CWE(S)/NORTH/TOKEN/07 OF 2023-2024

Amount

Taking down of old bituminous tarfelt or any other type of roof treatment from roof/ concrete surfaces removal to distance exceeding 250 metres and not exceeding 500 metres from the site and cleaning of the roof surface with wire brush to make it free from dust, dirt etc complete all as specified and as directed

Demolition of cement concrete of any description and in any position not otherwise specifically provided in roof padding concrete etc complete incl removal of demolished material to a distance complete all as specified and as directed

M&L for PCC 1:2:4 Type B0 using 12.5 mm graded aggregate with 2% by weight of cement or as per manufacturer's instructions water proofing as in levelling course, haunching, coping and similar works over RCC roof surface and RCC over head tank top surface including rounded or chamferred on edges and formwork etc all as specified and directed. Note: Water proofing compound will be measured and paid separately under relevant item in this schedule, complete all as specified and as directed.

M & L for providing water proofing treatement with APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick reinforced with polyester non oven fabric ( weight not less than 150gm/Sqm) applyied on one coat of oil based bitumen emulision primer @ 0.3 lit per sqm ( OR as per the directions of manufacturer instructions) including cleaning of surface thoroughly from dust, dirt and projections. Laying of membrane by forced ( torch) application with 10cm overlaps . A coat of blown bitumen 85/25 grade @ 1.2 Kg/sqm to be applied on top of memberane, finally coating the surface with bituminous aluminium paint @ 100gm/Sqm complete all as specified and as directed

Material and labour for rendering 10mm thick on roof surfaces in cement mortar 1:4 duly mixing with water proofing compound at the rate of 3% by weight of cement and finished even and smooth complete all as specified and as directed Note: Water proofing compound will be measured and paid separately under relevant item in this schedule, complete all as specified and directed

Dismantling of CGI/PGI sheet roofing any gauge and any thickness including ridge, valley gutter etc complete all as specified directed.

Supply and fix pre-painted galvalume aluminium zinc coating galvanised based Corrugaed steel sheet 0.50mm thick, AZ-150 of approved colour having tensile strength of 550 Mpa as roof covering/cladding to wall fixed with self tapping (SD) screws complete all as specified and directed.

Supply and fix pre-painted galvalume aluminium zinc coating Corrugaed steel sheet 0.50mm thick, AZ-150 of approved colour having tensile strength of 550 Mpa as ridge, gutters fixed with self tapping (SD) screws complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc .complete all as specified and directed.

S&F joist channel, angle or tee sections, fixed independently without connecting plates, etc., (cut to ordinary lenghts i.e within 20mm of the length indicated of Fe 410-W ( Gde-E-250) quality A, complete all as specified and as directed

M&L for preparation of new surfaces of steel, of any description, not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided complete incl removal of demolished material to a distance complete all as specified and as directed.

M&L for RCC M25 type 1:1 1/2 : 3 (being small quantity) using 20MM graded granite/tap stone aggregate as in Lintel band etc complete all as specified and as directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunhings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs,etc. also splays between floors and beams etc as in rough finished flat surfaces of concrete complete all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over including all cutting bending, binding, cranking placing & binding with MS wire (annealed) not less than 0.90mm dia complete all as specified and as directed.

M&L for mild steel TMT bars 5mm dia and over upto and including 10mm dia as in stirrups , spacers and binders etc., including all cutting bending, binding, cranking placing & binding with MS wire (annealed) not less than 0.90mm dia complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar with all quoins, arches, pillars, etc but excluding ashlar facings, dressed stone work and precast concrete articles including disposal of the rubbish out off the premises complete all as specified and directed.

Material and labour for brick work with fly ash bricks old size, straight or curved on plan exceeding 6.0 metre mean radius in half brick thick walls built in cement mortar 1:6 complete all as specified and directed

Material and labour for walling of squared rubble masonry regular coursed, Secunderabad type, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed

-do- all as per item above but except stones complete all as specified and directed. Note- Serviceable stones obtained vide demolition item above shall be reused after removing mortar and cleaning with water complete all as specifed and directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded aggregate) in copings, kerbs, channels, water through and the like including weathering, slightly rounded or chamfered angles and throating as directed chamfered necessary for work, complete all as specified and as directed

Taking down cement plaster of any description and thickness on brick walls including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed

Material and labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.

