PROVN OF VARIOUS WORK SERVICES AT INDIRA BLOCK AT CHAFB

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed.

Demolition of brick or stone/boulders masonary, built in cement mortar complete all as specified and directed.

Demolition of cement concrete in ground floor and paving n/exe 15 cm thick below or above GL complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not bulking) removing serviceable tiles to store complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for ( reinforcement cut as reqd to facilitate demolition ). complete all as specified and directed. Note for item Nos 1 to 6 above: All debris and rubbish shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations. ( demolition item taken in schedule of credit contractor may quote rate accoridingly)

Dismantling plain or corrugated steel sheeting any guage, thickness including roof covering complete all as specified and directed.

Dismantling structural steel work incl door gates but excluding framed work complete all as specified and directed.

Dismantling wrought iron and mild steel work iof any description complete all as specified and directed.

Taking down chowkhat or frames with shutters exc 1.5 sqm but not exc 4 sqm each (w/o taking off shutters from the frame) complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exc 1.50 Sqm each complete all as specified and directed.

Taking down shutter of any description exe 1.00 sqm but not exc 2.00 sqm and refixing in the same opening incl easing etc complete all as specified and directed.

Excavating in trenches, not exc 1.5 m wide and not exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc 10 sq m on plan and not exc 1.5 m in depth and getting out hard/dense soil complete all as specified and directed.

M&L for PCC 1:4:8 Type D2 (40mm graded stone aggregare) in sub base of floor ,foundations, filling and mass concrete complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.of hard/dense soil complete all as specified and directed.

Removing excavated soils exceeding 1.5 km but not exc 5 km and depositing where directed complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B1 (20mm graded aggregate) as in sub base/levelling course/floor finishes etc complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C1 (20 mm graded aggregate ) as in plinth protection etc. complete all as specified and directed.

M&L for 100mm thick PCC 1:2:4 type C1 (20 mm graded aggregate ) as in floor finishes/laid in alternate pane complete all as specified and directed.

S&F Powder coated Aluminium windows of three tracks outer frame top, side sections, bottom frame(track) with guide track of size 92.5x31x1.50mm with sliding window shutters two nos with glass and one no with wire mesh(total 3 nos shutter) frame top and side bottom section with wheel track and inner locking section of size 40x18x1.5mm inculding glass 4 mm thick and aluminium wire cloth, 0.45mm nominal dia wire and average width of aperture 1.40 mm complete all as specfied and dierected.

S&F Powder coated Aluminium Frame work for grills Deco-grill Model DG-104(10mm) making shape and riveted with rivets and fixed with suitable channel complete necessary fixing arrangements etc complete all as specified and directed.

S&F18 to 19mm thick Prelaminated partical board, interior grade, pre-laminated one side with decorative choice lamination & other side balancing white lamination, and fixed with screw and Continuous (piano) hinges, 125mm long Hasp and staple and and prepared kitchen cabinate with shutter (and one or two self as per site requirement for sorage) and hanging on wall and also fixed to timber frame work where required complete all as specified and directed.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built upstandard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings complete all as specified and directed. Note : All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufactures catalouge for the corresponding aluminum sections/fittings.

S&F Anodised aluminium door shutters (any type, normal or sliding), aluminium section Powder Coating (minimum thickness of powder coating 50 micron) weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc complete all as specified pecified and directed by the Engr-in-Charge.

S&F 9 mm thick prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations complete all as specified and directed.

S&F 5.5 mm thick sheet glass, ordinary quality, fixed with necessary glazing clips, in squares exceeding 0.5 Sqm in each panel complete all as specified and directed.

S&F 8 to 9 mm thick Prepainted gypsum building boards of size 595 x 595mm PVC laminated at back side of board insulation & acoustic purpose flat in ceiling fixed or laid / including powder coated GI snap grid of size 605mm x 605mm frame work using 36.50 x 23.50 x 1.5mm main Tee, 23.50 x 23.50 x 1.5mm cross Tee and 25x25x1.5mm angles for false ceiling with screws fixed to false ceiling including hangers 4 mm dia G.I (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed. Note: The rate shall be inclusive of scaffolding and necessary arrangements.

