Special repair for House No. 43, on Kunjpura road Karnal

Amount

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the wall is not to be dismantlled :- (HSR 8.18) a) Doors

b) Windows.

Scrapping white wash and colour wash[HSR 8.32(a)]

Scraping of cement plaster [HSR 8.32(c)]

Dismantling white or coloured glazed tiles (to be carefully removed) [HSR 8.38]

Terracing consisting of tiles 22.86 cm x 11.43 cm x 3.81cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and an other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 Kg. per sqm on top of RCC the slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13).

Precast chequered tiles of 20 mm thickness in ordinary grey cement without chips laid on 20 mm thick bed of cement course sand mortar 1:3 with neat cement slurry between joints and over the base in floors , treads of steps and landings [HSR 14.45]

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, JOHNSONS & RAK. (HSR 14.89)

Providing and fixing vitrified tiles of size 600 mm x 600mm of approved make in skriting / dado laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, JOHNSONS & RAK. (HSR 14.90)

Providing and fixing ceramic tiles / anti skid tiles of size 400 mm x 400mm or above size of approved make in flooring, laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JOHNSONS. (HSR 14.91)

Providing & fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (HSR 14.92) b) Size of ceramic Glazed tiles 300 x 450 mm

12 mm thick cement plaster 1 : 4 on walls ( HSR 15.5 )

Cement pointing 1:3 deep variety on brick and tile work. (HSR 15.61)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.2).

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.3).

Preparation of plastered surface for oil bound distemper including sand papering the surface, applying one coat of linseed oil, and filling with approved quality filler, consisting of white lead , linseed oil,varnish and chalk mitti including finishing the surface to the required finish complete. (HSR 16.52)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.58).

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (b)].

Providing and fixing hard drawn steel wire fabric 75mm x 25mm rectangular mesh with 3.25 mm dia wire fixed on chowakts with 25mm thick kail wood cover moulding of full width. [HSR 17.29]

Wire gauze commercial hard wood such as hollock,champ, chikrassy etc.(Non coniferous timber other than teak conforming to I.S. specification No.1003 kiln seasoned) door and window shutters without springs housed in chowkats including chocks, iron hinges and screws, etc., complete fixed in position (excluding the cost of tower bolts and handles but including the labour for fixing the same)- a) 30mm thick (HSR 17.31 (a)

Cup board shutter of commercial hard wood such as hollock,champ, chikrassy chaplash etc.(Non coniferous timber other than teak conforming to I.S. specification No.1003 kiln seasoned) excluding chowkat but with commercial ply wood panels or faced on one side including iron hinges and screws fixed in position (excluding the cost of handles, tower bolts, hasp with stmaple, but including the labour for fixing the same- (b) 25mm thick. [HSR 17.32(b)]

Supplying and fixing glass panes with moulding of commercial hard wood such as hollock, champ, chikrassy and chaplash etc. ( Non coniferous timber other than teak, conforming to I.S. specification No. 1003 kiln seasoned )- ( c) 4 mm thick ( glazing area above 55 sq dm but upto 84 sq dm of each pane) [HSR 17.36( c)]

Providing and fixing 150mm hasps and staples with necessary screws ,etc., complete ( c ) iron [HSR 17.78 ( c ) ]

Providing and fixing sliding bolt with nuts and screws, etc., complete (c) iron [HSR 17.83(c)] size 250 mm x 16 mm

Factory manufactured panelled door or glazed window, shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash, etc.,(non-coniferous timber other than teak, conforming to I.S. specification No. 1003, kiln seasoned), with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks/cleats, stops, nails etc., complete, fixed in position (execluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) [HSR 17.90 b) 35mm thick

Wrought iron and mild steel(using angles, flats ,square bars , tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position (HSR 18.12)

Pressed steel sheet frames (chowkats ), consisting of 2mm thick steel sheet of the specified section,including iron lugs(hold fasts) iron hinges conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for fillings in the frame, and cement concrete 1:3:6 for lugs complete (HSR 18.34) a) Door and Window frame of size 89 mm x 50 mm with 40 mm wide single rebate

b) Door and window frame of size 76 mm x 38 mm with 35 mm wide single rebate

c) Door and Window frame of size 127 mm x 50 mm with 40 mm wide double rebate

Cutting holes upto 23cm through stone masonry or brick work in cement walls for pipes and making good. [HSR 28.24] a) 11.43 cm thickness of walls

b) 22.86 cm thickness of walls

Cutting Holes upto 23 CM square for Pipes in flooring and roofs of bricks tiles with lime concrete and making good Including, repointing, replastering and colour or white washing where required. [HSR 28.25] (b) 115 mm thickness of floor

Providing and fixing in position best indian make (to the approved of the Engineer-in-Charge) European type water closet suit with non-concealed 'P' or 'S' trap with or without vent and all other necessary fittings as fully described in item no. 30.3 above [HSR 30.4 (ii)] Single Colour

Providing and fixing in position best Indian make (ordinary)lavatory suites, consisting of Lavatory in vitreous chinaware size as given below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary. R.S. or C.I. Brackets for building into wall including painting, 32mm C.P. brass waste with C.P brass, 15mm C.P. brass screw down pillar tap all fitting best Indian make complete in all respect including cutting and making good the walls floors and painting of fittings etc. [HSR 30.41] White (v) Size 560mm × 450 with one no. tape

b) Single Colour (v) Size 560 mm x 400 mm with one no. tap

Providing and fixing in position best Indian make Pedestal fittings of vitreous chinaware complete (as required by the Engineer-in-charge) [HSR 30.44] (ii) Single colour

Providing and fixing in position best Indian make C.P. brass three tap holes mixer with pop-up-waste instead of one no. pillar tap and C.P. waste [HSR 30.46 b]

Providing and fixing in position 32mm dia G.I. Waste pipe embedded in wall or lead waste pipe (weighing 3.47kg. per metre and 2.8 mm thick) upto floor level including cost of wipped solder joint etc., complete (as required by the Engineer-in-charge)[HSR 30.48]

Providing and fixing in position best quality stainless steel sinks with complete fittings as fully described in item No.30.51 above [HSR 30.53] (a) size 600mm x 450mm x 200mm

Providing and fixing in position best Indian make shower with 15 or 20 i/d in-let. [HSR 30.66] d) C.P. Brass with telephonic shower

Providing and fixing in position best Indian make paper holders fixed into wall with C.P. brass screws complete in all respects including cutting and making good the walls etc. [HSR 30.67] (c) RECESSED VITREOUS CHINAWARE (ii) Single colour

Providing and fixing in position best Indian make Towel rails fixed in with rawl plugs embedded in walls with C.P. brass screws. Complete in all respect including cutting and making good the walls etc. [HSR 30.68] (d) C.P. brass two swivel towel rail 400 mm long

Providing and fixing in position glass shelf fixed in with rawl plugs with C.P. brass screws complete including cutting and making goods the walls etc. [HSR 30.69] a) With C.P. brass brackets and guard rail (i) 600 mm x 125 mm

Providing and fixing in position best Indian make bevelled edge 5.5mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 Nos. chromium plated brass screws and washers over rubber washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P brass screws (as required by the Engineer-in-charge) complete including cutting and making good the walls etc. [HSR 30.71] b) With vitreous china frame of size 530 mm X 430 mm (ii) Single colour

Providing and fixing in position 15mm i/d C.P.bras bib cocks of best quality (as required by the Engineer-in-charge). [HSR 30.75] c) Bib cock

Providing and fixing in position C.P. brass stop cock (as approved by the Engineer-in-charge). [HSR 30.76] a) 15mm stop cock (i) Stop cock male and female end

ii) Concealed stop cock with flange

Providing and fixing in position best Indian make flexible tube connection [HSR 30.82] b C.P. Brass (i) 15mm x 300 mm]

Providing and fixing in position automatic brass ball valves in tanks [HSR 30.110] b) WITH PEASTIC BALL (ii) 20mm i/d

Providing and fixing HDPE water storage tanks of Sintex, Diplast, O.K., Supreme make with covers / lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with sutiable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in-Charge. (except civil work). (HSR 30.119) 1000 Ltr. capacity.

Providing & fixing PVC Sheet for shed in all respect to the entire satisfaction of Engineer-in-Charge. ( N.S)

Recovery items:- The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Dismantiling of bricks and Removing of Door and windos in the DNIT. In case it is not possible to use this material on the work, the agency can take away this material after approval from employer. This material will be issued at the price quoted by the agency. However the reserve price is as under:- i) Door @ 800/- Each

ii) Windows @ 500/- Each Note:- All quantities of the above materials have been worked out on the basis of theoretical quantities laid on this building. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement after actual dismantling and if material after dismantling is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price. Note:- 1. In case of any difference in the unit & nomenclature of any of the HSR Items of Civil, P.H. work depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable. 2. Only reputed make material will be used (make/brand exhibited in HSR and exhibited in approved standard document) as approved by Engineer-in-charge, while executing various items/works at site.

Sh. Bharat Sharma SO Sh. Pawan Sharma

M/s Ashwani Kumar Contractor