Material and Labour for rendering 25mm thick in two coats, dubbing out coat average thickness of 15mm thick in cement mortar (1:6) on irregular face of stone masonary walls and 10mm thick top coat in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 without using extra cement complete all as specified and as directed.

M & L for rendering 5 mm thick on concrete surfaces such as ceiling or soffits of chhajas etc; in CM 1:3 finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over priming coat on walls, complete all as specified and as directed.

M & L for preparing newly plasterd wall surfaces of walls and applying two coats of distemper oil emulsion over 3 mm thick wall care putty and a coat of primer etc complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash on wall surfaces, complete all as specified and directed.

M & L for preparing newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removal of rubbish/ demolished materials out of MD land complete all as specified and as directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and as directed.

M&L for machine cut kota stone flooring 20-25mm thick over cement screed base of 15mm thick in CM(1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab inclduing rubbing and polishing complete all as specified and as directed.

M&L for machine cut kota stone as in skirting / dado 20-25mm thick over cement plster of 10mm thick base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab inclduing rubbing and polishing complete all as specified and as directed.

M&L for 75 mm thick plain cement concrete 1:4:8 mix,type D2 (using 40 mm graded stone aggregates) as in subbase to floor complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) of size not exceeding 1.5 SQMs each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) of size exceeding 1.5 Sqm and n.exc 4.0 sqm each complete all as specified and directed.

S&F 125 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete as specified, supplied and fixed, complete all as specified and directed.

S & F 35 mm 2nd class hard wood factory made glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars) edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of member of shutter as specified in SSR Part-I section 8 clause 8.24(a) etc complete all as specified and directed.

Supply and fix steel windows (fly proof and glazed shutter) made with galvanised steel colour coated/ powder coated ( Base steel as per IS 513 'D', galvanised as per IS 277 with zinc of 120gm/sqm) with total coating thickness of 0.60mm. ( outside for glazing and inside gauged shutter) Sections for frame should be of 72mmx55mm, section for mullian should be 72mm x 50mm section for shutter frame should be 47mmx 20mm,and section for fixing glass bead should be 12mm x 12mm and section for fly mesh shutter frame should be 40mm x 20mm mesh fixing should be of 18mm x 0.6mm. Stainless steel wire mesh of 0.45mm dia and ave width of aperture 1.4mm shall be used for fly proofing . 4mm thick plain sheet glass to be used for glazing of glazed shutters including 10mm powder coated square saftey grills, locking arrangement and all necessery accessories etc, complete all as specified and directed. Make ELEXIRMET / M/s ASHWANI & SONS

S&F mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Taking down shutter of any description exc 1Sqm and n.exc 2 Sqm each complete all as specified and directed.

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Supply and fix butt hinges of 100mm size extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type C-21 complete all as specified and directed.

S&F 150mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150 mm extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 300 Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

M & L applying new wood surface two coats of synthetic enamel paint over a coat of prink primer on wood or wood based material over 10 cm width or girth including preparation of new wood surface, complete all as specified and directed.

M & L preparation of old painted surfaces of wood and applying one coat of synthetic enamel paint on wood or wood based material over 10 cm width or girth, complete all as specified and directed.

M & L preparation of old painted surfaces of steel and applying one coat of synthetic enamel paint on steel surfaces over 10 cm width or girth, complete all as specified and directed.

M&L for complete removal of existing treatment on wall surfaces and applying two coats of oil bound distemper over a coat of primer over a coat of 3mm thick birla care wall putty etc all as specified and directed.

M & L for complete removal of existing plastered or unplastered decorated surfaces of walls and applying three coat of white wash all as specified and directed.

M & L for preparing old plastered ceiling surfaces and applying two coats of white wash complete all as specified and directed.

M&L for complete removal of existing treatment on wall surfaces and applying two coats of cement base paint over a coat of primer etc all as specified and directed.

M&L 75 mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) in plinth protection laid in alternative bays finished even and smooth without using extra cement including making 10 mm wide grooves to full depth at 3 m interval and at every change of direction and filling the grooves with mixture of bitumen and sand mixed in the ratio of 1:3 by weight and top 10 mm depth sealed with sealing compound grade ‘A’ complete all as complete all as specified and directed.

