REPAIR TO MISC EM ITEMS OF CRANES HOT EOT AND MOTORISED DOOR AT HEMRL UNDER GE RD PASHAN

Amount

Material and labour for Disconnecting and removing damaged gears, bearings etc of main drive gear assembly for servicing, repair including loading / unloading and transporting to nearest work shop including refixing connecting commissioning and testing in position after carry out necessary repair/ replacement and following items complete all as specified and as directed. (i) Supply and fix both side ball bearing with existing size and make as per numbers specified by OEM. Make SKF or equivalent as approved by GE complete all as specified including dismantling taking out old unserviceable bearing gear assembly complete all as specified and as directed. (ii) Repair/Replacement of worn out gear assembly Note : Contractor advised that to visit to site before quoting the rates. (iii) Replacement of both side oil seals & used gear oil of approved make and grade.

Comprehensive maint consisting of normal repairs, Periodical and preventive maint and attending day-to-day break down / complaints of following equipments complete all as specified and directed by Engr-in-charge. (a) Manually operated chain pulley block any type of capacity 0.5 Ton to 5 Ton = 18 nos

Ditto all as per item No. 2 here in before but for (b) Electrically operated over head travelling (EOT) cranes of capacity above 2 Ton up to 5 Ton = 5 nos

Ditto all as per item No. 2 here in before but for (c) Electrically operated over head travelling (EOT) Flame proof cranes of capacity above 2 Ton up to 5 Ton = 12 nos

Ditto all as per item No. 2 here in before but for (d) Electrically operated over head travelling (EOT) Flame proof cranes of capacity above 7.5 Ton up to 20 Ton = 12 nos NOTES FOR SCHEDULE A ITEM No. 2 to 5 (i) Any complaints regarding breakdown must be attended within 24 hours failing to which an amount of Rs 250/- per day on subsequent days will be recovered from RARs. In case of major repair / problems beyond the scope of contract , contractor has to intimate the department within 48 hours failing to which a recovery as per clauses mentioned above will be affected. (ii) Quoted rates are deemed to be inclusive of the cost of all materials and labour required for dismantling and assembling of equipment in whole as a part there of and cost of minor spares and material required such as grease, cotton waste,lugs,nut bolts,washers, insulation tapes etc (iii) Major defects such as Long Traval /Cross Traval and hoist motor rewinding, replacment of faulty bearings,shaft and gear assy / VFD failure / Soft starter electronic cards etc does not includes in this cost. In case of major problems beyond the scope of contract the same has to intimate to the department within 48 hours failing to which are recovery as per clauses mentioned above in note (i) will be affected. (iv) Materials like MCCBs, shoe brakes, brake drums, contractors relays, steel wire ropes, etc. required for repairing will be supplied and paid separately under relevant items of schedule supply only . (v) The quoted rate include the cleaning of cranes of diff capacity, cleaning of respective tracks and busbars. (vi) repair/servicing to crane LT panels, thruster, brakes, electric motors,gresing of steel ropes,limit switches,pendent push buttons complete on monthly basis. (vii) Quoted rate is deemed to be inclusive all the clothing, safty equipment and other T & P required for carrying out the repairs / maintence. The contractor has to liase with the department in case of taking of electric shutdown of each machinery and has to make the machinery functional of the carrying out maintenance.

Testing (full load test, deflection test, capacity test, speed test and break test) and serviceability checking of each cranes and hoist by authorized person in presence of Engr-in-Charge, JE (E/M) and User's representative and test certificate with list of defects if any to be produced in duplicate. The capacities of cranes, hoists to be tested are as under :- (a) Manually operated chain pulley block any type of capacity 1.5 Ton to 5 Ton - 18 Nos

Ditto all as per item No. 6 here in before but for (c) Electrically operated over head travelling (EOT) cranes of capacity above 2 Ton up to 5 Ton - 5 Nos

Ditto all as per item No. 6 here in before but for (d) Electrically operated over head travelling (EOT) Flame proof cranes of capacity above 2 Ton up to 5 Ton - 12 Nos

Ditto all as per item No. 6 here in before but for (d) Electrically operated over head travelling (EOT) Flame proof cranes of capacity above 7.5 Ton up to 20 Ton - 12 Nos NOTES FOR SCHEDULE A ITEM No. 6 to 9 (i) Loads required for testing to be arranged by contractor (ii) The Load test to be carried out by recognized / authorized Govt Agencies in the presence of Engr-in-charge & Users rep. (iii) The Load test report as per Performa at 100% load for all motions from recognized persons as specified in Note (ii) above duly signed. (iv) Load testing is inclusive of shifting / transporting the load place to place, unloading will be arranged by the contractor including required ropes, man power etc., for handling the load.

