SPECIAL REPAIR AT RATION DISTRIBUTION POINT (RDP) BLDG NO T-25 T-03 AND T-60 AND OR LIVING LINE BLDG NO T-13 OF 226 COY ASC (SUPLLY) TYPE G UNDER GE (WEST) DELHI CANTT-10

Amount

Dismantling plain or corrugated steel sheeting any gauge, thickness, including Nanital or similar pattern roof coverings.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings as specified.

S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and including cutting chasing of wall, complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling timber framed work scantlings 40 sq. cm and over in section, in any position complete all as specified and directed.

S&F rolled MS work in roof trusses (framed), trussed, purlins, rafters including cleats, distance pieces, gusset & base plates, fixture & fastenings etc welding, drilling etc complete conforming to Fe-410-W (Gde-E-250) quality A complete all as specified and directed.

Demolition of Brickwork built in cement mortar including all quoins, arches, pillars etc and precast articles including disposal of demolished material as directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6m mean radius and built in cement mortar 1:6 complete all as specified and directed.

All as per item no. 8.00 here-in before but half brick wall built in cement mortar 1:4.

Demolition of reinforced cement concrete in any description and position.

M&L for formwork to soffits of suspended slabs such as floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) flat rough finished surfaces of concerete completed all as specified and directed.

M&L for formwork to edges of concrete flats, treads,openings in walls and roofs etc n exc 20 cm wide, horizontal or sloping and similar work, flat rough finished surfaces of concerete all as specified and directed.

M&L for mild steel TMT bars upto 10mm dia and over cut to length,bent to shape required including cranking, biniding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for reinforced cement concrete Nominal Mix using type B-1, 1:2:4 (20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landing, balconies, canopies, deck slabs and in shelves and the like concerete all as specified and directed. (Note :- Steel reinforcement bars shall be measured and paid separately under relevant items)

Taking down cement plastering on brick walls/stone walls/ ceiling etc. incl racking out of joints hacking for key scrubbing down with water and disposal of rubbish all as specified and directed.

M&L for 15 mm thick Ready mix mortar cement plastering on walls in CM 1:6 on fair / unfair faces of brick work or concrete surfaces finished even and smooth without using extra cement as specified.

-ditto- but in CM 1:4.

M&L for 5mm thick (RMP) cement plastering in CM 1:3 on fair/ unfair faces of brick work or concrete in ceilings all as specified.

Dismantling of ceiling board (Pulp insulation or insulation etc) or insulation board any thickness including cover fillet all as directed.

M&L for anodised aluminium snap grid frame work, size of grid 605 x 605 mm for false ceiling, Hangers 6 mm dia GI (upto1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long, 4 mm thick non asbestos fibre building boards, ordinary type, fixed to timber/alum/GI frame work with screws complete all as specified.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame complete all as specified & directed.

S&F solid PVC wall lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified & directed.

M&L for three coats of white wash on walls / ceiling incl prepration of new plaster surfaces complete all as specified and as directed.

M&L for preparation of newly plaster surfaces and applying two coats of oil bound distemper by using roller over a coat of primer over a coat of sanded prepared surface of wall care putty not less than 1mm thick, as per manufacturer instructions complete all as specified and directed. (Note : Work to be done through applicator approved.

M&L for preparation of newly plaster surfaces and applying two coat of cement base paint over a coat of primer complete all as specified and directed. (Note : Work to be done through applicator approved.

Dismantling floor, hearth or wall tiling including cement mortar bedding and rubbish off the premises complete all as specified & directed.

M&L for vitrified ceramic tiles of dark shade, 8-10 mm thick (Square/recatangular) polished of area not exceeding 0.36 Sqm each tile (600mx600mm) in floor, set and jointed in neat cement slurry and pointed in coloured CM with tiles laid over & including 15mm thick cement screed 1:6 complete all as specified & directed.

M&L for glazed ceramic tiles on vertical surfaces, each tile 350x 450x7mm/ 350x 600x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including plaster 10mm thick cement mortar 1:4 matching with floor tiles complete all as specified & directed.