S&F in repairs Collapsible steel gates, top hung, consisting of channels pickets, pivoted flat bars, top and bottom runners, brass handles etc erected in postion and securing runners with holdfasts and brackets including taking down existing collapsible steel gate of any description, complete all as specified and directed. Note : The rate quoted shall include for provision of suitable size of bed blocks in PCC 1:2:4 type B1 for securing of runners hold fasts.

M&L for Non skid ceramic coloured joint free tiles 7 to 8mm thick (square/ rectangular), area of each tiles exceeding 0.06 sqm but n exc 0.11 sqm, in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles,laid over and including cement screed bed 15 mm thick in cement mortar 1:6 laying floor finish complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surfaces 300 x450x7/300x600x7 mm thick , set and jointed in neat cement slurry and pointed in white or colour cement to match laid over 10mm thick cement plaster in cement mortar 1:4 complete all as specified and directed.

M&L for Precast cement concrete block masonry with soild blocks, type C1 1:3:6 using 20mm graded aggregate exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

M&L for Rendering 10mm thick in cement mortar 1:6 and 5mm thick in cement mortar 1:4 in two layers on fair faces of brick work or concrete surfaces with water proofing compound @ 200 ml per 50kg of cement or as per manufacturer's instruction etc finished even and smooth without using extra cement complete all as specified and as directed. (Note : WPC shall be measured and paid separetely)

M&L for Rendering 5mm thick on concrete surfaces of ceiling in cement morter 1:3 finished even and smooth without using extra cement complete all as specified and as directed.

M&L Granite 18 to 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and tabil top for fixing wash basin and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite shade including screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

S&F Steel window/ventilator with side hung shutter including projecting type hinges with steel handles and steel peg stay and with glazing bars complete with dovetailed or welded all as specified and as directed.

S&F Steel window/ventilator with side hung shutter including projecting type hinges with steel handles and steel peg stay and without glazing bars complete with dovetailed or welded all as specified and as directed.

S&F Pressed steel frames for doors size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc complete, as all specified and directed

M&L for PCC 1:3:6 type C-1 (using 20mm graded aggregate) as filled in pressed steel foor frames etc complete all as specified and as directed.

S&F Mild steel work as in band, strap, hold fast, clamp, cleat, hook, hinges base tie for floor, frame, support or stay for rain water pipe etc and other similar items conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

M&L for PCC 1:3:6 type C-1 (using 20mm graded aggregate) as in hold fast block including necessary form work etc complete all as specified and as directed.

S&F for 35 mm thick factory made second class hard wood plain framed panelled shutter ( two panel) with lock rail and panel of 9mm B.W.P. commecrcial ply or 12mm veneered particle board with commecrcial veneering on both face. The size of rail and stile as per IS 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F for 4mm thick sheet glass ordinary quality and fixed with aluminium beading in square not exc. 0.50 sqm in each pane complete all as specified and as directed.

S&F for 4mm thick Figured glass, pin head type and fixed with aluminium beading in squares not exc 0.5 sq m in each pane complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and as directed.

S&F Butt hinges 100mm medium weight cold rolled mild steel complete all as specified and directed.

S&F Mild steel sliding door bolt plate type stove enammelled black of length 300 mm with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts four on bolt plate and two on staple plate and fixed complete all as specified and directed

S&F 200mm long of barrel tower bolts stove enammeled black with bright bolt complete all as specified and directed.

S&F 150 mm mild steel pressed handles oval type stove enamelled black complete all as specified and directed.

S&F Factory made solid PVC door frame (chowkhat) of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS wire tube supplied and fixed in opening as per specification and drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.for factory made solid PVC moulded door shuters 28 to 30 mm thick (Stiles) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2 mm plain colour PVC sheet on back face with particle board core complete all as specified and directed.

S&F 100 mm long extruded Aluminium alloy anodised Butt hinges with galvanized mild steel hinge pin type C 22 complete all as specified and directed.

S&F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based carrugated steel sheet 0.50 mm th of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick as in ridge of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Excavation in post holes each not exc 0.50 cum in any type of soil,getting out, returning filling in and ramming earth or broken rubble mixed with earth around , in layers not exceeding 25 cm ,watering and removing surplus soil to a distance not exc 50 m and making good surface complete all as specified and directed.

