Construction of Medical College hostel, Residence for student/ faculty at Udhampur (Baili village) (Boys Hostel, Girls Hostel, Canteen, Gym, Nurse Qtr., Residential Type-I, Residential Type-II, Principal Residence Type-III, Residential Type-IV, Park

Amount

SUB HEAD - I: CIVIL WORK

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -All kinds of soil.

Earth work in bulk excavation for foundation, footing by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m which includes surface dressing and Contours also as directed by Engineer-in-Charge.

Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge in All kinds of soil.

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 meters in All kinds of soil.

Extra for every additional lift of 1.5 M or part therefore in all kinds of soil including the disposal of the same out side the municipal limits.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level in 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate) 40mm nominal size crushed.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-incharge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable separately. All works upto plinth level.

Providing and laying in position machine batched and machine mixed design mix M-30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-incharge. Note: - Cement in this item is @ 340 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable separately. All works upto plinth level.plinth level

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-incharge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable separately.All works above plinth level upto floor V level.

Extra for providing richer mixes at all floor levels. Note:- Excess/ less cement over the specified cement content used is payable/ recoverable separately. Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum)

Providing and laying in position cement concrete of 1:3:6 grade (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20mm nominal size) excluding the cost of centering and shuttering. All work upto plinth level.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etc upto floor V level, including curing but excluding the cost of centring, shuttering and finishing with.1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 75 upto plinth level in cement mortar 1:4 (1 cement : 4 fine sand).

Providing and laying DPC 50mm thick in 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size crusher aggregate).

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for underground structures as directed by Engineer-in-Charge and consisting of : i) 1st layer coarse sand) mixed with water proofing compound conforming to stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3of 22 mm to 25 mm thick approved and specified rough IS:2645 in the recommended proportion over the levelling course (levelling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound.ii) 2nd layer of 25mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with waterproofing compound in recommended proportions. iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer. Using rough kota stone.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-Charge: Using rough kota stone.

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 75 in super structure in cement mortar 1:6 (1 cement : 6 fine sand).

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level.

Half brick masonry with bricks of class designation 75 in foundation, plinth and superstructure upto floor V-level in cement mortar 1:4 (1 cement : 4 coarse sand).

Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry (with F.P.S bricks).

Applying a coat of residual petroleum bitumen of grade VG-10 of approved quality using 1.7 kg per square meter on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete TMT bars.

Centering and shuttering including strutting, propping etc. and removal of form work for :-

Foundations, footings, bases of columns.

Retaining walls, return walls, wall (any thickness) including attached pilasters, buttresses, plinth and string courses fillets etc.

Columns, pillars, piers, abutments, posts and struts.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Suspended floors, roofs, landings, balconies and access platforms.

Edges of slabs and breaks in floors and walls upto 20cm wide.

Weather shade, chajjas, corbels etc. including edges.

Stairs (excluding landings) except spiral stair cases.

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentring at all levels, over a height of 3.5m, for every additional height of 1 mtr. of part thereof (Plan area to be measured). Suspended floors, roofs landing, beams and balconies (Plan area to be measured).

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Supplying and filling in plinth with fine sand under floors including, watering, ramming consolidating and dressing complete.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded brick aggregate 40mm nominal size) in R/Wall/Return Wall, columns etc. excluding the cost of centering and shuttering, all works upto floor V level.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded brick aggregate 40 mm nominal size below flooring, retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etc upto floor V level, including curing but excluding the cost of centring, shuttering and finishing.

6mm thick cement plaster to ceiling of mix 1:3 (1 cement : 3 fine sand).

15mm cement plaster on the rough side of single or half brick wall of mix in 1:6 (1 cement : 6 fine sand).

15mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement : 4 fine sand).

12mm cement plaster of mix 1:6 (1 cement : 6 fine sand).

15mm cement plaster 1:4 (1 cement : 4 coarse sand) finished with a floating cost of neat cement on the rough side of single or half brick wall.

18mm thick moulded cement mortar band in two coats under layer 12mm thick with cement mortar 1:5 (1 cement : 5 fine sand) top layer 6mm thick with cement mortar 1:4 (1 cement : 4 fine sand) for 4cm width.

Extra for plastering exterior walls of the height more than 10 Mtrs from ground level for every additional height of 3 Mtrs or part thereof.

Add or deduct for plaster drip coarse / groove in plastered surface of moulding to RCC projections.

Making of grove 12mm x 10mm between brick and RCC.

Providing and laying Double Charged vitrified floor tiles in 600x1200mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make of Somany, Kajaria and Johnson in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.

Providing and laying glossy finished full-body vitrified premium quality floor tiles of 60x60cm sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622 of approved make of Somany, Kajaria and Johnson make in colours and shade Ethnic-Berlinetta White, Crown White, Dacia White, Dacia Green, Dacia Pink, Dacia Ivory, Dacia Grey, Dacia Brown, Dacia Pearl, Dezzling White, Evalia, S&P Grey, S&P Brown, Ultra White, Haze Grey and Border of Royale- Crown Mint, Crown Pink, Crown Snow, Micra Brown and Radiant- Lawrence Gold, Lawrence Bianco, Lawrence Grigio, Lawernce Moka, Techstone and Geostone series laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with matching Epoxy etc. complete.

Providing and fixing Ist quality ceramic glazed tiles conforming to IS : 15622 of minimum thickness 5mm thick of approved make like Somany,Kajaria and Johnson make in colour and shades Glosstra Plus-Lithor Light, Lithor Dark, Canica Light, Canica Dark, Gentil Light, Gentil Dark, Sterno light, Sterno Dark, Marfil Beige, Cream Glossy, Arian Bianco, Bello Mint Dark, Camia Light, Verde Dark, Fabro Brown Dark, Marina Blue, Strix Grey Vivo Crema, Vivo Mushroom of size 300x600mm as approved by Engineer in charge in skirting, risers of steps and dodos and verticle surfaceover 12mm thick bed of cement mortar 1:3 (1cement : 3coarse sand) and jointing with grey cement slurry @ 3.3Kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing ceramic glazed floor tiles (non-skidding) 300x300mm (thickness to be specified by the manufactures) of Ist quality conforming to IS : 13755 of Somay,Kajaria and Johnson make in colour such as white, Ivory, Grey, Fume Red, Brown laid on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete.

Providing and laying 18mm thick Granite of any colour and shade (area of slab over 0.5 Sqm) gang saw cut mirror polished (pre moulded and pre polished), machine cut for Floors and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels.

40mm thick Agra Red stone slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab, complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)

Kota stone slab flooring 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab, incl polishing rubbing, plishing and rubbung,complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and laying 16mm thick Granite of any colour and shade (area of slab over 0.5 Sqm) gang saw cut mirror polished (pre moulded and pre polished), machine cut for Floors and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels.

Providing and laying 18mm thick Granite of any colour and shade (area of slab upto 0.5 Sqm) gang saw cut flamed (pre moulded and pre polished), machine cut for stairs steps and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels.

Extra for providing edge moulding to 18mm thick Granite stone counters, Vanities etc. over item No.44 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge

Extra for providing opening of required size and shape for wash basins/kitchen sink in kitchen platform, vanity counters and similar location in marble / stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Cement concrete flooring 1:2:4 finished with a floating coat of neat cement including cement slurry, but excluding the coat of nosing of steps etc. complete 50mm thick with 20mm nominal size of stone aggregate.

Cement plaster skirting (upto 30cm height) with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement 18mm thick.

Providing and laying integral cement based water proofing treatment including preparation of surfaces as required for treatment of roofs, balconies, terraces etc. (Make Armocreate of SWC Chryso France) consisting of (a) applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks / brick bats 25mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining was upto 300mm height including rounding of junction of walls and slaps. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge. (iv) Finishing the surface with 20mm thick joint less cement mortar of mix 1: 4 admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge including laying glass fiber cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300mm / sq 3mm deep. (e) The whole terrace so finished shall be flooded with water far a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by Engineer-in-charge. With average thickness of 120mm and minimum thickness at khurras as 65mm.

Providing and laying water proofing treatment (Make Armocreate of SWC Chryso France) to vertical and horizontal surface of depressed portions of W.C., kitchen and the consisting of (i) Ist course of applying cement slurry @ 4.4 kg /sqm mixed with water proofing compound conforming to IS : 2645 in recommended proportions including rounding of junctions of vertical and horizontal surface. (ii) IInd course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportions including rounding of junctions of vertical and horizontal surface. (iii) III course of applying blown or / residual bitumen applied hot at 1.7 kg per sqm of area. (iv) Ivth course of 400 micron thick PVC sheet (Overlaps at joints of PVC sheet should be 100mm wide and pasted to each other with bitumen @ 1.7 kg/sqm.

Making plinth protection 50mm thick cement concrete 1:3:6 (1 cement : 3 course sand : 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth crushed and curing complete.

Brick edging 7 cm wide 11.4cm deep to plinth protection with bricks of class designation 75mm including grouting with cement mortar 1:4 (1 cement : 4 fine sand) and curing complete.

Providing sal wood work in frames of door and windows,Clerestory windows and other frames wrought framed and fixed in position sal wood

Providing and fixing 35mm thick wire gauze shutters using galvanized M.S. wire gauge of average width for aperture 1.4mm in both direction with wire of dia 0.63mm for doors, windows and clerestory windows with hinges and necessary screws in second class deodar wood.

Providing and fixing of glass panes weighing 13.75 kg/sqm (5.5mm thick) with deodar wood fillets.

Applying priming coat with ready mixed pink or grey of primer of approved brand and manufacture on wood work (hard and soft wood).

Painting with synthetic enamel paint of approved brand and manufacture to give and even shade two or more coats on new work (Wood work).

Painting with ready mixed synthetic enamel paint of approved brand and manufacture in all shades to give an even shade (two or more coats) on new steel work.

Providing and fixing M.S grills of required pattern in frames of windows etc. with M.S flats, square or round bars etc. including priming coat with approve steel primer all complete (fixed to openings/wooden frames with rawl plugs, screws etc.).

Providing and fixing of 18 Gauge M.S. Sheet Wadrobe finish with Duco-paint inside and outside of the wadrobe with locks, tower bolts, cloth hanging rail etc. As per the Architect / Engineer-in-charge.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows of Second class deodar wood fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge including all necessary fitting * Butt hinges and necessary screws of Make Arch, Kitch, Blum complete job.

Providing and fixing of block door shutters 37mm thick in pine wood filling and finished with 1mm thick laminated on both sides (laminate Make:- Green, Archidply). Door held with 4 No. stainless steel but hinges of size 100mm X 50mm X 2mm of make Kitch, Arch, Blum with necessary stainless screws as per directions of Engineer-in-charge with teak wood beading on periphery of the door complete job.

Providing and fixing Mortise lock with liver type handle ofStainless Steel (S.S 304 grade) with corrosion resistant mechanism design as per Engineer-in-charge . Make:- Godrej, Link, Kitch, Arch.

