WELCOME MAINTENANCE TO BUILDINGS AND CERTAIN PETTY REPAIR WORK IN ZONE B RESIDENTIAL AREA AND REPAIR TO INTERLOCKING TILES, CHEQUERED TILES AND MISC WORK IN COMMON AREA OF KWC AREA UNDER GE I RND DELHI

Amount

Taking down cement plaster on brick walls or concrete surfaces, raking out joints hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 10mm thick plaster on brick/concrete surface in CM 1:4 surface finished even and smooth without using extra cement mixed with liquid WPC complete all as specified and directed. Note :- Water proofing compound shall be measured and paid separately

M&L for rendering 15mm thick in CM 1:4 on other than fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement ,mixing with liquid WPC complete all as specified and directed. Note :- Water proofing compound shall be measured and paid separately

M&L rendering 15mm thick plaster in CM 1:6 on brick walls or concrete surface, surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick plaster on concrete surfaces as in ceiling, Chajja etc in CM 1:3 finished even and smooth without using extra cement complete all as specified and directed. Note for Ser No 1 to 5 :- The rates are inclusive of necessary scaffolding upto a height of G+7 storey.

Supply only liquid water proofing compound complete all as specified and directed. Make :- PIDIPROOF LW+ of Dr FIXIT or equivalent as approved by GE.

M&L for preparation of newly plastered surface of walls and applying two coats of oil emulsion distemper over and including 2mm thick wall care putty in two layers (each layer minimum 1mm thick) complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper (white or tinted) over a coat of alkali resistant primer complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls including all cornices, pilasters etc and applying two coats of acrylic exterior emulsion apex paint (weather proof) of approved tint / shade(s) over and including one coat of water based alkali resistant primer complete all as specified and directed.

M&L preparation of newly plastered surfaces of ceiling and applying two coat of oil bound distemper(white or tinted) over a coat of alkali resistant primer, complete all as specified and directed.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint with roller/spray having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including water based priming coat of exterior primer applied @ 0.90 litre/ 10sqm over surface complete all as specified and directed. Note:- (i) The application will be done by the specialist agency. MOU will be submitted by the contractor with the OEM. (ii) Rate also includes necessary scaffolding to carry out work upto a hight G+7 floor.

M&L preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls including brooming down or steel wire brushing scraping down smoke soot, moulds, moss and efforescent salts and trading oil and greasy spots and applying one coat of white wash complete all as specified and directed.

All as per item Ser No 13.00 above but on ceiling for one coats.

M&L for preparation of old decorated surfaces including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efforescent salts and trading oil and greasy spots filling minor holes with putty and applying one coat of oil bound distemper complete all as specified and directed

All as per item Ser No 15.00 above but two coats of oil bound distemper.

All as per item Ser No 15.00 above but on ceiling surface.

All as per item Ser No 15.00 above but one coat of plastic emulsion paint.

M&L for complete removal of the existing treatment on walls and applying two coats of oil emulsion distemper over and including 2mm thick wall care putty in two layers (each layer minimum 1mm thick) complete all as specified and directed

M&L for applying one coat of synthetic enamel paint over old painted wooden surfaces of any description over 10cm width or girth including preparation of old surfaces complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint over old painted steel surfaces of any descripition over 10cm width or girth including preparation of old surfaces complete all as specified and directed.

M&L for applying two coats of French polishing on old surfaces of any description, width or girth including preparation of surfaces complete all as specified and directed.

M&L for preparation of old painted concrete/brick/plastered surface of any description not otherwise described over 10cm width and girth and applying one coat of synthetic enamel paint (ordinary tint) complete all as specified and directed.

M&L in repair for preparation of surface for application of water based epoxy resin coating of waterproofing for internal wall dampness and filling of cracks over CM 1:4 and making the surface smooth and finish complete all as specified and directed. Note :- (a) Complete removal of treatment/plaster(where needed) on internal walls and preparation of surface after rendering with CM 1:4 for application and making the surface wet . (b) Apply first coat of Dr. fixit Dampguard in ratio (1U base:1U hardner:1U water) in one direction and leaving the coat to dry for 6 to 8 hrs. (c) Apply second coat of Dr. fixit dampguard in ratio (1U base:1U hardner:1U water) in perpendicular direction to the first coat applied and leaving the surface to dry for 24 hrs. Material: Dr. fixit Dampguard or equivalent.

Removal of air lock/blockage of water in GI tubing 15mm/20mm bore cleaning the pipe or fitting etc and refixing the same in position complete all as specified and directed.

