Development and providing wayside facilities at main junction to the Temple tourist destinations in Survey no 56 of 3 of Village Orgao of V P Tivrem Orgao Ponda Goa

Amount

CIVIL WORKS

Clearing grass and removal of rubbish upto a distance of 50 m outside the periphery of the area

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sq.m on plan) including disposal of excavated earth lead upto 50 m and lift upto 1.5m disposed earth to be leveled and neatly dressed including providing barricading, danger lighting guarding as directed in : All kinds of soil

Earthwork in excavation by mechanical means (hydraulic excavator) / manual means in foundation pipeline trenches drain (not exceeding 1.5 m in width or 10 sq.m. on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. b) All types of Ordinary rock including all types of laterite rock, blasting prohibited

Refilling the pipeline/foundation trenches plinth sides, foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50 M and all lifts and disposal of surplus earth as directed by Engineer .

Supplying and filling in plinth under floors, trenches including watering ramming consolidating, dressing, complete. Sand

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Laterite masonry in neatly dressed stones for 23 cms thick masonry walls in c.m. 1 : 4 (1 cement : 4 coarse sand in foundation upto plinth level

Extra for laterite masonry in all sizes in superstructure from floor I level upto floor V level.

Half brick masonry usign fly ash bricks in cement mortar 1:3 (1 cement : 3 coarse sand ) with bricks of class designation 40 kgs / cm2. Above plinth upto floor V level 200 x 95 x 95

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggregate 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: a) All work up to Plinth level

Providing and laying in position ready mixed concrete (RMC) with usage of Ordinary Portland Cement manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead upto 10kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C., from the transit mixer to the site of laying, excluding the cost of centering, shuttering, finishing and reinforcement including the cost of admixtures in recommended porportions as per IS : 9103 to accelerate/retard setting of concrete, improve workability without imparing strength and durability as per the directions of the engineerin-charge. All works upto floor V level M-25grade of concrete

Providing and laying upto floor five level cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggregate 20 mm nominal size) including smooth finishing to exposed surfaces, with cement mortar 1:3 (1 cement: 3 fine sand) including centering and shuttering etc. String courses, copings, bedplates, anchor blocks, plain window sills and the like.

Centering and shuttering including strutting, propping, & removal of form for Foundation, footings, bases of columns

Centering & shuttering including Strutting, Propping & removal of forms for : Vertical surfaces such as retaing walls, return walls, Partitions, walls (any thickness) including attached Pilasters, Buttresses, Plinth and string courses, Fillets and the like

Centering and shuttering including strutting, propping, & removal of form for Columns, Piers, Pillars, Aburments, Posts and struts (square rectangle polygon in plan)

Centering and shuttering including strutting, propping, & removal of form for Sides and Soffits of beams, Beam Haunchings, Cantilever, Girders, Bressumers and Lintels plinth beams not exceeding 1m in depth

Centering & shuttering including Strutting, Propping & removal of forms for : Suspended floors, roofs landings, shelves & their supports

Providing TMT steel reinforcement bars of (SAIL, TATA. VIZAG, JSW Steel Ltd.) ) (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member.

Steel work welded (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only)in built up sections trusses and framed work including cutting, hoisting, fixing in position and applying priming coat of red lead paint. b) In tees, angles, flats and channels

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section (CHS) IS1161 closed Structural Steel of approved make (Min Yeild Stress 310 Mpa)) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Providing & fixing Upvc Door Frame Yashashri make or equivalent made out of Upvc extruded multi cavity frame of 60 mm x 60mm x 2mm wall thickness. Frame is reinforced with G.I. Channel & welded in corners with Average weight 0.80 kg per running mtr. These frames are tested by using BS 2782 & DIN 53459 test methods.

Providing & fixing 20 mm door shutter Yashashri make or equivalent, made by using 20mm x 155mm x 1.2mm upvc multi-cavity section and boarder of 30mm x 40mm x 2.5mm Upvc multi cavity section. The corners are joined by inserting polymetric corners & hardware used for fixing the door shutter is stainless steel hinges & S. S. handle & S.S. tower bolt. The average weight of 20mm door shutter is 4.60kg per sq mtr. These Upvc sections are tested by using BS 2782 & DIN 53459 test methods.

Providing and fixing bright finished brass door latch with necessary screws etc complete 250 x 16 x 5 mm

Providing & fixing bright finished Stainless Steel SS 304 grade Aldrops with screws etc. complete. 250 x 150mm. All works complete as per the drawing, specification and direction of the Engineer-In-Charge-In-Charge

Providing and fixing Stainless steel D type handles with necessary screws etc complete a) L 300mm/325mm x 22 to 25mm dia

Providing and fixing chromium plated brass butt hinges with necessary screws etc. complete 125 x 70 x 4.0mm (ordinary type)

Providing and fixing bright finished brass tower bolts (barrel type) with screws etc. complete 200 x 10 mm

Providing and fixing bright finished brass tower bolts (barrel type) with screws etc. complete 150 x 10 mm

Providing FRP door shutters 35mm thick with frame size in clear opening of 0.75x2.10m hinges and screws complete.,