M&L for designer rubber moulded chequerred cement concrete tiles with mixture of grey and white cemetn in equal porportions with pigments of size 200x 200xx25mm ,300 x 300 x 22mm or 250 x 250 x 22mm thick and set and pointed in neat cement slurry in floors over a screed bed or bedding layer in CM 1:6, 15mm thick for laying floor finishes etc complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness including cover fillets etc complete all as specified and directed.

S & F E Grid suspended false ceiling grid system of size 600 x 600mm with main runner 39x29.7x0.60mm cross tee 29x24.7x0.60mm and wall angle 22.2x22.2x0.50mm ceiling suspended with 2 to 2.5 mm dia GI wire hanger fixed to purlin / truss etc complete (Main runner, cross tee, wall angle of MS galvanised with PPCGS) over the grid providing 4mm thick HPSC pre primed self designer texture non asbestos fibre cement building board fixed to frames etc complete all as specified and and directed.

Supply & fix in repairs Vitreous China Squatting pan, "Orissa" pattern, size 580 x 440 mm white with integral foot rests including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including lime concrete complete including making good to floor, complete all as specified and directed.

S&F PVC (SWR) Nahani /Floor trap, 75 mm dia of out let, plain with grating including jointing to waste pipe with solvent and cement concrete type B1 (1:2:4) & including removing old trap and fixing of stainless steel grating in ground shape etc complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and directed.

S & F 75 mm bore UPVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches including taking down of old pipes, complete all as specified and directed.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches including taking down of old pipes, complete all as specified and directed.

Supply and fix Solid PVC door frame of size 50 x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube, all as specified and shown in Section 8 of MES Schedule Part-II 2010 complete all as specified and directed

Supply and fix Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawings given in Section 8 of MES Schedule Part-II 2010 as applicable complete all as specified and directed.

Dismantling water tanks exc. 500 and n. exc 1000 litres and removing to store, complete all as specified and directed.

S&F rotational moulded polyethyiene water storage tanks triple layered (cylindrical vertical with closed top) of 1000 liters capacity complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 15mm complete all as specified and directed.

S&F Tubes, ‘medium grade’ galvanised, 15 mm bore with all fitting and fixed complete to walls and ceilings or laid in floors etc complete all as specified and directed.

Refixing old steel tubing of 15 mm bore and connections in new or old position (walls, ceilings, floors etc.), complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 20mm complete all as specified and directed.

S&F Tubes, ‘medium grade’ galvanised, 20 mm bore with all fitting and fixed complete to walls and ceilings or laid in floors etc complete all as specified and directed.

Refixing old steel tubing of 20 mm bore and connections in new or old position (walls, ceilings, floors etc.)

S & F in repairs 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed. .(Minimum weight 20mm-210 gms.

S & F in repairs for 20mm gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S&F in repairs CP bib tap 15mm bore fancy type with crutch or butterfly handle, screwed for iron pipe or for unions and fixed complete all as specified and directed.

Supply and fixing pillar taps cast copper alloy fancy type chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm bore fixed in repairs, complete all as specified and directed.

Supply and fixed in repairs stop valve / angle cock fancy type cast copper alloy chromium plated with capstan head serewed down for 15 mm dia iron pipe, complete all as specified and directed.

S&F in repairs chromium plated shower roses 125mm size with or without swivel joint including fixing to steel pipe or union etc.complete all as specified and directed.

S&F PVC connections, 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

Supply & fix in repairs Vitreous China Squatting pan, "Orissa" pattern, size 580 x 440 mm white with integral foot rests including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including lime concrete complete including making good to floor, complete all as specified and directed.

S & F in repairs PVC 10 ltrs capacity symphonic action type low level flushing cistern including flush pipe, cantilever brackets incluiding taking down existing cistern etc complete fixed in repairs complete all as specified and directed.

S&F in repairs vitreous china wash basin, white, flat back, size 580mm X 450mm including CI brackets, 32mm dia brass chromium plated waste fittings with long screwed shanks and fly nuts flanged end bedded in red lead cement and other end fixed with & including cutting for & pinning in end of brackets and 15mm bore pillar tap, cast copper alloy fancy type chromium plated, screwed down high pressure complete all as specified and directed.