Repair to leakage in bib taps,pillar taps,stop cock, angle valve and low level flushing cistern,etc of any description by changing the spindle, washer etc complete all as specified and directed.

Easing door,window shutters of any size/any number of panels for easy closing/opening, tightening of hinges or changing the position of hinges adjustments of tower bolts, sliding bolts etc complete all as specified and directed.

Supply and fix in repair brass spindles for bib tap and angle cock etc (as per sample kept in office) complete all as specified and directed.

Supply and fix in repair Brass spindle for WHB mixer/Wall Mixer and concealed stop cock (as per sample kept in office) complete all as specified and directed.

S&F in repairs of 32mm/39mm dia PVC waste pipe fixed to WHB, sink, Urinal etc complete all as specified and directed.

S&F in repair small fittings galvanised iron medium grade such as sockets, elbow, nipple,tee,union and hexa nipple etc as requiered for GI tubing for 15mm bore pipe complete all as specified and directed.

All as per Item Ser No 31.00 above but for 20mm bore pipe.

S&F in repair PVC over head water tank cover for tank capacity 500, 750 & 1000 litre with fixing bracket and screw complete all as specified and directed. Make :- Sintex/Polycon/Sheetal

S&F in repair PVC over head water tank cover for tank capacity 2000 litre with fixing bracket and screw complete all as specified and directed. Make :- Sintex/Polycon/Sheetal

S&F in repair brass chromium plated jet spray with 1m long chromium plated tube for single syphonic EWC complete all as specified and directed.

S&F in repair flush pipe of 32mm dia PVC for low level flushing cistern including jointing to WC complete all as specified and directed.

S&F in repair health faucet brass chromium plated (hand jet) 15mm bore with 1mtr tube and fitting complete all as specified and directed. Make:Prayag/Parryware/Marc

S&F in repair fancy type brass chromium plated two way bib cock of 15mm bore screwed for iron pipe or brass ferrule etc complete all as specified and directed.

S&F in repair angle valve 15mm dia cast copper alloy chromium plated fancy type with capstan head screwed both ends for iron pipe or for union complete all as specified and directed.

S&F in repairs Bib tap 15mm dia brass chromium plated fancy type with capstan head screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair fancy type pillar tap 15mm dia cast copper alloy with capstan heads chromium plated screwed down high pressure with or with out lettered Hot or cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed.

S&F in repair brass CP WHB mixer for mixing hot & cold water screwed down for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair 15mm bore brass chromium plated continental non telephonic wall mixer shower hot & cold, bright finish with three joints screwed the ends for iron pipe and plugging complete all as specified and directed.

S&F in repair waste fitting brass CP 40mm dia for sink,basin complete all as specified and directed.

S&F in repair in ball valve high pressure of PTMT complete with aluminum rod and polyplast ball for 15mm dia iron pipe complete all as specified and directed.

All as per Item Ser No 45.00 above but 20mm bore.

S&F in repair 20mm gun metal, globe or gate valves wih iron wheel head,screwed both ends for iron pipe complete all as specified and directed.

All as per item Ser No 47.00 above but 25mm dia.

All as per item Ser No 47.00 above but 40mm dia.

Disconnecting existing tanks, setting aside (or lowering if equired ) for repairs ,cleaning,etc.and hoisting if required reconnecting and refixing in position. including cleaning and removing all scales and dirt from tanks and from mouths of circulating pipe etc for 250 ltr to 500 ltrs capacity of tanks complete all as specified and directed.

All as per item Ser No 50.00 above but capacity of tank exc.500 ltrs but n.exc.1000 ltrs

All as per item Ser No 50.00 above but capacity of tank exc.1000 ltrs but n.exc.2000 ltrs

S&F in repair 15 mm dia GI steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

All as per item Ser No 53.00 above but 20mm dia.

S&F in repair 20mm outer dia 3-layer PP-R P o l y p r o p y l e n e random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polyproplylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

All as per item Ser No 55.00 above but 25mm outer dia.

M&L for Making connection of PP-R distribution branch with PP-R main of sizes 16 to 40mm outer dia of pipe by providing and fixing tee including cutting and making fusion joint etc complete all as specified and directed.

S&F in repair PPR gate valve of outer dia 25mm (brass insert) as per requirement of the site complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in CM(1:3) to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth in brick walls complete all as specified and directed.