Providing and fixing anodized aluminum ventilators (including frame and shutter ) with three partitions with 5 mm thick approved clear float glass in one partition, Exhaust opening in one partition & 6 mm thk glass louvers in one partition with using weight and size of section not less then as specified or as shown in drawing ,locking arrangement,silicon sealant ,EPDM gaskets, including all aluminum fixture and fittings etc. complete . All gaps between civil work and aluminium frames shall be sealed and made watertight by applying silicone sealant.Rectangular tube @0.478kg/m

Providing and and laying antiskid floor tiles 12 x 12 upto 16 x 16 in of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete a) Dark Shades

Providing and fixing 1st quality ceramic glazed wall tiles (Johnson, Somany, Kajaria )conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade complete. Wall Ceramic Glazed Tiles : 300 x 600

Providing and laying factory made Shot blasted cement concrete interlocking paver block of minimum M35/M40 grade made by heavy duty block making machine with strong vibratory compaction and of aprpoved size and design / shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand, etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Square etc. shapes. The products should comply to IS 15658:2006 and manfucatured by ISO9001: 2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm. c) 80 mm thick in all colours except grey (M40 grade)

Providing and laying factory made Shot blasted cement concrete interlocking paver block of minimum M35/M40 grade made by heavy duty block making machine with strong vibratory compaction and of aprpoved size and design / shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand, etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Square etc. shapes. The products should comply to IS 15658:2006 and manfucatured by ISO9001: 2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm.d) 80 mm thick in grey colour (M40 grade)

Providing and laying factory made Shot blasted cement concrete interlocking paver block of minimum M35/M40 grade made by heavy duty block making machine with strong vibratory compaction and of aprpoved size and design / shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand, etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Square etc. shapes. The products should comply to IS 15658:2006 and manfucatured by ISO9001: 2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm. 60 mm thick in all colours except grey (M35 grade)

Providing and laying factory made Shot blasted cement concrete interlocking paver block of minimum M35/M40 grade made by heavy duty block making machine with strong vibratory compaction and of aprpoved size and design / shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand, etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Square etc. shapes. The products should comply to IS 15658:2006 and manfucatured by ISO9001: 2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm. 60 mm thick in Grey colour (M35 grade)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqm a) Jet Black

Providing 25 mm thick cuddapah slabs machine cut and polished on either side in partitions including making necessary grooves in the wall and fixing with cement mortar, complete as directed by the engineer-in-charge

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite/Cuddapah stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Kotah stone slab flooring over 20 mm (average) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) 20 mm thick.

Providing and fixing Granite stone slabs (mirror polished) 18mm thick in risers of steps, skirting, dado and pillars laid on cement paste and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete

Providing and fixing waterproofing treatment to sanitary blocks consisting of layers of Laterite stone coba of 75 mm thick in cement mortar 1:2 sand witched between two layers of cement mortar 1:4 (20 mm thick ) mixed with water proofing compound, top finishing coat of cement slurry 6 to 12 mm thick with water proofing compound etc. complete with 32 mm dia PVC pressure relief pipe of adequate length including waterproofing treatment to 750 mm height (maximum) of side wall, and bottom surface in cement mortar 1:4 with waterproofing compound and covering 10 years guarantee on court fee stamp of Rs. 100 with ponding test including all lead, lift etc. complete as directed by Engineer.

Providing and fixing colour coated galvulium roofing sheets of 0.5mm thickness including all the accessories (TATA make) but excluding the cost of purlins, rafters, trusses, flashings etc. complete as per the directions of the Engineer in charge.

Providing and fixing Prince or equivalent make PVC SWR half round eaves gutter with bolts, nuts and flat iron brackets 40 x 3 mm size complete. 140 mm nominal size

Extra for providing flat iron bracket 50 x 3 mm size instead of 40 x 3 mm size with necessary bolts nuts, washers etc. for fixing A.C. gutters to purlins.

Extra for providing and fixing prince or equivalent make PVC SWR short stop ends for socketed half round eaves gutters. 140 mm nominal size

12mm cement plaster 1:4 (1 cement : 4 fine sand)

6mm cement plaster to ceiling 1: 3 (1 cement : 3 fine sand)

18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge.

Extra for providing and mixing water proofing material proportion recommended by the manufacturers. (a)12mm cement plaster 1: 3 (1 cement : 3 sand)

Painting three or more coats with acryllic exterior paint of approved brand and manufacture (such as weather shield,APEX) including applying one coat of cement primer and one coat of surface treatment etc. complete.

Wall painting (two or more coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade.

Painting (two or more coats) with synthetic enamel paint of approved brand and manufacture in all shade or new work over and under coat of suitable shade with ordinary paint of approved brand and manufacture to give an even shade

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Dismantling steelwork in built up sections in angles, tees, flats and channels including all gusset plates bolts, nuts, cutting dismembering and staking within 50 mts. Lead

Dismantling asbestos sheet roofing including ridges, hips valley and gutters and stacking the material within 50 meters lead.

Carting away unwanted excavated material such as soil, lime, moorum, building rubbish, laterite stone, Excavated earth, ordinary rock etc. from site lead of 5 km including all loading & unloading charges ( A ) ( by mechnaical Automative Transport ) Contractor should arrange land for dispose up these material at his own cost Lead upto 5 km.