M&L for cement concrete Type C2 1:3:6 ( 40 mm graded aggregate) in foundations , filing and mass concrete complete all as specified and directed.

S&F roof trusses (framed), trussed, purlins,crane gantries, rails and fastnings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. fe-410 (gde E-250) complete all as specified and directed.

S&F Plates (plain or chequered) channels,distance pieces, cleats etc.square cut or notched including riveted, bolted or welded attachment complete all as specified and directed.

S&F Framed work such as grills ,shouldered and/or riveted,or forged into spikes; framed,guard bars; barred iron doors;ladders; framed balusters; walk,ways; railings; framework of water tanks and similar work,conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for providing cement concrete type B-0 (1:2:4) using 12.5mm graded stone aggregate as in roof kerbs, padding or mud stops, rounded or chamfered on edges complete all as specified and directed

M&L for cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified and directed.

M&L for Rendering 10mm thick in cement mortar 1:3 on roof padding finished even and fair with approved water proofing compound @ 200ml per 50kg of cement or as per manufacturer's instruction all as specified and as directed. (Note : WPC shall be measured and paid separately as supply only under relevent item)

Supply only liquid water proofing compound complete all as specified and directed.

M&L for water proofing treatment on horizontal and vertical surfaces with Providing and laying / fixing TPO (Thermoplastic Polyolefin) membrane including cleaning the surface and laying of 200GSM Geo textile and cover up with TPO RF 1.2 mm thermoplastic membrane on roof and up to 300 mm of parapets and crumple joint including junction of roof and parapet, welding the seam joints with hot air gun/machine and terminate the corners with extra protection to bear the high wind pressure. The TPO should be thoughroly tightened with the lower structure using mechanical fastening properly to avoid the corners and seam joint failure complete all as specified and directed. Make :Asian paints TPO or equivalent product of M/s Bauchemic/CIPY/SIKA/Pidilite/Dr fixit TO membrane/ BERGER

S&F in repairs Rotational moulded polyethylene water storage tank (cylindrical or vertical with closed top) 500ltrs capacity hoisted and fixed in position including dismantling of existing water tank and disconnecting pipeline connection as specified and as directed.

S&F in repairs Rotational moulded polyethylene water storage tank (cylindrical or vertical with closed top) 2000 ltrs capacity hoisted and fixed in position including dismantling of existing water tank and disconnecting pipeline connection as specified and as directed.

S&F Ball valve high pressure of PTMT with epoxy coated aluminium rod and highdensity plastic ball screwed for 20mm dia iron pipe and fixed (minimum wieght 15mm-142gms/20mm 210gms/25mm 455gms/40mm 690gms complete all as specified and directed.

S&F Plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repairs plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device suitable as well as for anglo indian WC complete all as specified and directed.

S&F in repairs Vitreous China wash down water closet pan (Pedestal Pattern), EWC White with 'P' or 'S' trap, including provision of fixing bolts and connecting upto drain and flushing pipe etc. complete all as specified and directed.

S&F in repairs vitreous china squatt pattern, Orissa Pattern size 580x440mm White,with integral Foot rests and 'P' or 'S' trap, white, including provision of fixing bolts and connecting upto drain and flushing pipe etc complete all as specified and directed.

S&F in repairs PVC Flushing Cistern 10 Ltrs Capacity Syphonic action type with Flush pipe low level, with inlet ball valve,Float chain& pull & brackets, including making necessary connections to water supply pipe line and jointing to WC etc complete all as specified and directed.

S&F in repair Chromium plated brass 15 mm dia health faucet with 8 mm dia, 1.2 m long flexible tube with wall hook complete necessary fixing arrangements etc complete all as specified and directed.

S&F in repairs vitreous China wash basin, white flat back, size 550x400mm including cutting for and pinning in ends of brackets or ereesing stand complete all as specified and directed.

S&F in repairs Brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm between flanges complete all as specified and directed.

S&F in repairs 15mm PVC connection 600mm long between ends with PTMT nut and washer complete all as specified and directed .

S&F in repairs Toilet paper holder of stainless steel fixed by CP brass screw in wall complete all as specified and directed.

S&F 110mm PVC (SWR) sanitary conncetion for WC bent type complete all as specified and directed.