S&F in repair PVC valve less 10ltrs capacity syphonic action type flushing cistern low level white with inlet ball valve float and handle push type including flush pipe 32mm dia and connection to WC etc complete all as specified and directed.

S&F in repair vitreous china squatting Pan “Orissa” Pattern, of size 580mm x 440mm white with integral foot rests (excluding flushing cistern and flush pipe) including provision of cement concrete bedding complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white colour (excluding fixing bolts, flushing cistern & flush pipe) including Plastic water closet seat, white, closed pattern with flat bottom, & cover & mild steel CP or aluminised hinging device complete all as specified and directed.

S&F in repair vitreous china wash hand basin, white colour of size 550x400mm (flat back, or angle back type) including cutting for and pinning in ends of brackets or erecting stand inclusive of waste pipe,waste coupling etc complete all as specified and directed.

M&L in repair 75mm dia cast iron floor trap with grating including jointing to waste pipe etc fixed in PCC 1:2:4 type B-1 complete all as specified and directed.

S&F in repair sand cast iron `P' or `S' trap 100mm dia complete all as specified and directed.

S&F in repair stainless steel toilet paper holder box type fixed to wall with CP brass screw complete all as specified and directed.

S&F in repair plastic water closet seat white closed pattern with flat bottom cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S&F in repair brass CP grating 125 mm dia with or without hole for waste pipe fixed on floor / nahani trap fixed with cement mortar complete all as specified and directed.

S&F in repair Stainless steel sink, 1.00mm thick for kitchen or laboratory with plug waste pipe, washers including cantilever cast iron brackets connecting union etc. overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair Stainless steel sink with drainge board, 1.00mm thick for kitchen or laboratory with plug waste pipe, washers including cantilever cast iron brackets connecting union etc. overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F 110mm dia PVC SWR pipes single socketed in any length with rubber joint fixed with to wall upto a height of G+7 floors including necessary scaffolding if required and taking out old unserviceable PVC pipe complete all as specified and directed.

S&F in repair PVC (SWR) 110mm dia bends complete all as specified and directed.

S&F in repair PVC (SWR) 110mm dia bends with oval access door complete all as specified and directed.

S&F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls upto a height of G+7 floors including necessary scaffolding if required and taking out old unserviceable PVC pipe complete all as specified and directed.

S&F in repair PVC (SWR) 75mm dia bends complete all as specified and directed.

S&F in repairs PVC (SWR) 75mm dia bends with oval access door complete all as specified and directed.

S&F in repairs PVC connections 15mm dia & 600mm long with PTMT nuts complete all as specified and directed.

S&F in repairs brass chromium plated shower rose 125mm dia with swivel joint complete all as specified and directed.

S&F in repair kitchen plate rack of size 33" X 31" X 10" made out of 1mm thick stainless steel sheet complete all as specified and directed.

M&L for filling white cement in traps/sides of 'P' or 'S' trap/joint of flush pipes and WC and making good complete all as specified and directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) n.exc 1.5sqm and making good to disturbed surface complete all as specified and directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame)exc 1.5sqm but n.exc 4 Sqm and making good to disturbed surface complete all as specified and directed.

Taking down shutters exceeding 1.00 sqm but n.exc 2.00 Sqm each complete all as specified and directed.

M&L for 2nd class hard wood plain solid straight chowkhats and frames wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

S&F pressed steel frames for doors with one or more rebates of size 125x60 mm including necessary fixing lugs, lock strike plate etc complete made out of 1.25 mm thick MS sheet complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 (12.5mm graded stone aggregate) for filling of Pressed steel frame etc, rounded or chamfered on edges complete all as specified and directed.

S&F 35mm thick flush shutter solid core construction with block board core and ply wood face panels commercial type on both sides complete all as specified and directed.

S&F 35mm thick factory made, 2nd class hard wood plain framed, panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS-1003 (Part I) complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skelton door shutter open rebated and prepare to receive glass, gauge etc (without sash bars) edges of framing palin, chamfered rounded fitted with cut and mitred beads for securing glass etc sizes of member as spd in SSR Part I sec 8 clause 8.20 (a) complete all as specified and directed.

M&L for preparation of new wooden surfaces over 10cm width and girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F factory made solid PVC door frame size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube as per spacification and drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm the style consisting of frame made out of MS tube, for top & bottom rail, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, bottom rail & lock rail on either side & as gap insert for top rail and bottom rail. panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement as per specification and drawing complete all as specified and directed.

S&F stainless steel butt hinges 100 mm long complete all as specified and directed.

