc 3 m in length complete all as specified and as directed.

S&F joist , channel, angle, tee section, fixed independently without connecting plates etc. including welding as necessary confirming to Fe-290 Gde E-165 complete all as specified and as diected.

M&L for preparation of new steel surface of any description n. exc 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and as diected.

M&L for rolled mild steel in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc of Fe-290 (Gde E- 165) complete all as specified and as diected.

M&L for rolled mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-290 Gde E-165 complete all as specified and as diected.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt not exceeding 5 cm and dia of neck 11 to 15 mm complete all as specified and as diected.

S & F Pre-painted galvatume ( Sand Colour ) aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of sand colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as diected.

S & F Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of sand colour having tensile strength of 550 Mpa as in roof covering /cladding to wall and ridge , fixed with self tapping screws complete all as specified and as diected.

M& L for 75mm thick PCC 1:3:6 type C-1 (Using 20mm gradede crushed stone aggregate) as in plinth protection finished even and smooth without using extra cement and 10mm wide full depth joints at every 3 mtr interval & at turning point shall be provided and filled with 1:1 bitumen & sand mix complete all as specified.

S&F Gl frame work of size of grid 605 X 605mm for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre and gypsum board 12mm thick false ceiling board in grid as per specification complete all as specified and as diected.

S& F Harrison rails,mild steel,curtain rod chromium plated with fixing brackets, stops, rollers etc. complete all as specified and as diected.

M&L for 5cm thick Sand stone slabs in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4 complete all as specified and as diected.

M&L for Jodhpur stone of roof slab self faced 7.5cm to 10 cm thick , 25 cm to 35cm wide ,hoisted and set , jointed and grouted in cement and sand mortar (1:6) complete all as specified and as diected.

M&L for 50mm thick P.C.C 1:3:6 C2 using 40 mm graded stone aggregate as in floors over stone patti roof slab finished the surface even and fair complete without using extra cement complete all as specified and as diected.

S&F PVC low level flushing cistern 10 litres capacity, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe, complete all as specified and as diected.

S&F vitreous china wash down water closet EWC white/ivory/off white (pedestal pattern including all necessary accessories like fixing bolts/gel gasket WC seat cover closed pattern, CP jet spray complete all as specified and as directed.

S&Fvitreous china wash hand basin, white, angle back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, PTMT bottle trap and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified and as directed.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors, 110mm bore complete all as specifed and as directed.

S&F PVC (SWR) pipes, single socketed,in any length with rubber ring joints, fixed to walls, 75mm bore complete all as specifed and as directed.

S&F PVC (SWR) bends/reducer/tee any radius, 110mm bore complete all as specifed and as directed.

S&F PVC (SWR) 110mm couplers,75mm cowel complete all as specifed and as directed.

S&F PVC (SWR) 'P' trap, 110mm bore complete all as specifed and as directed.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement, dia of outlet 75 mm complete all as specifed and as directed.

M&L for 15mm bore steel water tubes, medium grade. ISI marked, galvanised with all fittings, concealed in walls, surfaced on external side or laid in floors complete all as specifed and as directed.

M&L for 20mm bore steel water tubes, medium grade. ISI marked, galvanised with all fittings, fixed to walls and ceilling or laid in floors complete all as specifed and as directed.

S&F angle valves, cast copper alloy, cp fancy type screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, 15mm bore complete all as specifed and as directed.

Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed. Note : (i) The water storage tanks shall be 3 layers, HDPE tanks moulded to seem-less perfection of rotational process. The tanks shall be manufactured only from FDA approved special grade of polyethylene and shall be certified fit for potable water. (ii) The tanks shall white coloured and ISI marked. Also refer paras 18.6 and 18.6A of MES Schedule Part-I. (iii) Payment for inlet, outlet and over flow pipes and ball valve shall be made separately. Howerver cost of providing necessary GI fittings such as nipples with check nuts for inlet and outlet pipes, GI plug with check nut for over flow pipe and 30cm long wash out pipe, GI 20mm nominal bore, medium grade and check nut for wash out pipes of size as per actual requirements as directed by Engineer-in-Charge shall be deemed to be included in the unit rates of this item.

