Constrcution of Car Parking below proposed community centre Tutikandi II in ward No 10 under AMRUT

Amount

Excavation in foundations, trenches etc., in earth work, lift upto 1.50 Metres stacking the excavated soil not more than 3 metres clear from the edge of the excavation and then returning the stacked soil in 15cm. layers, when required in to plinths sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed with in a lead of 20 metres.

Excavation in earth work and filling in 15 cm. layers in foundation and plinths including ramming, watering and consolidating upto a lead of 20 metres and lift upto a 1.5 metres. Pick Work.

Disposal of materials (earth work) by mechanical transport including loading and unloading and stacking upto 10 km (disposal of earth at approved MC dumping site)

Providing from work with steel plates 3.15 mm thick welded with angle iron in frame 30*30*5mm so as to give a fair finish including centring , shuttering and propping etc.with wooden battens height of propping and centring below supporting floor to ceiling upto all heights and removal of the same for insitu -reinforced concreate & plain concreate work in:-. Foundation , footing basis of coulmn etc. and mass concrete.

Flat surfaces such as soffits of suspended floors, roofs ,landings and the like Floor etc. up to 200 mm in thickness

Coulmn , pillars , post and struts:-Circular or curved in plan

Beams , cantilever , grinders and lintels:-Sides and soffits of beams beam haunching cantilevers , brssumers and lintels not exceeding 1 metre in depth in all heights from floor

Stair case with sloping or stepped soffits including risers & stringers excluding landing.

Providing and laying cement concrete 1:4:8 (1 cement: 4 sand: 8 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of centring and shuttering in foundation and plinth with in all leads , lifts of materials and other incidentals.

Providing and laying cement concrete 1:1:2 (1 cement : 1 sand :2 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement in reinforced concrete work in :Foundation And Plinth

Suspended floors roofs, landing and shelves and their supports , balconies, beams, griders, bressumers and cantilivers upto floor two level.

Lintels, beams girders bressumers and cantilevers up to floor two level :

Column, pillars, posts and struts upto floor two level :

Stair cases (except spiral cases) excluding landing,but preparing of the the surface & finishing of nosing upto floor two level.

Providing mild steel/Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete up to floor two level:

Brick work using common burnt clay building bricks in in Superstructure above plinth level upto floor two level : Cement mortar 1:6 (1 cement : 6 sand) Second Class Bricks

Half brick masonary in common burnt clay building bricks :- in cement mortar 1:4

Cement concrete flooring 1:2:4 laid in one layer finished with a floting coat of neat cement including carriage of materials withinn all leads and lifts.40 mm thick

6mm Cement plaster to ceiling In Cement mortar 1:3(1 Cement:3 Sand)

15mm thick cement plasters in single coat on fair side of brick/concrete /stone walls for interior plastering up to all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm in grith and finished even and smooth with cement morter 1:6 (1 cement:6 sand).

15mm thick cement plasters in single coat on rough side of brick/concrete /stone walls for exterior plastering up to all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm in grith and finished even and smooth in cement morter 1:6 (1 cement:6 sand).

White washing with lime on ceiling and /or sloping roofs and undecorated wall surface in all floors two coats to give an even shade including thoroughly brooming the surface to remove all dirt , dust morter dust and other foreign matter including carriage of materials within all leads and lifts.

Distempering with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surface on all floor to give an even shade over and including priming coat of whiting after thoroughly brushing the surface free from morter dropping and other foreign material including preparing the surface even and sand papered smooth including carriage of materials within all leads and lifts:-

Applying white cement based wall care putty over plaster surface after thoroughly brushing the surface free from morter drops , dust , loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

P/F M.S Pipe 40mm nominal bore for railing & fixed in M.S Angle /Channels.

Providing woodwork in frames of doors, windows, clerestory,windows and other frames wrought,framed and fixed in position. 2nd class deodar wood.

Providing and fixing panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws. 50 mm thick 2nd class deodar wood.