S&F 100 MM butt hinges,etruded alum alloy with galvanised mild steel hinge pin, anodised and fixed,type B-21 complete all as specified and directed.

S&F 150 mm long aluminum anodized barrel tower bolt of extruded section complete all as specified and directed.

S&F 250mm long aluminum alloy anodized sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy complete all as specified and directed.

S&F 150mm size aluminum handles cast type, anodized complete all as specified and directed.

S&F stainless steel wire mesh of size 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repairs stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple etc in wooden/steel frames complete all as specified and directed.

S&F in repair 4 mm thick sheet glass in squares/rectangle not exc 0.50 sqm in each pane fixed with wooden beads or putty (in metal/wooden frames etc) upto a height of G+7 including necessary steel/wooden scaffolding etc complete all as specified and directed.

All as per item Ser No 101.00 above but exc. 0.50 Sqm in each pane

S&F in repair 100 mm long aluminum anodized barrel tower bolt of extruded section complete all as specified and directed.

S&F in repair 200 mm long aluminum anodized barrel tower bolt of extruded section complete all as specified and directed.

S&F in repair 250mm long aluminum alloy anodized sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy complete all as specified and directed.

S&F in repairs 75mm size butt hinges, medium weight cold rolled mild steel complete all as specified and directed.

S&F in repairs 100mm size butt hinges, medium weight cold rolled mild steel complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flaps (When open) 30 mm complete all as specified and directed.

S&F in repair continous (piano) hinges mild steel bright finish or electro galvanised width of flaps (when open) 40 mm complete all as specified and directed.

S&F in repair AI bihari hinges of 0 crank/8 crank/16 crank and standard size and screw complete all as specified and directed

S&F in repair 125mm extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repair 150mm extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repair 100mm mild steel Mortice lock, vertical type of MS 2 leavers complete all as specified and directed

S&F in repair 50 mm brass Mortice lock, vertical type of MS 2 leavers complete all as specified and directed

S&F in repair of brass CP tubular towel rail 20 mm dia 60cm long between flange with brackets etc as in repair complete all as specified and directed.

S&F in repair brass chromium plated tubular towel ring complete all as specified and directed.

S&F in repair brackets for towel rails (as per sample kept in office) complete all as specified and directed.

S&F in repairs floor door stopper of aluminium alloy body and tongue anodised with drawn steel spring fixed to door with overall length of cover plate 140mm complete all as specified and directed.

S&F in repair aluminium (extruded section body)door closer hydraulically regulated,designation No. 2, universal type, suitablefor door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed.

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty fixed complete all as specified and directed.

Welding in repair exc.2.5cm but n.exc.5cm in length of metal having thickness n.exc, 6mm complete all as specified and directed.

S&F 18-19mm thick Prelaminated particle board, interior grade, Prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work by taking out old unserviceable board from Kitchen cupboard/almiraha complete all as specified and directed.

S&F in repair plywood 6mm thick, grade BWP, type BB fixed with screw to timber frame work complete all as specified and directed

S&F in repair ball catches with 8mm dia steel ball and brass body and striking plate including letting in and fixed in wooden cabinets complete all as specified and directed.

S&F in repair 50mm dia brass polished cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed.

S&F in repair 100mm size hasp and staple aluminium anodised, safety type with mild steel hinge pin including bolt to hinge plate and fixed wiith screw complete all as specified and directed.

S&F in repair 20mm dia mild steel CP curtain rods with fixing brackets, stops etc complete all as specified and directed

S&F in repair night latch 75 mm 4 lever brass body complete all as specified and directed.

S&F in repair MS casement stay size 300mm with hinged joint and two plates with studs complete all as specified and directed.

S&F in repair Powder Coated(minimum thickness of powder coating 50 micron) aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F in repairs Powder Coated(minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing, clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed.

S&F in repairs Powder Coated(minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters (wire mesh shutter & glazed shutter), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

S&F 5 mm thick sheet glass in squares/rectangle not exc 0.50 sqm in each pane fixed with wooden beads or putty (in metal/wooden frames etc)including rubber beading complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed.

M&L for light shade 1st quality fully Vitrified tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm in floors etc set & jointed in neat cement slurry and pointed with epoxy filling using spacers 3/5mm wide (shade as approved by GE) in joints etc complete all as specified and directed.

M&L for light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular)polished, area of each tiles not exceeding 0.06 sqm,vertical surfaces as in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl10mm thick cement mortar in CM 1:4 complete all as specified and directed.

