89040/E8

Amount

GENERAL SUMMARY NOTE: Schedule ‘A’ Part I to X are under Ser No. 2.00 to 10.00 are Prepriced by MES. Bidders shall insert their lumpsum amount in the Green coloured field under Col-6 only.

Lumpsum price worked out by the tenderer for INTERNAL WATER SUPPLY as listed in Schedule ‘A’ Part-II

Lumpsum price worked out by the tenderer for INTERNAL ELECTRIC SUPPLY as listed in Schedule ‘A’ Part-III

Lumpsum price worked out by the tenderer for EXTERNAL WATER SUPPLY (PRESSURIZED SEWAGE)/ TREATED WATER DISTRIBUTION (WATER SUPPLY) as listed in Schedule ‘A’ Part-IV

Lumpsum price worked out by the tenderer for EXTERNAL ELECTRIC SUPPLY STP & AUTOMATION FOR SEWAGE PUMPING/ EXTERNAL ELECTRIC SUPPLY (TREATED WATER SUPPLY) as listed in Schedule ‘A’ Part- V

Lumpsum price worked out by the tenderer for ROADS / FOOT PATH / CULVERTS as listed in Schedule ‘A’ Part-VI

Lumpsum price worked out by the tenderer for SEWAGE DISPOSAL as listed in Schedule ‘A’ Part-VII

Lumpsum price worked out by the tenderer for AREA DRAINAGE as listed in Schedule ‘A’ Part-VIII

Lumpsum price worked out by the tenderer for COMPOUND WALL/FENCING ,GATE AND PROTECTIVE WORKS as listed in Schedule ‘A’ Part- IX

Lumpsum price worked out by the tenderer for STANDBY GENERATOR SET as listed in Schedule ‘A’ Part- X

SCHEDULE `A' PART - XI TO XV are not prepriced by MES and prepriced rates indicating 0.0 under column 5 signifies this fact only. Bidders shall insert their rates in Green field under Col-6.

SCHEDULE 'A' PART I - BUILDING/ STRUCTURES

Designing and constructing Living accn for pump operator , WC, Bath of plinth area19.50 sqm and Lab Room of 7.50 Sq.m single storey with permanent specification complete with RCC -25 design mix including excavation in any types of strata, foundation concrete, footings, plinth beam, Col, lintel, roof beam, roof slab, Solid Block walling, internal & External plastering, finishing, Roof Treatment . Anti termite treatment, Rolling Shutter, Pressed steel door frame, flush shutter, glazed skelton door shutter, fly proof Box type steel window, PVC door, Wall & floor tiles, sanitary fittings & taps in toilets, plinth protection, including all soil waste pipe up to first manhole complete incl refilling of earth and disposal of surplus earth within 500 m lead etc complete all as specified and directed.

Desiging and Constructing Laboratery room of plinth area: 37.00 Sqm, single storey with permanent specification complete with RCC-25 design mix including excavation in any types of strata, foundation concrete, footings, plinth beam, col lintel, roof beam, roof slab, Solid block walling, internal & External plastering, finishing, Roof Treatment, Anti termite treatment, Rolling shutter, Pressed steel door frame, flush shutter, glazed skelton door shutter, fly proof Box type steel window, and laboratory sink with elbow operated bib cock, waste pipe up to first manhole complete incl plinth protection returning filling of earth and disposal of surplus earth within 500m lead etc complete.

Designing and constructing RCC sumpwell in M-30 mix of required capacity including excavation in all types of strata, foundation concrete, container walls, bottom slab, top RCC roof slab with CI manhole covers and with plaster and water proofing as per zonal specification including epoxy paint inside, refilling of earth and disposal of surplus earth within 50 m lead, including all piping connections, valves, internal electrification, MS ladder, ventilation shaft, BB chambers with 5m of outer wall of tank complete including test for water tightness and hydraulic functioning Sump Well 2.1 mtrs dia and 2.6 mtrs deep

All as per Item No. 12.03 above but 3.50 m dia and 3.30 m depth

All as per Item No. 12.03 above but 1.7 m dia and 3.20 m depth

All as per Item No. 12.03 above but 1.7 m dia and 1.4 m depth

All as per Item No. 12.03 above but 2.4 m dia and 4.10 m depth

All as per Item No. 12.03 above but 3.10 m dia and4.5m depth

All as per Item No. 12.03 above but 2.00m dia and 3..000 m depth

All as per Item No. 12.03 above but 3.40 m dia and 4.5m depth

All as per Item No. 12.03 above but 2.9 m dia and 3.50 m depth

All as per Item No. 12.03 above but 2.9 m dia and 3.4 m depth

All as per Item No. 12.03 above but2.10m dia and 2.7 m depth

All as per Item No. 12.03 above 5.5 m dia and 2.8 m depth

All as per Item No. 12.03 above 1.9 m dia and 3.90 m depth

All as per Item No. 12.03 above but 2.7 m dia and 3..000 m depth

All as per Item No. 12.03 above but 4.4 m dia and 2.7 m depth

All as per Item No. 12.03 above but 1.7 m dia and 2.6 m depth

All as per Item No. 12.03 above but 1.7 m dia and 3.50 m depth

All as per Item No. 12.03 above but 1.7 m dia and 3.0 m depth

Construction of Flush Tank of size 01mtr x 01mtr x01mtr complete all as shown on drawings and as Specified.

SCHEDULE 'A' PART XI -FIRE FIGHTING

Supplying and fixing of non-skid rubber mat 16mm thick and 900mm width as required including cutting to required lengths of approved make with Test Certificates for LT

Supplying and fixing of fire bucket painted red and duly filled with sand conforming to IS: 2546-1974 all as specified and directed

Supplying and fixing of MS stand suitable for supporting two buckets (Pedestal type) all as specified and directed

Supplying and fixing of MS stand suitable for supporting four buckets (Pedestal type) all as specified and directed

Supplying and fixing of shock restoration chart written in English and Hindi duly framed in all as specified and directed

Supplying and fixing of carbon dioxide fire extinguisher type 4 kgs. Capacity of approved make with wall mounting bracket as required conforming to IS: 2878/1976 (Push type) all as specified and directed

Supplying and fixing of first aid box as approved complete with standard kit as prescribed by Indian Red Cross all as specified and directed

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side all as specified and directed

SCHEDULE 'A' PART XII -SEWAGE TREATMENT PLANT

Supply, install, test & commissioning of Sewage Treatment Plant based on principle of aerobic attached growth non-clogging randomnly moving bed Bio-reactor Technology (MBBR) having capacity 600 KLD (Zone-1 Hanuman temple complex) with the DESIGN DATAS all as specified in ADG (D&C) Pune drawing No. ADG/2022/PHE/001, sheet No.01/05 and its connected drawings complete including all civil, pumbing and electricals works including connected automation all as shown on drawings and all as specified and directed Make of plant : (a) M/s Optimus Enviropro Pvt Ltd, (b) Ion exchange India Ltd, (c) Thermax Limited, (d) Fontus Water Ltd, (e) Hydrotech Pariyabaran and all other E-in-C's approved make.

