PROVN OF DRAIN COVER AND ADDN ALTN TO DRAINAGE RETAINING WALL AND MISC INFRA AT NSOI AND PROVN OF ONE STORE ROOM AT ASCON NODE UNDER GE SOUTH UDHAMPUR

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard /dense soil complete all as specified and as directed.

Excavating in trenches, n.exc 1.5 m wide and n.exc 1.5 m in depth; for foundation, & n exc 10 Sqm on plan and n exc 1.5 m in depth and getting out in any type of soil, complete all as specified and as directed.

Returning, filling incl spreading leveling watering and well ramming in layers not exceeding 25cm in any type of soil complete all as specified and as directed.

Removing excavated material (soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Taking down cement plaster on brick or stone masonry wall etc incl racking out joints haking for key, scrubbing down with water etc as in external surfaces of man holes, septic tank, filter bed etc incl removing of debries complete all as specified and as directed.

Demolition of cement concrete reinforced (reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

Demolition, Cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of Bricks or stone masonry built in cement mortar complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) in foundations, filling and mass concrete, complete all as specified and as directed.

M&L for plain cement concrete1:2:4 type B-2 using 40 mm graded stone aggregate as in channels and drains, foundation and similar work etc complete all as specified and as directed.

M&L PCC 1:2:4 type B0 (12.5mm graded aggregate) as in coping, benching and similar work etc including necessary form work complete all as specified and directed.

M&L 75 mm thick cement concrete (1:4:8) type D2 as sub base to floor complete all as specified and as directed.

Reinforced cement concrete M-25 (20mm graded aggregates) design mix as in foundations, including rafts, footings, foundation, beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Reinforced cement concrete M-25 (20mm graded aggregates) design mix columns, pillars, piers,posts and struts complete all as specified and directed.

Reinforced cement concrete M-25 (20mm graded aggregates) design mix as in beams, cantilevers,bressummers, lintels over 1.5m span all as specified and directed.

Reinforced cement concrete M-25 (20mm graded aggregates) design mix as in slabs supported on walls, beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and directed.

Reinforced cement concrete M-25 (20mm graded aggregates) design mix as in chajjas complete all as directed

M&L for providing cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregates for filling in the pressed steel door frame/hold fast complete all as specified and as directed.

M&L for 75 mm thick plain cement concrete type D-2 (1:4:8) (40 mm graded stone aggregates) as in sub base complete all as specified and directed.

M&L for Precast cement concrete louvers and jallies 25mm thick set in cement mortar 1:4 type B0 (1:2:4 using 12.5mm graded aggregate etc sample as approved by GE incl takong out old precast jali complete all as specified and directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and as directed.

M&L for Brick work with sub-class 'B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for walling of random rubble masonary, Squre, recangular uncoursed, well bonded, bedded and solidly hearted, built in CM (1:6) complete all as specified and as directed.

All as per srl item No here in before but except stone masonry complete all as specified and as directed.

M&L for raised pointing to random or polygonal rubble masonary coursed or un coursed in CM (1:3) complete all as specified and as directed.

M&L for extra over hammer dressed facings, with maximum depression on face from straight edge held against the dressed surface n. exc 20 mm; to block-in-course masonry complete all as specified and as directed.

M&L for hardcore of broken stone of guage n.exc 63mm deposited spread and levelled in layer n.exc 15cm thick watered and well rammed to true surfaces complete all as specified and as directed.

M&L for TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

All as per item No 28 above but 5mm dia and over including 10mm dia in stirrups, spaces and binders etc all all as specified and as directed.

M&L for Machine cut kota stone slab flooring 20-25 mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete including 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

M&L for machine cut kota stone 20-25 mm thick in skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for sand cushion 20 to 30 mm thick for laying and fixing interlocking tiles complete all as specified and as directed.

M&L machine pressed precast concrete interlocking paver block (glossy finish) any shape and size (sample approved by GE) confirming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment complete all as specified and directed.

M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete, of frame size 105 x 60 mm complete all as specified and as directed.

M&L for chequered cement concrete (glossy finish) tile 300 mm x 300 mm x 25 mm thick set jointed and pointed in neat cement slurry in floor with grey cement and pigment including 15mm thick in CM 1:6 complete all as specified and directed.

M&L for heavy duty coloured (Dura stone) tiles n exc 0.36 Sqm of 10-15mm thick tiles as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including including 15mm thick in CM 1:6 complete complete all as specified and directed.