Supply and fix in repairs of spare parts suitable for the HOT / EOT/ EOT (Flameproof) cranes. (a) Power contactors 3 pole with NO + NC up to 32 Amps, MNX type complete all as specified and as directed.

(b) Power contactors 3 pole with NO + NC 32 amps , MNX type complete all as specified and as directed.

(c) Power contactors 3 pole with NO + NC 40 amps, MNX type complete all as specified and as directed.

(d) Power contactors 3 pole with NO + NC 70 amps, MNX type complete all as specified and as directed.

(e) Thermal Over load relay 0.9- 1.5 Amps, MN2 type complete all as specified and as directed.

(f) Thermal Over load relay 1.4 - 2.3 Amps, MN2 type complete all as specified and as directed.

(g) Thermal Over load relay 6 - 10 Amps, MN2 type complete all as specified and as directed.

(h) Thermal Over load relay 9 -15 Amps, MN2 type complete all as specified and as directed.

(j) Galvanised Steel wire rope conforming to IS 2266:2002 of nominal diameter of 8 mm having 6 x 19 M (12/6-1) multi stranded construction steel core CRW grade 1570, having mass 24.4 kg / 100 m with breaking capacity 33 KN complete all as specified and as directed. Make:- Usha Martin / Bombay Foot / National or as used or recommended by OEM

(k) Galvanised Steel wire rope conforming to IS 2266:2002 of nominal diameter of 10 mm having 6 x 19 M (12/6-1) multi stranded construction steel core CRW grade 1570, having mass 38.1 kg / 100 m with breaking capacity 52 KN complete all as specified and as directed. Make:- Usha Martin / Bombay Foot / National or as used or recommended by OEM

(l) Galvanised Steel wire rope conforming to IS 2266:2002 of nominal diameter of 12 mm having 6 x 19 M (12/6-1) multi stranded construction steel core CRW grade 1570, having mass 54.8 kg / 100 m with breaking capacity 75 KN complete all as specified and as directed. Make:- Usha Martin / Bombay Foot / National or as used or recommended by OEM

(m) Galvanised Steel wire rope conforming to IS 2266:2002 of nominal diameter of 18 mm having 6 x 19 M (12/6-1) multi stranded construction steel core CRW grade 1570, having mass 123 kg / 100 m with breaking capacity 169 KN complete all as specified and as directed. Make:- Usha Martin / Bombay Foot / National or as used or recommended by OEM

(n) PVC Coated and PVC insulated copper conductor multi stranded cores 1.5 sqmm 19 core complete all as specified and as directed.

(o) PVC Coated and PVC insulated copper conductor multi stranded cores 1.5 sqmm 12 core complete all as specified and as directed.

(p) PVC Coated and PVC insulated copper conductor multi stranded cores 2.5 sqmm 8 core complete all as specified and as directed.

(q) PVC Coated and PVC insulated copper conductor multi stranded cores 2.5 sqmm 12 core complete all as specified and as directed.

(r) PVC Coated and PVC insulated copper conductor multi stranded cores 4 sqmm 4 core complete all as specified and as directed.

(s) PVC Coated and PVC insulated copper conductor multi stranded cores 6 sqmm 4 core complete all as specified and as directed.

(t) PVC Coated and PVC insulated copper conductor multi stranded cores10 sqmm 4 core complete all as specified and as directed.

(u) Crane gear oil EP -320 thick level complete all as specified and as directed.

(v) Crane thruster oil / break oil (hydraulic oil) ISO68 complete all as specified and as directed.

(w) Hydraulic brake thruster (Flameproof) of capacity 18 Kgs incl first fill of hydraulic oil (size 100 mm to 300 mm) complete all as specified and as directed.

(x) Hydraulic brake thruster of capacity 18 Kgs incl first fill of hydraulic oil (size 100 mm to 300 mm) complete all as specified and as directed.

(y) Heavy duty cast iron break shoe treated with fabric lining with aluminium rivets of LT / CT/hoist brake drum of 100 mm dia complete all as specified and as directed.