Extra for providing heavy sheet float glass panes instead of ordinary float glass in glazed doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured) 5.0mm thick instead of 4 mm thick

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions at top, bottom and sides with required PVC / neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge (glazing and panelling to be paid for separately) (2.60mm or 12 gauge).

For fixed portion using Powder coated aluminium (minimum thickness of powder coated 50 microns).

For shutters of doors, windows and ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminium (minimum thickness of powder coated 50 microns). (2.60mm or 12 gauge).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partition etc. with PVC / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item). With glass panes of 5 mm thickness (weight not less than 13.75 kg/sqm). (Saint Govin/Modi Gaurd make)

Providing and fixing 12mm thick prelaminated three layer medium density (exterior grade) particle board Grade-I, Type-II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows shutters and partition frames with C.P brass / stainless screws etc. compete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, having brand logo embossed on the body/plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineerin- plate etc. complete as per the direction of Engineer-in-charge with brass cover plate minimum 1.25 mm thickness.

Providing and fixing fly proof stainless steel grade 304 wire gauze with 0.5mm dia wire and 1.4mm wide aperture in aluminium door, window, ventilator shutters and partition etc. with PVC / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item).

Providing and fixing aluminium tower bolts ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete.

Providing and fixing aluminium sliding door bolts ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. 300x16mm.

Providing and fixing aluminium handles ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete.

Providing and fixing aluminium casement stays ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete.

Providing and fixing aluminium hanging floor door stopper ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. Twin rubber stopper.

Providing and fixing aluminium pull bolt lock anodized ISI marked (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary bolt nuts and washers etc. complete.

Providing and fixing 100 mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Steel section welded in built up section for Grills/frame work incl. cutting hosting , fixing in position and applying a priming coat of approved stell primer a priming coats of approved stell primer using structural steel etc as reqd.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc, including welded, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary steel brackets and stainless steel nuts and bolts complete on wall with suitable arrangement as per approval of Engineer-in-charge.

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture including providing and fixing top and bottom pivot and spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (door handle, lock and stopper etc. to be paid separately). (Saint Govin /Modi Gaurd)

Providing and fixing anodized aluminium grill (anodized transparent or dyed to required shade according to IS : 1868 minimum anodic coating of Grade AC 15 of approved design / pattern, with approved standard section and fixing to the existing windows frame with C.P. brass/stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodized aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (only weight of grill to be measured for payment).

Filling the gap in between aluminium frame and adjacent RCC /Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete upto 5mm depth and 5mm width

Providing and fixing structural glazing on required portion of the building with aluminium section (12 gauze using 5.5mm toughen glass with all necessary fittings complete job) as per direction of Engineer-in-charge (AIS CHROMA – VLT – 23, u.v-4, SHGC-26, U Value-3.7.

Providing and fixing false ceiling (ceiling tiles mineral fibre and ceiling 8821 of diamond make) at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25mm widex 1.6mm thick with flanges of 27mm and 37mm at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastner 12.5mm dia x 40mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts and bolts of required size and other end of angle hanger fixed with G.I channels 45x15x0.9mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick buttom wedge of 80mm with tapered flanges of 26 mm each having clips of 10.5mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall / partition with the help of rawl plugs at 450mm centre to centre, with 25mm long drive all screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5x25mm at 230mm C/C, including jointing and finishing to a flush finish of tapered and square edges of the gypsum board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufactures specification and also including the cost of making openings for light fittings, grills diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of Engineer-in-charge. 12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part-I : 2011 (Board with BIS certification marks)

Providing and applying white cement based putty of average thickness 2mm, of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete. (Birla/JK White)

White washing with lime to give an even shade. New work (three or more coats)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade new work (two or more coats) over and including priming coat with cement primer.

Applying one coat of water thin able cement primer of approved brand and manufacture on wall surface.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade. Two or more coat on new work.

Finishing wall with premium acrylic smooth exterior paint with silicon additives of required shade on new work (two or more coats applied @ 1.43 ltr./10sqm over and including base coat of water proofing cement paint applied @ 2.20kg/10sqm).

Finishing walls with textured exterior paint of required shade on New work (two or more coats Rustic Regular of any colour as per Engg. incharge) over and including base coat of exterior primer applied @ 3.00kg/10sqm.

Providing and fixing nickel plated S.S. pipe curtain rods with nickel plated brackets. 25mm dia (heavy type).

Providing 40x5mm flat iron hold fast 40cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing aluminium composite panel with specific aluminium channel as per approved make with 4mm thick aluminium composite sheet and joint filling with silicone complete as directed by Engineer-in-charge.

Providing and fixing of exterior wall cladding made of Grc of size 8” x 2 ¼” (Brick type) made by using high quality pigments, with ruff texture finish with acrylic urethane transparent coating to prevent it from aungus nad elgae. Shade / colour to be approved by the Engineer-in-charge. Tiles to be fixed by using grey cement and curing to be done twice a day for proper bonding. The tiles to be fixed on dry plaster surface with spacer of 5mm and then filled it with matching grout and then deep cut pointing horizontally and vertically. Make :- Classic – GRC, Granimitz (UNISTONE)

Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221-02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings/complexes/Residential with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multi-cellular to facilitate movement. (Material shall confirm to ASTM 6063.) Wall joint of 100 mm gap

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical location in load application areas that accommodates multi directional seismic movement without stress to its components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self centering arrangement that freely rotates / moves in all directions. The Self –centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer-in-Charge. (Material shall confirm to ASTM 6063.) Floor joint of 100 mm gap

Providing & Filling of RBM (River Bed Material) on road surface, including watering and compacting with power road roller under optimum moisture conditions to give at least dry density

Supplying and stacking at site Graded crushed stone aggregate of size 63 mm to 45 mm

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening /binding material to fill up interstices of coarse aggregate, watering and compacting to the required density

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge

Providing and applying tack coat using hot straight run bitumen of grade – VG-10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications. On W.B.M. @ 0.75 Kg/sqm

Providing and laying bituminous macadam using crushed stone aggregates of specified grading premixed with bituminous binder, transported to site by tippers, laid over a previously prepared surface with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specifications and directions of Engineer-in-Charge. 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 3.5% (percentage by weight of total mix) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity

Providing and applying tack coat using hot straight run bitumen of grade – VG-10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications.On bitumen surface @ 0.50 Kg/sqm

2.5 cm premix carpet surfacing with 2.25cum and 1.12 cum of stone chippings of 13.2 mm and 11.2mm size respectively per 100 sqm and 52 kg and 56 kg of hot bitumen per cum of stone chippings of 13.2 mm and 11.2 mm size respectively including a tack coat with hot straight run bitumen including consolidation with road roller of 6 to 9 tonne capacity etc. complete (tack coat to be paid for separately). With paving Asphalt grade VG-30 with no solvent

Providing and laying seal coat of premixed fine aggregate (passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG-10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface including rolling and finishing with road all complete

Carriage of material by Mechanical Transport including loading / unloading and stacking at site complete.

Sand for an average lead of 40Kms

Stone aggregate below 40mm size for an average lead of 10 Kms.

Stone aggregate 40mm size and above for an average lead of 10 Kms.

Bricks for an average lead of 70 Kms

Design manufacture, supply, installation, testing and commissioning of Lift (Gearless with Machine room) of following specifications:- Drive Machine :- Geared Traction Load Capacity :- 544 Kg Passenger Capacity :- 8 persons Control System :- Simplex automatic operation Maximum no. of stops :- 5 Max. rise :- 23 meters Car speed :- 1.5m/s Power Supply :- 3 phase, 440 volts, 50-60 Hz frequency Entrance :- Front only Door :- Automatic (Centre opening door) Car inside :- 1100mmX1300mm Hoistway size :- 1850mm X 1650mm Pit(mm) :- 1600 MAKE:- OTIS or Equivalent

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (Sintex, Electroplast, star, Lotous or equivalent having valid ISI license) (3000 ltr. Capacity 40 No.).

Paver Block

Providing, laying 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth etc. complete as per direction of Engineer-incharge for paver tiles

Providing and laying 80mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).Size 300x250x100mm

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etc upto floor V level, including curing but excluding the cost of centring, shuttering and finishing with 1:2:4 (1 cement :2 coarse sand :4 graded crushed stone aggregate 20 mm nominal size)

CIVIL WORK (B-Sanitary & Plumbing)

Providing & fixing of white vitreous China pedestal type water closet (European Type) with cistern (A/PHAS-100 +Cat No. 201100 + Cat No. 21054 or approved equivalent) with CP bolts, nuts, CI chair hanging arrangements, bakelite seat & cover with CP hinges & rubber buffers, CP brass screw, washer with all accessories with WC connector with Rubber Lip / Buffer and side gap filled with silicon sealant wherever required. Including brass / SS screws and washer complete including cutting, making good the walls, floors, slab wherever required as per direction of Engineer-in-charge.

Providing and fixing water closet squatting pan (Indian Type W.C Pan) Orsia pattern with 100mm sand cost iron P or S trap, 10 ltrs low lewel PVC flushing cistern including flush pipe (Hindware make Cat No. 20070/ Kerovit make Cat No. 606 or approved equivalent) Manually controlled device (Handle lever) conforming to IS : 7231, with all fitting and fixture complete including cutting and making good the wall and floows wherever required. Orissa Pan white viterous china pan of size 580x440mm with integral type footrests.

Providing & fixing of white vitreous China under counter oval wash basin / circular basin (Hindware 10080) with CP brass waste assembly, CP cast brass bottle trap with extension piece (Jaquar Cat No. 769B + Parko1535 or approved equivalent), 450mm long CP copper connections pipes (Jaquar Cat No. 803B or Parko 1535 or approved equivalent), wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-in-charge.

Providing and fixing of white vitreous china wash basin with pedestal (Hindware Cat No. 1008 + Pedestal Cat No. 11003) with CP brass waste assembly, CP cast brass bottle trap with extension piece (Jaquar Cat No. 769B+Parko 1535 or approved equivalent), 450mm long CP copper connections pipes (Jaquar Cat No. 803B or Parko 1535 or approved equivalent), wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-in-charge.

Providing and fixing CP single liver extended basin mixer (height 85mm) without Popup waste system with 450mm long Braided Hoses and brass nuts with all fittings and accessories as per direction of Engineer-in-charge (Jaquar FUS 290238 or approved equivalent).

Providing & fixing white vitreous china flat back urinal with automatic flushing systems (Hindware 60021 or approved equivalent) comprising of all plumbing, electronic and electrical items, CP brass flush pipe with CP brass elbow, CP brass spreader, CP wall flange, infrared photo cells, eyes, electrically operated solenoid valve, step down transformer, equipment and any other item required to provide satisfactory functioning including necessary wall cutting/ chasing and making good, as required for urinal flushing complete as mentioned above as per direction of Engineer-Incharge.