Supplying and fixing Pre-cast cement concrete kerb-stones(factory made,the factory should be ISO certified and registered under Dirctorate of Industries, Govt. of India) of M-20 with 20 mm nominal size granitic/basaltic aggregate properly consolidated by mechanical plat-form and vibrators with smooth finish including fixing at site complete as per specification.

Providing & Installing following type of play equipments of approved make and design and installed as per specification including all taxes , transportation and labour etc complete FRP wave slide

Providing & Installing following type of play equipments of approved make and design and installed as per specification including all taxes , transportation and labour etc complete Standard see-saw

Providing & Installing following type of play equipments of approved make and design and installed as per specification including all taxes , transportation and labour etc complete 2 seater arc swing

Providing & Installing following type of play equipments of approved make and design and installed as per specification including all taxes , transportation and labour etc complete Spring Toys

Supply, fabrication and installing in position MS gates of required width and height of including wicket gate and Rolling Gate(if necessary) of approved size made of channels joists, angles, plates, pipes and MS sheets including stiffeners, bracing, fabricated hinges, MS aldrops locking arrangement, tempered steel pivots, guide track of MS tee, ball bearing arrangement, casters wheels etc. all complete as per drawing, specification and as directed by Engineering in charge all complete. The main entrance gate shall be fabricated out of Mild steel sections completed with applying a priming coat of approved steel primer and two coats of synthetic enamel painting. The structural steel works for gates shall include supply, fabrication, transportation, erection of structural steel gates complete with placing in position embedded parts in concrete / brickwork and in road surface including cutting, grinding, drilling of holes, welding and painting etc complete

Providing and fixing R.C.C. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggreate granitic or basaltic stone aggregate 12.5 mm nominal size) benches including finishing and plastering the exposed surface with cement mortar 1: 3 (1 cement : 3 fine sand) thickness not exceeding 6mm on exposed surface to give smooth and even surface except on the seat & the back of the bench which shall be of marble mosaic chips finished, rubbed and polished to granolithic finish top layer 6mm thick with white black coloured marble chips of sizes from smallest to 4mm nominal size laid in cement marble powder mix 3: 1 (3 white cement : 1marble powder) by weight in proportion of 4 cement marble powder mix : 7 marble chips by volume with under layer 12mm thick cement plaster 1: 3 (1 cement: 3 coarse sand) incl. finishing the rear and bottom sides with waterproofing cement pant of approved brand and required shade (3 or more coats) to give an even shade complete

Providing & fixing Metal Equestrian Statue of Chh. Shivaji Maharaj of Height 25 Feet, Width 10 Feet, Length 18 Feet, Material : Gun Metal + M.s, Weight 7 Ton +, Color: Black Oxidise + P.O Coating with Laker, Erection by Inclusive heavy crane transportation, etc complete..As dirrected by Engineer in charge

Providing and Fixing of Natural black basalt stone of size 300 X 300 X 40mm and laying the same on side wall cladding for foundation at Shivaji Maharaj Statue.

Providing & fixing Granite Cobbles of approved size in100x100x 60 mm thk & Colour on with strong vibratory compaction and of aprpoved size and design / shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand, etc. all complete as per the direction of Engineer

Providing & Fixing MS pipes of size 250 mm dia and Flag Pole of 15.5 mtr height with fabrication, Including cutting, welding, grinding, applying one coat of primer & two coats of metal paint, Providing Nut & Bolts with MS plate of size 500X50 X16 mm with fixing welding & erection complete.Along with supplying and making of flag as per dimension and design provided by Engineer in charge Making foundation & erection by heavy crane Inclusive transportation, etc complete.

Constructing soak pit 1.20m x 1.20m x1.20m filled with laterite stone aggregate 125 to 180 mm including S.W. drain pipe 100 mm diameter and 1.2m. long complete as per standard design. :

Providing and fixing weepholes with rigid PVC make laid in position with a required slope and level while layingpipes of approved the concrete of retaining wall,wing wall and earth retainig structure complete as directed by the Engineer in charge A) 110 mm dia

PLUMBING WORKS

Proving and fixing white vitreous china Wall Hung type (European Type) water closet with seat and lid with C.I. brass hinges and rubber fittings with flush valve nelson/ similar fully chromium plated with stop cock, wall flanges, flush pipe or elbow and vaccum breaker coupling etc. including chair bracket/rag bolts, cutting & making good the walls and floors where required and concealed seat support - W.C. Pan with white plastic seat and lid

Providing and fixing Hand Shower (Health Faucet) with 8mm dia, ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainless steel flexible hose) and wall hook of approved quality confirming to IS standards. (all EWC including Handicap toilets)

Providing and fixing NICKEL chrome plated copper alloy Fancy Two Way Bib Cock with single knob and wall flange conforming to IS 8931:1993 15mm nominal bore

Proving and fixing white vitreous china water closet squatting pan (Indian type w.c. pan) size 580 mm with 100 mm sand cast iron P. or S trap 10 litres high level P.V.C. flushing cister (of approved make) with fittings, rack bolts 32 mm diameter P.V.C telescopic flush pipe with fit tings and clamps 25mm P.V.C. over flow pipe with specials & mosquito proof coupling of approved municipal design and nylon pull complete cutting and making good the walls and floors where required Long pan pattern W. C. Pan

