SPECIAL REPAIR OF REWIRING OF BLDG NO P 30 MAIL HALL AT 1 CBPO SPL REPAIR OF REWIRING OF BLDG NO N 47 N 65 N 01 AND N 95 COOK HOUSE OF 196 REGT AT DUNDAHERA MILITARY STATION GURGAON SPL REPAIR/ REPLACEMENT OF CEILING AND EXHAUST FANS AGAINST BER AT I

Amount

Surface excavation in soft and loose soil n.exc 30 cm deep and averaging 15 cm deep and getting out, complete all as specified and directed by Engineer-in-charge.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/loose soil, complete all as specified and directed by Engineer-in-charge.

M&L for plain cement concrete type D2 1:4:8 (40mm graded stone aggregate) as in foundation or sub base, complete all as specified and directed by Engineer-in-charge.

M&L for reinforced cement concrete M-25 design mix (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc., basement slabs, under-reamed piles and mass concrete, complete all as specified and directed by Engineer-in-charge.

M&L for reinforced cement concrete M-25 design mix (using 20mm graded stone aggregate) as in columns, pillars, piers, posts and struts, complete all as specified and directed by Engineer-in-charge.

M&L for reinforced cement concrete M-25 design mix using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed by Engineer-in-charge.

M&L for Reinforced Cement cocrete (Nominal mix ), type B-1, (1:2:4) 20mm graded stone aggregate, as in beams, cantilevers, linlles over 1.5m span, complete all as specified and directed by Engineer-in-charge.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter for rough finished surface of concrete, complete all as specified and directed by Engineer-in-charge.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions of square, rectangular or polygonal shape for fair finished surface of concrete, complete all as specified and directed by Engineer-in-charge.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for fair finished surface of concrete, complete all as specified and directed by Engineer-in-charge.

M&L for from work to soffits of suspended slabs such as roof slabs, floor slabs, landing & similar work not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces, complete all as specified and directed.

M&L for mild steel TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and directed by Engineer-in-charge.

All as per item No 12 above but 5mm dia and over upto and including 10mm dia in stirrups, complete all as specified and directed by Engineer-in-charge.

M&L for brick work with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6, complete all as specified and directed by Engineer-in-charge.

M&L for Brick work with sub class "B" bricks , straight or curved on plan of any radius in half brick thick wall, built in CM (1:4), complete all as specified and directed by Engineer-in-charge.

M&L for rendering 15mm thick in CM (1:4) on brick walls or concrete surface finished even and smooth without using extra cement with 2% WPC which shall be paid separately, complete all as specified and directed by Engineer-in-charge.

M&L rendering 15mm thick in CM (1:6) on brick walls or concrete surface finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-charge.

M&L rendering 10mm thick on fair faces of brick work or concrete surface on ceiling in cement mortar (1:3), surface finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surface of wall and applying two coats of cement base paint including scaffolding arrangement, trestles, ladders etc, complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surface of wall and applying two coats of white wash including scaffolding arrangement, trestles, ladders etc, complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash including scaffolding arrangement, trestles, ladders etc, complete all as specified and directed by Engineer-in-charge.

Supply only integral water proofing compound, complete all as specified and directed by Engineer-in-charge.

M&L for hardcore of base n.exc 63mm of broken stone or bolder, deposited, spread and leveled in layers n exc. 15cm thick watered and rammed to a true surface, complete all as specified and directed by Engineer-in-charge.

M&L for 75mm thick cement concrete type C-2, 1:3:6 (20 mm graded aggregate) as in plinth protection, complete all as specified and directed by Engineer-in-charge.

M&L for Moorum/ red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering, complete all as specified and directed by Engineer-in-charge.

M&L for cement concrte 1:4:8 type D2 ,using 40mm graded stone aggregate, of thickness 100mm, complete all as specified and directed by Engineer-in-charge.

M&L for cement concrte type B1 (1:2:4), using 20mm graded stone aggregate, of thickness 35mm, complete all as specified and directed by Engineer-in-charge.