Providing and fixing stainless steel A ISI 304 (18/8)kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required.

Kitchen sink with drain board 510 x 1040mm bowl depth 225mm (Dry Canteen/Kitchen).

Kitchen sink without drain board 610 x 460mm bowl depth 200mm (Pantry).

Providing and fixing, testing and commissioning of C.P brass Sink mixer with regular swinging spout (wall mounted model) with connecting legs and wall flanges complete as required and making good as per direction of Engineer-in-charge (Jaquar Cat No. QQT 7309 or approved equivalent).

Providing and fixng C.P hand spray with lever control (health faucet) (Jaquar Cat No. ALDCHR-565 or approved equivalent) and flexible hose 1 Mtr long connection with C.P holder for hand spray complete in all respects as per direction of Engineer-in-charge.

Providing and fixing C.P brass angle valve for basin mixer and geyser points of approved quality conforming to IS : 8931 a) 15mm nominal bore (Make Jaquar FUS 29053 or approved equivalent).

Providing and fixing C.P brass robe hook (Jaquar Cat No. CAN 1191N) or approved equivalent) fixed to wall / door with plastic rawl plugs and C.P brass screws including cutting and making good the walls wherever required as per direction of Engineer-in-charge.

Providing and fixing recessed liquid soap dispenser with glass bottle (Jaquar Cat No. ACN 1135 N or approved equivalent) as per direction of Engineer-in-charge.

Providing and fixing of Soap Dish Holder with all fittings as per direction of Engineer-in-charge (Jaquar Cat No. ACN 113 N or approved equivalent).

Providing and fixing of Tumbler Holder with all fittings as per direction of Engineer-in-charge (Jaquar Cat ACN 114 N or approved equivalent).

Providing and fixing Bottle Trap (Jaquar Cat No. ALD. 769L or approved equivalent) and other ancillary fittings. Cutting and making good the walls wherever required compete as per directions of Engineer-Incharge.

Providing and fixing complete set of sanitary fixtures for handicapped toilets, Hindware Cat. No. 70002 or approved equivalent) comprising of EWC –P, Cistern, Seat Cover, Twin Flush Fittings Wash Basin 450X300, Half pedestal, 1 faucet with spatula lever, 1 hinged rail and 2 grab bars, including cutting and making good the walls and floors wherever required complete as per directions of Engineer in charge.

Providing and fixing 6mm copper backed float glass mirror MODI / SAINT-GOBAIN including 6mm thick BWR type ply board, 40mm stainless steel channel plugged to wall, hard wood treated with two coats of wood preservative etc. all complete as specified and shown in drawing complete to the satisfaction of Engineer-in-charge.

Providing and fixing C.P brass single towel rail (600mm long) of approved make complete with C.P brackets fixed to wooden cleats with C.P brass screws (Jaquar Cat No. ACN 11011NM or approved equivalent).

Providing and fixing brass towel Ring Round with Round Flenge of approved make complete with all fittings (Jaquar Cat No. ACN 11021 BN or approved equivalent).

Providing and fixing of glass shelf 600m long with all C.P fittings of approved quality complete item (Jaquar Cat No. ACN 11071 N or approved equivalent).

Providing and fixing toilet paper holder with all fittings Jaquar Contienal ACN 1153 N.

Providing and fixing 15mm dia C.P brass bib cock with wall flange of approved quality conforming to IS standard (Jaquar Cat No. 29037 or approved equivalent).

Providing and fixing 15mm dia C.P brass long nose bib cock of approved quality conforming to IS : standards and weighing not less than 810 grams (Jaquar Cat No. CON-107 KN or approved equivalent).

Providing and fixing of regular body of concealed stop cock suitable for 15mm pipe line with protection cap (Jaquar ALD-083 or approved equivalent) with exposed part angular stop cock with flange FUS 29.53.

Providing and fixing of wall mixer with provision for overhead shower with 115mm long bend pipe on upper side connecting legs and wall flanges of approved quality with all fittings (Jaquar FUS 29273UPR or approved equivalent).

Providing and fixing of wall mounted over head shower 200m dia (Jaquar DHS-CHR-1613) with shower arm 450mm long round shape with 90 degree bend with flanges (Jaquar SHA-479L450 or approved equivalent) with all fittings.

Providing, storing, handling, shifting, installation, testing & commissioning of vertical / horizontal storage type hot water heater fixed to wall with anchor bolts & nuts, 20mm CP brass cock and 20mm non return valve complete including making connection with 15 mm dia CP connecting pipe on Inlet and Outlet, suitable length of power cable and 15A plough (for pantry & Toilets).

Capacity 15 liters

Capacity 25 liters

Capacity 35 liters

Providing & fixing storage type water cooler with plain & cold water facility of the following capacity, I.S.I marked, stainless steel front panel, C.P brass push cock, inlet float valve with all plumbing and electrical accessories, inlet, outlet, overflow and PVC drain out connection to F.D complete as required (Blue Star / Voltas or equivalent).

Cooling capacity 20 Lts./hr (Model No. Bluestar PC240) Storage capacity 40 Lts.

Cooling capacity 40 Lts./hr (Model No. Bluestar PC480) Storage capacity 80 Lts.

PART B

INTERNAL DRAINAGE (SOIL, WASTE,VENT & RAIN WATER DISPOSAL PIPES FITTINGS):

Providing , fixing testing and commissioning of SWR TYPE -B soil, waste and vent pipes (IS:13592-1992) including all fittings confirming to IS 14735-99,rubber ring confirms to IS 5382 including all required fittings e.g. bends, junctions, cowls, offsets, access pieces,clamps etc. jointing with ring Joints as per recommendation of manufacturer specifications including cutting, chasing of brick/RCC structure and making good the same as required complete in all respects as per direction of Project -In- Charge.

160mm dia

110mm dia

75 mm dia

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing, laying, testing & commissioning of UPVC pressure pipes of 6 Kg/Sq.cm pressure rating class V (IS : 4985-2000) including fittings, tees, bends, clamps, coupling and adaptors supports, and jointing with solvent joint, testing and necessary earth work in excavation, backfilling, disposal of surplus earth with a lead upto 50m complete, compaction and consolidation including bed concrete (if required), sand bedding all around UPVC pipe & fittings and thrust blocks at bends as per standard design (for Drainage Sump Pump Discharge Header).

110 mm dia

160 mm dia

200 mm dia

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe

32 mm dia or 40 mm outer dia

40 mm dia or 50 mm outer dia

Providing, laying, testing & commissioning of UPVC pressure pipes of 10 Kg/Sq.cm pressure rating class V (IS : 4985-2000) including fittings, tees, bends, clamps, coupling and adaptors supports, and jointing with solvent joint, testing and necessary earth work in excavation, backfilling, disposal of surplus earth with a lead upto 50m complete, compaction and consolidation including bed concrete (if required), sand bedding all around UPVC pipe & fittings and thrust blocks at bends as per standard design (for Drainage Sump Pump Discharge Header). 63 mm outer dia

Providing & fixing UPVC deep seal P or S trap of self cleansing design with or without vent arm with provision for connecting pvc inlet fitting complete including cost of cutting and making good the walls and floors wherever required. 110mm inlet Outer Dia and110mm outlet outer Dia

Providing and fixing UPVC floor drain Floor Drain (B) With Jali (PP) 75 mm Reducing elbow (with UPVC grating and pipe to be paid separately), complete as per instructions.

Providing and fixing UPVC Clean Out plug (FCO & COP) with end cap for opening, complete in all respects. 110mm dia

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) including bed concrete as per standard design. 100 mm diameter S.W. pipe

PART C

DOMESTIC / FLUSHING/ COLD & HOT WATER SUPPLY :

PE-AL-PE COMPOSITE PRESSURE PIPE

INTERNAL WATER SUPPLY SYSTEM

Providing and fixing Polyethelene-Aiuminium-Polyethelene (PE-AL-PE) Composite Pressure Pipes conforming to 15:15450 U.V. stabilised with carbon black having thermal stability for hot and cold water supply, capable to withstand temperature upto 80°Cincluding all special brass fittings of composite material (engineering plastic blend and brassinserts wherever required) e"g. Elbows, tees, reducers,couplers and connectors etc. with clamps at one meter spacing. This includes testing of joints complete as per direction of the Engineer-in-charge:make :Rehau / Kitech/ viega .Internal work-exposed on wall with clamps at 1.00 meter spacing

1216 (16mm OD) pipe

1620 (20mm OD) pipe

2025 (25mm OD) pipe

2532 (32mm OD) pipe

3240 (40mm OD) pipe

4050 (50mm OD) pipe

Internal work concealed with clamps at 1.00 meter spacing including cutting the chases and making good the wall etc.

1216 (16mm 00) pipe

1620 (20 mm OD) pipe

2025 (25 mm OD) pipe

2532 (32 mm OD) pipe

Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. (external work) (Medium Class)

65 mm dia. nominal bore

80 mm dia. nominal bore

100 mm dia. nominal bore

150 mm dia. nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete copatable to connection with composite pipe

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

32 mm dia. Nominal bore

40 mm dia. Nominal bore

50 mm dia. Nominal bore

Providing and fixing G.l. pipes complete with G.l. fittings and clamps, including cutting and making good the walls etc. INTERNAL WORK-Exposed on wall

15 mm dia. nominal bore (Medium)

20 mm dia. nominal bore (Medium)

25 mm dia. nominal bore (Medium)

32 mm dia. nominal bore (Medium)

40 mm dia. nominal bore(Medium)

50 mm dia. nominal bore(Medium)

Providing and fixing nitrile rubber insulation on hot water supply / return pipes.

15 mm dia (9 mm thickness)

20 mm dia (9 mm thickness)

25 mm dia (9 mm thickness)

32 mm dia (13 mm thickness)

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified

65mm dia.

80mm dia.

100mm dia.

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete

25 to 40 mm nominal bore

50 to 80 mm nominal bore

Providing & fixing Auto Air vent for cold water supply risers, suitable for pressure not less than 15 Kg/Sq.cm.

15 mm dia

20 mm dia

Providing and fixing in position of approved quality high pressure rated Brass Float Valve with copper ball float and brass rods of required length suitable for test pressure of not less than 15 Kg/sqcm of the following sizes:

40 mm dia

50 mm dia

Providing and laying Double Flanged (Screwed/ Welded) Centrifugally (Spun) Ductile Iron Pipes of Class K-9 conforming to IS : 8329 100 mm dia Ductile Iron Double Flanged

Excavation of trenches of required width for pipes etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5m, including getting out the excavated soil, and then returning soil as required, in layers not exceeding 20cm depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed outside the site to the approved dumping ground. Minimum width of the trench should be external dia plus 400mm. Trenches to be excavated with required slope and shall be aligned as per drawing .

Pipes, cables etc, not exceeding 80 mm dia.