M&L for light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular)polished, area of each tiles not exceeding 0.36 sqm,vertical surfaces as in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including 10mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L for coloured joint free Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 15mm thick screed in CM 1:6 complete all as specified and directed.

M&L non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) polished, area of each tiles exc.0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic designer coloured tiles of size 450x300x 7 to 8 mm thick on vertical surface as in skirting/dado set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tiles over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for Glazed ceramic coloured tiles in vertical surface 300 X 200 X 7mm thick set and jointed in neat cement slurry over and including 10 mm thick rendering in CM 1:4 and pointed in white or colour cement to match complete all as specified and directed.

M&L for wire brushing and cleaning top surface of tiles lime terracing or cement concrete including flashing and junction of parapets etc and surface painting with a layer of blown bitumen of any penetration applied hot @ 1.7 kg/sqm blended with grit or pea size graval @ 0.006 cum per sqm and lightly tampered complete all as specified and directed.

Demolition of cement concrete (unreinforced) in Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for water proofing treatment to sunken slab complete all as specified and as directed in the following operations:- (a) Clean the surafce with mechanical grinding for remove the dust ,debris and oil deposits,remove all the loose material,like cement slurry,mortar,plaster and other unwanted particles.clean the surface with soft brush to make it clean and dust free (b) providing and laying of a 75x75mm coping with polymer modified mortar at floor wall joints wherever necessary. (c) providing and applying one coat of Asian paint smart care repair polymer or equivalent in Pidilite/fosroc/sika mixed with cement in ratio of 1:2 over the entire clean and prepared surface as a sealer coat. (d)supplying and applying two component of asian paints smartcare ultra block 2k or equivalent in pidilite/fosroc/sika acrylic polymer modified high performance coating system,brush applied,membrane with an elongation of >220% and tensile strength of 1.72MPa as per ASTM D 2370:2016,crack bridging ability of 3mm as per EN 1062-7:2004,no leakage upto a 5 bars of water presure. The system includes final base preparation,applying the coating in two coats with a total consumption of 2.25kg/sqm. (e) providing and laying 25mm thick cement sand plaster admixed with integral water proofing compound @200ml per bag of cement(1cement:4sand) flollwed by neat cement punning.Note: Water ponding test shall be carried out for 48 hrs.

M&L Plain cement concrete 1:5:10 type E-2 (using 40mm graded aggregate) as in filling of sunken portion complete all as specified and directed.

M&L PCC 1:2:4 type B 0 (using 12.5 mm graded stone aggregate) mixing with WPC levelling course in floor etc complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

M&L for machine made rubber moulded precast concrete interlocking paver block (coloured),pre polished of any shape and size with grey cement and pigment confirming to IS 15658-2006 of 60 mm thickness M-35 Grade, over and including 25mm average thickness sand cushioning complete all as specified and directed.

M&L for machine made Rubber moulded precast concrete interlocking paver block (coloured),pre polished of any shape and size with grey cement and pigment confirming to IS 15658-2006 of 80 mm thickness M-40 Grade, over and including 25mm average thickness sand cushioning complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over & including 20mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L machine cut Kota Stone slab as in flooring / landing of stairs , 18-20mm thick laid over and including 15mm thick cement screed bed in CM 1:4 , laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab and including rubbing and polishing complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18-20mm thick in staircase riser/tread/skirting dado etc jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for Granite stone 18-20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over 20mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L machine cut Granite slab 15 mm thick for steps, pillars, window cills, cooking platforms, labs counters for experimental work and like and including 10mm thick (avg thickness) CM 1:4 screeding and setting coat in CM 1:2, 3mm thick, set and jointed with white/coloured cement to match the shade of slab incl cutting, waste, rubbing and polshing etc complete all as specified and directed. Note:- (i) The rate of granite stone shall be deemed to incl for full rounded off corner/edges incl all cutting to make it square or rectangular. (ii) The rate shall also be deemed to incl for cutting and polishing machine and granite polishing to achive the desired granite finish.

Rounding to edges of stone slabs one edge such as steps cooking platform and other similar works complete all as specified and directed.

M&L for grinding and polishing old terrazo tile/kota stone and marble stone flooring and wall using wax polish to obtain mirror finish and carborundum stone of girt number 60 followed by 120/150 as desired and finishing the polish with grit number 320, surface to be cleaned with water and dried complete all as specified and directed.

