REPAIR TO FENCING, DRAIN, PATH AND SECURITY WALL, REPAIR/REPLACEMENT AND CLEANING OF SEWAGE LINES, SEPTIC TANKS

Amount

Demolition of PCC (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L PCC (1:2:4) type B1 (using 20mm graded crushed stone aggregates) as in surface channel and drains etc, finishing surface even and smooth without using extra cement including necessary formwork complete all as specified and as directed.

M&L for extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

Add or deduct to the item no. 3 above for each 25mm girth or part thereof over or under 30cm complete all as specified and directed

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate ) as in path , plinth protection , sub floor etc finishes concrete surface fair & even including necessary formwork etc complete all as specified and directed.

M&L for 100mm thick PCC (1:2:4) type B2 (using 40 mm graded stone aggregates), finished cement concrete even and smooth without using extra cement and spike rolling to surface or making impression of expanded metal whilst the concrete is green etc complete all as specified and as directed.

M&L for forming construction joint 75mm deep x 10mm wide filled with sealing compound Grade-A complete all as specified and directed.

M&L for machine pressed pre polished factory made pavement chequered cement concrete tiles of size 300 X 300 X 20 mm thick of approved design and colour , set jointed and pointed in neat cement slurry with grey cement and pigment over and including 15 mm thick screed bed in cement sand mortar (1:4) complete all as specified and as directed.

M&L for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in parapets, coping, benching, appex stone etc water trough and the like etc including necessary formwork complete as specified and directed.

Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion, embedded in concrete and making good disturbed ground complete all as specified and directed.

Excavation in post holes each n.exc. 0.5 cum in soft/loose soil getting out returning, filling in and ramming earth or broken rubble mixed with earth around in layer n.exc. 25 cm, watering and removing surplus soil to a distance n.exc. 50 mtr and making good surface complete all as specified and directed.

M&L for PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in sub base of floor , foundation filling and mass concrete including necessary form work etc complete all as specified and directed by Engineer in Charge.

S&F MS screw bolt (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc. 5 cm and n. exc 10 cm long, diameter of neck 5 to 10 mm complete all as specified and directed.

Dismantling fencing wire mesh including taking out of fixing arrangement like flat iron bars & round steel bars any type complete all as specified and directed.

Supply only Chain link MS galvanised fencing, any size or type etc complete all as specified and as directed.Note:- (The unit weight of chain link shall not be less than 4 kg per sqm).

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of new GI binding wire etc complete all as specified and as directed.

S&F in repair Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

S&F mild steel angle iron or other sections for post and struts in fencing, flat iron fillets (for securing wire mesh etc) to fencing post, cut to shape, drilled and countersunk for screw, including cutting tops to shape as directed, drilling holes, notching for wire, embedding in concrete and screwing etc. conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for mild steel round bar upto & including 10 mm dia cut to length bent to shape required including bending, hookings as in chain link fencing fixed with bent to shape required including bending, hookings as in chain link fencing fixed with nut &bolt or securing with clips quality conforming to Fe-410-S etc complete all as specified and as directed.

Fixing only angle iron mild steel post and flat iron fillets in fencing including necessary cutting, drilling, welding etc. complete all as specified and directed

M&L for prepration of new steel surface of any description over 10cm in width or girth and applying two coat of synthetic enamel paint over one coat of red oxide/ zinc chrome primer complete all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth and getting out in soft/ loose soil for foundation etc. complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n. exc. 25cm in soft/loose soil complete all as specified and directed.

Removing excavated soils to a distance n. exc. 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed.

Demolition and breaking up drain pipes 150 mm bore (Salt glazed ware, AC or Reinforced concrete) set in cement mortar including taking out of trenches complete all as specified and directed.

Demolition and breaking up drain pipes 100 mm bore (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes 100/75 mm, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

S&F High density polyethylene pipes (HDPE) 160mm dia of pressure rating 6 kgf/cm2 laid in trenches etc complete all as specified and as directed.

M&L for PCC (1:3:6) type C2 as in Concrete bed to150 mm drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested complete all as specified and as directed.

S&F High density polyethylene pipes (HDPE) 110mm dia of pressure rating 6 kgf/cm2 laid in trenches with & including bends,as required etc complete all as specified and as directed.