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Part D

EXTERNAL SEWER AND DRAINAGE SYSTEM

Excavation of trenches of required width for pipes etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5m, including getting out the excavated soil, and then returning soil as required, in layers not exceeding 20cm depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed outside the site to the approved dumping ground. Minimum width of the trench should be external dia plus 400mm. Trenches to be excavated with required slope and shall be aligned as per drawing .

Pipes, cables etc, not exceeding 80 mm dia.

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Providing, fixing, jointing, testing and commissioning of UPVC “NU-DRAIN” for Drainage and sewerage/strom water application Pipe conforming to IS:15328 with all fittings such as bends, tees, elbow. The wall thickness of pipe and technical characteristic conforms to IS:15328 in SN8 stiffness class. The fitting dimension conforming to BS: EN1401-1998. The jointing to be completed with rubber ring/solvent weld joint as suitable at site for above basement level.(Aprroved Make- Supreme/prince/jain)

200 mm diameter

Providing, fixing, jointing, testing and commissioning of UPVC “ECODRAIN” structured wall Drainage Pipe conforming to IS:16098 (Part-I) with all fittings such as bends, tees, elbow. The wall thickness of pipe and technical characteristic conforms to IS:16098 (Part-I) in SN8. The fitting dimension conforming to BS: EN1401-1998. The jointing to be completed with rubber ring/solvent weld joint as suitable at site for use at non basement area. Make- Supreme/prince/jain

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand:10 graded stone aggregate 40 mm nominal size) including bed concrete as per standard design.

All around S.W. pipe

100 mm diameter S.W. pipe

150 mm diameter S.W. pipe

200 mm diameter S.W. pipe

Upto haunches of S.W. pipe

100 mm diameter S.W. pipe

150 mm diameter S.W. pipe

200 mm diameter S.W. pipe

Providing and fixing square- mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design.

180 x 150 mm size P type

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement: 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III): 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

With Sewer bricks conforming to IS : 4885

Extra for depth for manholes

Size 90x80 cm

With Sewer bricks conforming to IS : 4885

Providing orange colour safety foot rest of minimum 6mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25 mm and over all minimum length 263mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing. including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Supplying and fixing C.I. cover without frame for manholes:

560 mm diameter C.I. cover ( heavy duty) the weight of the cover to be not less than 108 kg

Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5kg.

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete

For pipes 100 to 250 mm diameter

Extra for depths beyond 60 cm of sand cast iron drop connection complete :

For 150 mm dia. sand cast iron drop connection

Providing and fixing of three phase monobloc pumpset with CAT-A + Mech. Seal, 3 hp, 2.2 KW with flow upto 525 LPM at the head of maximum 17 mtrs. Cast iron casing and body, impeller: Cast iron/bronze.(make WILO, GRUNDFOS,XYLEM)

SUB WORK :- FIRE FIGHTING WORKS

INVANTRY

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all

respects, as required: (Terrace Pump)

Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520

Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.

M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.

Suitable cement concrete foundation duly plastered and with anti vibration pads.

900 lpm at 35 m Head

450 lpm at 35 m Head

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming toIS1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.

150 mm. Dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

25 mm dia

80 mm dia

100 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Gunmetal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

100 mm dia

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required

100mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

150mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Gun Metal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required.

20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585

20 mm nominal internal dia gun metal globe valve & nozzle.

Drum and brackets for fixing the equipmets on wall.

Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

Gun metal

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

2 way-100 mm dia M.S. Pipe

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required (E&M)

Providing & fixing of FIRE shaft door with frame section (100X50)mm made up of 1.6mm (16SWG) MS sheet with Powder coated including necessary locking arrangement & 5mm glass with Chest handle as required,including painting (RED Powder Coated ) with "FIRE SHAFT " legend. Size (1200 x 2100) mm

PORTABLE FIRE EXTINGUISHERS

Providing & fixing of ISI marked (IS:15683) portable fire extinguisher, carbondioxide type flat base including valve, discharge hose of not less than 10 mm dia. 1 M long & complete in all respects including initial fill with CO2 gas confirming to IS:307-1966 filled to a filling ratio of not more than 0.667 of not more than 0.667 and wall suspension bracket

Capacity 4.5 kg

6 Kg. ABC Powder type fire extinguishers are manufactured and marked to Indian standard IS: 15683. Suitable first aid appliance for fighting fires in Class A, B & C fire that is wood, textile, flammable liquids & gases.

EXTERNAL PLUMBING PUMPS AND FIRE FIGHTING WORK

U.G TANKS & PLANT ROOM AND EXTERNAL WATER SUPPLY SYSTEM

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc.and disposing of surplus excavated soil as directed,within a lead of 50 m :

All kinds of soil

Pipes, cables etc, not exceeding 80 mm dia.

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Providing and laying S&S Centrifugally Cast (Spun)/ Ductile Iron Pipes conforming to IS : 8329

100 mm dia Ductile Iron Class K - 9 Pipes

150 mm dia Ductile Iron Class K - 9 Pipes

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work :

100 mm diameter pipe

150 mm diameter pipe

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) :

100 mm dia nominal bore

150 mm dia nominal bore

NON - RETURN VALVE with dual plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating as specified.

150mm dia.

100mm dia.

80mm dia.

Providing and fixing C.I. sluice valves (with cap) complete with bolts,nuts, rubber insertions etc. (the tail pieces if required will be paid separately).

150 mm diameter

Class II

100 mm diameter

Class II

Providing and fixing G.I. pipes (Heavy duety)complete with G.I. fittings and clamps,including cutting and making good the walls etc.:(U.G Tank and plant room )

Internal work-Exposed on wall

U.G Tanks & plant room work

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

50 mm dia nominal bore

65 mm dia nominal bore

80 mm dia nominal bore

100 mm dia nominal bore

150 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work):

25 mm nominal bore

32 mm nominal bore

Painting G.I. Pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality.

25 mm diameter pipe

32 mm diameter pipe

40 mm diameter pipe

50 mm diameter pipe

65 mm diameter pipe

80 mm diameter pipe

100 mm dia nominal bore

150 mm dia nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete

25 mm nominal bore

Supplying, fixing, testing and commissioning of following valves,gauges and strainers for condenser water circulation as per specifications.

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified.

150 mm dia. Nominal bore

100 mm dia. Nominal bore

80 mm dia. Nominal bore

65 mm dia. Nominal bore

Providing & fixing Auto Air vent for cold water supply risers, suitable for pressure not less than 15 Kg/Sq.cm. 50MM DIA

Providing and laying UPVC pipes (I.S:4985) of 10kg./cm2 including all fittings with or without access door i.e bends, junctions, cowls, offsets, etc., and jointing with solvent cement including cutting holes in walls and floors ,wherever required and making good the same, complete as directed by the Engineer-in-Charge.( for external garden hydrant only )

Supply fo uPVC pipes of 10 kg / cm2 conforming to IS: 4985 including all PVC fittings

Constructing masonry chamber 300x300x600mm inside (Garden Hydrant Chambers) with 75 class designation brick work in cement mortar 1:4 (1cement : 4 coarse sand) for garden hydrant valves of dia 32 mm and below with Pre-cast RCC/CI cover, complete including all necessary excavation, back filling and disposal of surplus earth as per instructions, foundation concrete 1:5:10 (1 cement: 5 coarse sand : 8 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement: 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design and as per attached sketch.

Constructing masonry chamber 600x600x750mm inside with 75 class designation brick work in cement mortar 1:4 (1cement : 4 coarse sand) for butterfly valves/sluices valve of dia 80mm and above with C.I. surface box 100mm top diameter 160mm dia bottom diameter and 180mm deep (inside) with chained lid and 150mm thick RCC top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) necessary excavation, back filling and disposal of surplus earth as per instructions, foundation concrete 1:4:8 (1 cement: 4 coarse sand : 8 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3(1 cement: 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design.

WATER SUPPLY, DRAINAGE, PUMPS & EQUIPMENT

Providing and fixing centralized water level controller cum indicator system, as per the following details:

Centralised PLC control panel along with touch-screen display board (min. 8" Diag. size) along with all accessories for complete controls & indication. Panel shall be made out of CRCA sheet min. 2mm thick having necessary interlocks, I/O's, required number of repeater amplifiers, all audio-visual alarms as required specifications as listed below. An emergency stop push button shall be provided in the panel. The panel shall have Modbus compatibility for seamless BMS/BAS Integration and shall be of approved make. The complete system control matrix, wiring diagram, SLD's and technical details shall be submitted by the vendor and gotten approved before commencement of execution of works.

Water level indicators cum controllers working on hydrostatic pressure measurement principle made of Stainless Steel for installation on storage tanks, and capable of providnig 4 to 20 mA analog signal compatible with PLC signal inputs and complete as per working requirements for details of equipment below. All control outputs to MCC panel shall be included as per requierments.

Fire Static Underground tanks

Real-Time water level indication monitoring

V. Low Level audio-visual alarm at less than 25% total capacity.

Raw Water Underground tanks

Real-Time water level indication monitoring

V. Low Level audio-visual alarm at less than 30% total capacity.

V. High Level audio-visual alarm at more than 100% total capacity.

Auto cut-in of tubewell pumps at 35%

Auto cut-out of tubewell pumps at 95%

Auto cut-out of raw water pumps at 35%

Domestic Water Underground tanks

Real-Time water level indication monitoring

V. Low Level audio-visual alarm at less than 30% total capacity.

V. High Level audio-visual alarm at more than 100% total capacity.

Auto cut-in of raw water pumps at 35%

Auto cut-out of domestic water pumps at 35%

Flushing Water Underground tanks At STP

Real-Time water level indication monitoring

V. Low Level audio-visual alarm at less than 30% total capacity.

V. High Level audio-visual alarm at more than 100% total capacity.

Auto cut-in of raw water pumps (from STP) at 35%

Auto cut-out of flushing water pumps at 35%

Domestic Water Overhead tanks

Real-Time water level indication monitoring

V. Low Level audio-visual alarm at less than 30% total capacity.

V. High Level audio-visual alarm at more than 100% total capacity.

Flushing Water Overhead tanks

Real-Time water level indication monitoring

V. Low Level audio-visual alarm at less than 30% total capacity.

V. High Level audio-visual alarm at more than 100% total capacity.

Providing complete testing kit with all chemicals complete suitable for conducting test on water quality. The test kit shall be suitable to measure TDS, pH, Hardness, Iron content and other parameters

Hydro-pneumatic pumping system for Domestic water supply to OHT

Providing, fixing and testing of packaged type skid mounted hydropneumatic system with variable frequency drive type comprising of :

(i) Vertical, inline multistage centrifugal pumping set with stainless steel SS-304 stage casing and SS-304 impellers with stainless steel SS-304 shaft as per IEC standards and GJL250 cast iron suction & discharge casing, connected to TEFC ventilated induction motor of 2 pole, 2900rpm, suitable for 400/440 Volts, 3 phase, 50 Hz A.C. supply.