M&L for first quality non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but n exc 0.11 sqm, as in floors laid on 15mm thick cement screed bed in CM (1:6), set and jointed in neat cement slurry at the rate of 3.0 kg per sqm and pointed in white/coloured cement to match the shade of tiles, complete all as specified and directed by Engineer-in-charge.

M&L for Glazed ceramic coloured tiles of 300x200x7mm thick, laid on vertical surfaces such as skirting, dados and risers to steps etc laid over 10mm thick cement plaster in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, complete all as specified and directed by Engineer-in-charge.

S&F Steel window or ventilator , fixed type, with glazing bars, complete all as specified and directed by Engineer-in-charge.

S&F Sheet glass 4mm thick , ordinary quality and glazing with oil puttyor wooden beads in squares n exc 0.5 sq.m in each pan, complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new steel surfaces of any description over 10 cms in width or girth and apply two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed by Engineer-in-charge.

S&F for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, framework of water tanks and similar work con- forming to Fe.290.Gde-E-165, complete all as specified and directed by Engineer-in-charge.

S&F 35 mm thick flsh shutter ,solid core construction, with block board core and ply wood face pannel s, commercial type on both faces, complete all as specified and directed by Engineer-in-charge.

M&L, applying two coats of synthetick enamells paint over a coat of pink primer on wooden surfaces , including preparation of new surfaces of any description , over girth 10 cm width complete all as specified and directed by Engineer-in-charge.

S&F factory made solid PVC door frame of size 50mmx 47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube , suppling and fixing in opening as per specification and drawing, complete all as specified and directed by Engineer-in-charge.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tube for top and bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strips of 20 mm with stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail , lock rail & bottom rail on either side & as gap inserted for top rail & bottom rail , panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement , supplying and fixing in the frame at the site as per specification & drawing, complete all as specified and directed by Engineer-in-charge.

S&F Aluminium anodised barrel tower bolts, 150mm long , of extruded section complete all as specified and directed by Engineer-in-charge.

S&F MS hinges medium weight cold rolled of 100 mm size complete all as specified and directed by Engineer-in-charge.

S&F aluminium handles, 150 mm size, cast type, complete all as specified and directed by Engineer-in-charge.

S&F, aluminium alloy anodised sliding door bolts , of 250mm long with hasp,staple(bolt type) fixing clips of sheet cast or extruded section , fixing bolts and sliding bolts of extruded section complete all as specified and directed by Engineer-in-charge.

S&F vitreous china squatting pan 'Orissa' pattern size 580 x 440mm white with integral foot rest including P or S trap (excluding cistern & flush pipe), complete all as specified and directed by Engineer-in-charge.

M&L for flush pipe of polyethylene of low or high density of PVC 32mm dia for low level cistern including all joint, complete all as specified and directed by Engineer-in-charge.

M&L for PVC valve less, Symphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type and making connections complete, complete all as specified and directed by Engineer-in-charge.

S&F vitreous chinaware wash hand basin (WHB) white size 550mm x 400mm complete including provision of pair of mild steel angle iron brackets of suitable size duly painted, 32 mm dia chromium plated waste coupling, PVC waste pipe and cutting for pinning in ends of brackets in wall etc, complete all as specified and directed by Engineer-in-charge.

S&F PVC connection 15mm dia and 450mm long with washers, complete all as specified and directed by Engineer-in-charge.

S&F 15mm bore Bib tap cast copper alloy fancy typr chromium plated with crutch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed by Engineer-in-charge.

S&F Pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, 15 mm bore of pipe, complete all as specified and directed by Engineer-in-charge.

S&F 15mm bore Angle stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe etc, complete all as specified and directed by Engineer-in-charge.

S&F 15mm dia GI tubing medium grade galvanised with all fittings and fixed to wall/ceiling or laid in floors etc, complete all as specified and directed by Engineer-in-charge.

S&F 20mm dia GI tubing medium grade galvanised with all fittings and fixed to wall/ceiling or laid in floors etc, complete all as specified and directed by Engineer-in-charge.