(z) Heavy duty cast iron break shoe treated with fabric lining with aluminium rivets of LT / CT/hoist brake drum of 150 mm dia (thickness 8 to 10 mm) complete all as specified and as directed.

(aa) Heavy duty cast iron break shoe treated with fabric lining with aluminium rivets of LT / CT/hoist brake drum of 200 mm dia (thickness 8 to 10 mm) complete all as specified and as directed.

(ab) Heavy duty cast iron break shoe treated with fabric lining with aluminium rivets of LT / CT/hoist brake drum of 250 mm dia (thickness 8 to 10 mm) complete all as specified and as directed.

(ac)Rewinding of control transformer 415/230/110 Volts complete all as specified and as directed.

(ad) Limit switch Limit switch suitable for 2 to 15 Ton assembly complete all as specified and as directed.

(ae) Flame Proof Limit switch Limit switch suitable for 2 to 10Ton assembly complete all as specified and as directed.

(af) Push button 1 NO + 1 NC complete all as specified and as directed.

(ag) Electronic timer with range 03 sec to 30 sec for control panels of EOT cranes complete all as specified and as directed.

(ah) Electronic timer with range 12 sec to 120 sec for control panels of EOT cranes complete all as specified and as directed.

(aj) Single phase preventer complete all as specified and as directed.

(ak) PVC cable carrier /Cable Trolley size P-20 suitable for carrying cable of size up to 4 core 4 sqmm, complete all as specified and as directed.

(al) PVC cable carrier /Cable Trolley size P-50 suitable for carrying cables of sizes up to 24 core 15 sqmm & 4 Core 10 Sqmm, complete all as specified and as directed.

(am) Neon indiator lamp 24 volts complete all as specified and as directed.

(an) Carbon Brush of 25mm x 25 mm size complete all as specified and as directed.

Supply only Push button Pendents 10 way for cranes including suitable size cable all as per sample and details in complete all as specified and directed.

Dismantlling and taking down brake drum of size 100mm dia by disconnecting it from brake drum assy and taking it to auth wksp for sanding the plain surface in order to make grip for brake shoe for holding / releasing the brake of the crane and fixing it at the same position complete all as specified and as directed by Engr-in-charge.

Dismantlling and taking down brake drum of size 150mm dia by disconnecting it from brake drum assy and taking it to auth wksp for sanding the plain surface in order to make grip for brake shoe for holding / releasing the brake of the crane and fixing it at the same position complete all as specified and as directed by engr-in-charge.

Dismantlling and taking down brake drum of size 200mm dia by disconnecting it from brake drum assy and taking it to auth wksp for sanding the plain surface in order to make grip for brake shoe for holding / releasing the brake of the crane and fixing it at the same position complete all as specified and as directed by Engr-in-charge.

Dismantlling and taking down brake drum of size 250mm dia by disconnecting it from brake drum assy and taking it to auth wksp for sanding the plain surface in order to make grip for brake shoe for holding / releasing the brake of the crane and fixing it at the same position complete all as specified and as directed by Engr-in-charge. Note for Item Ser No 49.00 to 52.00 :- (i) The quoted rate includes the cost of transport drum to workshop, sanding and back only, labour will labour charges included in Item No 1 above. (ii) Contractor should visit the site before quoteing the tender to know the scope of work. (iii) Contractor should provide necessary T&P, safety eqipments for execution of work at no extra cost.

Dismantling / Removing existing control & power wiring of long travel/cross travel/main hoist/auxilarry hoist control Panel wiring of EOT Crane 5 to 10 ton and rewiring with PVC insulated copper wire 1.5 /2.5 /4 /6 Sq mm for control & 10/16 Sq. mm for power wiring for proper sequential working of contactors with delay timer, over load relay,mccb,mcb etc of slip ring motor of diff capacity by making proper connections to contactors, relays, fuses, mccb,mcb incl testing commissioning complete all as specified and as directed. Note:- (i) Material such as PVC channels, lugs, terminals dinrails connectors, welding work for panel wiring on Eot crane will be include in above rates. (ii) The quoted rate include the cost of painting of existing control panel with two coats of existing coloured paints and any adition/alteration in the existing control panel complete all as directed by Engr-in-charge. (iii) Required components such as PVC copper cable, MCCB's, MCB's, HRC fuse, power contactors, relays, timers, Single phase preventor , push buttons will measured and paid separetly under relevent item. (iv) The work is to be done in such a manner that it should not hammper the working schedule of the user. (v) Contractor should visit the site before quoting the rates as the work have to carried out at the height approx 10 - 15 metre. (vi) Control wiring should be done in such a manner to meet the logic and operation.Suitable skilled rep shall be deputed to do the same. Necessary test reports to be submitted after completion of work. (vii) Contractor should provide skilled supervisor and necessary safety equipments, T&P for execution of work.