Providing and fixing NICKEL chrome plated copper alloy Fancy long body bib cock with wall flange Jaquar make or equivalent. Confirming to IS 8931;1993 for orissa pan. 15mm nominal bore

Providing and fixing white vitreous china flat back Large lipped front urinal basin of 590x375x390mm size with Urinal Valve Auto closing system with built in control cock & wall flange with fittings, spreader, R.S. or C.I. brackets, standard size C.P. Brassl flush pipe and spreaders with C. P. brass unions & C. P. Brass clamps with waste fitting as per IS 2556, PVC trap with outlet grating and other couplings in CP Brass complete, including painting, fittings, cutting and making good the walls and floors where required. - Range of one urinal basin

Providing and fixing vitreous china wash basin with RS or C.I. brackets painted white, 15 mm C.P. brass pillar taps C.P. brass chain with rubber plug 32 mm C.P. brass waste of pattern, 32 mm diameter M.I. or C.P. brass trap and union complete, Flat back wash basin size 550 x 400mm with a single 15 mm C.P. brass pillar taps.

Providing and fixing NICKEL chrome plated copper alloy Fancy BOTTLE TRAP ECONOMY TYPE 32MM Jaquar make or equivalent. Confirming to IS 8931;1993

Providing & fixing liquid soap container with C. P. brass lid and brackets fixed to wooden cleats with C. P. brass screws Plastic container

Providing and fixing nahani trap of rigid PVC (approved make) for S.W.R. Pipes including lubricating etc. complete, without door : 110mm

Providing and fixing nahani trap of rigid PVC (approved make) for S.W.R. Pipes including lubricating etc. complete, without door : 75mm

Providing and fixing rigid PVC S.W. R. (soil, waste and rain water drainage pipes of approved make including lubricant etc. complete (single/double) socket-ed : 110mm dia

Providing and fixing rigid PVC S.W. R. (soil, waste and rain water drainage pipes of approved make including lubricant etc. complete (single/double) socket-ed : 75mm dia

Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes of approved including lubricating. 110mm

Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes of approved including lubricating. 75mm

Providing and fixing rigid PVC bend (approved make ) for S.W.R. pipes including lubricating etc complete bend with door : 110mm

Providing and fixing rigid PVC bend (approved make ) for S.W.R. pipes including lubricating etc complete bend with door : 75 mm

Providing and fixing single Tee of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with door : 110mm

Providing and fixing single Tee of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with door : 75 mm

Providing and fixing R.P.V.C. vent cowl: 110mm

Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand) R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand ;4 graded stone aggregate 20mm nominal size foundation concrete 1:2:4 mix (1 cement ;2 coarse sand :4 graded stone agrregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cemetn and making channels in cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) neatly finished complete as per standard design. Inside size 90 x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455 x610mm internal dimensions total weight of cover ad frame to be not less than 38 kg. (weight of cover 23 kg. )

Providing and fixing square mouth S.W. Gully trap grade “A” complete with C.I. Grating brick masonry chamber and water tight C.I. Cover with frame of 300 x 300 mm size (Inside the weight of the cover to be not less than 4.53 kg.) And frame to be not less than 2.72 kg as per standard design:. 150 x 100 mm size P or S type

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer. Internal work - Exposed on wall. SCH-40(blue)/(white) 25mm outer dia.

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer. Internal work - Exposed on wall. SCH-40(blue)/(white) 32mm outer dia.

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer. Internal work - Exposed on wall. SCH-40(blue)/(white) 50mm outer dia

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer. External work.SCH-40(blue)/(white) 25mm outer dia.

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer. External work.SCH-40(blue)/(white) 50mm outer dia

Providing and fixing non-return valve of approved quality : 40 mm nominal bore

Providing and fixing ball valve ( brass ) of approved quality Low pressure with copper floats 25 mm nominal bore

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality : 20 mm nominal bore

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality : 25mm outer dia.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc 15 mm

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc 20 mm

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc25 mm

Providing at store or site work non-pressure RCC pipes of with collar joints conforming to IS:458-2003 revised as per amendment No.11 , including freight, carting, loading, unloading, stacking etc. complete 150 mm

Conveying carefully from stack at site, 250m from both sides rolling and lowering into trenches, laying and jointing true to line and level, RCC spun pressure and non pressure pipes of various classes, specials including collar and perfect linking of joint with jack to correct position including cost of jointing material in cement mortar 1:2, necessary hydraulic testing, curing of cement mortar etc. complete. 150 mm

Providing and fixing Angular Stop Cock with wall Flangue - Jaquar make. Florentine (FLR-5053N) 15mm of approved quality.