S&F Rotational moulded polythelene water storage tank three layer of 500 ltrs capacity ( Cyclendrical vertical with closed top) hoisted and fixed in position,all as specified in SSR part-I, complete all as specified and directed by Engineer-in-charge.

S&F Gun metal, globe or gate valves with iron wheel head, screwed both 15 mm bore, complete all as specified and directed by Engineer-in-charge.

S&F Gun metal, globe or gate valves with iron wheel head, screwed both 20 mm bore, complete all as specified and directed by Engineer-in-charge.

S&F Ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for 20 mm dia iron pipe, complete all as specified and directed by Engineer-in-charge.

S&F cast iron floors traps, 75mm outlet dia with CP grating including jointing to waste pipe and fixed in cement concrete type (1:2:4), complete all as specified and directed by Engineer-in-charge.

S&F 75mm bore and cast iron soil waste and vent pipes , in any length with or without ears , with cement joints laid in trenches or in floors, complete all as specified and directed by Engineer-in-charge.

All as per Srl item No 58 above but here-in-before fixed to walls complete all as specified and directed by Engineer-in-charge.

S&F 100mm sand cast iron soil waste and vent pipes, in any length with or without ears , with cement joints laid in trenches or in floors, complete all as specified and directed by Engineer-in-charge.

All as per Srl item No 60 above but here-in-before fixed to walls complete all as specified and directed.

S&F, 100mm bore, CI, branch pieces, single socketed (equal or unequal), ordinary or inverted (spigot or socket type or with parallel branceswith oval access door, complete all as specified and directed by Engineer-in-charge.

All as per Srl item No 62 above but here-in-before 75mm bore, complete all as specified and directed.

M&L for CI Bends (any radius ), diminishing pieces or tapers of 100 mm dia fitted with oval access door, complete all as specified and directed by Engineer-in-charge.

All as per Srl item No 64 above but here-in-before 75mm bore, complete all as specified and directed.

M&L for Chequered cement concrete tiles 20cmx 20cmx 25mm thick with gray cement and pigments , set and jointed and pointed in neat cement slurry in floors, laid over 15mm thick cement screed bed of CM(1:4), complete all as specified and directed by Engineer-in-charge.

S&F 150X150mm size Gully Traps Square or round mouthed Type P etc, complete all as specified and directed by Engineer-in-charge.

S&F CP grating 100mm dia with or without hole, complete all as specified and directed by Engineer-in-charge.

Returning, filling in, inluding spreading, levelling, watering and well ramming excavated soil in layers not exceeding 25cm thick complete all as specified and directed by Engineer-in-charge.

Removing excavated material any type of soil exc 50 m but not exc 250 m deposited where directed at a level n.exc 1.5 m above the starting point for soil, complete all as specified and directed by Engineer-in-charge.

Plain cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in coping and similar work etc. including weathering, slightly rounded or chamferred angles and throating and provision of necessary formwork, complete all as specified and directed by Engineer-in-charge.

Precast reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in cover slab etc. set laid and dry, including provision of necessary formwork, complete all as specified and directed by Engineer-in-charge. Note : (i) Reinfocement shall be measured and paid seperately.

Mild steel of Gde Fe-290 (Gde E-165) as in bend, straps, rungs, handle, holdfast, manhole cover frame and similar small articles, complete all as specified and directed by Engineer-in-charge.

Plain cement concrete (1:4:8) , type D-2, using 40mm grade stone aggregate as in concrete bed to drain pipes laid to falls in trenches in any depth including packing under and haunching against the sides of pipes for 150mm bore pipes with concrete after the pipes are laid and tested, complete all as specified and directed by Engineer-in-charge.

M&L for SGSW drain pipes 150mm dia laid in trenches and jointed in CM (1:3), complete all as specified and directed by Engineer-in-charge.

Plain cement concrete(1:2:4) type B-I using 20mm graded stone aggregate as surface channel/drains inside the manholes and like including weathering, slightly rounded or chamfered angles and throating as directed and provision of necessary formwork to any extent and finished exposed surface even and smooth without using extra cement, complete all as specified and directed by Engineer-in-charge.