(ii) Pressure vessel of non corrosive FRP composite construction lined with NSF and/or FDA listed material, like high density polyethylene with fully replaceable polyurethane. Air cell burst pressure of minimum of 5 times the vessel operating pressure and cycle tested for 2,50,000 cycles.

(iii) Control Panel with programmable logic controller (PLC) for cyclic operation of pumps + Variable Frequency Drive. The Pump working sequence should change after every operation.Contractor overload relays and MCBs should confirm to IEC 898 – 1995/ specifications. Blinking indications for pumps start, trip, low level trip, health supply should be provided in the panel along with the ammeter & voltmeter. Control panel should also consist of cooling fan.

(iv) Pressure switches bellow type fitted with micro switch and having maximum pressure and differential scale should confirming BS-6134 standards and IP55 protection class.

(v) All required Ball Valves, Non-return valves, flexible connectors etc. and all required accessories, Heavy Duty S.S 316 Manifold to make the system completely operational as a skid mounted system. Ball valves to be used should be Hot Pressed brass OT-58 with stainless steel ball and P.T.F.E seal and O-Ring. NRVs to be used should be with Springs and O-Ring arrangement.

(Vendor to submit performance curves and technical catalog of the proposed model for review & information)

Complete manifold system shall be factory aasembled & totally mounted on a common base frame with following duties:

Note: Contractor to note that the suction header is required to have inlet connection from the Puddle Flange @ water tanks and to the pump suction. Provision of delivery header is required to have outlet connection from the pumps. Suitable outlet flanges from the delivery mainfold / header shall be provided as required.

For Domestic water supply for Auditorium, Adm.Acadmic & Animal Building (PHASE-1 )

No. of Pumps :1 (1 Working +1 Standby)

Capacity : 350 LPM each pump

Head : 75 Meters

apx. HP (Motors) : 5 HP

Location : Plumbing Plant Room

For Domestic water supply for RESIDENTAL BUILDING (PHASE-2)

No. of Pumps :1 (1 Working +1 Standby)

Capacity : 400 LPM each pump

Head : 80 Meters

apx. HP (Motors) : 5 HP

Location : Plumbing Plant Room

For flushing water Relift pump for Auditorium, Adm.Acadmic & Animal Building (PHASE-1 )

No. of Pumps :1 (1 Working +1 Standby)

Capacity : 250 LPM each pump

Head : 75 Meters

apx. HP (Motors) : 3 HP

Location : STP Plant Room

For flushing water Relift pump RESIDENTAL BUILDING (PHASE-2)

No. of Pumps :1 (1 Working +1 Standby)

Capacity : 250 LPM each pump

Head : 80 Meters

apx. HP (Motors) : 3 HP

Location : STP Plant Room

Garden hydrents & floor washing Relift pump

Providing and fixing vertical, inline multistage centrifugal pumping set (Complete manufactured Skid-Mounted arrangement with manifold and accessories) with stainless steel SS-304 stage casing and SS-304 impellers with stainless steel shaft as per IEC standards and GJL250 cast iron suction & discharge casing, connected to TEFC ventilated induction motor of 2 pole, 2900 RPM, suitable for 400/440 Volts, 3 phase, 50 Hz A.C. supply with pressure gauge and with gunmetal isolation cocks, vibration elimination pads etc. complete with base and frame, nuts and bolts and necessary RCC foundations as per requirement as per instructions and pump shall have following duty:

No. of Pumps :2 (1 Working +1 Standby)

Capacity : 350 LPM each pump

Head : 55 Meters

apx. HP (Motors) : 4 HP

Location : STP Plant Room

Vendor to submit proposed pump model with duty curve.

For WTP & STP Plant room drainage

Flow rate : 450 LPM

Head : 15 Mts

Solid Handling : 100 MM

Location : Sump of Basement

Purpose : Plant Room & general area Drainage

MOC : SS body SS Impeller & Shaft

Manhole Cover for U.G Tanks and Sumps

Supplying and fixing C.I. cover without frame for manholes :

Providing and fixing extra heavy duty, double seal, water tight C.I manhole cover and frame specially casted for placing over the underground water tanks with lifting and locking arrangements as per approved sample, complete in all respect including fixing in PCC as per site requirement.

Providing and fixing stainless steel ladder, wall mounted of 4m height(app) for underground tanks complete with flanged ends and inserts (removable type) made of 38mm/42mm dia 16 G S/S 304 quality pipe made as per international quality standards of approved shape and size with non skidding steps at 300mm vertical spacing, complete as directed by the engineer in charge.

EXTERNAL SEWER AND DRAINAGE SYSTEM

Excavation of trenches of required width for pipes etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5m, including getting out the excavated soil, and then returning soil as required, in layers not exceeding 20cm depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed outside the site to the approved dumping ground. Minimum width of the trench should be external dia plus 400mm. Trenches to be excavated with required slope and shall be aligned as per drawing .

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm

Providing, fixing, jointing, testing and commissioning of UPVC “NU-DRAIN” for Drainage and sewerage/strom water application Pipe conforming to IS:15328 with all fittings such as bends, tees, elbow. The wall thickness of pipe and technical characteristic conforms to IS:15328 in SN8 stiffness class. The fitting dimension conforming to BS: EN1401-1998. The jointing to be completed with rubber ring/solvent weld joint as suitable at site for above basement level.(Aprroved Make- Supreme/astral/jain)

200 mm diameter

250 mm diameter

300 mm diameter

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement: 2 fine sand) including testing of joints etc. complete

150 mm dia. R.C.C. pipe

250 mm dia. R.C.C. pipe

300 mm dia. R.C.C. pipe

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand:10 graded stone aggregate 40 mm nominal size) including bed concreteas per standard design.

All around S.W. pipe

150 mm diameter S.W. pipe

200 mm diameter S.W. pipe

230 mm diameter S.W. pipe

250 mm diameter S.W. pipe

Providing and fixing square- mouth S.W./ UPVC gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design.

100x100 mm size P type

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

With Sewer bricks conforming to IS : 4885

Providing and laying non-pressure of specified class R.C.C. Pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement: 2 fine sand) including testing of joints etc. complete.

Non-pressure NP-3 class (Medium duty) R.C.C. pipes

450 mm dia. R.C.C. pipe

600 mm dia. R.C.C. pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement: 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III): 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80 cm and 60 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

With Sewer bricks conforming to IS : 4885

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

With Sewer bricks conforming to IS : 4885

Extra for depth for manholes

Size 90x80 cm

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

With Sewer bricks conforming to IS : 4885

Size 120x90 cm

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

With Sewer bricks conforming to IS : 4885

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

With Sewer bricks conforming to IS : 4885

Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

1.68 m deep with SFRC Cover and frame (heavy duty HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

With Sewer bricks conforming to IS : 4885

Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design

2.30 m deep with SFRC Cover and frame (heavy duty HD- 20grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :

Extra depth for circular type manholes

Manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

With Sewer bricks conforming to IS : 4885

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

With Sewer bricks conforming to IS : 4885

Manhole 1.52 m internal dia (at bottom) beyond 2.30 m

Providing M.S. foot rests including fixing in manholes with 20x20x10cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design :

With 20x20 mm square bar

With 20 mm diameter round bar

Providing orange colour safety foot rest of minimum 6mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25 mm and over all minimum length 263mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing. including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Replacement of M.S. foot rests in manholes including dismantling concrete blocks and fixing with 20x20x10 cm cement concrete blocks 1:3:6 ( 1 cement : 3 sand : 6 graded stone aggregate 20 mm nominal size)

With 20x20 mm square bar

With 20 mm diameter round bar

Supplying and fixing C.I. cover without frame for manholes:

455x610mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg.

500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg.

560 mm diameter C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg

Providing and fixing in position precast R.C.C. manhole cover and frame of required shape and approved quality.

Rectangular shape 600x450 internal dimensions

Square shape 450mm internal dimensions

Circular shape 450mm internal diameter

Square shape 450mm internal dimensions

Circular shape 500mm internal diameter

Circular shape 560mm internal diameter

Circular shape 560mm internal dia.

Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5kg.

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete

For pipes 350 to 450 mm diameter

Providing sand cast iron drop connection externally for 60 cm drop from branch sewer line to main sewer manhole including inspection and cleaning eye with chain and lid, sand cast iron drop pipe and bend encased alround with cement concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) with all centering and shuttering required, cutting holes in walls and making good with brick work in cement mortar 1:4 ( 1 cement : 4coarse sand) plastered with cement mortar 1:3 (1 cement :3 coarse sand)on inside of the manhole wall lead caulked joints between sand cast iron pipes and fittings, stiff cement mortar 1:1 ( 1 cement : 1 fine sand) joints between sand cast iron tee and S.W. pipe, making required channels complete as per standard design and specifications :

100 mm dia. sand cast iron drop connection

150 mm dia. sand cast iron drop connection

Extra for depths beyond 60 cm of sand cast iron drop connection complete :

For 100 mm dia. sand cast iron drop connection

For 150 mm dia. sand cast iron drop connection

Constructing brick masonry road gully chamber of specified size with common burnt clay(non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4coarse sand) including precast R.C.C. horizontal grating with frame complete as per standard design:

Chamber size 50x45x60 cm including precast R.C.C grating with frame 500x450 mm horizontal grating.

Chamber size 45x45x77.50 cm including precast R.C.C grating with frame 450x100 mm vertical grating.

Chamber size 110x50x77.50cm including precast R.C.C grating with frame 500x450 mm horizontal and 450x100 mm vertical grating.

Constructing brick masonry chamber for underground C.I. inspection chamber and bend with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg ) R.C.C. top slab with 1:1 ½ : 3 mix ( 1 cement : 1 ½ coarse sand : 3 graded stone aggregate 20 mm nominal size),foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :

Inside dimensions 455x610 mm and 45 cm deep for single pipe line-

Inside dimensions 500x700 mm and 45 cm deep for single pipe line with one or two inlets

Inside dimensions 600x850 mm and 45 cm deep for single pipe line with three or more inlets.