Supply and fix in repairs Flameproof / Weatherproof LED Well Glass Light Fitting suitable for 45 Watt, body made out of aluminium alloy LM -6 body epoxy painted with wire guard relfector, flameproof Heat Resistant Clear Toughened ‘Type‐ A’ with LED COB / SMD (Bridge, Cree, Citizen) including suitable electronic including necessary fixing arrangments and connecting up complete all as specified and directed by Engr-in charge. Make:- Shyaam Switchgear Cat Part No SSPL/1233 / Flexpro / Baliga

Supply and fix in repairs Flameproof / Weatherproof LED Well Glass Light Fitting suitable for 90 Watt, body made out of aluminium alloy LM -6 body epoxy painted with wire guard relfector, flameproof Heat Resistant Clear Toughened ‘Type‐ A’ with LED COB / SMD (Bridge, Cree, Citizen) including suitable electronic including necessary fixing arrangments and connecting up complete all as specified and directed by Engr-in charge. Make:- Shyaam Switchgear Cat Part No SSPL/1251 / Flexpro / Baliga

Taking down control panel of any capacity of EOT crane, modification by replcaing all relays, contactor & other elctrical items with new wiring of control panel with variable voltage variable frequency drive (VVVFD) suitable for 3 phase electric motor used for EOT crane gear working on 3 phase 380- 480V power supply, so as to run all the motors of respective motions of EOT crane through VVVF drive and for smooth functioning of EOT crane through VVVFD drive and for smooth functioning of EOT cranes complete all as specified and as directed. Make :- Mitsubishi/ Yaskawa Electric Corporation / CG/ ABB / L&T or as per installed on site as recommended by OEM.

Dismantling after disconnecting of all electric connection of soft starter of any make and sent to authorised/manufacturer workshop for servicing, repair & testing and replacement of all unserviceable parts whichever required to make it serviceable in all respect including programmeable card as per recommendation of manufacturer and will be brought back to same postion and refixing/reconnection of electric connection on its original position and testing and commissioning with full load complete all as specified and directed by Engr-in-Charge

Material and labour for disconnecting from main supply, Dismantling and taking down existing reduction gear box for with device from EOT/ HOT crane of 2 To 10 Ton Capacity hoist /CT/ LT motion traverse for carry out replacement of following U/S Parts/Carry out Misc repairs to gear box, oil leakage and refining the gear box after checking alignment of brake drum & motor, motor & gear box, in existing position, complete all as specified and as directed by the Engr-in-Charge. (a) Replacing the worn out shaft seals & bearing. (b) Replacement of internal cover gasket. (c) U/S Gear coupling with nuts & bolts complete. (d) Replacement of worn out driving/ driven keys, gaskets of capacity not exc 10 ton complete all as specified and as directed by Engr-in-charge. Note : (a) All Minor spares including gaskets, keys, Nuts, Bolts deemed to be included in above quoted rates. (b) Spares like driving / driven gears, oil / Shaft seal, bearings will be measured and paid separately under relevant item of sch 'A'.

Supply only driving / driven gear of size suitable for gear box of crane cap 2 Tonne to 10 Tonne complete all as specified and as directed.

Supply only shaft seal for gear box of crane cap 2 Tonne to 10 Ton complete all as specified and as directed.

Supply only coupling for gear box of crane cap 2 Tonne to 10 Ton complete all as specified and as directed.