Extra over surface channel inside of manholes for forming fair finished drains of channels 30 cm inner girth in cement concrete using extra cement inclding forms, moulds, mitred/stopped ends, complete all as specified and directed. (Inner girth only be measured and paid), complete all as specified and directed by Engineer-in-charge.

Construction of septic tank in ordinary soil, foundation in PCC (1:2:4), for 25 users, brick work in CM 1:4 (with top of slab at ground level) including necessary excavation and earth work in any type of soil and disposal of surplus soil as direced, RCC manholes covers having 6mm plate embedded all around/fibre reinforced cover with angle iron welded frame complete all as per drg No. TD DZ-171, vent shaft with cowl and sludge chambers etc, complete all as specified and directed by Engineer-in-charge.

Construction of sokage well 1:8 mtr dia and 3mtr deep in ordinary soil below inlet (depth) from inlet pipe to ground level 45cm, including excavation and earth work in any type of soil, PCC 45 (1:3:6), type C-2 (using 40 mm graded stone aggregates) in foundation, walling honey combed, cover slab of M-25 design mix, including intercepting chamber, screen chamber in brick work in CM 1:4. RCC cover slab in M-25/RR masonary/ filling with brick bats complete all as per drg No. TD DZ-1124 (R) and directed by Engineer-in-charge.

Taking down carefully the old u/s Aluminium/ Copper point wiring (light, fan, socket or power) complete fitting such as switches, ceiling roses, pendants, sockets, regulators, call bell, holder etc and making good disturbed surfaces of walls including necessary touch up with the adjoining surface of disturbed area ie with OBD/colour wash/white wash as the existing finish complete all as specified and directed by Engr-in-Charge.

M&L for point wiring complete with single core multi strand copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 Volts grade electrical cable in and including existing concealed PVC conduit medium grade and sunk in new pressed steel terminal boxes of required size factory made and factory painted with stove enameled black paint with top cover 3 mm thick plastic/laminated sheet (ISI Marked) of required color with screwed and cup washer with all accessories including 1.5 Sqmm single core with multi strand copper conductor PVC unsheathed cable earth and connected to earth dolly complete all as specified and directed by Engr-in-Charge Note:- New conduit of suitable size with connected fittings will be laid, if there is damage/ blockage in existing conduit and the rates are inclusive of quoted rates and same surface finishes with the adjoining surface of disturbed area with OBD/Colour wash/white wash.

One light / fan point controlled by one No one way switch

One 3 pin 5 Amps socket outlet point controlled by one No one way switch on independent board.

One 3 pin 5 Amps socket outlet point controlled by one No one way switch on same board.

All as per above ser Item No 81 but here-in-before for one socket outlet 5/15 Amps on Independent board with cables 2.5 Sqmm size for phase and neutral and 2.5 Sqmm for earthing complete all as specified and directed by Engr-in-charge.

All as per above Ser Item No. 81 but here-in-before One 3 pin socket outlet, 15 Amps on independent board with cable 4 Sqmm for main current and 4.0 sqmm as earth wire as power point.

S&F switch piano flush type 5/6 Amp complete one way single pole complete all as specified and directed by Engineer-in-charge. Make : GM/Havells/Cona

S&F socket outlet 5 pin 5/6 Amp complete two in one complete all as specified and directed by Engineer-in-charge. Make : GM/Havells/Cona

S&F switch piano flush type 15 Amp complete all as specified and directed by Engineer-in-charge. Make : GM/Havells/Cona

S&F socket outlet 2 in 1, 5 pin 15/5 Amp complete all as specified and directed by Engineer-in-charge. Make : GM/Havells/Cona

S&F ceiling rose surfaces bakelite minimum size 65x50mm with two/ three terminals complete all as specified and directed by Engineer-in-charge. Make : GM/Havells/Cona

S&F Metal clad plug and socket 20 Amps with MCB SP and steel enclosure complete all as specified and directed by Engineer-in-charge. Make : Legrand/Havells/Benlo

S&F of LED of Integrated Batten T5 20 watt - 4 Ft White, indoor decorative PVC extruded T5 LED battern -integrated type complete with including fliexble wire in replacement of old unsv existing 36 Watt tube light fitting complete all as specified and directed by Engineer-in-charge Make:- Cat Part No LTTB4F20LED/W of C&S or equivlent as Havells/Bajaj/Philips/Benlo.