Providing and placing on terrace roof of floor two (1st flor roof single piece rotational moulded polythene water storage tank having I S I mark and conforming to I S 12701; 1996 1000 lit. capacity

Supply of inferential, dry dial, type Domestic Water Meter,suitable for horizontal installation, duly, sealed against tampering with couplings at both ends having pulse output facility compatable for automatic reading system ,conforming to IS:779-1974 and ISO 4064-2005 standards and bearing EEC/MID/OIML mark, (with latest Amendments)along with test certificate from FCRI/NABL as desired by the department.25 mm

Fixing water meter & stop cock in G. I. Pipe line including cutting & treading the pipe and making long screw etc. complete (cost of water meter and stop cock to be paid separately)

Providing and fixing brass bib cock (heavy) of approved quality : 15 mm nominal bore

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 including cutting of stone and making good the walls wherever required. Kitchen sink without drain board. with coupling & all accessories complete with choke stop strainer, Plain type having flat borders for correct sandwithing between the plaform top and bottom slabs complete. Overall size 610mmx510mm (24"x20") bowl size 545mmx445mmx200mm (211/2"x 17 1/2"x 8") depth 200 mm. Glossy. 1.0mm thk,

Providing and fixing NICKEL chrome plated copper alloy Fancy Pillar Cock with extended lever handle and wall flange Confirming to IS 8931; 1993 15mm nominal bore

ELECTRICAL WORKS

Supply, Installation, TESTING AND COMMISSIONING of 10 Mtr height Hot Dip Galvanized PU painted decorative step/tubular pole having top dia of 76 mm OD & base dia between 145mm to 175mm . Pole shall be mounted on square base plate ....mm thickness suitable for mounting on 4 nos foundation bolts. The Pole Shaft should be fabricated out of Steel tube of grade YST 240 and batch test reports for chemical and mechanical properties of material should be submitted along with the bid. Structurally designed base plate of Steel A36/A572-50 or equivalent should be welded with the pole shaft. The welding shall be of high quality, carried out by qualified welders using approved welding procedures and tested for its quality through NDT method, such as DP Test. The pole shall be provided with inbuilt Junction Box with an opening at the bottom with with proper gaskette & removable cover with proper gaskette along with provision of connectors, MCB, Wiring etc. A bracket suitable for mounting four Flood light fixtures must be provided for the application. The pole shaft structure and bracket shall be hot dip galvanized through single dip process as per ASTM A123 and minimum average coating shall not be less than 65 microns. No mechanical operation, such as welding, drilling, etc. should be carried out on the pole structure Complete pole shall be treated with high quality primer and thereafter coated with Polyurethane paint to minimum average DFT of 70 microns. The painting shall be carried out by experienced and trained technicians using proven and established painting procedure. Only ‘controlled’ paint drying process shall be used to ensure proper adhesion and finish of the paint. Make:- RR Ispat,Hakke ,Transrail, Mechanize Engineering. as required as directed by the Engineer In-charge.

Supply ,Installation,Testing & Commisioning of integrated LED flood light fitting Max. 200W IP65 & IK07 class having pressure die-cast aluminium housing, having system lumens output of Min. 10000 Lumens, min. efficacy of 100 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50, including driver & other related accessories .Make:- Havells,Reytek,Philips,Crompton,Leksa, La Luminaire, Wipro as required as directed by the Engineer In-charge.

Supply ,Installation,Testing & Commisioning of 4.5 m high galvanised Decorative conical Step pole with Decorative light bracket made from 40 mm. dia ‘B’ class G.I. Pipe, 0.6 to 1m. in length along with pole cap of 300mm / suitable length and 80 mm /Suitable dia.(Suitable to pole top) duly welded with provided leads, and with foundation bolts having bottom dia. from 105 to 141 mm, top dia. From 65 to 77 mm Complete with all required accessories like Junction box with 15A Input output connectors , 0.5 - 6 A C curve SP MCB for suitable for each light fittings 3 Core 2.5 Sq. mm Cu Flex. cable for light fitting from Junction box to Light fittings and its termination of cables should be made using with proper lugs ,Pole will Be Painted with P U Paint as per GTDC color choice .etc.Make-Havells, Reytek, Suncity, La lumiere, K lite as required as directed by the Engineer In-charge.

Supply,installation,testing,commisioning of 40W decorative luminaire made of spun aluminium body with pressure die-cast heat management (PDCHM) and the IP65 optical compartment with high power LED/s is comprised of a deep drawn chemically polished and co-extruded, thermoformed polycarbonate protector stabilized agent UV rays suitable for 40W LED. Fitting should be suspended mounting type fixture. System Wattage:40W LED, Protection class:IP65, Driver Integral: Constant Current, Input Voltage: 230-240 Vac, Frequency: 50-60Hz, Operating Voltage:120- 277Vac, Operating Temperature: 0deg to +50deg C, single phase ac supply. LED Lumens: @120lm/w 4800lm, CRI(Ra):>80, LED Colour Temperature: 3000 to 5700K, Life Span:>59,000 Hours,, Physical Body: Die cast Aluminium Base, Body Spun Aluminium, Diffuser: Convex Type Translucent / V Translucent Polycarbonate glass, Mounting: Suitable for 48mm OD Pipe, Finish: Powder Coated Black, Driver Power Factor:>0.95, THD:<7.8%,Surge Protection: 4KV, Efficiency:>87%. Fitting should have inbuilt driver with efficiency >0.9 and having surge protection device of 4KV and external surge protection device of 10KV. IP65 and LM79-2019 report to be provided. Make: Havells, Reytek, Suncity, La luminie, K- lite as required as directed by the Engineer In-charge.