S&Fin repairs 15 mm bore fancy type, chromium plated Stop valves / Angle cock screwed down high pressure with crutch handle screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F in repairs CP two way stop cock with all accessories complete all specified and directed.

S&F in repairs 15 mm bore fancy type CP bib taps cast copper alloy with crutch or butterfly nuts , handle, screwed down for iron pipe complete all as specified and directed.

S&F in repairs gratings doom 100mm dia of PTMT(minimum weight 25 gms) complete all as specified and directed.

S&F in repairs 15 mm bore pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specifed and directed.

Taking up or down 15mm dia GI Tubing and connections including cleaning for refixing or removal to store complete all as specifed and directed.

Taking up or down 20 mm dia GI Tubing and connections including cleaning for refixing or removal to store complete all as specifed and directed.

Taking up or down 25 mm dia GI Tubing and connections including cleaning for refixing or removal to store complete all as specifed and directed.

S&F 15 mm bore GI tubing medium grade galvanished with all fittings and fixed complete to walls & floors etc complete all as specifed and directed.

S&F 20 mm bore GI tubing medium grade galvanished with all fittings and fixed complete to walls & floors etc complete all as specifed and directed.

S&F 25 mm bore GI tubing medium grade galvanished with all fittings and fixed complete to walls & floors etc complete all as specifed and directed.

S&F in repair 20 mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed complete all as specifed and directed.

S&F in repair 25 mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed complete all as specifed and directed.

S&F in repairs 110mm dia PVC (SWR) pipes single socketed, in any lengthwith rubber ring joints, fixed to wall including dismantling of old pipe (sewage/rain water/any type) complete all as specified and as directed. Note :- Quoted rate shall deemed to include cost of scaffolding or ladders etc required for approaching for repair work ( Ground floor to Seventh Floor).

S&F in repairs 75mm dia PVC (SWR) pipes singlesocketed, in any lengthwith rubber ring joints, fixed to wall including dismantling old pipe (sewage/rain water/any type) complete all as specified and as directed. Note :- Quoted rate shall deemed to include cost of scaffolding or ladders etc required for approaching for repair work ( Ground floor to Seventh Floor).

S&F 75mm dia PVC (SWR) bend with access door of any radius complete all as specifed and directed. Note :- Quoted rate shall deemed to include cost of scaffolding or ladders etc required for approaching ( Ground floor to Seventh Floor).

S&F 110mm bore PVC (SWR) bends of any radius complete all as specified and directed. Note :- Quoted rate shall deemed to include cost of scaffolding or ladders etc required for approaching ( Ground floor to Seventh Floor).

S&F 75mm bore PVC (SWR) bends of any radius complete all as specified and directed. Note :- Quoted rate shall deemed to include cost of scaffolding or ladders etc required for approaching ( Ground floor to Seventh Floor).

S&F in repairs 75 mm bore PVC(SWR) floor trap, plain with grating including jointing with solvent cement complete all as specifed and directed.N Note :- Quoted rate shall deemed to include cost of scaffolding or ladders etc required for approaching.

S&F in repairs 75mm dia PVC (SWR) multi floor trap with grating including jointing with solvent cement complete all as specifed and directed. Note :- Quoted rate shall deemed to include cost of scaffolding or ladders etc required for approaching.

S&F in repairs for PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specifed and directed.

S&F in repairs urinal Spreader incl fixing with 15mm dia pipe complete all as specifed and directed.

S&F in repairs Vitreous china urinal, bowl type flat back of size 465 x 355 x 265 mm white (minimum), with grating, fulsh pipe and union for discharge pipe complete all as specifed and directed.

M&L for preparation of new plastered surfaces of wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant priming paint complete all as specifed and directed.

M&L for applying one coat of OBD to old treated surfaces of wall including preparation of old surface of walls (by washing down,rubbing down and stopping of distempered surface),complete all as specified and directed.

M&L for applying one coat of white wash to old treated plastered or un-plastered surfaces of ceilling including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots) complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceilling and applying two coat of white wash complete all as specified and as directed.

M&L for preparing new plastered or un plastered surface of walls and applying two coats of Cement base paint on walls over a coat of chalk primer through mechanical means complete all as specified and directed.