S&F Surface/Recessed mounting 34 Watt (VENUS NEO-857) 2'x2' LED panel fitting, Ultra modern designed architectural LED luminaire which provides soft-light and glare free symmetrical illumination suitable for Armstrong/Grid ceiling in replacement of old unsv existing CFL fitting any type from ceiling of stairs/common areas and making good a disturbed surface/armstrong ceiling to match with armstrong ceiling and getting electrically connected the fitting with switch board for suitable size of PVC copper wire complete all as specified and directed by Engineer-in-charge. Make : Cat Pt No LHEWDRP7PK1W034 of Havells or its equivalent as Bajaj/Philips/Benlo.

S&F Recessed Mounting (Pluto 2x2-857) 34 Watt 2'x2' flat LED panel fitting with soft light and glare free symetrical ilumination suitable for POP ceiling supplied with wedge bracket to fix in existing POP ceiling including cutting/grouting of existing POP ceiling in replacement of existing old unserviceable CFL fitting any type from ceiing of stairs/common areas and making good a disturbed surface/POP ceiling to match with POP and getting electrically connected the fitting with switch board for suitable size of PVC copper wire complete all as specified and directed by Engineer-in-charge. Make : Cat Part No - LHEWEIP7PW1W034 of Havells or its equivalent as Bajaj/Philips/Benlo.

S&F LED in replacement LED Building security light fitting 45 Watt including bracket for fixing of security light fittings of GI pipe light grade of 32/40mm dia with suitable size of clamps, Anchor faster, nut, bolts, and washer and applying two coat of synthetic enamel paint over a coat of red oxide primer GI pipe should be moulded in 45 degree angle at 1mtr height to fix the building security light fitting and neccesary electric connection complete all as specified and directed by Engineer-in-charge. Make :- Cat Part No LTESSE45WLED of C&S or its equivalent as Bajaj/Halonix/Philips/Benlo

S&F ceiling fan regulator, electronic, Socket type complete all as specified and directed by Engineer-in-charge. Make : Cona/GM/Havells

Taking down old unserviceable ceiling fan, dismantling of blades, transportation to work shop and carrying out rewinding, transportation to site, reinstallation and testing complete all as specified and directed by Engineer-in-charge. Note:- Rewinding shall be measured and paid separetely.

M&L for Rewinding of ceiling fan 1200 mm sweep respectively by dismantling of fan motor cutting and removing of burnt windings, cleaning, winding with supper enameled copper wire of superior quality, same gauge of wire, same Nos of turns, provn of insulation paper applying of varnish drying of varnish and assembling of fan including replacement gun metal bush, ball bearing and blades whereever required and applying two caots of synthetic enamel paint first quality by using machine spray including filling cavities with filler complete all as specified and directed by Engineer-in-charge.

Supply and fixing in replacement MCB DB SPN 12 Way with metal double door, (IP43 Protection) flush mounting epoxy powder control having 200 Amps rated bus bar complete all as specified and directed by Engineer-in-charge. Make : Legrand/Siemens/Benlo

M&L in replacement MCB SPN 'C' curve 32/40 Amps 240 Volts, 10 KA complete all as specified and directed by Engineer-in-charge. Make : Legrand/Siemens/Benlo

M&L in replacement MCB SP 06 to 32 Amps 240 Volts complete all as specified and directed by Engineer-in-charge. Make : Legrand/Siemens/Benlo

Taking down unserviceable sub main wiring twin core any size complete and making good the disturbed surface complete all as specified and directed by Engr-in-charge.