M&L for non - skid ceramic coloured joint free tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and incl. cement screed bed 20mm thick in cement mortar 1:6 complete all as specified & directed.

M&L for 18-20 mm thick granite slabs (table rubbed and polished) in steps, jambs, pillars, window sills, cooking platforms, shelves etc and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite laid over & including 20 mm thick cement screed bed 1:4, incl rubbing & polishing complete all as specified & directed.

M&L for machine cut kota stone slab flooring 20-25mm thick in floor laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including mirror finish polishing over and including cement screed 20 mm thick in cement mortar 1:6 complete all as specified and directed.

M&L Machine cut kota stone slab 20-25mm thick skirting, riser of steps & pillars & likes (with groove lining for anti slippery for stair case) over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for Providing edge moulding to 20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete complete all as specified & directed.

Demolition of cement concrete in ground floor n exc 15 cm thickness (below or above ground level) and removing the demolished material and debris away from defence area.

M&L for 75mm thick PCC 1:4:8 type D2 ( 40mm graded stone agg ) as in sub base of floor complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C2 ( 40mm graded stone agg ) as in plinth protection finished even and fair w/o using extra cement, grooves filled with bitumen mastic filling of mix (1:2) (bitumen and sand) complete all as specified and directed.

M&L for cement concrete type B21 1:2:4 (20mm graded agg) in coping , Kneeler, Kerb, bed block etc complete all as specified & directed.

Taking down of chowkat or frame (w/o taking off shutter from frame) n exc 1.50 Sqm and incl builder hard ware fittings as directed.

All as per srl item No 38.00 here-in-before but exc 1.5 Sqm and n.exc 4 Sqm.

S&F powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc.(minimum thickness of powder coating 50 micron) complete all as specified & as directed.

M&L for powder coated aluminium ventilator, openable, top hung and bottom portion fixed type without sash bars with aluminium section of weight 0.55 kg/RM including glazing, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws and top hung shutter fixed hook & eye minimum one no. on each shutter, one no. aluminium tower bolt 100mm long and 75mm long aluminium handle in each shutter etc. complete all as specified and directed. Note : glazing, wire mesh shall be measured and paid separately against respective items.

S&F powder coated (minimum thickness of powder coating 50 micron) aluminium sliding three track window, three shutter Series B (SHUTTER SECTION-18mm) with two glazed shutters each covering one third opening and one gauged shutter covering one third opening including self closing locking arrangement, stoppers and rubber beading gasket without sash bar aluminum section weighing 1.06 Kg/RM including necessary jointing cleats glazing clips rubber packing powder coated aluminum beading screws including fittings in each shutter with 5 mm thick tinted glass & also including stainless steel wire cloth of 0.36 mm dia and avg width of aperture 1.40 mm complete all as specified and directed. Note:- Three way track sliding window of frame size 92x31.75x1.5 mm and shutter size 40x18mm with 9mm interlocking leg x 1.45mm thick and weight not less than 0.607kg/RM.

S&F aluminium door single leaf with powder coated aluminium frame of section 62.5x37x1.5mm thick, shutter with bottom & middle rail of section 112.50x 37x1.5mm thick and styles & top rail of section 83x37x1.5mm thick with centrally locking arrangement with lock make of ‘GODREJ’ or ‘LINK’ & hydraulic door closer, 4.8 mm thick tinted glass with rebate including joining cleats, fixing of builders hardware fittings, necessary floor springs, glazing with 5mm thick frosted glass including necessary fittings, fixtures & aluminium snap beads complete all as specified and directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing of Fe 410 -W (Gde-E- 250)-A quality-complete all as spd and directed.

S & F 35 mm thick hardwood glazed and skelton shutters, open rebated & prepared to receive glass ,gauge etc. (with or without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR part-I section 8 clause 8.24 (a) complete all as specified and directed.

S&F 2nd class hardwood 35 mm thick plain framed panelled shutters (any number of panels) with panels of timber flat on both sides/ feather edges of veneered particle board medium density wood particle board with commercial face veeners complete all as specified and directed.