M&L for preparing old plastered or un plastered surface of walls and applying one coats of Cement base paint on walls through mechanical means complete all as specified and directed.

M&L for two coats of synthetic enamel paint on new steel surfaces over a coat of red-oxide primer including preparation of surfaces, over 10cm width or girth complete all as specified and directed.

M&L for one coat of synthetic enamel paint on old steel surfaces over coat of red-oxide primer including preparation of surfaces, over 10cm width or girth complete all as specified and directed.

M&L Applying one coat of white wash to old treated plastered or un-plastered surfaces of wall including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots) complete all as specifed and directed.

M&L Applying one coat of synthetic enamel paint to old painted wooden surfaces of any description, not otherwise described, over 10 cm width or girth including preparaton of surfaces complete all as specifed and directed.

Removing building materials etc. (other than spoil payable under items -earthwork) to a distance of 30.00 km or above, beyond the lead included in the rates, including loading, unloading and stacking at the destination complete all as specified and as directed

Surface excavation not exceeding 30 cm deep and average 15cm deep and getting out hard/dense soil complete all as specified and directed.

M&L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L 7.5 cm thick (compacted thickness) WBM, with coarse aggregates of grading 2 (63 to 40mm size) or of grading 3 (50 to 20mm size), spread, rolled and consolidated to gradient and camber required complete all as specified and directed

M&L for coloured 60mm thick factory interlocking cement concrete paver blocks any shape and size confirming to IS 15658-2006 of M-35 grade with grey cement and no pigment manufacturing by vibrating process over 40-50mm thick M sand cushion complete all as specified and directed. (Note: Shape of block shall be approved by Engr-in Charge prior to execution)

M&L for 75mm thick PCC 1:4:8 type D-2 (40mm graded aggregate) as in sub base complete all as specified and directed.

M&L for chequered cement concrete tiles glossy finished 30cm x30cmx25mm th with grey cement and pigment , set , jointed and pointed in neat cement slurry in floors laid over 15 mm thic screed bed in cm 1:6 complete all as specified and directed.

Demolition of plain cement concrete in foundation/copings/bed concrete of drain pipes in any position all as specified and directed. Note: All debris and rubbish shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations.

Removing excavated material to a distance not exceeding 50 meters and deposited where directed at level not exceeding 1.5 meters above the starting point complete all as specified and directed.

Demolition and breaking up drain pipes of internal dia 150mm (salt glazed ware, AC or reinforced concrete ) set cement mortar complete all as specified and directed.

M&L for plain cement concrete 1:2:4, type B-1 using 20 mm graded stone aggregate as in coping bed plates, haunching benching ,water trough and the like including weathering, slightly rounded or chamfered angles and throating including use of necessary form work and finishing the surfaces even and smooth without using extra cement all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc complete all as specified and directed.

M&L for Plain cement concrete 1:2:4, type B-1 using 20 mm graded stone aggregate as in surface channel, drain complete all as specified and directed.

M&L for Plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregated as in bed to 150mm bore drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L Salt glazed stone ware drain pipes 150 mm internal dia, grade `A' laid in trenches and jointed complete all as specified and directed.

M&L for Precast cement concrete 1:2:4, type B-1 using 20 mm graded stone aggregate as in cover salabs and the like, set in cement mortar 1:6 with plain fair faces complete with joints to match all complete all as specified and directed.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required including cranking and binding with mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar 1:4,on fair faces of brick work/concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Cutting in to existing man holes for connecting new drains for internal dia of pipe 150mm, making good to pipe and rendering, cutting out existingbenching for and forming branch channel (1/2 round or 3/4 section) in cement mortar 1:2:4 type B1 smooth finished and reforming benching as required complete all as specified and directed.

S&F on surface and wall mounted LED batten with polycarbonate housing and initigarated electronic drive 20 Watt fixture 4 feet, provided for efficient heat dissipation with policorbonate diffuser and integrated electronic driver and all accessories pre-wired including connection with 2 core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F ceiling rose, 65 x 50 mm surface type with 3 terminals incl connection complete all as specified and directed.