Disconnecting the electrical and mechanical connection of burnt electrical motors transporting from the site / location to work shop and back. Rewinding of electrical motors by dismantling and removing the burnt cut copper winding wire cleaning the slots of stator with petrol and brushes winding polyester based super enameled copper wire of same gauge of original one with proper class of insulation including varnishing and heating the coil and remove air bubbles complete stator/rooter after rewinding reassembling all parts including reinstalling connection to original position and testing on full load complete all as specified and as directed by Engineer-in- charge for different capacity of motor as per following :- a) 1 HP to 2 HP

b) above 3 HP but up to 5 HP

c) above 5 HP but up to 7.5 HP

d) above 7.5 HP but up to 10 HP

Material and labour for dismantling, taking down for repair of motor for servicing replacement of unserviceable bearing, seal, bush complete dismantling of brake drum, motor, coupling etc and refixing same after repair work for hoist, CT (cross travel) and LT (long travel) motion motor, complete all as specified and directed by Engr-in-charge :- a) 1 HP to 2 HP

b) above 3 HP but up to 5 HP

c) above 5 HP but up to 7.5 HP

d) above 7.5 HP but up to 10 HP Note: (a) All Minor spares including gaskets, keys, Nuts, Bolts included in above quoted rates. (b) Spares like bearings, fan blade will be measured and paid separately under relevant item of sch A

Supply and fix in repair for following bearing as per numbers given below. Make : SKF or Equivalent as approved by GE and complete all as specified Including dismantling taking out old unserviceable bearing from crane complete all as specified and directed. a) 6208 Z or as per existing make complete all as specified and directed.

b) 6310 Z or as per existing make complete all as specified and as directed.

c) 6008 Z or as per existing make complete all as specified and as directed.

d) 22209 E or as per existing make complete all as specified and as directed.

Dismantling of existing unserviceable male-female combination of FLP socket from existing position and replacement of new flame proof socket / switch socket and plug combined in LM 6 body 4P +Earth of 32 A rating 3 Ph 500V suitable for 2 to 20Ton capacity EOT crane and refining the same complete all as specified and as directed by Engr-in-Charge.

Supply and fix in repair MCCB 63 amps 16 KA capacity 4 pole ,at 415 Volt AC 50 Hz Adjustable thermal magnetic release including suitable arrangement to existing LT panel for proper seating/operation complete all as specified and as directed.

Supply and fix in repair MCCB 100 Amps 16 KA capacity 3 pole ,at 415 Volt AC 50 Hz Adjustable thermal magnetic release including suitable arrangement to existing LT panel for proper seating/operation complete all as specified and as directed.

Supply and fix in repair MCCB 200 Amps 36 KA capacity 3 pole ,at 415 Volt AC 50 Hz Adjustable thermal magnetic release including suitable arrangement to existing LT panel for proper seating/operation complete all as specified and as directed.

Supply and fix in repair MCCB 250 Amps 36 KA capacity 3 pole at 415 Volt AC 50 Hz Adjustable thermal magnetic release including suitable arrangement to existing LT panel for proper seating/operation complete all as specified and directed.

Supply and fix in repair of MCCB 400 Amps 36 KA capacity 4 pole at 415 Volt AC 50 Hz Adjustable thermal magnetic release including suitable arrangement to existing LT panel for proper seating/operation complete all as specified and directed.

Supply and fix in repair MCCB 630 Amps 36 KA capacity 4 pole at 415 Volt AC 50 Hz Adjustable thermal magnetic release including suitable arrangement to existing LT panel for proper seating/operation complete all as specified and directed.

Supply and fix in repair MCB TPN 40 Amps to 63 Amp 415 Volt complete all as specified and as directed.

Supply and fix in repair MCB SP 'C' series 6 Amps to 32 Amps 240 V complete all as specified and as directed.

Supply and fix in repair MCB SP 'C' series 40 Amps to 63 Amps 240 V complete all as specified and as directed.

Supply and fix in repair MCCB enclosure box for 3P MCCB , in built neutral link for TPN system, IK 08 and IP 30 protection suitable size for mounting 160 A to 250 A MCCB, 50KA complete all as specified and directed.