S&F in repair sand cast iron soil waste & vent pipes 75mm dia in any length with or without ears with cement joint fixed to wall including necessary scaffolding upto G+7 storey complete all as specified and directed.

All as per item Ser No 158.00 above but 100 mm bore.

S&F in repair sand cast iron soil waste & vent pipes 75mm dia in any length with or without ears with cement joints laid in trenches or in floor complete all as specified and directed.

All as per item Ser No 160.00 above but 100 mm bore.

S&F stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75mm dia pipe complete all as specified and directed.

All as per item Ser No 162.00 above but 100mm dia.

Demolition of brick work or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, aches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L brick work with sub class B old size bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F Rolled mild steel Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lenghts i.e. within 20mm of the length indicated) GDE Fe 410-0 W (Gde E-250) quality A complete all as specified and directed.

S&F Mild steel bands, straps, supports or stay, for rain water, ventilating pipes including bolts if reqd, hooks (stay) heavy for large gates hook and pintle large hasps and staple, chains hand made sliding bolts clamps, hold fasts wall ties etc etc hooks for hanging fans plain angle cleats for securing purlins to wood truss or rafter, knee piece inserts, two way and three way straps, plate washer and similar small articles confirming to Fe-410-0 or Fe-310-0 complete all as specified and directed.

M&L for machine pressed pre-polished coloured chequered cement concrete tiles 30cm X 30cm X 25mm thick set, jointed and pointed in neat cement slurry in floors over and including 20mm thick screed bed or bedding layer in CM 1:6 including demolition of old tiles complete all as specified and directed.

M&L preparation of new steel & iron surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over and including one coat of primer complete all as specified and directed.

Dismantling Asbestos corrugated & Semicorrugated sheeting in roof covering of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F in repair 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with L-type or J-type or cranked bolts and washer in roof and wall etc complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings etc not exc 15 cm thick above or below ground level complete all as specified and directed.

M&L 75mm thick PCC type C-2, (1:3:6) using 40mm graded stone aggregate as in sub base to floors etc complete all as specified and directed.

M&L 100 mm thick cement concrete type D-2,1:4:8 (40mm graded stone aggt) as in sub floors, filling and mass concrete etc complete all as specified and directed.

S&F factory made chequred cement concrete coloured tiles 200mm x 200mm x 25mm thick, set jointed and pointed in neat cement slurry with grey cement mixed with pigment to match the colour of tiles, laid over and incl 20mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for applying silicon sealeant on joints of wall, cill, jambs roof, window etc. with sufficient quantity for proper sealing of joints complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for pre-cast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs,manhole cover and similar work including necessary form work complete all as specified and directed.

S&F Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including crancking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

Supply and fix mild steel round bars 10mm dia FE 410W Gde E-250 quality A or Fe 290 gde E-165 cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips for man hole cover handle complete all as specified and directed.

S&F in repairs coloured powder coated aluminium strip of size not less than 0.90 m long and 30 mm wide with brush lining fixed at bottom of wooden/aluminium door to cover gap between door and floor complete all as specified and directed.

Removing building materials etc.to a distance exc 1.50 KM of upto 20 KM, beyond the lead including loading, unloading and stacking at the destination complete all as specified and directed.

S&F in repair PVC internal kit including PVC float valve set for PVC low level flushing cistern complete all as specified and directed.

S& Fixed in repair rubber washers for low level flushing cistern complete all as specified and directed.

Supply and fix in repair PVC flush handle for low level flushing cistern complete all as specified and directed.

M&L Providing and injecting chemical emulsion for Post Constructional antitermite Treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

Providing and applying specially formulated Asian Paints SmartCare Hydroloc or quivalent in sika/Fosroc/pidilite , a one component, ready-to-use, penetrative-cum-film forming interior waterproofing solution that provides best-in-class solution to interior waterproofing problems like dampness and efflorescence. It forms a breathable, but water-tight film which doesn’t allow transport of water and salts to the surface complete all as specified and directed.

M&L for PCC 1:3:6 type C2 (using 12.5mm graded aggregate) as in plinth courses, copings, parapets, saucers drain, kneelers, apex stones, bed blocks, kerbs, water troughs including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with CM 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L preparing new concrete surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

M&L preparing old painted concrete surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

M&L for Complete removal of existing treatment including preparation of plastered or unplastered surfaces of walls incl pillasters and cornices etc. incl washing, rubbing down and stopping the previously treated surfaces and applying two coat of oil emulsion distemper of approved shade/tint over and including one coat of 1 mm thick wall care putty to achieve smooth finish complete all as specified and directed.