M&L for PCC (1:3:6) type C2 as in Concrete bed to100mm drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested complete all as specified and as directed.

S&F in repair PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints fixed to walls/ floor complete including clamps for securing pipe complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints fixed to walls/ floor complete including clamps for securing pipe complete all as specified and directed.

S&F in repair PVC (SWR) 110mm dia branch piece, (Single Y) equal or unequal complete all as specified and as directed.

S&F in repair PVC (SWR) 110mm dia branch piece with access door, (Single Y) equal or unequal complete all as specified and as directed.

S&F in repairs PVC (SWR) bend of any radius 110mm bore complete all as specified and as directed.

S&F in repairs PVC (SWR) bend with access door of any radius 110mm bore complete all as specified and as directed.

S&F in repairs PVC (SWR) bend of any radius 75mm bore complete all as specified and as directed.

S&F in repair PVC (SWR) 110mm dia in junction single with access door, (Single T) equal or unequal complete all as specified and as directed.

S&F in repair PVC (SWR) 75mm dia in junction single with access door, (Single T) equal or unequal complete all as specified and as directed.

S&F in repair PVC (SWR) vent cowl 110mm dia complete all as specified and as directed.

S&F in repair PVC (SWR) vent cowl 75mm dia complete all as specified and as directed.

S&F in repair PVC (SWR) reducer 110mm dia complete all as specified and as directed.

S&F stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm dia pipe complete all as specified and as directed

All as per item no. 44 above but for 75 mm dia pipe complete all as specified and as directed

Cleaning of SWG Pipe 100/150/200 mm internal dia of depth upto 1 m by rodding or by using pressure pump completely including man holes and removal of sludge to a distance exc 1.5 Km and n.exc 5 Km out side of MOD land complete all as specified & directed by Engineer-in-Charge.

Dewatering and taking out / removal of sludge waste / foreign materials from Septic Tanks and soakage wells using mechanical pump and disposal of raw water/effluent.sludge/waste/foreign materials by burying under ground borrow pit of suitable size and covering the pit with earth or earth mixed rubbish with spreading bleeching powder @ 1 kg per pit for disinfection purpose and removing surplus soil to a distance exc1.5km but not exc 5 Km out side of MOD land complete all as directed by Engineer-in-charge. NOTE : Cost of earthwork in excavation for earth pit and spreading of bleaching powder shall deemed to be included in the unit rate quoted by the tender against these item.

Cleaning of Manholes depth n. exc 1.50 metre each, with spades or bucket, taking out sludge from manhole and disposed off aside by burying the entire sludge under ground in a earth pit dug of suitable size by putting earth mixed with rubbish in it and spreading bleaching powder surrounding the pit and again using water with bucket and put into manhole to clear the sludge and ensure the sludge is drain out completely etc complete all as specified and as directed by Engr-In-Charge. Note :- Cost of earthwork in excavation for digging the pit , returning, filling or covering the same with soil and removing surplus soil to a distance n.exc 50m from the starting point & spreading of bleaching powder around and over the pit shall be deemed to be included in the rate quoted.

Cleaning of CI/RCC/PVC pipes of any dia from first floor to ground floor up to trap and 1st manhole along the wall, floor, including rodding and removing waste material to a distance not exc 50 mtr all as directed.

M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-l smooth finished, and reforming benching as required for 100 mm internal dia of pipe complete all as specified and as directed

M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-l smooth finished, and reforming benching as required for 150 mm internal dia of pipe complete all as specified and as directed

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for precast RCC (1:2:4) type B1 (using 20mm graded stone aggregate) as in cover slabs, shelves and similar articles set in CM (1:6) including necessary form work complete all as specified and directed.

M&L for RCC (nominal mix) (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, deck slabs and in shelves etc complete all as specified and directed.

M&L for form work to sides and soffits of suspended slab such as roof slabs, deck slabs and similar work, vertical or to batter, n. exc. 200 mm thick, rough finished flat surfaces complete all as specified and directed.

M&L for Mild steel TMT deformed bars, 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, precast cement concrete block walling in any position, built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L for Block masonry with solid precast cement concrete blocks made out of cement concrete (1:3:6) type C1, using 20 mm graded stone aggregate, exc 10 Cm width and setting in cement sand mortar 1:6 complete all as specified and directed.