Material and labour in repair for special factory made earthing electrode comprising of hot dpped galvaized MS flat inserted in to GI pipe of 88mm bore (outer), 3metre length, filled with non magnetic anti corrosive material specially developed for ground resistance enhancement power around the electrode to retain moisture conforming to IS 3043 including necessary boring in ground of 150 mm dia in any type of strata connecting to test point all as specified and directed (the earth resistance shall be less than 1 ohm complete all as specified and directed. Contractor shall improve the earthing resistance within the permissible limit without any extra cost. "MAKE :- Fast Electrode / ASHLOK/ U-PROTEC EARTHING PVT. LTD. Note:-GI earthing pipe should have successfully tested for salt spray test (corrosion test) Certificate for minimum 500 hours. The Earthing Electrode should have a GTP & Drawing approval from MSEDCL infra Project. The Earthing Electrode should be tested in MSME. Any one such Earthing Electrode should have successfully type test certification by CPRI (Central Power Research Institute, Govt of India) for the Short Time current at 43 kA rms for 1 Sec; with initial peak of 90.12 kA. The rated voltage for testing in CPRI should be 400 V at rated current of 10kA. The Earth Enhancing Compound should have Test certification from NABL accredited Lab. It should be tested as per IS 1350/ AHPA guideline’s. The pH value of Compound should be 7.59, Moisture % by mass should be 8.91& Solubility in 1:1 HCL should be 32.29 %. The Compound should be tested ELV Test as per protocol IEC 62321/111/54/CDV/ICP-OES for contain of Lead (23.0 ppm), Cadmium (15.0ppm), Mercury (Below Detection Level) & Hexa-chromium(Below Detection Level)

Material and labour in repair for Earth continutity conductor or main earthing lead fixed to wall /burried in ground /drawn in pipes or fixed to poles or any other indicated situvations for loop earthing of GI strips of size 32mm x 6 mm including connecting complete all as specified and as directed.

Material and labour for Cleaning total structure of crane 5/15 Ton, Remove all grease & Oil from crane parts, preparation of old painted steel/CI surface of crane (i.e motor panel board, handle cross arms, Horizontal Arms, grills, MS Plate, ladder etc complete and applying spray painting to crane with superior quality paints with one final coat over one initial coat complete all as specified and as directed by Engr-in-charge.

Material and labour for Cleaning total structure of crane 2/3 Ton, Remove all grease & Oil from crane parts, preparation of old painted steel/CI surface of crane (i.e motor panel board, handle cross arms, Horizontal Arms, grills, MS Plate, ladder etc complete applying spray painting to crane with superior quality paints with one final coat over one initial coat complete all as specified and as directed by Engr-in-charge.

Material and labour for Cleaning total structure of flame proof crane upto 5 Ton, Remove all grease & Oil from crane parts, preparation of old painted steel/CI surface of crane (i.e motor panel board, handle cross arms, Horizontal Arms, grills, MS Plate, ladder etc complete applying spray painting to crane with superior quality flameproof paints with one final coat over one initial coat complete all as specified and as directed by Engr-in-charge.

Material and labour for Cleaning total structure of flame proof crane 10 to 20 Ton, Remove all grease & Oil from crane parts, preparation of old painted steel/CI surface of crane (i.e motor panel board, handle cross arms, Horizontal Arms, grills, MS Plate, ladder etc complete applying spray painting to crane with superior quality flameproof paints with one final coat over one initial coat complete all as specified and as directed by Engr-in-charge.

Material and labour for servicing /overhauling of electricaly/mannually operated sliding steel doors of any size by applying grease on movable parts and replacement of the damaged parts if any required for smooth operations including cleaning of track and removal of mud / deposites and painting of steel doors with existing colour synthetic enemelled paint single coat on old surface installed in the various processing buildings/ Magazine and other technical buildings as mentioned below complete all as specified and as directed . Note :- Spare/wornout parts required for replacement will be measured as supply only.

Material and labour for servicing /overhauling of gear boxes of Electrically operated door located at various locations including replacement of wornout spare parts gear if any required for smooth operation complete all as specified and directed by Engineer-in-Charge. Note :- Spare parts required for replacement will be measured as suppy only.

Supply only ball bearing No. 6304 complete all as specified and as directed.

Supply only ball bearing No. 6311 complete all as specified and as directed.

Supply only ball bearing No. 4308 /6406 complete all as specified and as directed.

Supply only Gear oil Multigrade 80W-90 complete all as specified and as directed.

Supply only worm gear (top gear) to operate rolling shutter complete all as specified and as directed.

Supply only shaft to operate worm gear complete all as specified and as directed.

Supply only bowel gear (bottom gear) to operate rolling shutter complete all as specified and as directed.

Supply only worm shaft gear complete all as specified and as directed.

Supply only oil seal complete all as specified and as directed.

M/S. Niksun Electro-Infra Private Limited