S&F Bib taps cast copper alloy Chromium Plated fancy type with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specifed and as directed.

S&F wall mixer, telephonic type, brass, chromium plated, fancy type, with capstan head handles with lettered 'hot' and 'cold', screwed down high pressure, including CP brass wall flanges and necessary extension nipples screwed for 15mm bore pipe connection, complete all as specified as directed.

S&F Centre hole mixer for mixing hot & cold water for wash hand basin, cast copper alloy, with dual capstan heads, chromium plated, screwed down high pressure, with lettered 'Hot' & 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe suitable for 15mm bore, complete all as specified and as directed.

S & F soap dish any type fixed to plugs with chromium plated brass screws complete all specified and as directed.

S&F Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore (Minimum weight 210 gms) complete all specified and as directed.

S&F toilet paper holder with flat recessed type stainless steel complete all specified and as directed.

S&F Shower rose, round type, brass, chromium plated, Fancy type, 100 mm dia (minimum) with or without swivel joint, with & including CP brass arm and wall flange, fixing to steel pipe of 15mm bore or union complete all as specified and as directed.

S & F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F 40 mm bore PVC waste pipe bottle trap to floor trap concealed in wall complete all as specified and as directed.

S&F tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified and as directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

M&L for Cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate as in packing under and hunching against the sides of pipes, without bedding layer, after they are laid and tested in 150 mm dia of pipe complete all as specified and as directed.

M&L for Salt glazed stone were drain pipes, grade ‘A’ 150 mm bore (internal dia) laid in trenches over existing concrete bedding and jointed complete all as specified and as directed.

M&L for Soakage well of size 1.2m dia and 3 m effective depth, excavation in any type of soil, foundation in PCC 1:3:6, walls of honeycomned masonary with top ring of M-25 RCC concrete including intercepting camber and screen chamber made of brick masonary in CM, RCC cover slab M-25/ SFRC cover, interconnecting pipes or RCC/PVC complete all as specified and as directed.

M & L for conventional RCC Septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, RCC M-30 Design Mix in Walls, Base Slab, Baffle Walls and Roof Slab including beams etc with Vent shaft, manhole openings with cover connection etc. with effective depth of 1.5 meter and overall depth of 3 meter for 25 users DWG BTD-016 complete all as specified and as directed.

M&L for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre area of surface area complete all as specified and as directed.

M&L for treating the back fill in contact with foundation at the rate of 7.5 litres of emulsion per square metre area of vertical surface (area of the sub sutructure in contact with back fill to be measured) complete all as specified and as directed.

M&L for treating the top surface of filled earth and under plinth area at the rate of 5 litres of emulsion per square metre area of surface area complete all as specified and as directed.

M&L for treating the soil along with external perimeter of building at the rate of 2.25 litres of emulsion per metre of the perimetre wall complete all as specified and as directed.

M & L for Point wiring with 2.5 Sqmm (nominal area) single core PVC insulated unsheathed (FRLS) cable, multi-stranded, 1100 volts grade copper conductor, in universal colour code with & including suitable size of rigid non-metallic PVC conduit (not less then 20mm dia med gd) and its all accessories complete concealed in wall/roof incl cutting & chases( making good all to the disturbed surfaces as per existing) including with modular flush metal boxes with modular cover plates & frame for mounting modular switches, sockets, regulators etc and including earth wire of PVC insulated (FRLS) copper conductor multistranded of 2.5 Sqmm size in green colour complete all as specified in current SSR Part-I & II & directed by the Engineer-in-Charge as described below:-

a) One light/ fan/ exhaust fan point controlled by one way switch 5 amp complete.

b) One 3 pin 5 Amps socket point controlled by one way switch on same board.

c) One 3 pin 5 Amps socket point controlled by one way switch on independent board.

d) One bell point controlled by one way switch 5 amp complete.

e) One light point controlled by two 2-way switches.