M&L for sub main wiring with 1.5 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable drawing into and including PVC conduit / casing capping of suitable size with all accessories and connected to common earth dolly with suitable copper lugs and making good to the disturbed surfaces to match the existing complete all as specified and directed

S&F ceiling recessed mounted LED panel type of size 2 ft x 2 ft, 36 W, 230 V, complete with driver full window glarefree opal diffuser LED panel with CRCA powder coated white housing complete with all accessories required for connection and making good the disturbed ceiling complete all as specified & directed

S&F energy saving LED flood light fitting, 100 watt, envioronmental friendly, long life, die cast aluminium IP 66 comprising with electronic driver and all accessories, pre-wired, fitting to be fitted on wall / pole with necessary fixing arrangement with nut, bolts, washers etc as required/directed at site incl connection with PVC insulated copper conductor cable 1.5 Sqmm, 3 core complete all as specified & directed.

S&F sheet metal enclosure distribution board, single pole and neutral, AC, 240 volts, 08 way, with 200 Amps rated copper bus bar and double door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall complete all as specified & directed

S&F MCB SPN 32/40 amps, 240 Volts, AC of breaking capacity 10 KA, 'C' curve and connections by using suitable copper lugs complete all as specified & directed

S&F MCB, SP, AC, 240 volts of 10 to 32 Amps capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed

Supply, installation, testing and commissioning of hi wall mounting air cooled inverter split type Air conditioner units complete with cordless LCD remote control unit and with turbo cool, stabilizer free operation, energy saver, anti corrosive blue fins for protection in built air ioniser and plasma filter for better indoor air quality with 5 star rating and the out door unit will be fixed in open space with proper foundation or on wall with proper fixing/supporting stand arrangements including 3 mtr suction & discharge refrigerant copper pipe line with high EER of 2.0 TR Capacity complete all as specified and directed.

S&F sheet metal enclosure with socket plug top and neutral enclosure with a two pin and earh plug and socket complete with one SPN MCB 20 Amps 'C' curve type complete all as specified and directed

S&F Copper tubing for refrigerant suction line of Split AC of size 16 mm drawn through pipes/ fixed to walls/ laid on floor or roof in all respects,complete all as specified and directed.

S&F Copper tubing for refrigerant discharge line of Split AC of size 6 mm drawn through pipes/ fixed to walls/ laid on floor or roof in all respects,complete all as specified and directed

S&F Heat insulation superior quality nitrile rubber of 9 mm thickness, ISI marked for copper tubing of any size of refrigerant line including necessary clamps, PVC tape knots, in all respects complete all as directed.

M&L for sub main wiring with 4.0 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable with and including continuous earth wire of size 4.0 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable drawing into and including rigid non-metallic PVC concealed conduit of 20 mm dia, medium grade with all conduit accessories and connected to common earth dolly with suitable copper lugs including all cutting / chases etc in stone/ brick masonary/ walls and making good to the disturbed surfaces to match the existing complete all as specified & directed

M&L for sub main wiring with 16 Sqmm nominal cross sectional area, four single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable with and including two runs of continuous earth wire of size 16 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable drawing into and including rigid non-metallic PVC conduit on surface of 32 mm dia, medium grade with all conduit accessories and connected to common earth dolly with suitable copper lugs including all cutting / chases etc in stone/ brick masonary/ walls and making good to the disturbed surfaces to match the existing complete all as specified & directed

S&F sheet metal enclosure distribution board triple pole and neutral TPN, AC, 440 volts, 04 ways with 200 Amps rated copper bus bar and metal double door suitable for MCB TPN 63 Amps as incomer and MCB SPs as outgoing along with cable end box for above DB and flush to wall including all cutting etc in wall complete all as specified & directed (Note: MCB TΡΝ & MCB SPs shall be measured and paid seperately)

S&F MCB TPN 63 amps, 415 Volts, AC of breaking capacity 10 KA, 'C' curve and connections by using suitable copper lugs complete all as specified & directed.

S&F MCB, SP, AC, 240 volts of 06 to 32 Amps capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Cutting of existing stone masonry wall for crossing the suction discharge pipe line and electric line connection of split type Air conditioner and after the connection necessary cement work will be provided for making the surface as good all as specified and directed.

S&F AC drain hose outlet PVC pipe of standard size 20 mm complete all as specified and directed

M&L for wiring control copper cable of 2.5 sq.mm 4 core from outdoor to indoor unit complete all as specified and directed