S & F in repairs Towel rail 600mm long of brass chromium plated fixed with and including CP brass screws and wooden/plastic cleats. (Minimum weight 190 gms), complete all as specified and directed.

Taking down existing unserviceable point wiring of any description/type/ size of light/fan/tube/power/two way/bell etc on TW batten/conduit including removal of batten / conduit / gutties / wooden boards / switches / sockets / regulators/ light fittings etc and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes complete all as specified and directed.

Material and labour for point wiring complete with stranded copper conductor 1.5 Sqmm (nominal area) PVC insulated unsheathed cable up to 1100 V grade FRLS conforming to IS - 694 multistranded drawn in CONCEALED/SURFACE CONDUIT with new sunk type pressed steel terminal boxes suitable for MODULAR switches including fixing/grouting sunken/ surface as per site requirement covered with suitable modular white cover plate for suitable size for mounting of MODULAR switches, regulators and drawing continuous earth wire with one run of 1.5 Sqmm (nominal area) PVC insulated unsheathed cable up to 1100 V grade FRLS conforming to IS - 694 multistranded copper conductor as earth wire and connecting to common earth dolly and making good the disturbed wall surfaces to match with the existing surfaces complete all as specified and directed for the following :-

(a) One light/ Bell point controlled by one, one way switch 5 amps, SP.

(b) One Ceiling Fan / exhaust fan point controlled by one, one way switch and regulator.

(c) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board.

(d) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(e) One light point controlled by two, two way switch 5 amps, single pole.

Description as per item No.87 here in before but using 2.5 Sqmm single core copper conductor cable of multistranded PVC insulated unsheathed 1100 Volts grade for 3 Pin 15 Amps switch socket combination point on independent board including running of 2.5 Sq mm copper conductor PVC insulated cable as earth continuity conductor, complete all as specified and directed.

Supply and fix MODULAR switch 1 way 6 A, 1 Module capacity 230 volts complete all as specified and directed.

Supply and fix MODULAR socket 5 pin 6 amps 2 MODULE, 230 Volts complete all as specified and directed.

Supply and fix MODULAR socket 6 pin 6/16 amps 2 MODULE, 230 Volts complete all as specified and as directed.

Supply and fix Switch MODULAR 1 WAY 16 amps, 230 Volts complete all as specified and as directed.

Supply and fix electronic ceiling fan regulator MODULAR 5 stepped type heavy duty suitable to work on 230 volts complete all as specified and as directed.

Supply and fix MODULAR bell push of 6 Amps SP, 230 volts AC complete all as specified and directed.

Supply and fix Switch MODULAR two way 6 amps, 230 volts, 1 module complete all as specified and directed.

S & F lamp holder insulated body surface bakelite with back plate suitable for angle / batten fittings fixed with wooden round blocks complete all as specified and directed.

S & F ceiling rose three terminal surface bakelite type AC 50 Hz 230 volts of size 65 x 50 mm complete all as specified and directed.

S & F ding dong Bell AC,230 Volts,single pole, complete all as specified and directed.

S & F wall mounted Indus plus LED Batten,extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver 1x20 w watts, 230 volts, bipin holders, DIFFUSED TYPE connector block, internally pre wired etc with necessary mounting arrangements including all accessories with new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and directed.

Supply anf fix LED security light luminaire fitting of 1x35 watts with deep drawn housing including all accessories with suitable 40 mm dia GI Pipe 0.60 Mtr length fixed on wall with 50x6 mm flat iron, clamps, nuts and bolts complete all as sepcified and directed.

S & F sheet metal enclosure MCB DB SPN 4 way with 200 amps rated bus bar 240 volts double door with magnetic locking system complete all as specified and directed.

S & F sheet metal enclosure MCB DB SPN 8 way with 200 amps rated bus bar 240 volts double door with magnetic locking system complete complete all as specified and directed.

S & F Vertical type TPN DB 4 way double door with incoming MCCB FP 415 volts AC 3 phase 50 Hz, 16KA breaking capacity with fized magnetic setting for current ranging of capacity 63 Amps confirming to IS-13947 (P-2) IEC:947 made out of CRCA sheet housing with powder coating & confirming to IS 13032, IS 8623, BS 5486 accomdated suitably in a MS enclosure weather proof having hinged and robust locking arrangement duly powder coated complete all as specified and directed.