M&L for MS in plates (plain or chequered) channels, square cut to notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed

M&L for preparation of new wooden surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a caot of pink primer complete all as specified and directed.

M&L painting two coats of synthetic enamel paints over a coat of red oxide primer on new steel surfaces exc 10cm girth including preparation of surfaces complete all as specified and directed.

S&F Alumn grill deco pattern, 8 to 10mm thick with separate channel to window/ventilator.

M&L for colured plastic mould reflective type cement concrete polished chequred tiles 300x300/400x400x20mm thick machine pressed; set jointed and pointed with white cement and pigment over 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L 100mm thick cement concrete 1:4:8 type D-2 using 40mm graded aggregate including finishing rough surfaces without using extra cement

S&F glass fibre reinforced plastic (FRP) door frame shall be three legged of cross section 90mmx45mm having single rebate of 32mmx15mm to receive shutter of 30mm thickness. The laminate door frame moulde with fire retardant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fibre glass from all sides. MS stay shall be provided at the bottom to steady the frame as per specification & drawing complete all as specified and directed.

S&F 30mm thick glass fibre reinforced plastic (FRP) panelled door shutter of required colour and approved brand and manufacturer made with retardant grade unsaturated poyester resin moulded to 3mm thick FRP laminate for forming hollow rails and styles with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5mm thick FRP panels and confirming to IS 14856-2000 supply and fixing in the frame at site complete all as per specification & drawing complete all as specified and directed.

S&F 4mm thick Figured glass, pin head type and glazing with oil putty in each pane fixed in bottom two pane in windows etc complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia or wire and an average width aparture 1.18 mm and fixed with tinned tack or stainless steel wire staple complete all as specified and directed.

S&F 100 mm butt hinges medium weight cold rolled mild steel complete all as specificed and directed.

S&F 150mm long aluminum anodized barrel tower bolt of extruded section complete all as specified and directed.

S&F 150mm long aluminium handles cast type anodised ISI Marked.

S&F aluminium alloy anodised sliding door bolt with hasp and stapple (bolt type) and fixing of clips of sheet cast or extruded section fixing bolts sliding bolts of extruded section or cast alum 300mm.

S&F in repair 25mm dia SS curtain rods including SS bracket, holder and side knobs etc all necessary fittings as per site requirement complete all as specified and directed.

S&F brass CP tubular towel rail, 20mm dia, D type, 60cm long between flanges fixed in repairs.

S&F Soap dish, statiless steel CP, approximate size 160x 160 mm fixed to wall complete all as specified and as directed.

S&F in repair stainless steel kitchen sink 1mm thick with drainage board with plugs, washers, wastes, incl bedding in cement mortar to dwarf wall or incl. fixing cantilever brackets and connecting union to pipe over all size 915x460 bowl size 410x330x160mm complete all as specified and directed.

S&F in repair vitreous chaina WHB of size 550x400mm white flat back fixed on brackets, incl. 1 no. pillar tap fancy type, cast copper alloy with capstan heads CP screwed down high press with long screwed shanks & fly nuts, waste fitting of brass CP 32mm bore and PVC waste pipe 32mm bore 90cm long, including PVC connection size 45cmx15mm with PTMT nuts complete all as specified and directed.

S&F 32mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F 32mm dia and 90cm long PVC waste pipe complete all as specified and directed.

S&F 15mm dia Brass CP wall/WHB/sink mixer for mixing hot & cold water screwed down for iron pipe including all necessary arrangement etc, complete all as specified and directed.

S&F 15mm bore dia stop valve cast copper alloy, screwed down high pressure but fancy type, chromium plated (stop valve/angle valve) with crutch, screwed both ends for iron pipe or for unions and fixed in repair complete all as specified and directed.

S&F in repair 75mm bore cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F in repairs salt glazed stone ware gully traps 150 x 150mm square mouth `P' type complete all as specified and directed.