Taking down cement plaster including racking out joints, hacking for key scrubbing down with water etc including removal of rubbish material from site complete all as specified and as directed.

M&L for Rendering 10mm thick plaster on fair faces of brick work or concrete surfaces in cement sand mortar (1:4) finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

M&L for Non-skid ceramic colour tiles 7 to 8 mm thick , joint free , (square/rectangular), area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:4 ,set and jointed in neat cement slurry and pointed in white / coloured cement to match complete all as specified and directed by Engineer-in-Charge.

M&L for Glazed ceramic colour tiles of size 300x200x7/450 x 300 x 7mm thick in vertical surfaces of wall such as skirting , dado, riser etc set and jointed with neat cement slurry and pointed in white or colour cement to match with the colour of tile over and including 10 mm thick backing course in cement sand mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for Granite (of any type) tiles 18-20 mm thick machine cut , bedded and jointed with grey cement and pointed with white cement with admixtures over and including 20 mm thick screed bed in cement sand mortar 1:4 complete all as spefied & directed

Dismantling wall and ceilling boards of any description including cover fillets complete all as specified and directed

M&L for 4mm thick non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with nails as in ceiling complete all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section unframed work in any position complete all as specified and directed.

M&L 2nd class hard wood in scantling, clean sawn, timber fixed with nails complete all as specified and directed.

Dismantling timber fillets, rails, posts rafter purlins, etc., under 40 Sqcm in sectional area complete all as specified and directed

M&L 2nd class hard wood plain fillets, square, rectangular or triangular in section, clean sawn secured with nails or brads of sectional area exc. 13 & n. exc. 25 Sqcm complete all as specified and directed.

M&L for 2nd class hard wood plain fillets bullnosed, splayed, chamfered or rounded on one edge or face in section clean sawn, fixed with screws sec are exc. 6 & n. exc. 13 sqcm complete all as specified and directed

Dismantling boarding any description fixed in any position with nails complete all as specified and directed

S&F 2nd class hard wood boarding 20mm thick fixed with nails as in eaves board planed one side with butt joint complete all as specified and directed

S&F block board 18/19mm thick, grade 2 quality, interior grade, commercial type, with external teak wood lipping 6mm thick fixed with screws to timber frame work complete all as specified and directed

M&L for preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats creosote oil complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description n. exc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

M&L for Rendering, 15 mm thick plaster in cement sand mortar ( 1:4), in two layers, top 5 mm thick with approved liquid Water proofing compound @ 3% by the weight of cement or as per manufacturers instructions over a layer of 10 mm thick base coat including finishing the surface even and fair, complete all as specified and as directed by Engineer-in-Charge. Note WPC shall be measured and paid separately.

M&L for Rendering 10mm thick plaster on fair faces of brick work or concrete surfaces in cement sand mortar (1:6) finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L for 5mm thick plaster in CM (1:3) on fair faces of concrete surfaces of ceiling including finishing even & smooth without using extra cement.

Supply only for water proofing compound.

M&L for preparation of new plastered surface of walls and applying two coats of acrylic distemper over a coat of alkali resistant priming paint complete all as specified and directed.

M&L for preparation of new plastered surface of walls and applying two coat of white or tinned with cement base paint over priming coat complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new ceiling surfaces and applying three coats of white wash complete all as specified and directed.

S&F 2 to 3 mm thick PVC sheet of size 25x20 cm fixed/pasted on one side of writing letter or figure over the sheet for identification/marking of bldg no. fixed on wall with cadmium screws and washers complete all as specified and directed.

Taking down chowkats or frames n. exc. 1.5 Sqm each (without taking off shutters from the frame) and removing from site complete all as specified and directed.

Taking down chowkats or frames exc. 1.5 Sqm but n. exc. 4 Sqm each (without taking off shutters from the frame) and removing from site complete all as specified and directed.

Taking down shutters of any description n. exc. 1 Sqm each and removing from site complete all as specified and directed.

Taking down shutters of any description exc. 1 Sqm and n. exc. 2 Sqm each and removing from site complete all as specified and directed.

Taking down shutters of any description exc. 1 Sqm and n. exc. 2 Sqm each and refixing in same opening complete all as specified and directed.