S & F MCB SPN 40 Amps 'B' curve 240 volts for fixing on MCB DB's complete all as specified and directed.

S & F MCB SP 6 to 40 Amps 'B' curve 240 volts for fixing on MCB DB's complete all as specified and directed.

Material and labour for sub main wiring with two runs of single core FRLS PVC insulated, multistranded unsheathed copper conductor cable of size 4 square mm and drawing through PVC conduit of 20mm dia with accessories on surface in wall/roof along with one run of 4 square mm FRLS PVC insulated unsheathed multi stranded 1100 volts grade with copper conductor cable as earth continuity conductor connected to earth and earth dolly, connecting to main board duly making good the disturbed wall surfaces to match with the surroundings complete all as specified and directed. Note: 3 runs of 4 Square mm cable and 1 run of PVC conduit with accessories shall be measured as 1 unit of running metre.

M & L Submain wiring with 2 runs of single core 6 sqmm FRLS PVC insulated unsheated multistranded 1100 volts grade with copper conductor drawn through and including non-metalic rigid PVC conduit concealed and conduit accessories of medium grade not not less than 25 mm dia including one run of single core 6 sqmm FRLS PVC insulated unsheated multistranded 1100 volts grade with copper conductor cable as earth continuty conductor along with the wiring and connected from DB to DB/main board including removing the existing unserviceable submain riwing complete all as specified and as directed. Note: 3 runs of 6 Square mm cable and 1 run of PVC conduit with accessories shall be measured as 1 unit of running metre.

S & F in replacement of Environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge-lit LED luminaire 1 x 9 Watt comprising of high brightness LEDs complete all as specified and directed.

Material and labour for earthing with galvanized mild steel earth plate electrode 60 centimetre x 60 centimetre x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 metres below ground level, the top edge of the earth plate at a depth of not less than 1.5 metres below ground level connected to galvanized iron earth wire of 4 mm dia by means of bolts, nuts and washers made out of GI / steel earth wire protected by GI light grade pipe 15 mm bore, 20mm dia light grade galvanised iron pipe with funnel wire mesh for watering and connecting to main switch board / control board all s shown in electrical plate of SSR Pt - I connected to earthing test point and including testing on completion including taking down old earthing complete all as specified and as directed. NOTE: The unit rate shall also include for excavation, earth work in hard/dense soil, plain cement concrete 1:3:6 type C1 by using 20 mm graded aggregate in pit, 50 mm thick reinforced cement concrete 1:2:4 type B1 using 20 mm graded aggregate cover duly reinforced with 8 mm dia TMT bars @ 100mm centre to centre both ways, galvanised iron funnel with watering pipe, wire mesh, complete.

S&F in replacement of sheet steel MS enclosure earth plug socket 2 pin 20 amps with metal 20 amps with MCB 20 amps complete all as specified and directed.

Supply and fixing ceiling fans 1200mm, aluminium body, power consumption not more than 28W, BEE 5 star rated with BLDC motor, service value greater than 8.40 CMM/W, air deliver minimum 220 CMM, 350 RPM compatible with step regulator for speed control along with down rod, Canopy-2 Nos, electronic 5 step type regulator complete all as specified and directed. Make - Bajaj/Havells/Atomberg Note :- The following documents to be produced while approval :- (i) NABL test report (ii) BEE certificate (iii) BIS certificate (iv) Waranty cetificate for 5 years.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm all as specified and directed.

Supply & fix GI Tubing medium grade of size 40mm da with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. (for hanging fans).

Supply and fix recess mounting with perforated sheet with electronic driver luminaire of Size 600 mm X 600 mm 36 watts LED slim panel with central opal diffuser series mounted in ceiling surfaces including all accessories with new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and directed.

Taking down existing old vintage ceiling/exhaust fans and depositing to MES store yard complete all as specified and directed.

SAI RUPA CONSTRUCTIONS

PAVAN ENTERPRISES

BEEGEE DESIGN SYSTEMS

LAKSHMI ENGINEERS

M/s GM Constructions