Supply,installation,testing,commisioning of Architectural Pole of 6mtr Height Single arm made of galvanised iron sections of 140mm & 76mm dia. Wind speed considered in design 50m/s, IS 875: PART - 3 :1987 .Material for tubes steel of grade YST 210. Material for base plate steel of grade E250 to IS 2062 ; 2011. The Bracket will be provided with reducer/expander for holding the suspended type fixture on to the main pole with all arrangements having position perpendicular to the ground. The bracket shall be single arm on 6mtr with a span of 1000mm. The bracket top shall be covered with FRP cap to enclose the pipe. The Pole will be placed with a Aluminium embellishments on the bottom & Middle section for aesthetic & Decorative purpose. The pole will be provided with an inbuilt IP 65/66 junction box to fix 32Amp Connectors & 6Amp MCB inside the cut window of the bottom pipe the in built box should have a flush door of suitable size. The Decorative pole will be mounted on a square base plate of size 250 X 250mm having 12mm thickness. The mounting steel plate along with hot dip galvanised foundation bolts of size M16 X 600mm to be used for ensuring firm grouting in the specially designed /Provided RCC foundation. The Galvanised pole should be painted in 3 layer coating (Coating thickness should be more than 50 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy zinc primer & 3rd final layer with PU Paint of Matt Black on Pole and Golden on Aluminium Embellishment or as per GTDC .Make-Havells, Reytek, Suncity, La luminie as required as directed by the Engineer In-charge.

Supply,installation,testing,commisioning of Architectural Pole of 6mtr Height Double arm made of galvanised iron sections of 140mm & 76mm dia.. Wind speed considered in design 50m/s, IS 875: PART - 3 :1987 .Material for tubes steel of grade YST 210. Material for base plate steel of grade E250 to IS 2062 ; 2011. The Bracket will be provided with reducer/expander for holding the suspended type fixture on to the main pole with all arrangements having position perpendicular to the ground. The bracket shall be double arm on 6mtr with a span of 1000mm. The bracket top shall be covered with FRP cap to enclose the pipe. The Pole will be placed with a Aluminium embellishments on the bottom & Middle section for aesthetic & Decorative purpose. The pole will be provided with an inbuilt IP65/66 junction box to fix 32Amp Connectors & 6Amp MCB inside the cut window of the bottom pipe the in built box should have a flush door of suitable size. The Decorative pole will be mounted on a square base plate of size 250 X 250mm having 12mm thickness. The mounting steel plate along with hot dip galvanised foundation bolts of size M16 X 600mm to be used for ensuring firm grouting in the specially designed/Provided RCC foundation. The Galvanised pole should be painted in 3 layer coating (Coating thickness should be more than 65 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy zinc primer & 3rd final layer with PU Paint of Matt Black on Pole and Golden on Aluminium Embellishment or as per GTDC.Make-Havells, Reytek, Suncity, La luminie, Klite as required as directed by the Engineer In-charge.

Supply,installation,testing,commisioning of 70W decorative luminaire made of spun aluminium body with pressure die-cast heat management (PDCHM) and the IP65 optical compartment with high power LED/s is comprised of a deep drawn chemically polished and co-extruded, thermoformed polycarbonate protector stabilized agent UV rays suitable for 70W LED. Fitting should be suspended mounting type fixture. System Wattage:70W LED, Protection class:IP65, Driver Integral: Constant Current, Input Voltage: 230-240 Vac, Frequency: 50-60Hz, Operating Voltage:120- 277Vac, Operating Temperature: 0deg to +50deg C, single phase ac supply. LED Lumens: @120lm/w 8400lm, CRI(Ra):>80, LED Colour Temperature: 3000K, Life Span:>59,000 Hours,, Physical Body: Die cast Aluminium Base, Body Spun Aluminium, Diffuser: Convex Type Translucent / V Translucent Polycarbonate glass, Mounting: Suitable for 48mm OD Pipe, Finish: Powder Coated Black, Driver Power Factor:>0.95, THD:<7.8%,Surge Protection: 4KV, Efficiency:>87%. Fitting should have inbuilt driver with efficiency >0.9 and having surge protection device of 4KV and external surge protection device of 10KV. IP65 and LM79-2019 report to be provided. Make: Havells, Reytek, Suncity, La luminie as required as directed by the Engineer In-charge.

Supply ,Installation,Testing & Commisioning of of Concealed type Step Light with 6W LED lamp Die-cast aluminium housing having system lumens output of Min. 500 Lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 5000K, Beam Angle of 110 deg., THD<10%, SDCM<5, p.f. >0.95, operating range of 230-270V, surge protection of 2.5 kV, Life class of 25,000 Hrs. at L70B50, including driver by making necessary arrangement/recess in wall to make it flush with surface ,IP Rating : IP 67 ,IK10 rated , connecting wire, including gear box and junction box for cable connection Complete and Coated with epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint .Make:- Havells,Reytek,Philips,Crompton,Leksa, La Luminaire, Wipro, Klite,Jaquar. as required as directed by the Engineer In-charge.