M&L for 2nd class hard wood as in plain, solid, straight chowkats & frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

M&L for 35 mm thick factory made flush shutters, solid core construction, with block board core and plywood face, pannels, commercial type on both sides including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed.

M&L 35mm thick 2nd class hard wood factory made glazed and skeleton shutter, open rebated and prepared to receive glass, gauge etc. without sash bar edges of framing moulded, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(a) complete all as specified and directed.

M&L 30mm thick 2nd class hard wood factory made glazed and skeleton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) complete all as specified and directed.

M&L 30mm thick 2nd class hard wood factory made glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. without sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) complete all as specified and directed.

S&F factory made pre laminated solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with single piece extruded pvc profile both side prelam PVC sheet 'C' channel having a 5mm thick PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and 5mm thick both side prelam single piece extruded pvc profile for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of both side prelam 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and shown on drawing given in SSR Part II. The width of stiles & rails shall be in proportion to the width of the door shutter as given in SSR Part I complete all as specified and directed

S&F pre laminated solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam single piece extruded pvc profile and edgs will be painted to match with prelam sheet , PVC sheet are to be reinforced with 19x19mm MS square tube EPDM rubber gasket weather seal shall be provided through out the frame. The profile shall be mitre cut at two corners and joint by insrting 2 nos of 150mm long backets of 15mmx15mm MS square tube inside the 19mmx19mm MS square tube and suitably screwed and fixing in opening as per specification & drawing complete all as specified and directed.

S&F mild steel butt hinges, medium weight 100 mm size ISI marked complete all as specified and directed.

S&F mild steel butt hinges size 75 mm, ISI marked, medium weight, cold rolled complete all as specified and directed.

S&F 100 mm size cadmium plated stainless steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws/welded to frame complete all as specified and directed.

S&F 150 mm long, anodised aluminium, barrel tower bolts of extruded section ISI marked complete all as specified and directed.

S&F 125 mm long, anodised aluminium, barrel tower bolts of extruded section ISI marked complete all as specified and directed.

S&F 150mm size anodised aluminium handles, cast type, ISI marked complete all as specified and directed.

S&F 125mm size anodised aluminium handles, cast type, ISI marked complete all as specified and directed.

S&F 300mm long MS sliding door bolts ISI marked bolt type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed

S&F 300mm long MS Helical door spring Welded to steel /Fixed to wooden door frame including roller and roller plate etc of approved quality complete all as specified and directed.

S&F hasp and staple 100mm safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap (when open) 30 mm complete all as specified and directed.

S&F magnet catcher for cup board shutter complete all as specified and directed.

S&F aluminium plate type II gate and shutter, hooks and eyes 125mm complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frame including taking out old wooden beads complete all as specified and directed.

S&F sheet glass ordinary quality 3mm thick, glazing with oil putty or wooden beads in squares n.exc 0.50 sqm each pane complete all as specified and directed.

S&F 3 mm thick figured glass, pin head type and glazing with oil putty or wooden beads in squares n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staples and wooden beads complete all as specified and directed.

S&F in repairs galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples and wooden beads complete all as specified and directed.

S&F in repair 25 mm dia aluminium drapery rod with wooden finish, decorative, including brackets, decorative finials at both ends & curtain rings 8 Nos (minimum) in one opening complete all as specified and directed.

S&F in repairs door closer hydraulically regulated, aluminium extruded section body, designation no. 3, universal type, suitable for door shutter of 851 to 1000mm in width and of weight between 61 to 80 kg complete all as specified and as directed.

M&L for preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as specified and directed.

S&F 0.63 mm thick Galvanised Corrugated Iron (CGI) sheeting with two corrugation side lap sheets having Zinc coating @120 gram per sqm inclusive both sides, fixed with 'J' type hook or 'L' type hook and washers as in roof covering etc complete all as specified and directed by Engineer-in-Charge.

All as per item no. 121 above but except sheeting fixed with coach screws/'J' type hook or L type hook and washers as in roof covering etc. complete all as specified and directed.

S&F 0.63 mm thick Plain Galvanised Iron (PGI) sheetss having Zinc coating @120 gram per sqm inclusive of both sides as in ridge, hips valley gutter, drip and straight flashing etc, fixed in any pattern complete all as specified and directed by Engineer-in-Charge.