M&L for sub main wiring PVC insulated FRLS single core multistranded copper conductor cable 2 Runs of 6 Sqmm for phase and neutral and 1 run of 6 Sqmm for earth wire drawn through existing concealed steel /PVC conduit wiring in wall not less than 25mm dia with all fittings like tees, bends, junction/terminal boxes etc as per site requirement complete all as specified and directed by Engr-in-charge Make:- Havells/Ploycab/Finolex (Note: Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length. New conduit of suitable size with connected fittings will be laid, if there is damage/ blockage in existing conduit and the rates are inclusive of quoted rates and same surface finishes with the adjoining surface of disturbed area with OBD/Colour wash/white wash)

M&L for sub main wiring PVC insulated FRLS single core multistranded copper conductor cable 2 Runs of 10 Sqmm for phase and neutral and 1 run of 10 Sqmm for earth wire drawn through existing concealed steel /PVC conduit wiring in wall not less than 25mm dia with all fittings like tees, bends, junction/terminal boxes etc as per site requirement complete all as specified and directed by Engr-in-charge Make:- Havells/Ploycab/Finolex (Note: Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length. New conduit of suitable size with connected fittings will be laid, if there is damage/ blockage in existing conduit and the rates are inclusive of quoted rates and same surface finishes with the adjoining surface of disturbed area with OBD/Colour wash/white wash)

S&F in replacement of sheet metal enclouser MCCB DB IP 20 double door bus bar neutral link earth bar and din rail VTPN 4 way complete all as specified and directed by Engineer-in-charge. Make:- MDS Legrand Cat No 607752 (DPX 63+12+12) or equivalent in Benlo/Siemens.

S&F in replacement of MCCB 63 Amps 4 pole 415 Volts 16 KA complete all as specified and directed by Engineer-in-charge. Make : Legrand/Siemens/Benlo)

M&L in replacement for Earthing complete with galvanized steel earth plate 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate n.less than 1.5 m below normal ground level, connected to galvanized iron wire 4 mm as earthing lead by means of bolts, nuts, check nuts & washers of galvanized iron or steel besides building at all joints as shown in drgs and including excavation and earth work, GI pipe light grade 25mm bore of protection of GI wire from earth electrode, supply and laying charcoal dust, common salt, PCC (1:2:4) type B-1 Chamber and MS angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type B-1using 20 mm graded stone aggregate Reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia , PGI funnel and wire mesh , 20 mm dia GI Pipe light grade for watering complete all as shown in drg of SSR Part-I (2009) electric plate No. 3 and connected to earth test point including testing complete all as specified and directed by Engineer-in-charge.

M&L in replacement of Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicate dsituation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified and directed by Engineer-in-charge.

M&L for point wiring for one light point controlled by one way switch complete, standard copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable in and including concealed PVC conduit medium grade and sunk in pressed steel terminal boxes of required size factory made and factory painted with stove enameled black paint with top cover 3 mm thick plastic/laminated sheet of required color with screwed and cup washer with all accessories including 1.5 Sqmm standard copper conductor PVC unsheathed cable earth and connected to earth dolly complete all as specified and directed by Engineer-in-Charge for following:- Note:- The rate is inclusive cutting /chasing and of Making good the disturbed surface with cm 1:3 and same surface finishes with the adjoining surface of disturbed area ie with OBD/colour wash/white wash

S&F in replacement sheet metal enclousure MCB DB SPN 8 way double door bus bar neutral link,earth bar and din rail complete all as specified and directed by Engineer-in-charge.

S&F RUGBY Bulkhead suitable for LED 09 Watt of Base B22, Bulk head in die cast aluminium housing & frosted glass including all accessories connecting up twisted flexible copper conductor cable of suitable size of 230 V, 50 Hz complete. Cat : LHKL01160099 of Havells or equivlent make in C&S/Halonix/CG/Phillips

S&F in replacement of MCCB 63 Amps 3 pole 415 Volts 25 KA complete all as specified and directed by Engineer-in-charge.