M&L for glazed ceramic wall cladding coloured tiles 300x600x7-10mm thick (design and size as approved by Engr in Charge) as in vertical surfaces of walls, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm cement rendering in cement mortar 1:4 or fixing with chemical of Dr Fixit or as directed complete all as specified and as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

M & L 18-20 mm thick granite (of any type) work( table rubbed and polished) in steps, jambs, pillars, window sills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab complete all as specified and as directed.

M&L for 10mm thick on fair faces of brick /concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 15mm thick rendering on fair faces of brick/concrete or stone surfaces or drain in cement mortar 1:4 and finished even and smooth without using extra cement complete with water proofing compound complete all as specified and as directed. (WPC shall be measured separtely).

Supply only Liquid water proofing compound complete all as specified and as directed.

M&L for 5mm thick CM 1:4 rendering on fair surfaces of ceiling work and finished even and smooth without using extra cement all as specified and as directed.

M&L for applying 3mm thick layer of wall putty on walls complete all as specified and as directed.

Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter for rough flat finished surfaces of concrete,complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough flat finished surface of concrete, complete all as specified and as directed.

Formwork to flat sides and soffits of or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, complete all as specified and as directed.

Formwork to soffits of suspended flat slabs such as roof slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

Formwork to edges of concrete flats, treads breaks in floors, window cills, concrete railings,openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in wall, horizontal or sloping and similar work exc 10cm but n exc 20cm wide.

Formwork to chullah hoods, chajjas,troughs and similar items including edges for rough flat finished surface of concrete, complete all as specifed and directed.

M&L two coats of oil bound distemper on walls including preparation on new surfaces over a coat of primer complete all as specified and directed.

M&L for preparation of new plastered surfaces on ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surfaces on walls and applying two coats of cement based paint complete all as specified and as directed.

S&F factory made, 2nd class hard wood (sal/hollock), plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides, the side of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, 35 mm thick complete including fixing only iron mongery such as tower bolt,handle,hinges,aldrop bolt etc complete all as specified and as directed.

S&F steel window (box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

Description all as per item as above here in before but without glazing bar complete all as specified. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 ii) MS fillets, glazing, wire gauge shall be measured and paid separately

M&L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 quality A incl one shop coat of zinc chromate primer paint incl preparation of surfaces at contractor's workshop before fabrication complete all as specified and as directed.

S&F factory made SFRC (Steel Fibre Reinforced Cement Concrete) drain cover of 600x400x75mm thick including frames or size and design as approved by Engr in Charge of strength & durability, crack resistance, heavy load capacity, corrosion resistance and reduced noise polution complete all as specified and as directed. (Design and size shall be approved by Engr in Charge before commencement of the work). Make : Kashmir Spun Pipe & Allied Industries, Shivalik Concrete Pipes, Paves India Company or its equivalent firms.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls bore of the pipe 110 mm complete all as specified and as directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and as directed.

S&F stainless steel wire cloth 0.36mm nominal and average width of apreture 1.40mm and fixed with tinned teaks or wire staple complete all as specified and as directed.

M&L for preparation of newly steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

M & L for applying two coats of synthetic enamel ordinary tint paint including red oxide primer and preparation extra complete on new steel or iron surfaces of any description, over 10cm in width or grith, not otherwise described complete all as specified.

M&L for preparation of wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primercomplete all as specified and as directed.

S&F mild steel sliding door bolt plate type 250 mm long stove enamelled black with bright bolt not less 12 mm dia bolt with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, complete all as specified and as directed.

S&F aluminum handles cast type, anodised, 150 mm size complete all as specified and as directed.

S&F aluminium anodised barrel tower bolts of extruded section with 150 mm long bolt complete all as specified and as directed.

S&F mild steel cold rolled butt hinges medium weight 100 mm long complete all as specified and as directed.

S&F in repair curtain/Harrison rails of stainless steel 25mm dia with brackets, stops, end bulbs, rollers etc complete all as specified and directed.

M&L for 10 mm thick rendering in CM 1:3 on roof sufaces, finished even and smooth without using extra cement all as specified and as directed. Note :- Supply only water proofing compound shall be measured and paid seperately under the respective item.

M&L for Applying bituminous primer on roof surfaces @ 0.40 liters/Sqm and applying one coat of semi hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and thereafter supply and laying 3mm thick polymeric water proofing membrane, five layered, of weight not less than 3 Kg per Sqm with centre layer core of 90 micron high molecular density polyethylene film and bonded completely to the surface with overlap of 10 cms (overlaps to be thermo fused by flame) followed by another coat of semi hot blown bitumen 85/25 grade bitumen @ 0.70 Kg/Sqm and provide aluminium paint as per manufacturing instruction complete all as specified and as directed. Make: STP/IWL Note:- Water proofing treatment will be done by IWL or through a specialized agency.