Supply, install, test & commissioning of Sewage Treatment Plant based on principle of aerobic attached growth non-clogging randomnly moving bed Bio-reactor Technology (MBBR) having capacity 300 kLD at Zone-2 (MH Secunderabad location) with the DESIGN DATAS mentioned in ADG (D&C) Pune drawing No. ADG/2022/PHE/001, sheet No.02/05 and its connected drawings complete including all civil, pumbing and electricals works including connected automation all as shown on drawings and as specified. Make of plant : (a) M/s Optimus Enviropro Pvt Ltd, (b) Ion exchange India Ltd, (c) Thermax Limited, (d) Fontus Water Ltd, (e) Hydrotech Pariyabaran and all other E-in-C's approved make.coarse bubble v notch holes, etc complete all as specified and directed

Supply, install, test & commissioning of Sewage Treatment Plant based on principle of aerobic attached growth non-clogging randomnly moving bed Bio-reactor Technology (MBBR) having capacity 1100 kLD at Zone-3 (ABC lines) with the DESIGN DATAS mentioned in ADG (D&C) Pune drawing No. ADG/2022/PHE/001, , sheet No.03/05 and its connected drawings complete including all civil, pumbing and electricals works including connected automation all as shown on drawings and as specified. Make of plant : (a) M/s Optimus Enviropro Pvt Ltd, (b) Ion exchange India Ltd, (c) Thermax Limited, (d) Fontus Water Ltd, (e) Hydrotech Pariyabaran and all other E-in-C's approved make.coarse bubble v notch holes, etc complete all as specified and directed

Supply, install, test & commissioning of Sewage Treatment Plant based on principle of aerobic attached growth non-clogging randomnly moving bed Bio-reactor Technology (MBBR) having capacity 600 kLD at Zone-4 (371 Unit location) with the DESIGN DATAS mentioned in ADG (D&C) Pune drawing No. ADG/2022/PHE/001, sheet No.04/05 and its connected drawings complete including all civil, pumbing and electricals works including connected automation all as shown on drawings and as specified. Make of plant : (a) M/s Optimus Enviropro Pvt Ltd, (b) Ion exchange India Ltd, (c) Thermax Limited, (d) Fontus Water Ltd, (e) Hydrotech Pariyabaran and all other E-in-C's approved make.coarse bubble v notch holes, etc complete all as specified and directed

Supply, install, test & commissioning of Sewage Treatment Plant based on principle of aerobic attached growth non-clogging randomnly moving bed Bio-reactor Technology (MBBR) having capacity 1200 kLD at Zone-5 (Safilguda MAP location) with the DESIGN DATAS mentioned in ADG (D&C) Pune drawing No. ADG/2022/PHE/001, sheet No.05/05 and its connected drawings complete including all civil, pumbing and electricals works including connected automation all as shown on drawings and as specified. Make of plant : (a) M/s Optimus Enviropro Pvt Ltd, (b) Ion exchange India Ltd, (c) Thermax Limited, (d) Fontus Water Ltd, (e) Hydrotech Pariyabaran and all other E-in-C's approved make.coarse bubble v notch holes, etc complete all as specified and directed. NOTE FOR Item No. 14.01 to 14.05 : Tenderer shall go through the design datas given in Annexure I to Particular Specifications and drawings thoroughly before quoting the rates.

SCHEDULE 'A' PART XIII - : LAB EQUIPMENT

Supply, install, testing and commisioning of lab Stirrer all as directed.

Supply, install, testing and commisioning of Centrifuge all as directed.

Supply, install, testing and commisioning of PH Meter all as directed.

Supply, install, testing and commisioning of Turbidity meter all as directed.

Supply, install, testing and commisioning of Titration all as directed.

Supply, install, testing and commisioning of Colorimeter all as directed.

Supply, install, testing and commisioning of Autoclave all as directed.

Supply, install, testing and commisioning of Analytical balance all as directed.

Supply, install, testing and commisioning of Desiccators all as directed.

Supply, install, testing and commisioning of Hot air oven all as directed.

Supply, install, testing and commisioning of Water Bath all as directed.

Supply, install, testing and commisioning of Samples all as directed.

Supply, install, testing and commisioning of Refrigerator, 190 ltrs, 5 star rating inclusive of inbuilt voltage stablizer of suitable capacity all as directed.

Supply, install, testing and commisioning of COD Sensor / Probe all as directed.

Supply, install, testing and commisioning of DO Sensor / Probe all as directed.

SCHEDULE `A' PART - XIV- FITTINGS & FIXTURES AND MISCELLANEOUS ITEMS is not prepriced by MES and prepriced rates indicating 0.0 under column 5 signifies this fact only. Bidders shall insert their rates in Green field under Col-6.

(EXTERNAL WATER SUPPLY (PRESSURIZED SEWAGE)/ TREATED WATER DISTRIBUTION (WATER SUPPLY)) Supply, installation, testing and commissioning of Set of Two Sewage self-priming monobloc pumps, operating on three phase AC power supply, mechanical seal, CI casing & impeller, SS shaft, each pump should be complete with inlet butterfly valve, Outlet modem based electrically actuated butterfly valve, dual plate check valve, common header, interconnecting cable, and required foundation with weather protecting FRP canopy, complete all as directed and specified.

0.94 LPS at 10 m head

3.7 LPS at 7 m head

2.45 LPS at 5 m head

8.17 LPS at 05 m head

2.45 LPS at 8 m head

8.17 LPS at 8 m head

2.94 LPS at 6 m head

6.5 LPS at 2 m head

6.5 LPS at 3 m head

0.88 LPS at 8 m head

0.56 LPS at 9 m head

1.89 LPS at 4 m head

1.52 LPS at 6 m head

5.06 LPS at 6 m head

1.15 LPS at 8 m head

3.1 LPS at 4 m head

2.08 LPS at 5 m head

1.25 LPS at 7 m head

1.84 LPS at 9 m head

3.29 LPS at 4 m head

9.87 LPS at 4 m head

Supply, installation, testing and commissioning of Set of Two Sewage Submersible pumps, operating on three phase AC power supply, mechanical seal, CI casing & impeller, SS shaft, each pump should be complete with outlet electrical actuated butterfly valve, dual plate check valve, common header, interconnecting cable, and required foundation, complete in all respect. (a) 6.25 LPS with 5 m head

9.81 LPS with 6 m head

21.68 LPS with 3 m head

Supply and lay pipe ductile Iron, S/S including specials, Class “K-7” ,100 mm (4”) dia all as specified and directed.