S&F LED Integrated Batten T5 LED tube light fitting of 10 Watt - 2' white, indoor decorative aluminium extruded T5 LED battern integrated type complete with including fliexble wire in replacement of old unsv existing 36 Watt tube light fitting complete all as specified and directed by Engineer-in-charge. Make:- Havells/Philips/CG/C&S/Bajaj

S&F in replacement RUGBY Bulkhead suitable for LED 09 Watt of Base B22, Bulk head in die cast aluminium housing & frosted glass including all accessories connecting up twisted flexible copper conductor cable of suitable size of 230 V, 50 Hz complete all as specified and directed by Engineer-in-charge. Make:- Havells Cat Part No : LHKL01160099 or its equivlent as C&S/Halonix/CG/Phillips.

S&F for Batten holder with PVC body and back plate suitable for LED Bulb B-22 cap complete all as specified and directed by Engineer-in-charge. Make : Cona/Kinjal/Havells

S&F in replacement LED RETROFIT Lamp of 9 watt for fixing in batten holder/wall mounting/bulkhead point complete all as specified and directed by Engineer-in-charge. Make C&S\Havells\Halonix/Philips

S&F LED RETROFIT Lamp of 9 watt for fixing in batten holder/bulkhead point complete all as specifed and directed by Engr-in-Charge Make:- C&S\Havells\Halonix/Philips

Taking down of old serviceable/unserviceable exhaust fan dismantling of blades, transportation to work shop and carrying out rewinding, transportation to site, reinstallation and testing complete all as specified and directed by Engineer-in-charge. Note : Rewinding will be measured and paid under respective item of this Schedule.

M&L for Rewinding of Exhaust fan 300/450 mm sweep by dismantling of exhaust fan motor cutting and removing of burnt windings, cleaning, winding with super enamelled copper wire of superior quality, same gauge of wire, same Nos of turns including provision of insulation paper applying of varnish drying of varnish and assembling of exhaust fan complete all as specified and directed by Engineer-in-charge.

Supply and laying in replacement of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sqmm x 4 core complete all as specified and directed by Engineer-in-charge.

Supply and laying in replacement of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sqmm x 2 core complete all as specified and directed by Engineer-in-charge.

Supply and laying GI light grade pipe in replacement of size 40mm bore laid in Road, Culvert, Path and Floor for protection to LT U/G cable and making good to the disturbed surface including PCC works complete all as specified and directed by Engineer-in-charge.

Excavation in trenches in any type of soil n exc 1.5 mtr in width and n. exc 1.5 mtr in depth and getting out all as required for laying of cables,Foundation filling of poles or stays complete all as specified and directed by Engineer-in-charge.

M&L for sand cushioning to under ground cables 8 cm thick before laying the cable and 15 cm, thick after laying, stretching and testing the cable complete all as specified and directed by Engineer-in-charge. Note:- Punned thickness 18 cm shall be measured and paid.

Supply and laying sub class ‘B’ bricks well burnt for cable protections laid flat with length equal to width of brick over cable perpendicular to length of cable complete all as specified and directed by Engineer-in-charge.

Supply & fixing in replacement of ceiling fan 1200 mm sweep, 300RPM, with air delivery 255/265 cum/min (Opal white) economy range high speed having full copper motor & ribbed aluminium blades for higher air and powder coating including making arrangement to hanging of fan to ceiling with proper hook, nuts, bolts etc and connecting up with twin core twisted fleaxible copper conductor cable with suitable size complete all as specified and directed by Engineer-in-charge Make:- Cat part No. ES-50 of Havells, Cat part No. 5116877-3504705768 of Bajaj, Cat part No. 5116877-37504518748 of Orient Note:- Old ceiling fan to be deposited in MES store of AGE E/M.

Supply and fixing in replacement of metal body exhaust fan 300 mm sweep, 230 Volts with louvers complete and copper wound (Heavy duty-1400 RPM) including necessary electric connection with appropriate size of PVC copper wire from ceiling rose/switch board to exhaust fan including fixing of nut-bolts of suitable size and making good the disturbed surface of wall with OBD/White wash to match with existing complete all as specified and directed by Engineer-in-charge. Make:- Cat Part No : Turbo Force SP of Havells or its equivalent as Cromption Greaves/ Bajaj Note:- Old exhaust fan to be deposited in MES store of AGE E/M.