Providing and fixing vitreous China wash down, water closet (Europeon type.W.C pan) with integral 'p' or 's' trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement :1 Sand )(seat and over to be measured and paid for separately)

Providing and fixing 12.5 liters vitreous china low level flushing cistern with a pair of C.I or mild steel brackets ,complete with fiiting such as lead valve less syphon,15 mm nominal size brass ball valve with polythene float , C.P brass handle ,unions and coupling for connections with inlet,outlet and overflow pipes,40 mm dia C.P flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe is to be measured and paid separately)

Providing and fixing C.P. Brass bib tap superior or heavy type 15 mm dia

Providing and fixing vitreous china squatting plate pattern Urinal of size 450mmx350mm with intergral flush pipe

Providing 32mm dia PVC waste pipe for wash basin or sink

Providing and fixing 600x450mm bevelled edge mirror of superior glass marked on 6mm thick AC sheet or plywood sheet and fixed to wooden plug with brass screws and washer

Providing and fixing CP brass towel rail complete with CP brass bracket fixed to wooden plug with CP brass Chrome plate)

Providing and fixing CP brass soap dish with CP brass bracket fixed to wooden cleats with brass screws chrome plate

Providing and fixing plastic seat (solid and hollow type) cover for wash down water closet with C.P Brass hinges and rubber buffers white plastic seat and cover

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I or M.S brackets painted white including cutting holes and making good the same but excluding fittings

Providing and fixing to wall ,ceiling and floor galvanised mild steel tubes (medium grade) tube fitting and clamps including making good the wall, ceiling and floor (15 mm nominal bore)

Electrical Lumpsum:-Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit with modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. Group C.

Wiring for twin control light point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit, with 2-way modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required.Group C.

Wiring for power plug with 2x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Wiring for power plug with 4x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required. 2x1.5 Sq. mm.

Supplying and fixing of following sizes of PVC conduit along with the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required:- 20 mm. Dia

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 5 pin 5/6 amps modular socket outlet and 5/6 amps, modular switch, connections etc. as required.

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps, modular switch, connections etc. as required.

Supplying and fixing ceiling rose on the existing junction box / wooden block including connections etc. as required.

Supplying and fixing brass batten/angle holder including connections etc. as required:-

Supplying and erection of wall mounted metal boards for switch gear mounting of suitable size, with permissible variation in size of plus minus 5mm, welded frame work made of M.S. angle iron (35 mm x 35 mm x 6 mm thick) with sufficient numbers of horizontal and vertical intermediate members (25mm x 6mm thick) flat iron including painting and bonding to the existing earth as required:-

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required:- Single pole. Cat-A.

Supplying and erection of 40/50/63 amps rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required:- Double pole. Cat-A.

Supplying and fixing single pole, blanking plate in the existing MCB DB complete as required.

Earthing with copper earth plate 600 mmx600 mmx 3 mm thick, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.

Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required.

Providing, laying and fixing of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade on surface etc. of the required size:-Armoured cable 50 sq. mm (3.5 core)

Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required:-Exhaust Fan, Heavy duty, 300 mm sweep

P/F LED street light with pressure die cast housing with toughened glass and individual LEDs with secondary optics and IP66 protection of Bajaj make of 60w with code BRTFG 60w LED V3 including making connection, testing etc. as required at site

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required. 2x10 Sq. mm.

Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface/recess, completewith tinned copper bus-bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:- Double door-6 way

Supplying and fixing of bulk head fitting of all sizes and shapes, containing one No. thread type CFL lamp holder (s), complete with all accessories but excluding CFL lamp including making connections, testing etc. as required Bulk head fitting, CFL type (Category-A)

SUNIL SHARMA

BHARAT SINGH CHAUHAN

Ashu Chauhan

Sajad Ahmed

CHANDAN KUMAR

Suresh Vekta

Sunil Khachi

Arun Hetta