Supply and lay pipe ductile Iron, S/S including specials, Class “K-7”, 150 mm (6”) dia

Construction of valve chamber of size 900 x 900 mm (Internal size) 900 mm deep with 200mm thick PCC block masonary walls built in CM 1:6 over 100 mm thick foundation concrete in PCC 1:4:8 type D2, (Using 40 mm graded coarse aggregate) with 100 mm off set, 15mm thick complete internal plaster and external plaster up to a depth of 15 cm below GL in CM (1:6), 3 mm thick MS sheet cover, double door welded to 50 mm x 50 mm x 6mm MS angle frame fixed with hold fasts in PCC 1:2:4 type B1 coping 50 mm thick in PCC (1:2:4) type B-1, 20mm x 6mm flat iron hinges with locking arrangement including lock sixty five mm, brassd and keys(Godrej/Shell), MS handles and applying two coats of synthetic eanmel paint over a coat of red oxide zinc chrome primer to all steel surfaces including excavation & earth work in any type of soil /soft disintegrated rock and disposal of surplus soil to a distance not exceeding 50 Mtr complete all as specified and directed

S&F, connecting and testing in repair of Cast Iron foot Valves flanged ends swing type operation with rubber seat as per IS : 4038 single disc with all standard accessories and tested including replacement of nuts, bolts, washers, gaskets, packings etc complete all as specified and directed of size 65mm dia

S&F, connecting and testing in repair of Cast Iron foot Valves flanged ends swing type operation with rubber seat as per IS : 4038 single disc with all standard accessories and tested including replacement of nuts, bolts, washers, gaskets, packings etc complete all as specified and directed of size 80mm dia

Supply, install, testing and commissioning of Centrifugal monoblock pump set with cast iron impeller, directly coupled with motor, suitable for of minimum total head 22meter and discharge min 16 LPS operated on AC 3 phase, voltage 380V, 50 Hz. The motor casing shall be of cast iron, pump shaft / motor shaft shall be of stainless steel,complete all as specified and directed. The pump and motor shall comply to all the requirements of relevant IS. (1W + 1S) Make: Grundfos/Kirloskar

Supply, install, testing and commissioning of Centrifugal monoblock pump set with cast iron impeller, directly coupled with motor, suitable for of minimum total head of minimum total head 20 meter and discharge min 8 LPS operated on AC 3 phase, voltage 380V, 50 Hz. The motor casing shall be of cast iron, pump shaft / motor shaft shall be of stainless steel,complete all as specified and directed. The pump and motor shall comply to all the requirements of relevant IS. (1W + 1S) Make: Grundfos/Kirloskar

Supply and laying High density polyethylene pipes (HDPE) of pressure rating 10 kgf/cm2 (PN 10) laid in trenches, fixed on walls etc complete all as specified and as directed of Size 90 mm (OD)

Supply and laying High density polyethylene pipes (HDPE) of pressure rating 10 kgf/cm2 (PN 10) laid in trenches, fixed on walls etc complete all as specified and as directed of Size 63 mm (OD)

Supply and laying High density polyethylene pipes (HDPE) of pressure rating 10 kgf/cm2 (PN 10) laid in trenches, fixed on walls etc as directed of Size 50 mm (OD)

Supply and laying High density polyethylene pipes (HDPE) of pressure rating 10 kgf/cm2 (PN 10) laid in trenches, fixed on walls etc complete all as specified and as directed of Size 32 mm (OD)

Supply and fix Gun metal Foot Valve conforming to IS 4038, 80 mm (3”) dia complete all as specified and as directed

Supply and fix Gun metal Foot Valve conforming to IS 4038, 100 mm (3”) dia all as specified and as directed

Supply and fix Air release valves with two air outlets, 80m dia bore and fixing up in cst iron water supply mains complete all as specified and as directed

Construction of valve chamber of size 1200X1200X1200mm (Internal) with 200mm thick PCC block masonary walls built in CM 1:6 over 100 mm thick foundation concrete in PCC 1:4:8 type D2, (Using 40 mm graded coarse aggregate) with 100 mm off set, 15mm thick complete internal plaster and external plaster up to a depth of 15 cm below GL in CM (1:6), 3 mm thick MS sheet cover, double door welded to 50 mm x 50 mm x 6mm MS angle frame fixed with hold fasts in PCC 1:2:4 type B1 coping 50 mm thick in PCC (1:2:4) type B-1, 20mm x 6mm flat iron hinges with locking arrangement including lock sixty five mm, brassd and keys(Godrej/Shell), MS handles and applying two coats of synthetic eanmel paint over a coat of red oxide zinc chrome primer to all steel surfaces including excavation & earth work in any type of soil /soft disintegrated rock and disposal of surplus soil to a distance not exceeding 50 Mtr complete all as specified and directed

Construction of valve chamber of size 750 x 750 mm (Internal size) 750 mm deep with 200mm thick PCC block masonary walls built in CM 1:6 over 100 mm thick foundation concrete in PCC 1:4:8 type D2, (Using 40 mm graded coarse aggregate) with 100 mm off set, 15mm thick complete internal plaster and external plaster up to a depth of 15 cm below GL in CM (1:6), 3 mm thick MS sheet cover, double door welded to 50 mm x 50 mm x 6mm MS angle frame fixed with hold fasts in PCC 1:2:4 type B1 coping 50 mm thick in PCC (1:2:4) type B-1, 20mm x 6mm flat iron hinges with locking arrangement including lock sixty five mm, brassd and keys(Godrej/Shell), MS handles and applying two coats of synthetic eanmel paint over a coat of red oxide zinc chrome primer to all steel surfaces including excavation & earth work in any type of soil /soft disintegrated rock and disposal of surplus soil to a distance not exceeding 50 Mtr complete all as specified and directed

M&L for road crossing/drain crossing by adopting trench less tunneling work through specified pipe jacking method by erecting the equipment to true to the allignment and gradient by haidrolic pipe jacking technique complete including tunneling, excavation in any type of soils including hard rock, MS casing pipe havy duty of size 100 mm dia with 6 mm thick in any length including jointing materials to carry LT UG cables of size upto 400 Sqmm and necessary conveyance charges of machinery and other required materials in co-ordination with the concerned authorites complete all as specified and as directed.

Supply & fix post top insulator epoxy type 11 kV suitable for air break switch/drop out fuse with necessary nuts, bolts, washers complete all as specified and directed.