Supply and fixing in replacement of metal body exhaust fan 450 mm sweep, 230 Volts with louvers complete and copper wound (Heavy duty-1400 RPM) including necessary electric connection with appropriate size of PVC copper wire from ceiling rose/switch board to exhaust fan including fixing of nut-bolts of suitable size and making good the disturbed surface of wall with OBD/White wash to match with existing complete all as specified and directed by Engineer-in-charge. Make: Cat Part No - Turbo Force SP of Havells/ Krypton (HDEF) of Halonix or its equivalent as Bajaj. Note:- Old exhaust fan to be deposited in MES store of AGE E/M.

S&F MCB DB single pole and neutral 6 way single door type (IP 43 protection) sheet steel, powder coated DB's suitable for MCB's fitted with bus bar,neutral link,earth bar and Din Rail including connecting cable to the SPN/MCBs using the dolly and the wires in the DB which should be properly tied accord complete all as specified and directed by Engineer-in-charge. Make:- CAT part No. EXDBSD06 of HPL or its equivalent as Legrand/Crabtree/ABB

M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground certically to a depth not less than 3.0mtr deep below GL with top edge of the plate not less than 2.5 mtr below normal GL and connected to earth plate. Earth plate surrounded by 15 cm thick packed layers of charcoal dust and common salt upto 1.5 meter depth all earth lead of GI earth wire 4mm by means of bolts, nuts check nuts and washers of galvanized iron or steel pipe light grade 15 mm bore and water pipe 20mm bore GI medium grade with funnel and wire mesh, including all necessary excavation and earth work PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover and all as shown in electrical plate No. 3 of MES schedule Part-I of 2009 and also including making test point for testing of earthing made out of gun metal or phosphorous bronge size 75x75x25 mm complete all as specified and directed by Engineer-in-Charge. Note:- 1. RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM weighting not less than 4KG/Sqmm in lieu of CI cover. 2. Charcoal dust and common salt upto 1.5 meter depth shall be filled in layers of 15 centimeters all around the earth plate on testing after completion of earthing if desired earth resistance is not achieved, the earthing will be redone at no extra cost to obtain the desired earth values.

S&F MCB SPN 32/40 Amp 240 volts C Curve complete all as specified and directed by Engineer-in-Charge.

S&F MCB SP 6 to 32 Amp 240 volts C Curve complete all as specified and directed by Engineer-in-Charge.

Supply and Laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sqmm x 2 core complete all as specified and directed by Engineer-in-Charge.

Supply and laying GI tubing medium grade with all fittings laid in trench or on walls of 40mm bore complete all as specified and directed by Engineer-in-charge.

Supply and Laying GI tubing medium grade with all fittings laid in trench or on walls of 20mm bore complete all as specified and directed by Engineer-in-charge.

Supply and fixing Gate/Globe valve conforming to IS 9338, 40mm bore (1.5”) complete all as specified and directed by Engineer-in-charge.

Supply and fix gate/globe valve conforming to IS 9338, 20mm bore complete all as specified and directed by Engineer-in-charge.

M&L for Cutting existing GI pipe of size 80 mm bore for taking new connection including all fittings, joints etc complete all as specified and directed by Engineer-in-charge.

M&L for Valve pit of size (90 x 90 x 100 cm) consisting of randem rubble uncorsed stone masinary in cement motor 1:6 50 mm thick coping with PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) incl excavation and earth work and disposal of surplus soil to a distance not exc 50 mtr and depositing where all as directed by Engr-in-Charge, plastering internally with 15 mm thick in cement motor 1:6 and flush pointing externally in the same motor as work proceeeds and mild steel sheet cover (3.15 mm thick) angle iron frame of 40 x 40 x 6 mm handel locking arrengement and painting with two coats of synthetic enamel paint over a coat of red oxide primer on steel surface complete all as specified and directed by Engineer-in-charge.

Note:- The contract sum shall be after deducting the amount of Credit shown in Credit Schedule of this Tender.

aggarwal engineers contractors

M/S.Parmod Johar