M&L for Complete removal of existing treatment including preparation of plastered or unplastered surfaces of walls including pillasters and cornices etc. incl washing, rubbing down and stopping the previously treated surface and applying two coat of acrylic exterior emulsion weather proof paint of approved tint / shade(s) complete all as specified and directed.

M&L complete removal of existing treatement on wall surfaces with sand paper, iron patti or grinder, including pillasters and cornices etc and applying two coat of interior acrylic emulsion paint over a coat of 1 mm thick birla wall care putty to achieve smooth finish complete all as specified and directed.

M&L complete removal of existing treatement on ceiling surfaces with sand paper, iron patti or grinder, including pillasters and cornices etc by brooming down with steel wire brushing, scraping down, smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying two coat of white wash complete all as specified and directed.

M&L preparation of old painted ceiling surfaces of any type description and applying one coat of oil emulsion distemper of approved shade/tint complete all as specified and directed.

M&L for providing Water proofing treatment to roof as under:- (a) Complete removal of existing roof treatment including brick tile, mud fusca,PCC padding,cowa, lime concrete etc up to any thickness and depth of original roof slab and Clean up to existing RCC roof by steel wire brushes and surface washed with clean water and complete all as specified and directed by Engr-in- charge. Note:- All Demolished material / mud phuska sand/ brick tiles will be taken by the contractor out side of the Defence land exc 5 km but not exc 10 km run without any extra cost to the govt. Contractor should quote his rate Keeping this Aspect in mind. (b) M&L 15 mm thick plaster in CM 1:4 over concrete surfaces of roofs finished even and smooth with WPC @ 3% by weight of cement. ( WPC will be measured and paid seperately). (c) Applying a coat of approved bituminious primer @0.25 ltr/Sqm and allow to dry conforming to IS: 3384-1965. (d) Applying bonding coat with one coat of hot blown bitumen grade 85/[email protected]/Sqm. (e) Supplying and laying APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/Sqm) laid on by torch forced application.The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction and 100mm overlap on all vertical surfaces/dado/parapets etc and sealing the overlaps by heating and fusing the layer of asphalt and melting the protective plastic film. (f) Applying bonding coat with one coat of hot blown bitumen grade 85/[email protected]/Sqm. (g)M&L for 25x25x 20 to 22 mm thick Precast cement concrete tiles type B-1, 1:2:4 (10mm to 12.5mm graded stone aggregate) slab flooring, bedded over and including screed bed 15 mm CM 1:4 , and pointed in CM 1:3. complete all as specified and directed. Note :- (i) The water proofing treatment shall be carried out by authorized approved applicators/agency of A.P.P. based polymeric membrane as approved by GE. (ii)Application of polymeric membrane shall be done by torch application. (iii)Primer shall be applied after preparing and cleaning of fully dried cement plastered surface

M&L PCC 1:2:4 type C1 using 20 mm graded stone aggregate as in mass concrete over roof as in padding incl cement slurry over old RCC surface, surface fair finished even & smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

Cutting grooves in brick wall, for inserting APP membrane and other works 75mm wide and 65mm deep and shaping horizontal face of grooves and making good with cement mortar 1:3 or PCC 1:2:4. complete all as specified and directed.

S&F Factory made precast heavy duty drain/manhole covers with MS frame and reinforcement (size Square/rectangular/circular with ring) complete all as specified and directed.

M&L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand: 2 stone chipping 10mm nominal size) in panels made by wooden beads with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified (Payment for providing grooves shall be made separately) including using white cement inplace of grey cement for grit wash complete all as specified and directed.

S&F in repair venation venatian blinds consisting of Aluminium head rail with vanes/louvers/flip cover 100 mm wide of approved tint/shade and traverse coard complete fixed in position complete all as specified and directed.

S&F in repair double rolling vertical venation blinds consisting of Aluminium head rail with flip cover of approved tint/shade and traverse cord complete as per manufacturer instruction fixed in position complete all as specified and directed.

Taking down of Old unserviceable point wiring any type for light, fan, power etc including unserviceable switch,socket, regulator light fitting and ceiling rose etc of any make complete including making good disturbed surfaces of walls ,floors roof etc complete all as specified and directed.

Taking down of Celling Fan carefully and refixing the same after Painting with synthetic enamel white paint by spraying ,greasing, minor repairing and writing MES No with synthetic enamel paint complete all as specified and directed.