Supply, Installation, testing and commissioning APFC Power panel of 50 KVAR (20+10+10+5+5 kVAR) outdoor type, factory made, CPRI approved, cubical feeder pillar box panel board IP 54 free standing sutable for working on 440 volts 3 phase 50Hz AC supply, floor mounted made out of 3.15mm thick CRCA sheet, duly powder coated, compartmental design with locking arrangement, weather and vermin proof with proper ventilation slots complete of suitable size comprising of Following items (For STP Zone IV):- (a) MCCB Three pole 100 Amps (16 kA) with Microprocessor release breaking capacity, 415 Volts - 01 Nos ( As Incomer) (b) Suitable capacity Capacitor Duty Contactor for 20kVAR, 10kVAR, & 5 KVAR Capacitor Bank 415V (c) Auto / Manual control for each capacitor bank. (d) 200Amps TPN Copper busbar with colour coded heat shrinkable sleeve. (e) Internal wiring with suitabnle size of PVC insulated stranded copper conductor cable duy crimped with copper lugs & ferruled.

Supply, Installation, testing and commissioning APFC Power panel of 40KVAR (20+10+5+5 kVAR) outdoor type, factory made, CPRI approved, cubical feeder pillar box panel board IP 54 free standing sutable for working on 440 volts 3 phase 50HzAC supply, floor mounted made out of 3.15mm thick CRCA sheet, duly powder coated, compartmental design with locking arrangement, weather and vermin proof with proper ventilation slots complete of suitable size comprising of Following items (For STP Zone III):- (a) MCCB Three pole 100 Amps with Thermal magnetic release breaking capacity 16kA, 415 Volts - 01 Nos ( As Incomer) (b) Suitable capacity Capacitor Duty Contactor for 20kVAR, 10kVAR, & 5 KVAR Capacitor Bank 415V (c) Auto / Manual control for each capacitor bank. (d) 200Amps TPN Copper busbar with colour coded heat shrinkable sleeve. (e) Internal wiring with suitabnle size of PVC insulated stranded copper conductor cable duy crimped with copper lugs & ferruled.

Supply, Installation, testing and commissioning APFC Power panel of 15KVAR (10+5 kVAR) outdoor type, factory made, CPRI approved, cubical feeder pillar box panel board IP 54 free standing sutable for working on 440 volts 3 phase 50HzAC supply, floor mounted made out of 3.15mm thick CRCA sheet, duly powder coated, compartmental design with locking arrangement, weather and vermin proof with proper ventilation slots complete of suitable size comprising of Following items (For STP Zone I & Zone-II):- (a) MCCB Three pole 40 Amps with Thermal magnetic release breaking capacity 16kA, 415 Volts - 01 Nos ( As Incomer) (b) Suitable capacity Capacitor Duty Contactor for 10kVAR & 5 KVAR Capacitor Bank 415V (c) Auto / Manual control for each capacitor bank. (d) 100Amps TPN Copper busbar with colour coded heat shrinkable sleeve. (e) Internal wiring with suitabnle size of PVC insulated stranded copper conductor cable duy crimped with copper lugs & ferruled.

Supply, Installation, testing and commissioning APFC Power panel of 25KVAR (10+10+5 kVAR) outdoor type, factory made, CPRI approved, cubical feeder pillar box panel board IP 54 free standing sutable for working on 440 volts 3 phase 50HzAC supply, floor mounted made out of 3.15mm thick CRCA sheet, duly powder coated, compartmental design with locking arrangement, weather and vermin proof with proper ventilation slots complete of suitable size comprising of Following items (For STP Zone V):- (a) MCCB Three pole 63 Amps with Thermal magnetic release breaking capacity 16kA, 415 Volts - 01 Nos ( As Incomer) (b) Suitable capacity Capacitor Duty Contactor for 10kVAR & 5 KVAR Capacitor Bank 415V (c) Auto / Manual control for each capacitor bank. (d) 100Amps TPN Copper busbar with colour coded heat shrinkable sleeve. (e) Internal wiring with suitabnle size of PVC insulated stranded copper conductor cable duy crimped with copper lugs & ferruled.

M&L for road crossing/drain crossing by adopting trench less tunneling work through specified pipe jacking method by erecting the equipment to true to the allignment and gradient by haidrolic pipe jacking technique complete including tunneling, excavation in any type of soils including hard rock, MS casing pipe havy duty of size 100 mm dia with 6 mm thick in any length including jointing materials to carry LT UG cables of size upto 400 Sqmm and necessary conveyance charges of machinery and other required materials in co-ordination with the concerned authorites complete all as specified and as directed.

Design Fabricating supply and errecting connecting and testing totally enclosed LT cubicle panel board 3 Phase 4 wire system outdoor double door front and back opening type, sloped canopy (Hood) on top extended 100mm all arround, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cable up to 185 Sqmm 3.5 core in and out, incoming and out going feeders duly marked on revited plates etc complete CPRI approved factory made fabricated out of 3mm thick CRCA sheet duly treated through 7 tank pre treatment process and painted with epoxy powder coated mat finish of SIEMENS GREY structural RAL 7032 shade colour,built in industrial type locking arrangement on front and back, and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs, Panel mounted on Anle iron frame of 50x50x6mm thick duly painted and embeded in PCC 1:3:6 45 CM below ground level and 15 Cm above ground level and consisting the following (Main Incoming Panel Board for STP - I , II & IV)

(a) Aluminium Busbar 200 Amps with sleeves and connectors set of 4 (b) I/C : MCCB four pole 100 Amps with thermal magnetic release breaking capacity 25 kA, 415 Volts - 01 No (c) O/G : MCCB four pole 63 Amps with breaking capacity 10 kA, 415 Volts -03 nos (d) MCCB four pole 32 Amps with breaking capacity 10 kA, 415 Volts - 05 nos (e) RYB Phase Indication lamp with fuse 1 set (f) MCB Three pole 6-32 Amps with breaking capacity 10 kA, 415 Volts - 05 nos (f) 3 Ph LED Ammeter (g) 3 Ph LED Voltmeter Control wiring with PVC insulated multi stranded copper conductor, insulators for busbar mounting 3 Nos of suitable CT's and accessories

Design Fabricating supply and errecting connecting and testing totally enclosed LT cubicle panel board 3 Phase 4 wire system outdoor double door front, side and top operating type, sloped canopy (Hood) on top extended 100mm all arround, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cable up to 50 Sqmm 3.5 core in and out, incoming and out going feeders duly marked on revited plates etc complete CPRI approved factory made fabricated out of 3.15mm thick CRCA sheet duly treated through 7 tank pre treatment process and painted with epoxy powder coated mat finish of SIEMENS GREY structural RAL 7032 shade colour,built in industrial type locking arrangement on front and back, and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs, wall mounted and consisting the following (For STP Zone III & Zone V)