Supply ,Installation,Testing & Commisioning of LED Strip light Max. 45 W IP67 class having minimum lumens output of 800 Lumens/m, min. efficacy of 90 lumen/W, CRI>80, CCT upto 5000K, Beam Angle of 110 deg., THD0.95, operating range of 230-270V, Life class of 30,000 Hrs at L70B50 including driver accessories complete.Make:- Havells,Reytek,Philips,Crompton,Leksa, La Luminaire, Wipro, klite . as required as directed by the Engineer In-charge.

Supply ,Installation,Testing & Commisioning of Tree Uplighter with Spike,9W LED lamp complete with IP66, 24VDC, Suitable watts driver / power supply (if any), connecting wire,.Complete with all accessories and Coated with epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint .Make:- Havells,Reytek,Philips,Crompton,Leksa, La Luminaire, Wipro, Klite. as required as directed by the Engineer In-charge.

Supply ,Installation,Testing & Commisioning of integrated LED flood light fitting Max. 70W IP65 & IK07 class having pressure die-cast aluminium housing, having system lumens output of Min. 8400 Lumens, min. efficacy of 120 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50, including driver with U shaped bracket & other related accessories .Make:- Havells,Reytek,Philips,Crompton,Leksa, La Luminaire, Wipro, Atilite, Nice. as required as directed by the Engineer In-charge.

Supply ,Installation,Testing & Commisioning of Bulk Head LED fitting Max. 10-12W with high transitivity diffuser with system lumens output of Min. 1100 lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., THD0.95, operating range of 140-260V, in built surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B50, IP66, IK09 rated including driver IP66, IK09 rated on provided PVC Block / wooden board with accessories complete.Make:- Havells,Philips,Crompton,Leksa, Wipro as required as directed by the Engineer In-charge.

Supply of 3 core unarmoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 Core 2.5 sq.mm

Supply of 3 core unarmoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 Core 4 sq.mm

Supply of 3 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 Core 4 sq.mm

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 4 Core 4 sq.mm

Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 1/2 Core 35 sq.mm

Supply of 3 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 Core 16 sq.mm

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 4 Core 16 sq.mm

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm in the existing RCC/HUME/STONEWARE Metal pipe, etc. complete as required

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. a) In soily strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. (a) In soily strata

Laying of one number additional PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground in the same trench in one tier horizontal formation including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. a) In soily strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm on surface, etc. complete as required

Construction of manhole rectangular in shape including cement concrete 1:3:6 (1 cement:3 coarse sand:6 graded stone aggregate 20mm nominal size) foundation thickness of concrete 20cms and offset 10cms on both sides and first class brick work with bricks class designation 100kg/sq.cm (wire cut bricks) cement mortar 1:3 (1 cement : 3 coarse sand) 23cms thick including providing & fixing CI footrests confirming to IS 5445/69 or revised and whose weight shall not be less than 5.30kgs including fixing in man-hole at 30cm c / c in 20x 20x10cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) and 12mm thick plaster inside and outside with cement mortar 1:3 (1 cement : 3 coarse sand) including adding waterproofing compound of approved brand in cement mortar with a floating coat of neat cement and making channel in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20m nominal size) neatly finished complete as per standard design. III) Inside size 0.60x0.60m and 0.60m deep (with medium duty DI manhole cover & frame of size 0.60x 0.60m weighing 90kgs ) including fixing with cement concrete 1:2:4 ( 1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size and applying the frame & cover with coal tar.(Refer Quantity in drawings)

Providing at store or site work non-pressure RCC pipes of with collar joints conforming to IS:458-2003 revised as per amendment No.11 , including freight, carting, loading, unloading, stacking etc. complete. c) 150 mm Dia.NP2 Class

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 3 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 3 x 1.5/2.5 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 3 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 3 x 4 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 4 x 4 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 3 1/2 x 35 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 3 x 16 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 4 x 16 Sq. mm.

Supply, installation, testing and commissioning of electronic type three phase energy meter (KWh), 4 wire, ISI marked, in polycarbonate or sgheet steel body ( base mounting type) with counter display/LCD display, with ELT, in Class 1.0, 50 Hz, 240 V. AC duly tested by MRT along with Test Certificates, complete as required of following capacity of make L & T only. (b) 10 to 40 A

Supply of 6 KVA 3 Phase Unbalanced fan air cooled Static voltage stabilizer with technology of DSP Based IGBT PWM Switching,Input voltage range (V L-L) =320-480 ,Output voltage (V L-L) =400 V ,Output Voltage Regulation = 1% of nominal output voltage,Automatics High & low Voltage cut off input and out put voltage Circuit protections, single phasing preventer/Phase reversal protection,over load & Short circuit protection(Use MCB),Independent Phase Control,LCD /LED Display for regulations mode ,Bypass mode & fault conditions,Automatic bypass: A Fault conditions,Protection Class : IP 20 ,Ambient Temperature : 0 to 45 Degree Celsius ,Wave form Distortion:pure sine wave.