S & F of 2.00 mm thick fibre glass reinforced transluscent corrugated sheeting with two corrugation side lap fixed with 'J' type or 'L' type hook bolts and washers as in roof covering etc. including dismantling of existing roof sheet complete all as specified and directed.

M&L for taking down of existing sunken slab treatment form the sunken portion and cleaning the surfaces by washing down with water and rubbish off the premises. (a) Cleaning and filling cracks with sealing compound, brushing neat with neat cement slurry @ 3.00 kg/ sqm and grouting in 25 mm thick plain cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) over sunken slab portion and finishing the top surfaces even and smooth without using extra cement . (b) M&L for two coats of acrylic cementitious water proofing coating (Dr Fixit pidifin 2K manufactured by M/s Pidilite industries Ltd or equivalent make as approved by GE) and followed by a overlay protective 15 mm thick screed/ rendering in CM 1:3 along with liquid water proofing at appropriate ratio of approved make on top surfaces of sunken slab after preparations as mentioned above. Method of application for acrylic cementitious water proofing coating is followed as per manufacturers instructions.

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following courses of treatment/specification from bottom to top:- (i) Taking out old roof treatment and roughening the same old concrete slab by picking, sweeping clean and washing down with water to remove dust etc. and applying cement slurry @ 3kg/Sqm (ii) Screed bed or bedding layer of mortar 15 mm thick in CM (1:4) for laying as in roof slab with mixing of WPC and surface finished fare and smooth without using extra cement. (Note: WPC shall be measured and paid for under separate items) (iii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.25ltr /Sqm conforming to IS:3384-1986. (iv) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall be applied by torch application over bituminous primer as specified. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (v) Applying one coat of aluminum paint over the APP modified membrance @ 0.11Kg/sqm. (NOTE:- The work of water proofing treatment shall be got executed through expert team of manufacturers or authorised applicator of manufacturer contractor shall be submitted documentary evidence in support of applicator engaged for approval of GE.)

Taking up or down steel tubing and connections 15 mm bore including cleaning for refixing or removal from site with all fittings complete all as specified and directed.

Taking up or down steel tubing and connections 20 mm bore including cleaning for refixing or removal from site with all fittings complete all as specified and directed.

S&F GI water tubing 15 mm bore medium grade (ISI marked) with all fittings fixed to wall or laid in floors complete all as specified and directed.

S&F GI water tubing 20 mm bore medium grade (ISI marked) with all fittings fixed to wall or laid in floors complete all as specified and directed.

S&F in repair Rotational moulded HDPE polyethylene 500 ltrs capacity water storage tanks three layered, (ISI marked) (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball valves 20mm dia high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball including 20mm dia GI medium grade over flow pipe, approx lenght 1.5 mtr, 25 mm dia wash out pipe with pluged at one end complete all as specified and directed.

S&F in repair rotational moulded polyethylene 1000 ltrs capacity water storage tanks , three layered, (ISI marked) (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball valves 20mm dia high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball including 20mm dia GI medium grade over flow pipe, approx lenght 1.5 mtr, 25 mm dia wash out pipe with pluged at one end complete all as specified and directed.

Cleaning and removing all scale and dirt etc from PVC/RCC/MS overhead tanks by using wire brush, bleaching powder or lime etc of required quantity and washing with clean water from tank and mouth of circulating pipe after disconnecting existing tanks, setting aside (or lowering if required) for repair, cleaning, etc and hoisting if required, reconnecting and refixing in position of capacity exc 500 n.exc 1000Ltrs incl writing "TC on -DD/MM/YY" with white synthetic enamel paint with 5 cm font in capital letters etc complete all as specified and directed.Note:- Proper record of cleaning of tank done under subject item shall be maintained in a register by sub division ,duly authenticated by user or user rep and Engineer-in-charge and shall be produced at the time of claiming any payments.

S&F in repairs ball valves 20mm dia high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed. (Minimum weight 20mm-210 gms)

S&F in repair of PVC tank cover suitable for 500 to 1000 ltr capacity water storage tank complete all as specified.

S&F in repair Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F in repair 15 mm bore pillar taps fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs CP bib tap 15 mm bore, cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed down, high pressure, screwed for iron pipe complete all as specified and as directed.