(a) Aluminium Busbar 200 Amps with sleeves and connectors set of 4 (b) MCCB four pole 125 Amps with thermal magnetic release with breaking capacity 25 kA, 415 Volts - 01 no (Incomer) Outgoing : (c) MCCB four pole 100 Amps with breaking capacity 16kA, 415 Volts - 03 nos (d) MCCB four pole 63 Amps with breaking capacity 16kA, 415 Volts - 03 nos (e) MCCB four pole 32 Amps with breaking capacity 16kA, 415 Volts - 03 nos (f) MCB Three pole 6-32 Amps with breaking capacity 10 kA , 415 Volts - 03 nos (g) RYB Phase Indication lamp with fuse 1 set (h) 3 Ph LED Ammeter (j) 3 Ph LED Voltmeter (k) Control wiring with PVC insulated multi stranded copper conductor, insulators for busbar mounting 3 Nos of suitable CT's and accessories

Supply, Installation, test and Commissioning CPRI APPROVED factory fabricated, out door type,LT FEEDER PILLAR BOX double door , Both side openable made out of 3.15 mm thick CRCA Sheet of size 0.7 m X0.6 mX 0.35 m with projected Globe roof for rain water protection duly treated through 8 tank pre treatment process and painted with epoxy powder coated mat finish of SIEMENS GREY structural RAL 7032 shade colour Dust and Vermin Proof , Double door with both side opening including Neoprene Rubber Gasket,, suitable for 440 Volt 3 Phase 4 Wire System ,including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate comp-lete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. and embeded with 50X50X6mm Mild Steel Angle Iron Frame and 600 mm above the Normal Ground Level comp -lete with internal connection with suitable size of cable ,cable lugs,and cable glands PCC Foundation in Cement Concrete 1:3:6 (20mm Graded Stone Aggregate) and Test-ing after Installation complete all as specified and comprising of the following :–

(a) Aluminium bas bar 400amps - 04 Nos, supported with suitable size of heavy duty porcelin stand lock with suitable size of brass nut, bolts and washer with heat shrinkable PVC sleeving. The bar shall be colour coded (red, yellow and blue) for three phases and black for neutral. b) MCCB 200 amps ,415 volt ,25 KA Breaking capacity 4 pole Thermalmagnetic release duly connected to Bus Bar As IN COMING - 01 NosMake Legrand model no: 420015/ Equivalent from Schinder/L&T/Hagar

Supply, installation, commissioning and testing of LT panel Board (outdoor type) double door type cubical type made out of CRCA sheet 3 mm thick dust and vermin proof with aluminium busbar of 100 amps capacity and angle iron size of 30 x 30 x 4 mm. Panel should be covered from all side with front and back lockable door and hinges complete and powder coated. grouted in and incl PCC 1:3:6 with 20 mm graded stone aggregate type B-1 complete including supply and fixing of following accessories:- (a) MCCB TPN 32 amps, 4 pole, 415 Volt of breaking capacity not less than 10 KA- 01 No incomer. (b) DOL starter (with wideband coil & Single phase preventer ) with relay range 6-10 Amps suitable for 5 HP motor - 2 nos. (c) Indicator lamp (R,Y,B) (d) Digital Ammeter with suitable ratio of CTs (e) Digital Volt meter (f) Internal Wiring and connecting the switchgears and accessories

Supply, installation, commissioning and testing of LT panel Board (outdoor type) double door type cubical type made out of CRCA sheet 3 mm thick dust and vermin proof with aluminium busbar of 100 amps capacity and angle iron size of 30 x 30 x 4 mm. Panel should be covered from all side with front and back lockable door and hinges complete and powder coated. grouted in and incl PCC 1:3:6 with 20 mm graded stone aggregate type B-1 complete including supply and fixing of following accessories:- (a) MCCB TPN 32 amps, 4 pole, 415 Volt of breaking capacity not less than 10 KA- 01 No incomer. (b) DOL starter (with wideband coil & Single phase preventer ) with relay range 6-10 Amps suitable for 5 HP motor - 4 nos. (c) Indicator lamp (R,Y,B) (d) Digital Ammeter with suitable ratio of CTs (e) Digital Volt meter (f) Internal Wiring and connecting the switchgears and accessories

Supply, installation, commissioning and testing of Microprocessor Controlled Master Monitoring operating panel via 1 No ultra sonic sensors, 2 Nos. Sewage Pumps, 2 Nos Main Motorize valve to operate & act as a user controlled with visual annunciation panel, with Cordless transmitter unit modem satellite controlled and Non GSM, Non GPRS, Non Rf, Non RTU/iRTU & Non Internet based Net work for SCADA Remote monitoring & operation of complete sewage pumping network satellite based net work, The Panel shall be wall/Floor mounting Shall be of suitable size made of 1.5 sqmm CRCA sheet properly powder coated, consisting of following features :- (a) Main Micro Processor Controller Data Receiver/Transmitter unit Modem satellite base net work and Non GSM, Non GPRS, Non Rf, Non RTU/iRTU & Non Internet based Net work. (b) With SCADA Soft Ware For Mobile Phone for monitoring of water level via mobile phone non internet based and 32” LED Screen Receiver unit In mimic Graphic format Non internet /GPRS based. (c) The micro controller shall send SMS Alert to five mobile no’s in case of any tampering with the automatic system. (d) With Mimic graphic display of Size 12” /12” High Intensity Type LED Micro processor based for water level indicator and pump set ON/OFF Running graphical Mimic." (e) With Single/Reverse phasing protection & alarming through SMS to five mobile no’s. (f) Micro controller based complete monitoring system for pump motor three phase Voltage, current, P.F ,Kvarh& KWH.

(g) The micro controller shall send SMS Alert to five mobile no’s in case of single phasing, unbalance voltage/Current or any failure with the pump operation system of pump set. (h) With automatic controlling of pump set ON/Off Condition via ultra sonic sensor depending upon water level in Clear water UG Sump. (j) With automatic sequencer of pump set. (k) With Automatic transfer of pump set on failure of any pump set. (l) With automatic cool down of pump set after every 3 hours or as pre set timing to prevent pump set from over heating.

Supply, installation, testing & Commissioning of Ultra sonic non-contact sensor for level monitoring for Sewage Sump with Following specification: - Principal: Ultra sonic sound waves water level sensing. O/P Pot: 4-20 ma/0-20 V Data transmitting output pot SCADA Operation output pot Range as per sump depth

Supply, installation, testing & commissioning of 32” colored TFT/LED display monitor with RS 232, RS 485 & USB input port with SCADA operating soft waresatellite Controlled and Non inter net, Noncomputer, NonRF, NonRTU, NoniRTU and Non GSM based to monitor water level of clear water UG Sump of STP in mimic flash format complete all as specified and directed.

Supply, installation, testing & commissioning of wireless satellite receiver modem and Non internet Non computer, NonRF, Non GPRS and Non GSM based to monitor water level of Sump in flash format and expandable to up 100 Nos Over Head/Under Ground Tanks in future with smps power supply with RS 232, RS 485 & USB input port with SCADA operating soft ware satellite controlled all enclosed in powder coated MS box of suitable size complete all as specified and directed.