All as per item No. 93 hereinbefore but for 3 pin / 5 pin 16 Amps sockets outlet with 4 Sqmm PVC insulated & unsheathed (FRLS) copper conductor cable independent Point wiring complete all as specified and as directed.

Supply and Fixing Modular switch 6 Amps single pole one-way, 1 Module complete all as specified and as directed.

Supply and Fixing Modular switch 6 Amps bell push, 1 Module complete all as specified and as directed.

Supply and Fixing Modular switch 16 Amp single pole one way,1 Module complete all as specified and as directed.

Supply & Fixing Modular fan Regulator electronic step type 2M complete all as specified and as directed.

Supply and Fixing Modular socket 2-in-1, 5 pins 6 Amps , combined 2 Module complete all as specified and as directed.

Supply and Fixing Modular socket 2-in-1, 3 pins 6 /16 Amps, combined 2 Module, 230 volt complete all as specified and as directed.

Supply and Fixing Modular switch 6 Amps single pole two-way, 1 Module complete all as specified and as directed.

Supply and Fixing ceiling rose surface bakelite 65mm x 50mm three terminals complete all as specified and as directed.

Supply and fixing lamp holder, PVC / polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

Supply and fixing bell ding dong type 230 volts complete all as specified and as directed.

Supply and fix in sheet metal enclosure with a two pin and earth plug and socket complete with SP MCB of rating 20 Amps, 240 Volts with all connection complete all as specified and as directed.

Supply & fixing indoor decorative ultra slim surface /Wall mounted LED batten tube light complete fitting 1x 20 watt LED Tube fitting with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts,co- related colour temperature (CCT) of 6500K, complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply & fixing indoor decorative ultra slim surface /Wall mounted T5 LED batten tube light complete fitting 1X9 watt LED Tube fitting (size within 600x25x40 mm) suitable for mirror light with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts complete with all accessories complete all as specified and as directed.

Supply and fix LED 9W, suitable for B22 type holder, natural white complete all as specified and as directed.

S&F LED Bulk Head with PDC aluminium housing and milky diffuser capacity 10 Watt complete with all accessories and connection complete all as specified and as directed.

Supply and install of 35W LED building security light fitting with lens & driver, powder coated pressure die cast aluminium, top opening and maintainable with heat resistance toughened glass, built-in Short-Circuit Protection, Over voltage Protection and Surge Protection, IP-65 protection with all connections complete all as specified and as directed.

M&L for building security light bracket made out of 40mm dia light grade GI pipe of 1.2 m length bent to required shape suitable for fixing street light fitting on Steel tubular pole/wall including two Nos clamps made out 40mm X 6mm flat with suitable nuts and bolts complete all as specified and as directed.

Supply & fixing indoor wall mounted fitting, brushed nickel finish fixture with opal glass diffuser, with LED retrofit bulb of capacity 09 watts complete all as specified and as directed.

Supply & fixing MCB distribution board, SPN 12 Way, Double door, sheet steel, phospcomplete all as specified and as directed.

Supply & fix MCB SPN 6-32 Amps,' C' series , bracking cap 10KA, 240V complete all as specified and as directed.

Supply & fix MCB SP 6 - 32 Amps, ' C' series ,bracking cap 10KA, 240V complete all as specified and as directed.

Supply and fix exhaust fan 250mm sweep sturdy engineer plastic body complete with louvers, AC 230 Volt single phase 50 Hz supply and including connecting up with twin core twisted flexible copper conductor cable of suitable size 0.75 Sqmm complete all as specified and as directed.

Supply and fix of ceiling fan, 1200mm sweep with advance energy saving, AC 230 Volt, BLDC type, copper winding, min Air delivery 210 CFM and service value 6, single phase five star rating complete with canopy, down rod, fan blade complete with all accessories, internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed.

Supply and fix water heater storage type,capacity 25 litres, BEE 5 star rated, with connection pipe complete all as specified and as directed.