M&L for 75mm thick cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in plinth protection laid in alternate bays (n exc 2 sqm each) area with 6mm wide joints and 10mm wide joints between the walls and plinth protection, finished even and smooth without using extra cement, outward slope of not less than 1:12, the joints shall be filled with mastic filling comprising one coat of bitumen 85/25 grade and three parts of sand by weight, complete all as specified and as directed.

Point wiring for one light/ fan/bell point controlled by one switch using 1.5 Sq mm FRLSH copper conductor cables (multistranded) PVC insulated and unsheathed in and including PVC concealed conduit pipe as per site requirement (size not less than 20mm dia), medium grade with Modular sunken boxes & PVC/metal back plate for mounting modular type switches, sockets & regulators etc with cover plate modular type including supplying and laying PVC insulated and stranded unsheathed 1100 volts coppper conductor cable 1.5 Sq mm as earth wire connected to earth dolly including cutting of chases in wall /ceiling etc and making good the disturbed surfaces match to existing with cement mortar and putty white /colour wash complete all as directed. Make: Havells/ Finolex/ Polycab.

All as per srl item No 79 but for 3/5 pin 6 Amps socket outlet independent board including PVC insulated PVC unsheathed 2.5 sq mm earth wire and connected to earth dolly.

All as per Srl item No 79 but for 3/5 Pin 16 Amps socket outlet independent board with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 2.5 sq mm earth wire standard and connected to earth dolly.

S&F for modular switch 6 Amps single pole one way 230 V, 50 Hz, AC , with outer cover complete all as specified and directed by Engr In charge. Make:Legrand/Havell crabtree/L &T

S&F for modular switch 16 Amps single pole one way 230 V, 50 Hz, AC , with outer cover complete all as specified and directed by Engr In charge. Make:Legrand/Havell crabtree/L &T

S&F for modular socket 3 Pin 6 Amps flush type 230 V, 50 Hz, AC , with outer/inner cover complete all as specified and directed by Engr In charge. Make:Legrand/Havell crabtree/L &T

S&F for modular socket combined 2-in-1, 6 Pin 6 & 16 Amps 230 V, 50 Hz, AC , flush type with outer/inner cover complete all as specified and directed by Engr-In-Charge. Make:Legrand/Havell crabtree/L &T

M &L Ceiling rose, surface bakelite 65x 50mm three terminals fixed on PVC Round Block complete all as specified and directed by Engr In charge.

S&F electronic step type fan regulator 100 watt 230 volts 50Hz two module C/S deluxe type complete all as specified and directed. Make- Havells/ Legrand/ Philips

S&F Sheet metal enclosure double door type for DBs (when MCB to be used) 4 way 240 volts with Suitable rated busbar and neutral link including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Make: Schneider/ Legrand/L&T

S & F MCB Single pole and neutral 240 volt any rating from 40 amps 'C' series,with rupturing capacity 10 KA, inculding providing thimble for out going cable complete all as specified and directed. Make: Schneider/ Legrand/L&T

S & F of MCB single pole 240 volt any rating from 10 to 40 amps 'C' series, with rupturing capacity 10 KA,inculding providing thimble for out going cable complete all as Directed & Specified. Make: Schneider/ Legrand/L&T

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) including hanging arrangement all as specified and directed by Engr-In-Charge. Make-Usha Techno Air /Khaitan Magma/Bajaj Energos

Supply and fixing LED lights fitting 1x 20W,230V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make- Syska/Philips/Havells/Bajaj

Supply, laying and testing cable with cable gland, XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) of size 6 sqmm x 4 core 1100 Volts grade with stranded aluminium conductor all as specified and directed by Engr-In-Charge.

Supply and fixing LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp,clamps,suitable bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.Make- Syska/Philips/Havells/Bajaj

paras ram pachiala (BID ID -3384199)

RAMAN CONSTRUCTION CO (BID ID -3384559)

vijay constrction co (BID ID -3384807)

anil construction co. (BID ID -3384291)

VIRINDER SINGH (BID ID -3384366)

M/S ASHOK KUMAR PACHIALA (BID ID -3384754)

M/S Ashok Kumar Jaswal (BID ID -3383784)

M/S SHUBAM ENGINEERS (BID ID -3385228)

M/S IMRAN MAJID (BID ID -3381925)

M/S SHREE RAM DUBEY AND SONS (BID ID -3385213)

PARDEEP SHARMA (BID ID -3384188)