S&F in repairs vitreous china squatting pan, 'Orissa pattern' size 580 x 440mm white with integral foot rests incl. flush pipe of polyethylene of low or high density, connection to 'P' or 'S' trap and to flushing pipe, anti syphonage pipe, etc. complete trap set in concrete & incl. S&F 100mm CI sanitary connection socket to fit WC out-let complete all as specified and directed.

S&F Vitreous China wash down water closet pan (pedestal pattern), white including fixing bolt, flush pipe of polyethylene of low or high density, connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including 100mm cast iron sanitary connection socket to fit WC out-let complete all as specified and directed.

S&F in repair vitreous china urinal, bowl (back wall) type flat back, of size 465x355x265 mm white, with grating and union for discharge pipe, incl providing & fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with & incl 60 mm long brass screws, pointing around urinal back in cement, incl fixing 5 ltr cap PVC automatic flushing cistern with brackets & flush pipe of polyethylene of low or high density or PVC 32mm dia, waste coupling of PTMT (half or full threaded) bore dia of discharge pipe 32 mm (Minimum weight 32mm-45gms, incl PVC connections 15mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F toilet paper holder with flat recesed type stainless steel fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

S&F 75 / 100mm dia CI sanitary connection short connection pipe of length upto 300mm complete all as specified and directed.

S&F 75 / 100 mm dia CI branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S&F in repairs salt glazed stone ware gully traps 150 x 150mm square mouth `P' type complete all as specified and directed.

S&F 100mm bore cast iron 'P' Traps complete all as specified and directed.

S&F in repairs 10 Ltrs capacity PVC low level flushing cistern complete with syphone handle lever PVC bend including connecting to WC and fixing on walls with bracket all as specified.

S&F in repairs PVC Connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F 20mm bore gun metal globe or gate valves with iron wheel, screwed both ends for iron pipes fixed complete in all respect as specified.

Dismantling existing water tanks capacity exc 500 ltr but not exc 1000 ltr complete all as specified and directed.

S&F 1000 ltrs capacity rotational molded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia complete all as specified and directred.

Taking up or down 15mm dia bore of galvanised Iron steel tubing and connections including cleaning for refixing, cutting/chasing in wall/floor complete in all respect as specified.

All as per srl item No 87.00 here-in-before but20mm bore

S&F 15mm bore dia of medium grade galvanised steel tubing with all fittings and fixed complete to wall or laid in floor complete in all respect as specified.

All as per srl item No 89.00 here-in-before but 20mm bore

S&F Cast iron soil, waste and vent pipes 100mm bore sand cast in any length with or without ears, with lead joints, laid in trenches or in floors including disamntling of existing PVC/SWG pipe and jointing to GT and Manholes pipes complete all as directed.

All as per srl item No 91.00 here-in-before but 75mm bore.

S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed.

S&F of 18/19mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination including sealing the ends using Ist class HW beading 12mm thick as in cupboard shutters fixed with screws to timber frame work/frame complete all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps (when open) in mm 40mm (Suitable for 18 mm thick cupboard shutters) complete all as specified.

S&F hasp and staple 150 mm size , safety type, aluminium anodised, with mild steel hinge pin incl bolt to hinge plate and fixed with screw.

S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

Taking down carefully copper/aluminium point wiring from wooden battan or conduits (light, fan, socket or power) complete including (fittings such as switches, ceiling roses, pendants, regulator, sockets etc. to be measured separately) and making good disturbed surfaces of walls, floor etc.

M & L Concealed Point wiring complete with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through and including non-metalic rigid PVC conduit medium grade ISI Marked and all conduit accessories concealed in wall/on surface conduit for ceiling/truss/columns portions etc and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuity conductor,including fabricated branded modular metal flush box duly make embossed, concealed in walls with suitable modular inner and outer plate for housing modular switches , socket outlet and fan regulators etc , all as specified and directed for the followings:-

(a) One light/Fan/Exhaust Fan point controlled by one switch

(b ) One socket outlet point 5 Amps on independendent board

(c ) One socket outlet point 5 Amps controlled by one switch on same board along with other switches.

All as per item No 102.00 here-in-before but with 2 core copper conductor cable FLRS 2.50 sqmm for one 3 pin modular socket outlet,15 Amps concealed and including provision of 2.50 Sqmm PVC insulated copper conductor cable as earth continuity conductor on independent board.