S&F in repair 15 mm bore brass chromium plated wall mixer with telephonic shower, complete all as specified and directed. Make : Jaquar Cat part No CON 217KN wall mixer, HSH 1929 (Shower) SHA 571(tube) Marc cat No. ES 517A(wall mixer) ES 531 (shower)/Pearl ARI-014 (wall mixer) HS 470 (Shower with tube)

S&F in repair 15 mm bore brass chromium plated wall mixer (3 in 1) complete all as specified and directed. Make: Jaquar Model No CON 281KN, HSH 1929 & OHS 1989/ Marc ES547A & ES 531 (Telephone shower) ES 549 (shower) ES 536 (Shower)/Pearl ARI 016 (wall mixer) HS 470 (hand shower with tube) SHA 512 (Arm) SHP 525 (OH shower)

S&F in repair 15 mm bore CP central hole basin mixer fancy type complete all as specified and directed. Make : Jaquar Model No. 167KNB, Mark: ESSCO ES-516/ Pearl ARI 013.

S&F in repair 15 mm bore angle cock, brass chromium plated, fancy type with round headed knob, suitable for 15mm bore iron pipe complete all as specified. Make:- Jaquar CON 167 KN or equivalent model of Prayag / Hindware.

S&F in repair angle cock, brass chromium plated, fancy type, with wall cap with round headed knob, suitable for 15mm bore iron pipe (2 in 1) complete all as specified. Make:- Marc ESSCO ES 553/Pearl ARI 005/equivalent Jaquar.

S&F in repair Health Faucet with 1 mtr metalic expandable tube & hook complete all as specified and directed. Make : Jaguar model No. ALDCHR 585/ Prayag model No BEA 41/Pearl HF-133, HF 134.

S&F in repair for PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair 32 mm bore PTMT waste pipe for wash hand basin complete all as specified and directed.

S&F in repair for grating doom 100mm dia of PTMT (minimum weight 25gms) complete all as specified and directed.

S&F in repair sink made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and waste pipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495 mm x 420 mm ,bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.Make:- Prayag / Nirali / Hindware

S&F in repair kitchen plate rack made of stainless steel sheet 1.00 mm thick of over all size 31'' x 30'' x 10'' fixed to wall with brass screws etc complete all as specified and as directed.Make:- Prayag Cat part no. P-346 or Bluestar cat part No BSKPR-314 or equivalent make of Hindware / Nirali

S&F in repair PVC (Plastic polymer Cistern) valve less, Syphonic action type, flushing cistern of capacity 10 litres, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete all as specified and as directed by Engineer-in-Charge.

S&F in repair Vitreous china wash hand basin, white, flat back of size 550 mm x 400 mm including bracket, cutting for and pinning the ends of brackets or erecting stands also including brass chromium plated waste coupling 32mm dia, PVC flexible waste pipe of adequate length and dia and PVC connection 15mm size 450mm length with PTMT nuts, complete all as specified and as directed by Engineer-in-Charge .Make:- Prayag cat aprt no. 4645 IRIS or equivalent make of Pearl/ Hindware.

S&F in repair Vitreous china squatting pan of Orissa Pattern of size 580x 440 mm ,white with ‘P’ or ‘S’ trap , front or back inlet but excluding flushing cistern and flush pipe including placing in position in floor and embedded in cushion of PCC type E2 ( using 40 mm graded crushed stone aggregates), 1:5:10 and finishing the top surfaces to match with the existing flooring complete all as specified and as directed .Make:- Prayag cat part no. 4055 or equivalent make of Pearl / Hindware.

S&F in repair Vitreous China wash down (EWC) water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) but including PVC water closet seat cover closed pattern with flat bottom and cover with PVC hinge device, flushing pipe, fixing bolt for pedestal pattern and making good to disturbed surfaces of floor etc complete all as specfied and directed. Make:- Prayag cat part no.4022 or equivalent make of Parryware / Hindware.

S&F in repair 110mm dia PVC (SWR) fioor trap including jointing to pipe complete all as specified and directed.

M& L for grinding and polishing of terrazzo /Kota stone floors, grinding by machine (Carborundum stone), rubbing even, cleaning with water, Grouting and filling, shining and polishing in the same shade all as specified in SSR Part-I complete all as specified and directed by Engr-in-Charge

Ms Amrik Singh Bahra