Extra for depth beyond 45 cm of brick masonry chamber with common burnt clay (non modular) bricks of class designation 7.5

For 455x610 mm size

For 500x700 mm size

For 600x850 mm size

OIL AND GREASE SEPARATOR CHAMBER:

Providing and installation For underground installation, installation depth 550 - 950 mm, with integrated sludge trap, polymer upper section, vertically adjustable, rotatable and tiltable up to 5°, cast iron cover in load class B based on EN 124, odor tight.Ø 110 in-and outlet according to DIN 1953419560 (PP or AS piping). Version: Right (can be changed to left side version by exchanging inlet and outlet). Certification number: Z-54.1-474 Size: NS 4 Sludge trap capacity: 400 liter Total separator capacity: 400 liter Grease storage capacity: 160 liter Inlet / Outlet: DN 100 (DA 110 mm) Sludge trap capacity: 400 l Total separator capacity: 370 l Fat storage: 160 l Certification: Z-54.1-440 Weight: 130 kg Dimension: 1470 x 1300 mm Inspection chambers may be installed in a maximum of 500 mm groundwater Recomended Manufacturer: KESSEL

Construction of rain water harvesting well of 2.5 meter dia and 3.0 meter effective depth with the operation of earth work in excavation and drilling with RC/DC/Calyx rig having 400/450mm dia bore size up to aproximate 45m deep in all kind of starta including hard rock, back filling with available exavated earth, with necessary compaction and shifting of surplus earth outside by mechanical means as directed by the Project Incharge, PCC 1:5:10 , 200mm thick foundation concrete, brick work in cement mortar 1:4 (1 cement : 4 coarse sand), PVC coated safety steel foot rest of 12mm dia MS bars grouted rigidly in cement concrete 1:2:4 @300mm c/c, 200mm thick RCC tank cover slab in cement concrete M20 i/c providing and placing necessary steel raft, bars and to keep the provision of removable slab of approx. 1mx1m size, filling 300mm, 300mm & 300mm thick of 40-65mm nominal size graded stone aggregate, small stone and sand layer respectively, CI vent pipe, (100mm dia), 250mm dia...contd...

..contd...uPVC slotted pipes 6Kg./sq cm working pressure, filling around the slotted pipes and packing 3mm to 6mm sized graded and screened rounded pea gravel duly washed fabricating and placing grating at the mouth of pipes, placing 560mm dia SFRC manhole cover with frame etc. i/e all necessary materials and equipments required for all relevant operations as shown in the drawing.

Construction of brick masonry desilting chamber of size 200x100x60cm (effective depth) before rainy well with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) , foundation concrete 1:4:8 mix (1 cement : 4 coarse sand; 8 graded stone aggregate 40mm nominal size), inside and outside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement inside and rough plaster on outside, including fixing of grating , neatly finished complete in all respects including neccessary excavation, refilling and disposal of surplus earth, complete as per attached Sketch.

FIRE PUMPS AND ACCESSORIES

DSR_AOR_FOR_WET_RISER_AND_SPRINKLER_SYSTEM_2019

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required :

Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.

Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325.

M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.

Suitable cement concrete foundation duly plastered with anti vibration pads.

2850 lpm at 70 m Head

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects,as required : (Diesel Driven Pump)

Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.

Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required.

M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required.

Suitable cement concrete foundation duly plastered and with anti vibration pads.

2850 lpm at 70 m Head

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump)

Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520.

Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325.

M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.

Suitable cement concrete foundation duly plastered and with anti vibration pads.

180 lpm at 70 m Head

CONTROL PANELS

Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, inter-connection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :

Incomings

LED type RYB phase indicating lamps, ON, OFF, trip indicating lamps Set of Copper Bus Bar 800Amps

Outgoings

Main Fire Pump

Jockey Pump

Diesel Engine Control

Control for diesel engine comprising -Automatic/Manual selctor switch & 3 attempts starting device, timers and relays as required, push buttons, start/stop in manual mode

Indicating lamp for high/ Low Lub. Oil pressure, High Water Temp and Engine on indication

System Controller

Designing, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specification

Designing, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specification

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming toIS1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.

200 mm. dia (wall thickness = 6.3 mm)

150 mm. Dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

80 mm dia

100 mm dia

150 mm dia

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :

80mm dia

100mm dia

150mm dia

200mm dia

250mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required

80mm dia

100mm dia

150mm dia

200mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

80mm dia

100mm dia

150mm dia

200mm dia

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

2 way-100 mm dia M.S. Pipe

4 way - 150 mm dia M.S. Pipe

3 way - 150 mm dia M.S. Pipe

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal / Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Gunmetal

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Gun Metal

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

Gun metal

PORTABLE FIRE EXTINGUISHERS

Providing & fixing of ISI marked (IS:15683) portable fire extinguisher, carbondioxide type flat base including valve, discharge hose of not less than 10 mm dia. 1 M long & complete in all respects including initial fill with CO2 gas confirming to IS:307-1966 filled to a filling ratio of not more than 0.667 of not more than 0.667 and wall suspension bracket

Capacity 4.5 kg

6 Kg. ABC Powder type fire extinguishers are manufactured and marked to Indian standard IS: 15683. Suitable first aid appliance for fighting fires in Class A, B & C fire that is wood, textile, flammable liquids & gases.

Providing and fixing mechanical foam type fire extingushers consisting of welded M.S. trolley mounted cylindrical body, squeeze lever discharge valve fitted with pressure discharge hose, discharge nozzle, trolley etc., ISI marked as per IS:IS:13386 finished externally with red enamel paint.

Capacity 50 lit (D.G.Room)

Providing and fixing carbon-di-oxide fire extingushers trolley mounted with all accessories internal discharge tube,high pressure discharge hose,discharge nozzle, ISI marked as per IS:2878 finished externally with red enamel paint.

Capacity 22.5 kg.

SUB WORK :- ELECTRICAL WORKS (PHASE - 2)

Sub-Head : WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable Gl box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Make:- CCI/havells/polycab/Anchor/Finolex

Group C

Supplying & Fixing Of Following Sizes Of PVC Conduit Along

With Accessories in Surface / Recess Including Cutting the

Wall And Making Good the same In Case of recess Conduit as

Required Make:- BEC/Precision/AKG/POLYPACK/Anchor

Supplying & Fixing Of Following Sizes Of Steel Conduit Along

With Accessories in Surface / Recess Including Cutting the

Wall And Making Good the same In Case of recess Conduit as

Required Make:- BEC/AKG/STEEL CRAFT/ RMCON

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm ERLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm ERLS PVC insulated copper conductor single core cable etc. as required. Make:- CCI/havells/polycab/Anchor/Finolex

Group C

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. Make:- CCI/havells/polycab/Anchor/Finolex

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. Make:- CCI/havells/polycab/Anchor/Finolex

2 X 1.5 sq. mm +1X 1.5 sq. mm earth wire

2 X 2.5 sq. mm +1X 2.5 sq. mm earth wire

2X6 sq. mm +1X 6 sq. mm earth wire

4 X 6 sq. mm +2X 6 sq. mm earth wire

4 X 10 sq. mm +2X 6 sq. mm earth wire

4 X 16 sq. mm +2X 6 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Make:- NORTHWEST(PLATIA), SCHNEIDER(ZEN CELO), MK (BLENZE), LEGRAND(ARTEOR).

5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Telephone socket outlet

TV antenna socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. Make:- NORTHWEST(PLATIA), SCHNEIDER(ZEN CELO), MK (BLENZE), LEGRAND(ARTEOR).

Supplying and fixing following size/ modules, Gl box alongwith modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying & fixing suitable size Gl box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Sub-Head : MCCB, MCB & OB'S

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB) Make:- Schnider ACTI-9/SIEMENS Betagaurd(8GB32)/Hager Novello

4 way (4 +12), Double door

6 way (4 +18), Double door

8 way (4 +24), Double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/lsolator)

6 way, Double door (For EM. DB)

8 way , Double door (For EM. DB)

12 way, Double door (For EM. DB)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. MAKE:- SCHNIDER(ACTI - 9)/SIEMENS(BETA GUARD)/L&T (AU).

Single pole

Double pole

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. MAKE:- SCHNIDER(ACTI - 9)/SIEMENS(BETA GUARD)/L&T (AU).

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/recessed steel/PVC conduit as required. MAKE:- BELDEN/PANDUIT/POLYCAB/LEGRAND

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. Make:- BEC/PRECISION/AKG/Polypack/Anchor

Sub-Head : EARTHING

Earthing with G.l. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/coke and salt as required. (For transformer/MLP/MDB/HT Panel/HT Meter)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm G.l strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.l. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.l. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.l. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.l. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/cable as required.

Sub-Head : LIGHTNING CONDUCTOR Make:- OBO/Nimbus/Taran(SGI)/Ashlok

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.l. tube, having single prong at top, with 85 mm dia 6 mm thick G.l. base plate including holes etc. complete as required.

Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required.

Jointing copper / G.l. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/sweating and soldering etc as required.

Providing and fixing G.l. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.l. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.l. strip, 125 mm long, with 4 nos. of G.l. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Earthing with G.l. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt as required.

Providing and laying G.l. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Total of the Sub-Head - Lightning Conductor :

Sub-Head : MV CABLE LAYING

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. MAKE:- CCI, Havells, Polycab

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.l. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Sub-Head : MV CABLE JOINTING & END TERMINATION

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. MAKE:- COMET/PEECO/Siemons/Dowells

3½ X 300 sq. mm

3½ X 240 sq. mm

3½ X 50 sq. mm

3½ X 35 sq. mm

4 X 25 sq. mm

4 X 16 sq. mm

4 X 10 sq. mm

Sub-Head : MISC. CIVIL ITEMS

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

63 mm dia (OD-63 mm & ID-51 mm nominal)

160 mm dia (OD-160 mm & ID-135 mm nominal)

Sub-Head : FIRE DETECTION AND ALARM SYSTEM

FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL) Make:- Honeywell/Bosch/Siemens/Notifier

Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required.

CABLING & WIRING

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. Make:- CCI/Havells/Polycab/Anchor/Finolex

2 x 1.5 sq. mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. Make:- BEC/Precision/AKG/POLYPACK/Anchor

INTELLIGENT FIRE ALARM SYSTEM Make:- Honeywell/Bosch/Siemens/Notifier

Two Loop Panel.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of addressable beam detector with short circuit isolator (inbuilt or seperate) complete with emitter and receiver including connections with remote test features etc complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of intelligent interface unit BACnet/ Modbus protocol i.e. supplying communication links between building management system and fire alarm control panel complete as required.

PUBLIC ADDRESS SYSTEM

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required.

speaker cable Single pair, 2-core, 1.5 sqmm

speaker cable Four pair, 2-core, 1.5 sqmm

MV SWITCHGEAR PANELS & DISTRIBUTION BOARDS :

Design, manufacture, supply, installation, testing and commissioning of following Utility panels suitable for 415 V, 3 phase, 4 wire, 50 Hz power distribution system. The panel shall be Indoor, free standing, floor mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type compartmentalised design fabricated out of 2mm thick CRCA sheet steel for Load bearing members and 1.6 mm thick for non-load bearing members, complete with colour coded, heat shrinkable PVC insulated, aluminium bus bars and separate earth bus bar of adequate cross section through out the length of the panel. The incoming and outgoing feeders shall be accommodated in a fully segregated, modular multitier arrangement with adequate size and distinct cable alley, bus bar alley/chamber (form-3b Construction). The panel shall be complete with name plate, earthing, numbering, danger plate etc. as required and as per specifications and drawings. The panel shall withstand the fault level of as indicated elsewhere or shown in Single Line Diagram.