Supplying and fixing following way SPN sheet steel MCB distribution board Consumer Unit 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar hinged front acrylic cover for the MCB knobs detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator) (b) 2 + 8 way Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. a) SP, Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. b) DP, Cat A

Supplying and fixing following rating double pole (single pole and neutral) 240 V RCCB having a sensitivity current upto 300mA in the existing MCB DB complete with connections testing and commissioning etc as required (a) 25 A, Cat A

Supplying and fixing 63 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. TPN, Cat B

Supplying and fixing following rating four pole (triple pole and neutral) 415 V RCCB having a sensitivity current upto 300mA in the existing MCB DB complete with connections testing and commissioning etc as required (c) 63 A, Cat A

Supplying and fixing SP blanking plate in the existing MCB DB complete as required.

Supply , Installation , Testing and Commissioning of Cable Junction Boxes IP 66/67 “weather proof”(Size -155 x 210 x 92 (LXBXH)mm + Cable termination upto 16 Sqmm size.), for outdoor installation(with knockouts for cable entry) with all accessories. Make: Hensel ,Neptune as required as directed by the Engineer In-charge

Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI mark, of approved brands including accessories and providing masonry enclosure with CI/RCC cover having locking /Lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size not less than 1.0x1.0x 2.0 mtrs(min) and disposal of excavated soil. b) Class B GI pipe, 40mm diameter as per specifications. c) Charcoal/salt as per specs ( paid seperately). d) Refilling the pit of size not less than 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe . g)watering arrangement (b) In rocky strata

Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosure with CI/RCC cover having locking/Lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 3.0 mtrs(min) and disposal of excavated soil. c)Watering GI pipe, 20mm, Class B, with funnel as per specs. d) Charcoal/salt as per specs ( paid seperately). e) Refilling the pit of size 1.0x1.0x 3.0 mtrs(min) with soft black agriculture soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe.g)watering arrangement(plumbing will be paid seperately). b)In rocky strata

Extra for using salt and charcoal for pipe earth electrode as required( 65 Kgs of Charcoal and 5 Kgs of Salt).

Supplying and laying 25 mm x 6 mm GI strip at 0.5 m below ground as strip earth electrode including soldering etc. as required

Providing and fixing 25 mm x 5 mm GI strip on surface or in recess for coneections etc. as required

Supplying and laying 6 SWG GI wire at 0.5 m below ground level for conductor earth electrode including soldering etc. as required

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) with modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. a) Group B -- with Cat A Modular Accessories

Wiring for group controlled light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable (with)in recessed PVC conduit(heavy) and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the (with) independent recessed PVC conduit(heavy) of appropriate size as required. b) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the (with) independent recessed PVC conduit(heavy) of appropriate size as required. (c) 2 x 4 sq.mm + 1 x 4 sq.mm earthwire (20mm Conduit)

Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required. b) 25 mm

Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required. (c) 32 mm(Ground to DB)

Supplying and fixing following modular switch/ socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required (a) 5/6 A switch Cat A

Supplying and fixing following modular switch/ socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required (d) 3 pin 5/6 A socket outlet Cat A

Supplying and fixing following modular switch/ socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required b) 15/16 A switch Cat A

Supplying and fixing following modular switch/ socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required d) 6 pin 15/16 A socket outlet Cat A

Supplying and fixing modular blanking plate on the existing modular plate switch box excluding modular plate etc. as required a) Cat A

Supplying and fixing following size modular GI box alongwith modular base and cover plate for modulator switches in recess etc. as required b) 4 Module ( 125 mm x 7 mm) Cat A

Supplying and fixing following size modular GI box alongwith modular base and cover plate for modulator switches in recess etc. as required (c) 6 Module (200mm x 75 mm) Cat A

Supplying & erecting of LED 9 to 10W tube light fitting (2 feet) with PC housing, heat sink, integrated HF electronic driver complete. Make: Philips, Reytek, Leska, Crompton, Wipro, Havells as required as directed by the Engineer In-charge

Supplying & erecting of LED 20W tube light fitting (4 feet) with aluminium housing, heat sink, integrated HF electronic driver complete.(Includes suspension accessories). Make: Philips, Reytek, Leska, Crompton, Wipro, Havells as required as directed by the Engineer In-charge

SITC of Well glass light fitting,36W IP66 & IK07 class ,surface or suspended mounting pressure die-cast aluminium housing , min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, THD<10%, p.f. >0.95, operating range of 140-270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs at L70B50 including driver with U shaped bracket,Beam angle -125 deg.complete with all accessories.

Supply and erecting of 12 inch (300 mm sweep) exhaust fan with double ball bearings, 1400 rpm, complete with all accessories. (a) Cat A

Supply and erecting of 48 inch ( 1200mm sweep) ceiling fan, double ball bearing type, , complete with all accessories. (b) Cat B

Supply and erecting fan hook box ( 100 mm diameter or equivalent square size, 75mm deep) fabricated out of 16 SWG sheet steel with 10 m round bar hook bounded to RCC steel upto 50 mm length protruding on each side of the box, including painting with 2 coats of red oxide, complete as required.

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required (a) Cat A

GI Pipe Medium Class 25 mm (Civil GSR 1034 (f)(iii))

BAGKIYA CONSTRUCTIONS PVT LTD (BID ID -51560)