Supply and fix switch piano type single pole one way 6 Amps all specified and as directed.

Supply and fix switch piano type 15 Amps one module single pole one way.

Supply and fix socket outlet multipurpose 2/3 pin 5 amp flush button type complete all as specified and as directed.

Supply and fix socket outlet multipurpose 2in 1 5 and 15 amp flush button type complete all as specified and as directed.

Supply and fix ceiling fan regulator, step type for ceiling fan 120 W 2 module .

M & L for Decorative walll light fixture made up of Polycarbonate, Spiral B-22 Base all as specified.

S&F of LED bulb of 9 watt complete all as specified and directed.

Supply, laying and drawing submain wiring in and including 20 mm dia concealed PVC rigid conduits including cutting of chases for laying conduit making good the surfaces as per existing surfaces or as directed on walls 02 runs of IC x 6.00 sqmm (Main Cable and neutral) and one run of IC x 6.0 sqmm (as earth wire) of multistranded copper conductor PVC insulated unsheathed cables of 1100 volts grade conforing to IS : 694 of 1990 complete including connection all as specified and directed.

Taking down ceiling fan, sealing cable end, dismantling blades and removing fan and blades and depositto MES store to store complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods,remote and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

S&F of factory made epoxy polyester powder coated distribution board SP & N 8 way fabricated from minimum 1.6 mm thick CRCA sheet with metal double door (IP-43 protection ) fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, eath bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as incomer and 6 SP MCBs as outgoings complete all as specified and conforming to IS: 8623 alongwith cable end box for above DB all as specified and directed. NOTE (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

S&F of factory made epoxy polyester powder coated distribution board TP & N 4 way (VTPN MCCB DB) with metal double door (IP-54 protection) fabricated from minimum 1.6 mm thick CRCA sheet and fixed on wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with provn for DPX 160, 4 pole MCCB and ELM as incommer and 12 SP MCBs outgoings complete all as specified and conforming to IS: 8623 along with cable end box for above DB including taking down old DBs all as specified. NOTE :- (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

S&F in of MCCB 125 Amp 4 pole 16 KA at 415 V with fixed thermal megnatic release complete all as specified directed.

S&F of single pole MCB 6 to 32 Amps, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 including taking down old MCB's complete all as specified and directed.

S&F of SPN MCB 32 amp, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘C’ curve, 10 KA breaking capacity, complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.complete all as specified and directed.

Supply and fixing LED Building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. complete all as specified and directed.

S&F ceiling rose 3 phase/PVC/polycarbonate isolated body complete all as specified and directed.

S&F of single pole MCB 40 Amps, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 including taking down old MCB's complete all as specified and directed.

M&L far Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, burieddirectly in ground (earth pit not lessthan 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion all as specified and directed.

Supply and fix exhaust fan 300 mm sweep with blade and frame including louvers complete all as specified and directed.

S&F replacement of Flate panal Aesthetically designed 2x2 LED flat panel for surface mounting which provides soft-light and glare free symmetrical illumination 34 watt complete all as specified and directed.

S&F in repair of Environmental friendly,ultra modern, energy saving, surface mounted,decorative oval bulk head edgy-fit LED 10 watt 6000 K luminaire comprising of high brightness LEDs complete all as specified and directed.

S& F in repair single pole and neutral enclosure with a two pin earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and directed.

Supply laying testing and commissioning of XLPE insulated armoured heavy duty electric cable with aluminumstranded copper conductor 1100 volt grade crosssectional area 16 Sqmm 2 core LT cable complete all as specified directed.

S&F of electric storage water heater of capacity 25 ltr BEE 5 star with vtreous enamel coating with all accessories and fittings arrangements (PVC Connection) and testing after installation complete all as specified and directed.

M/s Verma and Co

M/S Yamin

MINHAS CONSTRUCTIONS

PBS Construction Co

Vipul Construction

HIND CONSTRUCTIONS

Shiv Shankar Nirman Co.