Important Notes: Common for all Switchboard:

The BOQ shall be read inconjunction with general notes, specification and Single Line Diagram (attached for Ref.). Incase of any discrepancy between specification, BOQ and SLD, the same shall be brought to the notice of Client/Consultant before quoting the rates, otherwise stringent condition shall be deemed to have been considered.

All MCCB shall be provided with door interlocked rotary handle with ON/TRIP/OFF position indicator, continious variable thermal magnetic O/C and S/C releases. All rating MCCB's shall be thermalmagnetic type.

Incoming MCCBs shall be provided with O/C, S/C, and Earth fault protection releases.

Outgoing MCCBs shall be provided with O/C, short circuit protection.

All feeder doors shall have pad locking arrangement.

All TP feeders shall have solid isolable neutral link.

All MCCB used in starter feeder shall be suitable for motor duty application.

All power contactors including NIC shall be of AC3 duty.

All ACB's shall be with micro processor based releases and Breaker Control Switch (BCS) having lost motion device.

Spare contaCTs of ACB/Relays/Contactor etc. shall be wired upto terminal block.

All switchgear used in starter feeder shall be type-2 co-ordinated. Manufacturer is required to submit manufacturers type-2 co-ordination chart for the make used.

All meters are digital type.

Panel shall be powder coated of approved shade with minimum 60 micron thickness.

ACB's/MCCB's in one particular panel shall be of one similar make.

Size of Voltmeter / Ammeter for incomer also, 96mm x 96mm flush mounted with shrouded terminal shall be used in the panel.

Bus bar chamber shall be kept at top of the all panels.

All bus bar shall be insulated with coloured PVC Sleeve i.e.RYB,BK as per colour code.

Internal wiring of panel shall be with size 2.5sqmm Flexible Copper Conductor for CT circuit and control wiring with 1.5 sqmm.

All Lift Panels transport section should not be more then 1000 mm.

In soft starter Vender should supply power contactor with aux. Contactor & All necessary accessories required etc. (As per BOQ & specification )

All indicating light shall be LED type .

Each vertical section of floor mounted panel shall have independent base frame (75mm x 40mm) size made out of 3 mm sheet steel (LT Panel & DG Panel).

All the makes shall be as per Client approved make list only.

Wherever only voltmeter & ammeter are required, the same may be provided in combined meter suitable for both parameter.

BLOCK PANELS

MAIN DISTIBUTION BOARD-(RESIDENTIAL TYPE-1)

INCOMER

1 Nos. 500Amp 36 KA 4P MCCB complete having microprocessor based over current, short circuit & earth fault protection incomer shall be complete with following.

METERING FOR EACH INCOMER

3 Nos. Cast resin current transformers of Class 1.0 for metering.

Three phase indicating lamps (LED type) with MCB.

ON OFF TRIP indicating lamps (LED type).

BUSBAR

1 Set of 600A, TPN Aluminum bus bars with colour coded sleeves.

OUTGOING UNITS

6 Nos. 125Amp TPN MCCB 16KA with thermal magnetic releases.

1 Nos. 100Amp TPN MCCB 16KA with thermal magnetic releases.

2 Nos. 63Amp TPN MCCB 16KA with thermal magnetic releases.

SUPPLY & INSTALLATION OF MAIN DISTIBUTION BOARD AS DESCRIBED ABOVE MAKE:- TRICOLITE, ADLEC, ADVANCE PANLES & SWITCHGEAR (P) LTD., SIMON FABRICATOR JAMMU, Electricfield

FLOOR PANEL-(RESIDENTIAL TYPE-1)

INCOMER

1 Nos. 125Amp 36 KA 4P MCCB complete having microprocessor based over current, short circuit & earth fault protection incomer shall be complete with following.

METERING FOR EACH INCOMER

3 Nos. Cast resin current transformers of Class 1.0 for metering.

Three phase indicating lamps (LED type) with MCB.

ON OFF TRIP indicating lamps (LED type).

BUSBAR

1 Set of 200A, TPN Aluminum bus bars with colour coded sleeves.

OUTGOING UNITS

5 Nos. 63Amp TPN MCCB 16KA with thermal magnetic releases.

SUPPLY & INSTALLATION OF MAIN DISTIBUTION BOARD AS DESCRIBED ABOVE MAKE:- TRICOLITE, ADLEC, ADVANCE PANLES & SWITCHGEAR (P) LTD., SIMON FABRICATOR JAMMU, Electricfield

FLOOR PANEL-(RESIDENTIAL TYPE-4)

INCOMER

1 Nos. 125Amp 36 KA 4P MCCB complete having microprocessor based over current, short circuit & earth fault protection incomer shall be complete with following.

METERING FOR EACH INCOMER

3 Nos. Cast resin current transformers of Class 1.0 for metering.

Three phase indicating lamps (LED type) with MCB.

ON OFF TRIP indicating lamps (LED type).

BUSBAR

1 Set of 200A, TPN Aluminum bus bars with colour coded sleeves.

OUTGOING UNITS

3 Nos. 63Amp TPN MCCB 16KA with thermal magnetic releases.

SUPPLY & INSTALLATION OF MAIN DISTIBUTION BOARD AS DESCRIBED ABOVE MAKE:- TRICOLITE, ADLEC, ADVANCE PANLES & SWITCHGEAR (P) LTD., SIMON FABRICATOR JAMMU, Electricfield

MAIN DISTIBUTION BOARD-(RESIDENTIAL TYPE-2)

INCOMER

1 Nos. 400Amp 36 KA 4P MCCB complete having microprocessor based over current, short circuit & earth fault protection incomer shall be complete with following.

METERING FOR EACH INCOMER

3 Nos. Cast resin current transformers of Class 1.0 for metering.

Three phase indicating lamps (LED type) with MCB.

ON OFF TRIP indicating lamps (LED type).

BUSBAR

1 Set of 600A, TPN Aluminum bus bars with colour coded sleeves.

OUTGOING UNITS

6 Nos. 125Amp TPN MCCB 16KA with thermal magnetic releases.

1 Nos. 100Amp TPN MCCB 16KA with thermal magnetic releases.

2 Nos. 63Amp TPN MCCB 16KA with thermal magnetic releases.

SUPPLY & INSTALLATION OF MAIN DISTIBUTION BOARD AS DESCRIBED ABOVE MAKE:- TRICOLITE, ADLEC, ADVANCE PANLES & SWITCHGEAR (P) LTD., SIMON FABRICATOR JAMMU, Electricfield

MAIN DISTIBUTION BOARD-(BOYS HOSTEL)

INCOMER

1 Nos. 500Amp 36 KA 4P MCCB complete having microprocessor based over current, short circuit & earth fault protection incomer shall be complete with following.

METERING FOR EACH INCOMER

3 Nos. Cast resin current transformers of Class 1.0 for metering.

Three phase indicating lamps (LED type) with MCB.

ON OFF TRIP indicating lamps (LED type).

BUSBAR

1 Set of 600A, TPN Aluminum bus bars with colour coded sleeves.

OUTGOING UNITS

5 Nos. 160Amp TPN MCCB 16KA with thermal magnetic releases.

2 Nos. 100Amp TPN MCCB 16KA with thermal magnetic releases.

4 Nos. 63Amp TPN MCCB 16KA with thermal magnetic releases.

SUPPLY & INSTALLATION OF MAIN DISTIBUTION BOARD AS DESCRIBED ABOVE MAKE:- TRICOLITE, ADLEC, ADVANCE PANLES & SWITCHGEAR (P) LTD., SIMON FABRICATOR JAMMU, Electricfield

FLOOR PANEL-(RESIDENTIAL TYPE-4) (BOYS HOSTEL)

INCOMER

1 Nos. 160Amp 36 KA 4P MCCB complete having microprocessor based over current, short circuit & earth fault protection incomer shall be complete with following.

METERING FOR EACH INCOMER

3 Nos. Cast resin current transformers of Class 1.0 for metering.

Three phase indicating lamps (LED type) with MCB.

ON OFF TRIP indicating lamps (LED type).

BUSBAR

1 Set of 200A, TPN Aluminum bus bars with colour coded sleeves.

OUTGOING UNITS

4 Nos. 63Amp TPN MCCB 16KA with thermal magnetic releases.

SUPPLY & INSTALLATION OF MAIN DISTIBUTION BOARD AS DESCRIBED ABOVE MAKE:- TRICOLITE, ADLEC, ADVANCE PANLES & SWITCHGEAR (P) LTD., SIMON FABRICATOR JAMMU, Electricfield

MAIN DISTIBUTION BOARD-(NURSE HOSTEL)

INCOMER

1 Nos. 315Amp 36 KA 4P MCCB complete having microprocessor based over current, short circuit & earth fault protection incomer shall be complete with following.

METERING FOR EACH INCOMER

3 Nos. Cast resin current transformers of Class 1.0 for metering.

Three phase indicating lamps (LED type) with MCB.

ON OFF TRIP indicating lamps (LED type).

BUSBAR

1 Set of 600A, TPN Aluminum bus bars with colour coded sleeves.

OUTGOING UNITS

4 Nos. 125Amp TPN MCCB 16KA with thermal magnetic releases.

1 Nos. 63Amp TPN MCCB 16KA with thermal magnetic releases.

SUPPLY & INSTALLATION OF MAIN DISTIBUTION BOARD AS DESCRIBED ABOVE MAKE:- TRICOLITE, ADLEC, ADVANCE PANLES & SWITCHGEAR (P) LTD., SIMON FABRICATOR JAMMU, Electricfield

MAIN DISTIBUTION BOARD-(AUDITRRIUM)

INCOMER

1 Nos. 500Amp 36 KA 4P MCCB complete having microprocessor based over current, short circuit & earth fault protection incomer shall be complete with following.

METERING FOR EACH INCOMER

3 Nos. Cast resin current transformers of Class 1.0 for metering.

Three phase indicating lamps (LED type) with MCB.

ON OFF TRIP indicating lamps (LED type).

BUSBAR

1 Set of 600A, TPN Aluminum bus bars with colour coded sleeves.

OUTGOING UNITS

3 Nos. 200Amp TPN MCCB 16KA with thermal magnetic releases.

8 Nos. 63Amp TPN MCCB 16KA with thermal magnetic releases.

SUPPLY & INSTALLATION OF MAIN DISTIBUTION BOARD AS DESCRIBED ABOVE MAKE:- TRICOLITE, ADLEC, ADVANCE PANLES & SWITCHGEAR (P) LTD., SIMON FABRICATOR JAMMU, Electricfield

LIFT PANEL

(Loc. Lift Machine Room)

Incoming:

One (1) No. 315A 4P on Load COS.

One (1) No. 315A TPN MCCB 36 Ka

Metering, Indication and Protection :

Three (3) Nos. phase indication lamps and three (3) Nos. status indication lamps with control MCB.

Busbar:

500A, TPN AL Bus Bar. Bus bar shall be insulated with heat shrinkable sleeves & shall be colour coaded.