Supply, installation, testing & commissioning of Mobile software in 5 Nos mobile nos with Android based APP for monitoring water level in Mimic Format of stp clear water UG Sump satellite controlled Ringer Tone Based and NON SMS and NON Internet based complete all as specified and directed.

S & F hot press moulded SMC junction / terminal box of size with internal diamensions of 200 x 140 x 95 mm with hinged door, incl provision of 2 way connector 415 Volts made out of polycarbonate or bakelite and 1 No MCB of 6 Amps with DIN bar, drilling holes for cable connections, connecting incoming and or out going cables by providing suitable of size of cable lugs/glands, fixied on pole by means of clamps made out of MS flat iron of size 25 mm x 3 mm including dismantling of old unserviceable all as specified and as directed.Make: Hensel/Syntex/C&S/nyptune

S&F new generation energy saving and environmental friendly long life varsatile pressure die cast aluminium IP66 road way light fitting with high power LED as light source of capacity 60 watts with suitable drivers etc and connecting with 4.0 Sqmm aluminium conductor PVC insulated twin core weather proof cable etc, fixing to wall/poll with and including bracket made out of GI pipe of suitable dia light grade not less than 1.5 mtr long, bent to shape, fixed to Pole/Wall in any position with flat iron clamps of size 30 x 4mm including taking down old unserviceable street light fitting of any type and capacity complete all as specified and directed. Make : Havells cat No : ENDURAPEARLPLUSSL60WLED757SASYTOPC or techno commercial equivalent model in Philips /Bajaj /Luker /Wipro.

Design Fabricating supply and errecting connecting and testing totally enclosed LT cubicle panel board 3 Phase 4 wire system outdoor double door front and back opening type, sloped canopy (Hood) on top extended 100mm all arround ,separate compartment for each control gear,cable alley, provision of knock out type plates for various sizes of cable up to 185 Sqmm 3.5 core in and out , incoming and out going feeders duly marked on revited plates etc complete CPRI approved factory made fabricated out of 3mm thick CRCA sheet duly treated through 7 tank pre treatment process and painted with epoxy powder coated mat finish of SIEMENS GREY structural RAL 7032 shade colour,built in industrial type locking arrangement on front and back ,and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs ,Panel mounted on Anle iron frame of 50x50x6mm thick duly painted and embeded in PCC 1:3:6 45 CM below ground level and 15 Cm above ground level and consisting the folowing (For Recycled water Pump House)

Design Fabricating supply and errecting connecting and testing totally enclosed LT cubicle panel board 3 Phase 4 wire system outdoor double door front and back opening type, sloped canopy (Hood) on top extended 100mm all arround ,separate compartment for each control gear,cable alley, provision of knock out type plates for various sizes of cable up to 185 Sqmm 3.5 core in and out , incoming and out going feeders duly marked on revited plates etc complete CPRI approved factory made fabricated out of 3mm thick CRCA sheet duly treated through 7 tank pre treatment process and painted with epoxy powder coated mat finish of SIEMENS GREY structural RAL 7032 shade colour,built in industrial type locking arrangement on front and back ,and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs ,Panel mounted on Anle iron frame of 50x50x6mm thick duly painted and embeded in PCC 1:3:6 45 CM below ground level and 15 Cm above ground level and consisting the folowing (For Recycled water Pump House)

M&L for appplying 2.50mm thick 10 cm wide road marking Paint (reflective) of specified shade or colour using hot thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser propane tank heater and profile shoe heater driven by experienced operator, on road surface made free of all dirt, scales, oil grease, foreign materials, etc. complete all as specified and directed.

M&L for HDPE DWC PIPE 150MM OD SN-8 (IS:16098 II) 6 MTR LENGTH laid in trenches and jointed in collars as specified and directed.

MHDPE DWC PIPE 170MM OD SN-8 (IS:16098 II) 6 MTR LENGTH laid in trenches and jointed in collars as specified and directed.

MHDPE DWC PIPE 200MM OD SN-8 (IS:16098 II) 6 MTR LENGTH laid in trenches and jointed in collars as specified and directed.

M&L for DWCPE (SN8) 250 MM (OD)Pipe laid in trenches and jointed in collars as specified and directed.

HDPE DWC PIPE 250MM OD SN-8 (IS:16098 II) 6 MTR LENGTH laid in trenches and jointed in collars as specified

HDPE DWC PIPE 300 MM OD SN-8 (IS:16098 II) 6 MTR LENGTH laid in trenches and jointed in collars as specified and directed.

M&L for DWCPE (SN8) 300 MM OD Pipe laid in trenches and jointed in collars as specified and directed.

M&L for DWCPE (SN8) 400 MM (OD) Pipe laid in trenches and jointed in collars as specified and directed.

M&L for DWCPE (SN8) 500 MM ( OD) Pipe laid in trenches and jointed in collars as specified and directed.

M&L for DWCPE (SN8) 500 MM ( OD) Pipe laid in trenches and jointed in collars as specified and directed.

Supply, transportation and safe delivery to Site, unloading, safe storage, installation, testing and commissioning of 1 No. 100KVA, Phase & Neutral, 415 Volts, 50 Hz, Diesel Generating Set or equivalent make complete with CPCB-II Acoustic Enclosure. The Diesel Engine shall be capable of delivering required BHP at 1500 RPM and coupled with 100kVA, 415 Volts, 50 Hz Alternator at 1500 RPM mounted on a common base frame along with Engine mounted Instrument Panel complete all as specified and directed

A. General Diesel engine and alternator shall be closely coupled and mounted on a base plate of robust in construction. DG Set shall meet the requirements of environmental protection rules, 1986 as laid down by Ministry of Environmental & Forest read with GSR 371(E) dated 17.05.2002,GSR 520(E) dated 01.07.2003 , GSR 448(E) dated 12.07.2004, GSR 771 (E) dated 11.12.2013 & GSR 232 (E) dated 31.03.2014 ,Gazette Notification No. 167 dated.31.03.2014 and Gazette Notification No. 578 dated. 11.11.2014 amended up to date, in respect of "emission norms" for the engine and in respect of noise norms for DG sets. B. TURBOCHARGED DIESEL ENGINE: The turbocharged Diesel Engine shall be water cooled, developing required BHP at 1500 RPM with class A-1 electronic governing to deliver specified continuous KVA output at 0.8 Power Factor Lag at NTP conditions. The Diesel engine should be capable of providing 10% overload for one hour in every 12 hours continuous running at full load. The turbocharged Diesel engine shall conform to IS: 13018/1990(reaffirmed 2005) and IS: 10000 series (with latest Amendments.). Specific fuel consumption (SFC) shall be as per IS specification. C. The Turbocharged Diesel engine shall be complete with the following accessories: (a) Integral Fuel tank with air breather, drain plug with capacity for 8 hours of continuous running at full load or 990 litres capacity, whichever is lesser as per clause 8.0.