M&L for Earthing to equipments / panels etc with & including galvanised mild steel earth plate electrode of size 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than 2.25 m below normal ground level) with top edge of the earth plate at a depth not less than 1.5 m below ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides, connected to & including galvanized mild steel strip 32x6 mm as earth lead, including nuts, bolts, check nuts & washers of galvanized iron or steel and riveted/welded to earth plate at one end and other end of strip connected to transformer / GOD / Panel / equipment body / test point with two Nos nuts bolts or welding with steel structure, GI earth strip encased in and including 40mm bore GI light grade pipe with all fittings from upper edges of earth plate upto 7.5 metre above ground level fixed with and including 25x3mm flat iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe medium grade from earth pit to top of electrode and including funnel, wire mesh, copper lugs etc complete with earth pit in PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate and 40mm thick RCC (1:2:4 type B1) cover complete all as specified and shown in electrical plate No 3 of SSR Part-I including necessary excavation and earthwork in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance not exc 50m complete all as specified and as directed.

Cutting existing steel tubing of size 50mm bore for alterations or additions (each cut measured) done in position without taking down complete all as specified and as directed.

Screwing existing steel tubing for alterations or additions (or lenghtening screw on pipe to form connector) done in position without taking down complete all as specified and as directed.

M&L for steel water tubes, medium grade, galvanised, with all fittings , laid in trenches fixed to wall of size 50mm dia and connecting with existing lines with suitable GI Tee including testing complete all as specified and as directed.

M&L for steel water tubes, medium grade, galvanised, with all fittings , laid in trenches fixed to wall of size 25mm dia and connecting with existing lines with suitable GI Tee including testing complete all as specified and as directed.

M&L for Gun Metal gate valve with iron wheel head, screwed both ends for iron pipe of size 25mm dia complete all as specified and as directed.

Supply and laying un-reinforced precast concrete cable cover class LV type I flat of size 250mm x 150mm x 40mm all as specified factory made ISI marked complete all as specified and as directed.

M & L for sand cushioning to PVC under ground cable with screened and washed sand and punning to provide a required cover complete all as specified and as directed.

Supply, installing, commissioning and testing of bus bar chamber outdoor type, cubical type made out CRCA sheeet 3.15 mm thick dust and vermin proof and angle iron of suitable size, pedestal flame grouted in PCC (1:2:4) type B-1 20 mm graded stone aggregated thimble and cable entry boxes with cable glands, bus bar should covered from all sides with front and back complete with 200 Amps (phase) & 200 Amp (Neutral) rated aluminium bus bar of suitable size, including painting with two coats synthetic enameled paint over a coat of red oxide primer and consisting of the following:- (a) MCCB 100 Amp, 4 pole, 415 V, 25 KA-01 Each (01 In-coming) (b) Digital Amp meter (0-250) -01 Each (c) Digital Volt meter (0-500)-01 Each (d) RYB Indicator -01 Set

M&L for Earthing complete with galvanized steel earth plate electrode 600x600x 6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meter below normal ground level connected to galvanized iron strip 32x6mm as earthing lead by means of bolts, nuts, check nuts and washer of galvanized iron or steel all as shown in electrical plate No 3 of SSR Part-I connected to panel/pole/bus bar complete all as specified and testing on completion, including provision of earth wire protected by 40mm dia GI light grade protection pipe from test point to main board and 20mm GI medium grade watering pipe funnel, PCC earth pit and RCC cover charcoal, salt and GI wire including excavation and earth work etc complete all as specified and as directed.

Supply, laying, jointing and testing of XLPE insulated, sheathed, armoured, heavy duty LT 1100 volts grade cable with aluminium conductor of size 25 sqmmx 3.5 core laid in trenches / duct / fixing on walls / poles or passing through pipe including connecting with suitable lugs, glands, nuts and bolts in existing Panel from pole / Main Panel Box and testing complete all as specified and as directed.

J.M.D. CONSTRUCTION CO. (BID ID -3385719)