Outgoings:

Two (2) Nos 63A 4P MCB

Four (4) Nos 100A TPN MCCB

One (1) Nos. 63A TPN MCCB

SUPPLY & INSTALLATION OF LIFT PANEL AS DESCRIBED ABOVE MAKE:- TRICOLITE, ADLEC, ADVANCE PANLES & SWITCHGEAR (P) LTD., SIMON FABRICATOR JAMMU, Electricfield

DISTRIBUTION BOARD

Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FRLS PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required.(But without MCB/ RCCB/RCBO/ Isolator) Make:- Schneider (Acti-9)/Siemens Beta Gaurd (8GB32)

12 Way (4+36), Double door

MCB FOR DB's

Supplying and fixing following rating, four pole, 415 V, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. MAKE:- SCHNIDER (ACTI - 9) /SIEMENS (BETA GUARD) /L&T(AU).

STATIC SINE WAVE INVERTER FOR COMMON AREA :

Design, manufacturing,Testing at works, supply erection, testing (at site) and commissioning of 1Ph AC input & 1Ph AC output Inverter system suitable for 230VAC, 50Hz supply, variation +/-1% , PF 0.8 as per specification. Make:- Microtek/Luminous/Numeric

Design, manufacturing, supply ,erection, testing (at site) and commissioning of One sets of SMF VRLA battery with each inverter, having back up time as mentioned below at full load,with interconnecting cables, cabinets and standard accessories as per specification and as required for the Inverter system.(12V Cells) with wire & assessories etc. Make:- Microtek/Luminous/Numeric

90 Minutes back up for 1.6 kVA

90 Minutes back up for 2 kVA

90 Minutes back up for 3 kVA

SUPPLY OF FIXTURES

Supply of the following light fixtures complete with housing, reflectors, complete with all accessories i.e. driver, lamp, holders etc. complete as required. Make:- Philips/Bajaj/Havells/Panasonic

Ceiling mounted luminaire Tube light with LED(Light Emitting Diode) system power: 10 W, luminous flux of luminaire 900lm, colour temperature of 4000K, neutral white, CRI>80, 230V constant current driver, 70% of luminous flux after 50,000 operating hours, energy efficient LEDs, direct light emission, aluminium housing powder coated white, satin micro liner prismatic diffuser, electronic control gear, Protection class I, IP20 L = 600mm, B = 21mm, H = 35mm,

Wall mounted Decorative, champagne gold finish fixture with plastic/matlic body suitable for 9/15 W LED lamp base.

Ceiling Mounted luminaire Zing with LED (Light Emitting Diode) system power: 18 W, Luminous flux of luminaire 1980 lm, Colour temperature of 4000 K, Neutral white,SDCM 3, R9 Value should be ≥0, CRI > 80, 230 V constant current driver, 70% of luminous flux after 50,000 operating hours; Energy efficient LEDs, Direct light emission, Luminaire housing in die-cast aluminium, Polyester powder-white coloured coat applied over a 5- stage pre-treatment, Opal protruded diffuser for homogenous light distribution, ZHLS (ZERO HALOGEN LOW SMOKE) internal wiring, Electronic control gear, Protection class II , IP 20, Ø = 180 mm,, H = 55 mm

Surface mounted bulkhead with LED (Light Emitting Diode) system power: 6 W, luminous flux of luminaire 800lm, colour temperature of 5700K, cool white, CRI>80, 230V, direct light emission, aluminium housing, powder coated white, opal diffuser for uniform illumination, electronic control gear, Protection class II, IP65, IK08, L=215mm, B=132mm, H=55mm

Recessed foot light Elixir with LED (Light Emitting Diode)system power: 03W, luminous flux of luminaire 210lm,3000K, warm white, CRI>80, 230V constant current driver,direct light emission, with reflector, aluminium housingpolyester powder coated white applied over a 5-stage pre-treatment, electronic control gear, Protection class II,IP65, L = 70mm, B = 32mm, H = 22mm,

Ceiling/wall mounted luminaire Vela S with LED(Light Emitting Diode) system power: 18 W, luminous flux of luminaire 1980 lm, colour temperature of 5700K, cool white, CRI>80, 230V constant current driver, 70% of luminous flux after 50,000 operating hours, energy efficient LEDs, direct light emission, aluminium housing powder coated white, satin micro liner prismatic diffuser, electronic control gear, Protection class I, IP20 L = 1200mm,

1200 Dia Fan

225MM Dia Ex. Fan

LT NORMAL CABLE

Supplying of following sizes of XLPE/ PVC insulated Aluminum/ Copper conductor and Armoured, overall PVC sheathed 1.1 KV grade cables conforming to relevant IS code and technical specifications. MAKE:- POLYCAB/HAVELLS/CCI

XLPE insulated Al. Ar.Cable

3.5C x 300 sq.mm.

3.5C x 240 sq.mm.

3.5C x 70 sq.mm.

3.5C x 50 sq.mm.

3.5C x 35 sq.mm.

4C x 25 sq.mm.

4C x 16 sq.mm.

4C x 10 sq.mm.

VIDEO SURVEILLANCE SYSTEM (IP CCTV) Make:- Axis/Sony/Bosch/Pelco

Supply, installation, testing & Commissioning of 1080p Dome camera with 1/2.8‑inch CMOS, Effective pixels 1920 x 1080 (2MP), 30fps, Sensitivity – (Measured according to IEC 62676 Part 5 (1/30, F1.6) Color 0.06 lx Mono 0.02 lx With IR 0.0 lx, 120 dB Dynamic range, Electronic Day/Night, Automatic Electronic Shutter (AES), H.265, H.264 MP (Main Profile); M-JPEG Video compression, White balance, Backlight Compensation, Privacy Mask,Rule based alarms and tracking, Line crossing, Enter /leave field, Follow route, Loitering, Idle / removed object, People counting, Crowd density estimation, 3D tracking based on Duration, Size, Aspect ratio v/h, Speed, Direction, Color, Object classes (Upright persons, Bikes, Cars, Trucks), 3.2 to 10 mm Automatic Varifocal (AVF) lens, MicroSD card slot for edge recording, Motion, tamper and audio detection, FTP, IR range upto 30mtrs Dropbox and e-mail applications, 3 axis adjustment, ONVIF Profile S & G & T, PoE, IP66, IK10, CE, FCC, UL certified. SD card support up to 2TB.

Supply, installation, testing & Commissioning of 1080p HD IR PTZ Camera with 1/2.8" progressive scan CMOS, Effective pixels 1945 (H) x 1097 (V) (approximately 2.13M pixels), 30x Optical Zoom (4.5 mm–135 mm)(F1.6 - F4.4), 16X Digital Zoom, Minimum Illumination- Color: 0.0186 Lux , B/W: 0.004 lux, IR: 0 lux; IR distance 180 m (590 ft) (Detection); 120dB WDR, H.265, H.264, MJPEG streams, Intelligent Dynamic Noise Reduction, BLC, White Balance, Pan Range 360° continuous, Tilt Range -90° to 3° (Auto-flip 186°), Pan/Tilt Modes - Pan: 0.1°/s - 240°/s; Tilt: 0.1°/s - 120°/s, Presets 256, Tours, Audio- 1/1 Channel In/Out, Micro SD card support up to, 32 individually configurable privacy masks, Alarm inputs/outputs - 2/1, Dual Power options, Any object, Object in field, Crossing line, Entering field, Leaving field, Loitering, Following route, Idle object, Removed object, Counter, Occupancy, Crowd detection, Condition change, Similarity search, Tampering, Object filters based on Duration, Size, Aspect ratio v/h, Speed, Direction, Color, Object classes (Upright persons, Bikes, Cars, Trucks), IP66 , ONVIF Profiles S & G & T, FCC, CE, UL Certified. SD card support up to 2TB.

Supply, installation and commissioning of Remote compact keyboard, variable speed, USB Joystick Control, for PTZ camera/NVR, UL Listed.

SITC of Rack Server, Windows 2019, 16 GB DDR4 ECC, Intel® Xeon® Silver 4210, OS RAID1, Idrac,1G NVIDIA Quadro P620 (2GB) video card, 450mbps Bandwidth, 3 year warranty

Supply installation Testing and Commissioning of Video Management Software, All Cameras shall be of same make *web based client allows viewing and exporting video without installing any software. *Imports users and roles from existing LDAP servers to reduce administrative overhead,and enables single sign-on (SSO) *Capable of listening for ASCII commands *Check on VMS and camera health using SNMP *Supports IPv4 and IPv6 cameras *Enables and supports Risk Management Framework (RMF),incorporates FIPS 140-3 validated cryptographic modules *TLS-based encryption over HTTPS

Supply & Installation of Surveillance harddrive 12 TB

Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz); Memory: 4GB, NON-ECC, 1600MHZ; RAM: 4GB (1x4GB) Non-ECC DDR3 1600MHz SDRAM Memory; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; 20" TFT Monitor; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit.

SITC 43 inch 4K Smart Monitor for surveillance.

Supplying and fixing Patch Chord - 1 Mtr with appropriate terminal connectors (Used for CCTV I/O connection)

Supply of HDMI Cable 1.5 meters

Supply , Installtion , Testing and Comissioning of following sizes wall mount 4U rack , 2 cable managers.This rack to be used for CCTV, DATA networking also and to be placed in shaft.

SITC 8-Port Gigabit PoE Smart Managed Pro Switch, 8-Port 53 W Power-Over-Ethernet, ProSAFE Lifetime Protection.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. MAKE:- POLYBACK/Precision/AKG/Anchor/BEC)

Supplying, laying, marking, making connections and testing of CAT-6 cable . (For CCTV Camera ) Make:- CCI/Havells/Polycab/Legrand.

Supply, installation, testing & commissioning of IP66 Box ( 600 X 400 mm) with bottom lowers for heat dissipation for housing Switches, media converter, power supply units for camera connecting over fiber optics( 2 cameras connected to 1 outdoor box).

Supply & Erection of 75mm dia GI poles suitable for mounting camera required. Provision to be made for cable entry and connection for camera with all fixing arrangement to the pole etc, complete as required.

6.0 m mounting height

Supply and laying of following DWC HDPE P1/2C as per IS 14930-2001(Part-2) at road crossings including excavation, refilling, cutting the road and making good for the same with sealing of ends as required.

63 mm inner dia

100 mm inner dia

Supply, laying, termination, testing and commissioning of following single mode armored- uni tube fiber optic cable complete as required.

6 core fiber optic cable

Supply, laying, termination, testing and commissioning of following armored cable on existing cable tray including the cost of making of connections, complete as required.:-

4 pair CAT 6 Cable

2 core 1.5 Sq.mm.copper power cable

jai prakash and sons

SRISHTI CONSTRUCTIONS

N S Associates PVt Ltd

A S ENTERPRISE

RSB PROJECTS LIMITED

Rabina Enterprises Pvt Ltd