(b) Engine instrument panel as per clause 7.0 consisting of starting switch with key/Password protection, lube oil temperature and pressure gauges, High coolant temperature, RPM indicator and hour meter with additional feature of auto start/remote start and auto stop. (c) Safety control to shut down the engine in the event of over speed, low lube oil pressure and high engine water temperature. (d) Exhaust silencer residential type. (e) 12 V or 24 V starting system complete charging alternator or dynamo and cut-out. (f) Lead Acid - maintenance free batteries of suitable ratings with connecting cables. The batteries shall be supplied dry and in uncharged condition and shall conform to relevant IS only. (g) Anti-Vibration mountings for complete DG set in case of flexible coupling and for turbocharged engine in case of direct coupling. (h) The fuel level should be indicated with the help of fuel gauge meter. (i) There should be provision for filling the fuel from outside (as in case of automobiles) with locking arrangement. (j) Flywheel to suit flexible coupling. (k) Coupling with guard. (l) Air cleaner. (m) Radiator & Fan. (Blower Type)

(n) Fuel Injection Pump (o) Electronic Governor. (p) Lubricating Oil Filter. (q) Common Base frame for mounting of Diesel Generator Set: Sturdy, fabricated, welded Construction, channel iron base frame for mounting the above Engine & Alternator. D. Engine Mounted Instrument Panel (a) Starting switch with key (b) Battery charging indicator (c) Lub oil pressure gauge (d) Water temperature gauge (e) Run time Totaliser – Digital (f) RPM indicator – Digital (g) Emergency Stop Push Button (With provision to extend Remote STOP) E. Fuel Tank (a) Integral Fuel tank with air breather, drain plug with capacity for 8 hours of continuous running at full load or 990 litres capacity, whichever is lesser. (b) Calibrated Fuel level Indicator. (a) Fuel Inlet for filling with locking arrangement in the top lid. (b) Fuel outlet. (c) Air vent. (d) Drain plug. (e) Provision for Cleaning of Fuel tank.

F. Alternator a) The alternator shall be self excited and self regulated of 100 KVA rating in three phase at 415 Volts, 50 Hz, 1500 RPM & 0.8 PF and shall conform to IEC 60034 / IS:13364 (Part 2) / 1992(reaffirmed 2008). The alternator shall be of brushless type only with VG-3 Grade of voltage regulation. The alternators shall be screen protected, drip proof with IP-23 or better degree of protection as per IS: 4691/85(reaffirmed 2004). The alternator should be suitable to take unbalanced load as per IEC 60034 / IS: 13364 (Part-2)/1992(reaffirmed 2008). The Insulation class shall be H and suitable for operation at an design Ambient Air Temperature of 40o C, without any shall be H and suitable for operation at an design Ambient Air Temperature of 40o C, without any de-rating. b. The Alternator shall have cable box suitable for terminating with suitable capacity XLPE cable all as specified and directed mm PVCA cable. c. The Alternator shall have Brushless excitation. d. Insulation : Class "H" for Stator & Rotor e. Winding : Vacuum pressure impregnation f. Excitation : Brushless Compound Excitation System. g. Regulation : AVR h. Unbalanced Load : 3 Phase sensing of voltage and current and power factor to give good operation against unbalanced load. (30% capability)

i. Motor Starting Capacity : Shall possess Motor starting capacity of the order of 3 to 3.5 times the full load current. j. Manufacturing : Shall conform to the following Standards G. Specifications : IEC 60034 : NFC 51.111 : VDE 0530 : BS 5000 : IEC 2-3 : IS 13364 Protection : IP 23 or better Short Circuit Sustenance : Shall have High sustenance of Short Circuit current of 3 times ull load current for 3 Seconds. Epoxy Coating : All wound components shall be epoxy coated after impregnation Routine Tests : Shall be conducted on the machine at no extra cost. H. Excitation System I. The excitation shall be Permanent Magnet Generator (PMG) type. The PMG shall be a three phase high frequency AC Generator mounted on the main rotor shaft. The stator of the PMG shall be high frequency AC Generator mounted on the main rotor shaft. The stator of the PMG shall be three phase wound and the rotor shall be provided with permanent magnet.

The output of the stator shall feed the power supply to the Automatic Voltage Regulator (AVR). AVR range of voltage adjustment be + 5%. II. The excitation produced by this winding shall be set slightly above the required value, giving a regulation of + 1%. III. Apart from the voltage regulation characteristics the excitation system shall have the following features. a. Voltage build-up from residual magnetism. b. Protection against low speed operation c. Voltages dip on acceleration of full load 0.8 Power Factor in the order of 15 to 20%. d. Recovery time at constant speed for rated load application shall be 1.0 seconds (max). e. Recovery time at constant speed for rated load rejection shall be 1.5 seconds (max). f. 3 Phase sensed system shall allow good operation with unbalanced load system. g. Shall have good overload characteristics. The DG set shall be capable of taking 10 % overload for 1 hr in every 12 hrs of continuous operation. h. Harmonic distortion factor of output of alternator shall be less than 3% at open circuit voltage (IS 13364 Part 2).

J. Control Panel a. Control panel shall be fabricated with 14 gauge CRCA sheet and powder coated for weather - proof and long lasting finish. b. The control panel shall be consisting of the following parts/ features. i.Power Command 1.2 controller or equivalent ii. Indicating lamps for ‘Load ON’ and ‘Set Running’ iii. Instrument fuses duly wired and ferruled iv. Control system is a microprocessor based generator set monitoring, metering and control system with LCD display v. Intuitive operator interface which includes LED backlit LCD display with tactile feel soft-switches and generator set status LED lamps vi. Digital AVR with torque matching. vii. Digital Electronic Governing with temperature compensation and smart starting. viii. SAE J1939 interface to Full Authority Electronic (FAE) engines. ix. Remote start-stop from AMF. x. Engine metering: Oil pressure, Coolant temperature, Battery Voltage, Engine Speed, AC xi.Alternator metering: L-L Voltage and L-N Voltage, Current (1 and 3 phase), Volt-Amperes (phase and total) and Frequency. xii. Engine protection: Low lube oil pressure, High/Low coolant temperature, over speed, Battery

xiii. Over/Under/Weak Volts, Fail to crank/start, Sensor failure. xiv. AC Alternator protection: Over/Under voltage, Over/Under frequency, Over current, Short circuit and Loss of AC sensing. xv. Data logging: Engine hours, Control hours, Engine starts and upto 10 recent fault codes xvi. Configurable glow plug control xvii. Configurable cycle cranking xviii. 12 and 24 Volt DC operation xix. Sleep mode xx. Programmable I/Os (4 inputs and 2 outputs), expandable with AUX101/102 modules xi. Modbus interface (RS485 RTU) xii. In Power compatible (PC based service tool) xxiiiCertifications - meets the requirement of relevant UL, NFPA, ISO, IEC, Mil Std., CE and CSA standards H. Acoustic Enclosure The acoustic enclosure shall conform to the drawings approved by a Govt./NABL lab., for conformity to noise norms. The Acoustic enclosure should consist of following: (a) The enclosure should be fabricated out of CRCA sheet of minimum 1.6 mm thick. (b) The sheet metal components should be suitably pre-treated with 7 tank process and should be powder coated to have long life of enclosure.

