Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹10.4 LAccepted-AOC HARI OM BHAWAN CIRCULAR ROAD UPPER KAITHU SHIMLA | L1 | Accepted-AOC L1 | |
| 2 | L2₹10.8 L+₹39,761 (3.81%)Rejected-AOC SCO 10 BLOCK NO 2 SDA COMPLEX KASUMPTI SHIMLA 09 | SHIMLA | HIMACHAL PRADESH | 171009 | L2 | Rejected-AOC L2 |
Tender Value
Refer Docs
Closing Date
19 Jun 2021, 5:00 pmClosed
XEN Electrical division No. 1 Shimla-9
The Executive Engineer Electrical Division No-1 HPPWD Shimla-9
SH Providing additional boiler and central heating piping therein
2021_PWD_48345_1
Electrical Div.No1PWD Shimla 2021-22-693-98 dt.02-
Open Tender
Electrical Works
Item Rate
365 days
SHIMLA
Please refer Tender documents.
7 documents required · 7 mandatory
₹500
E.E.Electrical Division No-I Shimla-9
22 May 2022
10 Jun 2021
21 Jun 2021
10 Jun 2021
19 Jun 2021
10 Jun 2021
Amount
Supply installation testing and commissioning of electric element type hot water boiler /generator complete with s tank, cylindrical shell 10mm with dished ends,sheet metal enclosure, integral electrical and control panel i/c all operational and safety controls. The Boiler shall be Horizontal type capacity of 250KW capacity, bank will consist five steps with micro processor intelligent step controller and reverse flow sensor, i/c making cc foudation and complete in all respects:MAKE: Rapid Cool , Model 250DS/ Dyna Flow or any other approved by engineer in charge
Supplying, installation, testing & commissioning of fancy compact type, Hiwall/ Floor mounted power coated hot water Forced air radiator unit of following capacity free air discharge capacity complete with fan blower suitable for operation on single phase 230 V 50 Hz AC supply complete with finned hot water finned coil. air filter washable complete with thermostate modulating valve / 3/4 " brass ball valve with strainer on inlet and 3/4" brass ball valve on outlet complete as required make airef,ventair,edgetech or any other approved by engineer in charge
Supply, installation, testing and commissioning of hot water piping and fittings complete with supports, hangers and specified insulation thickness. All piping shall be black mild steel Class C, ISI marked with fitting. The unit rate of piping shall include this support arrangement and hangers i/c wooden saddles where required under insulation at support points.The piping shall be insulated with 80Kg/ M.Cub. section density fiberglass insulation finally covered with 26 gauge Al. Cladding for outside and 6mm plaster for inside complete as required
80 mm pipe with 75 mm insulation.
40 mm pipe with 50 mm insulation.
32 mm pipe with 50 mm insulation.
25 mm pipe with 50 mm insulation.
19 mm pipe with 50 mm insulation.
Supply, installation, testing and commissioning of Gate valves/ Sluice valves ISI marked, with flanges or screwed ends as required. Valves 65 mm and above shall of C.I. Body , with flanged ends and gunmetal trim, non-rising spindles ,P N. 1.6 and i/c flanges where required and valves upto 50mm shall be gunmetal non rising stem, integral seat, body test pressure 50kgf/cm Hyd (MAKE: KRILOSKAR/SANT/LEADER or any other approved by engineer in charge
UNITECH ENGINEERS
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .