ARC of Maintenance of Various Gardens

Supply and fixing different type of steel pre-fabricated garden bench/ jhula/ slides and other children play items made of steel duly painted as per approved design and specifications by engineer in-charge made of MS pipe, Flats, rectangular hollow section or other steel sections duly welded and or nut bolted where ever required, rubbing and buffing welded joints to make safe for use of children and painted in approved pattern complete as required.

Grassing with 'Doobs' grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for moving including supplying good earth if needed. (The good earth shall be paid separately)

In rows 7.5 cm apart in either direction

Planting permanent hedges including digging of trenches, 60 cm wide and 45 cm deep, refilling the excavated earth mixed with farmyard manure, supplied at the rate of 4.65 cum per 100 metres and supplying and planting hedge plants at 30 cm apart.

Providing and fixing of 60mm thick precast cement concrete interlocking paver block casted with rubber moulds in approved reflective colour and design having minimum compressive strength of 300 kg/ sq cm. The CC paving blocks be laid on average 50mm thick bed of coarse sand and the joint is to be filled with fine sand. Laying procedure on compacted sub-base as defined. Complete job is to be executed as per the instruction of Engineer in-charge. The rates to be inclusive of all lead & Lifts etc. complete as per specifications.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level:

1:1:3 (1 Cement: 1% coarse sand: 3 graded stone aggregate 20 mm nominal size).

Providing 1.20 metre high fencing with angle iron posts 50 mm x 50 mm x 6 mm at 3 metre center to center with 0.40 metre embedded in M15 grade cement concrete, corner, end and every 10th post to be strutted, provided with welded steel wire fabric of 75 mm x 50 mm mesh or 75 mm x 25 mm mesh and fixed to iron posts by flat iron 50 x 5 mm and bolts etc. complete in all respects including all material, labour.

Supplying, erecting and fixing in position specified precast RCC bench made of RCC grade M-30 consisting of 2 Nos. “L” shaped base support of thickness 100 mm back height 1000mm, front height 450 mm, base width 420mm and 5 Nos. RCC planks of size of 1500x100 x 50 mm and 1 Nos RCC planks of 150x200x50mm including joining all parts with galvanised nuts and bolts of suitable size. All bolts to be sealed after assembly with nice finish and appearance and level complete in all respect as per direction of engineer in-charge. Every bench should have a manufacturer’s logo of appropriate size Engraved at suitable place.

Supplying and stacking good earth at site of work. Note: 1) Loading, unloading and carriage to be paid extra as per actual lead. 2) Earth measured in stacks will be reduced by 20% foe payment

Finishing walls with water proofing cement paint of required shade :

Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat.

Painting two coats on specified surface with synthetic enamel paint of approved brand and shade, after thorough cleaning and necessary filling to give even shade as per clause 803 of MoRT&H Specification including all material, labour.

On steel surface

Supply of P.V.C. hose pipe of different sizes at store including transportation etc complete :

Supply of Insecticides & Pesticides at store in dust / liquid form complete.

Methyl Parathion 2%. 50 kg bag

Karathion (Liquid). 250ml packing

Metacid (Liquid).

Roger (Liquid).

Cholorophyriphos 20 Ec.

Bauiston 50 %. 100 grams packing

Supply of Chemical Fertilizers at store in bags weighing 50 kg. each including loading unloading & transporation etc.

Super Phosphate

Murrate of Photash

Supply of Graden Tools & Implements at store complete :

Spade weighing 1.5 kg. with Handle.

Khurpa weighing 500 gm with Handle.

Gurvana weighing 800 gm. with Handle

Hedge Shear (kamani Steel)

Wrought iron and mild steel welded work) (using angles, square bars, tees and channel grills, grating frames, gates and tree guards of any size and design etc. including cost of screens and welding rods or bolts and nuts complete fixed in position but without the cost of excavation and concrete for fixing which will be paid separately.

Providing and fixing M. S. tree guard 45 cm square in plan, height 1.20 metre above ground level and 0.40 metre below ground level.The vertical members shall consist of four nos angle iron of size 25x25x3 mm, 1.6 m long, one at each corner and 8 nos flat iron of size 25x3 mm, 1.2 m long. The vertical members shall be welded to 4 nos 25x6 mm M. S. flats placed horizontally around the vertical member of the cage. The tree guard shall be painted with two or more coats of synthetic enamel paint of approved brand and manufacture over a coat of primer, complete in all respect.

Supply and planting following species best quality container grown healthy trees of 2 mt. min. height, well established & free from disease at site in 0.90 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, backfilling the hole watering etc as required.

Plumeria alba ( Champa)

Gulmohar(Delonix regia)

Neem(Azadirachta indica)

Jacaranda mimosifolia (Neelli Gulmohar)

Bauhinia blakeana (Arckid)

Erythrina variegata (Lantern Tree)

Bottle Brush(Callistemon Lanciolatous)

Mangifera indica (Mango)

Yucca

Bignonia Venusta

Supply of different sized pots at site store including loading unloading & transportation etc. complete.

Cement pot / Plastic pot 375 mm size

Cement pot / Plastic pot 450 mm size

Cement pot / Plastic pot 525 mm size

Crane 15 tonne capacity

Random rubble masonry with hard stone in foundation and plinth :

Cement mortar 1:6 (1 cement : 6 coarse sand)

Extra for random rubble masonry with hard stone in superstructure above plinth level and upto two stories.

SURFING BOARD Providing and fixing of Surfing Board of size not less than 1000mm (Length) x 600mm (Width) x 1400mm (Height), to build up the muscle groups of the waist, enhance the body coordination and flexibility. The main structure frame shall be made from G.L. pipe minimum of 80NB "C" class welded with M.S. round base plate atleast 0250 mm & 10mm thick. The footrests shall be made from high quality fiber reinforced plastic material. High tensile steel with galvanized nut bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powder of Ackzonoble/Berger/Nerolac with minimum 60 to 70 micron thickness, complete in all respect including fixing the M.S, boldfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 1. (The cement concrete and excavation work shall be paid separately).

CROSS TRAINER Providing and fixing of Cross trainer of size not less than 1320mm (Length) x 600mm (Width) x 1750mm. (Height), to enhance the mobility of upper and lower limbs and improve the flexibility of joints. The main structure frame shall be made from G.1. pipe minimum of 80NB "CC" class welded with M.S. round base plate atleast 0250 mm & 10mm thick. The Handle Frame shall be made up of atleast 25NB "C" Class G.I. Pipe. The footrests shall be made from Aluminum casting material of size not less than 130 mm X 310mmX5mm thickness and mounted on M.S. Plate of Size 130mmx310mmx3mm thick. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders of Ackzonoble/ Berger/Nerolac Paints with 60 to 70 Micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 2. (The cement concrete and excavation work shall be paid separately).

THAI-CHI SPINNER (2 WHEEL) Providing and fixing of Thi-Chi spinner (2 Wheel) of size not less than 700mm (Length) x 1000mm (Width) x 1280mm (Height), to increase mobility of shoulder -elbow and hip-knee. The main structure frame shall be made from G.1. pipe minimum of 80NB "C" class welded with M.S, round base plate atleast 0250 mm & 10mm thick, High tensile S.S. nut bolts shall be used for assembly. The powder coating shall be done with pure Polyester powders from Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 3. (The cement concrete and excavation work shall be paid separately).

SEATED PULLER Providing and fixing of Seated Puller of size not less than 1900mm (Length) x 740mm (Width) x 1920mm. (Height), to enhance the strength of upper limbs and the muscles in chest and back and promote cardio-pulmonary function. The main structure frame shall be made from G.I. pipe minimum of 80NB "C" class welded with M.S. round base plate atleast 0250 mm & 10mm thick. The handle frame shall be minimum of 32NB "C" class G.I. pipe. The seat frame minimum of 32NB "C" class G.I. pipe, Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders of Ackzonoble Berger Nerolac Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 4. (The cement concrete and excavation work shall be paid separately).

LEG PRESS Providing and fixing of Leg Press of size not less than 1840mm (Length) 360mm (Width) x 1560mm. (Height), to build up the muscles of thigh and enhance the strength of waist. The main structure frame shall be made from G.I. pipe minimum of 80NB "C" class welded with M.S. round hase plate atleast 0250 mm & 10mm thick. The Sleeve frame minimum of 100 OD and of M.S. Seamless Pipe with thickness 5mm. This sleeve should be disassembled from main frame. The footrests shall be made from casted Aluminum material, having sizes minimum of 130mm X 310mm X 5mm thick. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nut bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powder of Ackzonoble/ Berger/Nerolac with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 5. (The cement concrete and excavation work shall be paid separately).

SIT UP BOARD DOUBLE Providing and fixing of Sit up Board double of size not less than 1760mm (Length) x 1140mm (Width) x 660mm (Height), to enhance the flexibility of whole body. The main structure frame shall be made from G.1. pipe minimum of 80NB "C" class welded with M.S. round base plate atleast 0250 mm & 10mm thick. The remaining frame of the sit up board minimum of 32mm NB shall be made from "C" class Gl pipe. The powder coating shall be done with Pure Polyester powder Ackzonoble Berger Nerolac Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 6. (The cement concrete and excavation work shall be paid separately).

CHEST PRESS Providing and fixing of Chest Press of size not less than 2000mm (Length) x 710mm (Width) x 2200mm. (Height), to enhance the strength of upper limbs and the muscles in chest & back and promote cardio pulmonary function. The main structure frame shall be made from G.I. pipe minimum of 80NB "C" class welded with M.S. round base plate atleast 0250 mm & 10mm thick. The handle frame shall be made up from atleast 32NB "C" class G.I. pipe. The seats and Back rests to be fitted on the outer frames shall be made up of M.S. Sheet of size not less than 330mm X 300 mmX2mm thickness. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts & holts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 7. (The cement concrete and excavation work shall be paid separately).

POMMEL HORSE Providing and fixing of Pommel Horse of size not less than 2150mm (Length) x 800mm (Width) x 800mm. (Height), to enhance the flexibility of lower limbs, waist and abdomen. The main structure frame shall be made from G.I. pipe minimum of 80NB "C" class welded with M.S. round base plate atleast 0250 mm & 10mm thick. The handle frame be minimum of 32NB shall be made from "C" Class G.J. pipe. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powder Ackzonoble/ Berger/ Nerolac Paints with 60 to70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 8. (The cement concrete and excavation work shall be paid separately).

DOUBLE STANDING TWISTER Providing and fixing of Double Twister Standing of size not less than 1500mm (Length) x 600mm (Width) x 1300mm. (Height), to enhance flexibility of waist. The main structure frame shall be made from G.I. pipe minimum of 80NB "C" class welded with M.S. round hase plate atleast 0250 mm & 10mm thick. The handle frame is minimum of 25NB shall he made from "C" class G.L. pipe. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round Plate of minimum size 0300mm and 10mm thick. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble/Berger/Nerolac Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 9. (The cement concrete and excavation work shall be paid separately).

STANDING SEATING TWISTER Providing and fixing of Seating & Standing Twister of size not less than 1700mm (Length) x 540mm (Width) x 1250mm. (Height), to enhance flexibility of waist, suitable for people of different ages except children. The main structure frame shall be made from G.I. pipe minimum of 80NB "C" class welded with M.S. round base plate atleast 0250 mm & 10mm thick. The bottom frame of the Seating & Standing twister he atleast of 32 NB, 50 NB, and 25 NB shall be made from "C" class G.I. pipe. The handle frame of Seating & Standing twister of minimum 25 NB & Foot resting frame of seating side shall be made from "C" class G.1. pipe minimum of 25mm NB. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round Plate of minimum size 300mm diameter and 10mm thickness. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done by Pure Polyester powder of Ackzonoble/ Berger/Nerolac Paint with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 10. (The cement concrete and excavation work shall be paid separately).

CHEST CUM SHOULDER PRESS Providing and fixing of Chest Press Cum Seated Puller of size not less than 2000mm (Length) x 710mm (Width) x 2200mm (Height), to enhance the strength of upper limbs and the muscles in chest and shoulder. The main structure frame shall be made from G.I. pipe minimum of 80NB "C" class welded with M.S. round base plate atleast 0250 mm & 10mm thick. The seats and Back rests to be fitted on the outer frames shall be made up minimum of M.S. Sheet of size 330 mm X 300 mmX2num thickness. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 11. (The cement concrete and excavation work shall be paid separately).

PUSH UP BARS Providing and fixing of Push Up Bars of size not less than 1220mm (Length) x 550mm (Width) x 1700mm. (Height), To enhance the strength and stemina of the body. The main structure frame shall be made from G.1. pipe minimum of 80NB "C" class welded with M.S. round base plate atleast 0250 mm & 10mm thick. The handle frame minimum of 25 NB shall be made from "C" Class G.I. pipe. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done with Pure Each Polyester powders of Ackzonoble/ Berger Nerolac Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 12. (The cement concrete and excavation work shall be paid separately).

Supply and fixing of Instruction board of size 4'x 6' made of digital vinyl print with gloss lamination & pasted on 3mm ACP sheet fixed over 2.0 mm thick MS sheet, framed on 32 mm dia MS pipe, supported on 50mm dia. MS pipe which goes 600mm below ground level with hold fast including welding and painting.Design and drawing as per photograph no. 13, all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately).

Providing, lowering, laying in trenches, aligning, fixing in position and jointing socketed rubber gasket type ISI marked uPVC pipes of Class III (6 Kg/sqcm) suitable for potable water with rubber ring joints (as per IS 4985-2000) of following outer dia with all accessories as per Technical Specifications and as per direction of Engineer 32 mm dia

Supply and fixing of 360 degree Rotating Water Sprinkler with 3 arms watering Garden plants

ROTO WAVE SLIDE – (1.5 m) Age Group :- 4 – 12 yrs. Product Area :- 4.6 m x 0.6 m Safe Play Area :- 5.6 m x 1.6 m The Wave Slide is made up of Linear Low Density Poly Ethylene by Rotational molding process in one piece having shell thickness of 4-5 mm with UV stabilized. The slide is supported on a center support of 80 NB GI pipe. The landing supports of the slide are supported by two 20 NB pipes. The slide ladder is made up of 25 NB GI pipe & the ladder hand-railing is made up of 15 NB and 20 NB pipes respectively. The triangular steps of the ladder are made up of 16 SWG GI sheets. The safety railing of the ladder is made up of LLDPE in Rotational molding process. The wave slide platform is made up of 14SWG GI sheet. The trade and riser of the ladder are designed in such a way it won’t entrap child’s foot while playing. All the sharp edges and corners are properly grinded to give smooth finish so that children are not hurt while playing on it. This slide is designed as per ASTM & EN standards which are globally accepted standards. The work should Comply Strictly with the detailed drawing & specification on page no. )

ROTO WAVE SLIDE (2.1 m) Age Group: - 4 – 12 yrs. Product Area :- 5.5 m x 1.0 m Safe Play Area :- 6.5 m x 2.0 m The Wave Slide is made up of Linear Low Density Poly Ethylene by Rotational molding process in one piece having shell thickness of 4-5 mm with UV stabilized. The slide is supported on a center support of 80 NB GI pipe. The landing supports of the slide are supported by two 20 NB pipes. The slide ladder is made up of 25 NB GI pipe & the ladder hand-railing is made up of 15 NB and 20 NB pipes respectively. The triangular steps of the ladder are made up of 16 SWG GI sheets. The safety railing of the ladder is made up of LLDPE in Rotational molding process. The wave slide platform is made up of 14SWG GI sheet. The trade and riser of the ladder are designed in such a way it won’t entrap child’s foot while playing. All the sharp edges and corners are properly grinded to give smooth finish so that children are not hurt while playing on it. This slide is designed as per ASTM & EN standards which are globally accepted standards. The work should Comply Strictly with the detailed drawing & specification on page no. ) .

Roto spiral slide 5’ht: Age Group :- 4 – 12 yrs. Product Area :- 3.0 m x 2.0 m ◻ Safe Play Area :- 4.0 m x 3.0 m The spiral tube slide is made up by bi-axial rotational moulding process with the wall thicknessof 5mm with UV stabilized LINEAR LOW DENSITY POLYETHYLENE material which gives it aattractive look. This slide is designed as per ASTM & EN standards which is globally acceptedStandards. The supports for the slide is designed by keeping in mind the strength and as well asthe aesthetics of the slide. The work should Comply Strictly with the detailed drawing & specification on page no. )

DOUBLE ARC SWING Age Group :- 4 – 12 yrs. Product Area :- 3.2 m x 1.5 m Safe Play Area :- 4.2 m x 2.5 m The arch shaped side frame of the swing is made up of 80 NB GI pipe "B" Class and top pipe is made up of 50 NB GI pipe "B" Class. The frame is powder coated to give an esthetic look. The two swings are made up of 10 mm thick anti skid chequered reinforced rubber top. The belt seat is suspended on 6 mm rubber coated GI chain. The ball bearings are mounted inside a specially designed nylon clamp. as per direction of site Engineer Incharge The work should Comply Strictly with the detailed drawing & specification on page no. )

MULTI SEATER SEE-SAW Age Group :- 3 – 10 yrs. Product Area :- 0.5 m x 3.0 m Safe Play Area :- 1.5 m x 4.0 m The MS See saw comprises four FRP seats. The lever is consisted of 20 nb and 80 nb powder coated gi pipes. The bearing used in this item is heavy duty nylon bush type. The stand for see saw is made using 50 NB GI pipe. (The work should Comply Strictly with the detailed drawing & specification on page no. )

TRIPLE WAVE SLIDE – PGSD 45 (2.1 m) Age Group :- 4 – 12 yrs. Product Area :- 5.5 m x 2.5 m Safe Play Area :- 6.5 m x 3.5 m The amazing triple wave slide is made up of FRP. At a time three children can enjoy sliding. The trapezium platform of the slide is made up of the FRP. The vertical platform support pipes are made up of 80 NB powder coated GI pipes. The railing is made in LLDPE in rotational molding process. The slide entry is made up of 20 NB powder coated GI pipes. The slide entry is mounted on 80 NB and 80 x 20 NB nylon clamp. The ladder frame is made in 20 NB and 25 NB powder coated GI pipes. The triangular steps are made in 16 SWG GI sheets. The work should Comply Strictly with the detailed drawing & specification on page no. )

Supply and fixing of wave slide 5 feet platform height is made up of linear low density polyethylene by rotation process in one piece having shell thickness 4-5 mm with UV stabalised on existing made platform as per direction of engineer in charge

Repairing of Open Gym Equipment (SURFING BOARD,CROSS TRAINER,THAI-CHI SPINNER (2 WHEEL),SEATED PULLER,LEG PRESS,SIT UP BOARD DOUBLE ,CHEST PRESS,POMMEL HORSE,DOUBLE STANDING TWISTER,STANDING SEATING TWISTER,CHEST CUM SHOULDER PRESS,PUSH UP BARS)Including changing bearing , Damage M.S. pipe etc complete in all respect including grease Lubricants under the directions of Engineer-in-charge to fullfil the functional requirement.