(c) The battery should be accommodated in a separate tray in the enclosure. (d) There should be provision of drain plugs for draining lube oil and diesel. (e) The doors should be gasketed with quality gaskets to avoid leakage of sound. (f) The door handle should be lockable type. (g) Sound proofing of enclosures should be done with high quality rock wool/ mineral wool/foam/fibre glass wool. (h) The rock, mineral, fibre glass wool is further covered with fibre glass cloth and perforated powder coated sheet. i. special silencer should be provided along with the enclosure and proper angle inor support to control exhaust noise. (j) Specially designed louvers should be provided to control sound at air entry to the container and exit from the container. (k) It should have Type approval certificate and also COP certificate (if applicable) from certification agencies mentioning MOEF notification No.371 (E) dated 17.05.2002 or as amended and applicable at the time of supply. (l) Ambient temperature limit inside the canopy should be specified. (m) There shall be provision for emergency STOP from outside the enclosure.

All as per Item No.16.76 but of capacity 82.5 kVA

All as per Item No.16.76 but of capacity 62.5 kVA

All as per Item No.16.76 but of capacity 40.0 kVA

SCHEDULE 'A' PART XV (MANNING AND OPERATION OF STP )

Manning and operation, Routine maintenance of 01 (One) No of Sewage Treatment Plant of 600 KLD (Zone-1 Hanuman temple complex) , 300 kLD at Zone-2 (MH Secunderabad location,1100 kLD at Zone-3 (ABC lines) , 600 kLD at Zone-4 (371 Unit location) , 1200 kLD at Zone-5 (Safilguda MAP location) including all E/M inventory pertains to afore mentioned STP's shall be carried out round the clock including all Sundays and public holidays by employing the man power and shift timings as mentioned below for operation of plant daily including supply of water treatment chemicals (i.e. Bio septic clean powder, sodium Hypochloride, Dap enzime, Calcium Hypo Chloride and Bleaching powder etc.,), Activated carbon Filter media (ACF). Activated Sand filter media (ASF), MBBR fluidized bio-media, Bacteria culture and other consumables required for smooth running of STP Plant and provision of reliever for weekly off and carrying out daily, weekly, monthly, quarterly & half yearly maintenance etc., complete for First year after defects liability period (i.e after 24 months of handing over of STP) all as specified and as directed.

(a) Man power to be employed per day:-For Each STP (i) FGM(SK) Operator - 03 Persons One FGM(Operator) per shift of 8 hours each for 3 shifts (ii) Helper (Mate) - 01 Person in General shift (b) Shift Timings for FGM(SK) Operator:- (i) First Shift - 0600 hours to 1400 hours (ii) Second Shift - 1400 hours to 2200 hours (iii) Third Shift - 2200 hours to 0600 hours (c) Shift Timing for Helper:- (i) General Shift - 0900 hours to 1730 hours including 30 minutes lunch break from 1300 hours 1330 hours

Manning and operation, Routine maintenance of 01 (One) No of Sewage Treatment Plant of 400 KLD, 300 kLD at Zone-2 (MH Secunderabad location) ,1100 kLD at Zone-3 (ABC lines) , 600 kLD at Zone-4 (371 Unit location) , 1200 kLD at Zone-5 (Safilguda MAP location) including all E/M inventory pertains to afore mentioned STP's shall be carried out round the clock including all Sundays and public holidays by employing the man power and shift timings as mentioned below for operation of plant daily including supply of water treatment chemicals (i.e. Bio septic clean powder, sodium Hypochloride, Dap enzime, Calcium Hypo Chloride and Bleaching powder etc.,), Activated carbon Filter media (ACF). Activated Sand filter media (ASF), MBBR fluidized bio-media, Bacteria culture and other consumables required for smooth running of STP Plant and provision of reliever for weekly off and carrying out daily, weekly, monthly, quarterly & half yearly maintenance etc., complete for the remaining of first year and second year during defects liability period after completion of 11 Months of handing over of STP) all as specified and as directed.

(a) Man power to be employed per day:-For Each STP (i) FGM(SK) Operator - 03 Persons One FGM(Operator) per shift of 8 hours each for 3 shifts (ii) Helper (Mate) - 01 Person in General shift (b) Shift Timings for FGM(SK) Operator:- (i) First Shift - 0600 hours to 1400 hours (ii) Second Shift - 1400 hours to 2200 hours (iii) Third Shift - 2200 hours to 0600 hours (c) Shift Timing for Helper:- (i) General Shift - 0900 hours to 1730 hours including 30 minutes lunch break from 1300 hours 1330 hours

Manning and operation, Routine maintenance of 01 (One) No of Sewage Treatment Plant of 400 KLD, 300 kLD at Zone-2 (MH Secunderabad location) ,1100 kLD at Zone-3 (ABC lines) , 600 kLD at Zone-4 (371 Unit location) , 1200 kLD at Zone-5 (Safilguda MAP location) including all E/M inventory pertains to afore mentioned STP's shall be carried out round the clock including all Sundays and public holidays by employing the man power and shift timings as mentioned below for operation of plant daily including supply of water treatment chemicals (i.e. Bio septic clean powder, sodium Hypochloride, Dap enzime, Calcium Hypo Chloride and Bleaching powder etc.,), Activated carbon Filter media (ACF). Activated Sand filter media (ASF), MBBR fluidized bio-media, Bacteria culture and other consumables required for smooth running of STP Plant and provision of reliever for weekly off and carrying out daily, weekly, monthly, quarterly & half yearly maintenance etc., complete for the remaining period of second year during defects liability period after completion of 22 Months of handing over of STP) all as specified and as directed.

(a) Man power to be employed per day:-For Each STP (i) FGM(SK) Operator - 03 Persons One FGM(Operator) per shift of 8 hours each for 3 shifts (ii) Helper (Mate) - 01 Person in General shift (b) Shift Timings for FGM(SK) Operator:- (i) First Shift - 0600 hours to 1400 hours (ii) Second Shift - 1400 hours to 2200 hours (iii) Third Shift - 2200 hours to 0600 hours (c) Shift Timing for Helper:- (i) General Shift - 0900 hours to 1730 hours including 30 minutes lunch break from 1300 hours 1330 hours

Nanak Buildtech

Chauhan Associates