M&L for Point wiring with 1.5 Sqmm multistranded copper conductor cable multistranded, FRLSH PVC insulated and unsheathed in and including PVC concealed conduit including cutting chasing for conduits and terminal boxes with all fittings /accessories and including 1.5 Sqmm PVC insulated copper earth wire connected common earth with terminal boxes for Modular fittings including acessories as modular metal flush box 2mm thick surface cover plate with frame, for one light/Fan/Exhaust Fan/bell point complete all as specified and directed.

All as per item Ser No 209.00 above but using cable size 1.5 Sqmm for 1 Nos 05 Amps Socket outlet independent with terminal boxes, Moduler fittings including acessories as moduler metal flush box 2mm thick ,surface cover plate with frame, metal flush box.

All as per item Ser No 209.00 above but using cable size 1.5 Sqmm for 05 Amps Socket outlet independent but below switch board with terminal boxes, Moduler fittings including acessories as moduler surface cover plate with frame, metal flush box.

All as per item Ser No 209.00 above but using cable size 1.5 Sqmm for 1 Nos 05 Amps Socket outlet on the same board.

All as per item Ser No 209.00 above but using cable size 2.5 Sqmm for 15 Amps Socket outlet terminal boxes for Modular switches including acessories as moduler metal flush box 2mm thick ,surface cover plate with frame, metal flush box with 2.5 sqmm earth wire.

M&L for Point wiring with 1.5 Sqmm multistranded copper conductor cable multistranded, FRLSH PVC insulated and unsheathed in PVC casing & caping double lock including fixures and terminal boxes with all fittings /accessories and including 1.5 Sqmm PVC insulated copper earth wire connected common earth with terminal boxes for Modular fittings including acessories as modular surface cover plate with frame, for one light/Fan/Exhaust Fan/bell point complete all as specified and directed.

All as per item Ser No 214.00 above but using cable size 1.5 Sqmm for 1 Nos 05 Amps Socket outlet independent with terminal boxes, Moduler fittings including acessories as moduler surface cover plate with frame, metal flush box.

All as per item Ser No 214.00 above but using cable size 2.5 Sqmm for 15 Amps Socket outlet terminal boxes for Modular switches including acessories as moduler surface cover plate with frame, metal flush box with 2.5 sqmm earth wire.

M&L for Point wiring with 1.5 Sqmm multistranded copper conductor cable multistranded, FRLSH PVC insulated and unsheathed in existing PVC coundit including fixures and terminal boxes with all fittings /accessories and including 1.5 Sqmm PVC insulated copper earth wire connected common earth with terminal boxes for Modular fittings including acessories as modular surface cover plate with frame, for one light/Fan/Exhaust Fan/bell point complete all as specified and directed.

All as per item Ser No 217.00 above but using cable size 1.5 Sqmm for 1 Nos 05 Amps Socket outlet independent with terminal boxes, Moduler fittings including acessories as moduler surface cover plate with frame, metal flush box.

All as per item Ser No 217.00 above but using cable size 2.5 Sqmm for 15 Amps Socket outlet terminal boxes for Modular switches including acessories as moduler surface cover plate with frame, metal flush box with 2.5 sqmm earth wire.

S&F in replacement plug top 16 Amps with indicator complete all as specified and directed.

S&F modular switch 6 Amp single pole one way-1 module complete all as specified and directed.

S&F modular switch 20 Amp single pole one way-2 module complete all as specified and directed.

S&F modular socket outlet shuttered 6A-2/3 Pin-universal indian 2 module complete all as specified and directed.

S&F modular socket outlet shuttered 6/16A-2/3Pin indian 2 module complete all as specified and directed.

S&F Fan step regulator 120W - 2 module complete all as specified and directed.

M&L for modular bell push 6 Amp 2 module complete all as specified and directed.

M&L in replacement in bell ding dong AC 230 Volts complete all as specified and directed.

S&F in replacement of switch piano type flush type single pole one way 5 Amps complete all as specified and directed.

S&F in replacement of socket outlet 2 in one 3 Pin 5 & 15 Amps complete all as specified and directed.

S&F in replacenent of switch piano type flush type single pole one way 15 Amps complete all as specified and directed.

S&F in replacenent of socket outlet 2 in one 3 Pin 5 & 15 Amps complete all as specified and directed.

S&F in replacenent of PVC connection 600mm long with brass Nut with rubber washer suitable hot/cold water complete all as specified and directed.

S&F in replacement of modular cover plate with frame 3 module complete all as specified and directed.

S&F in replacement of modular cover plate with frame 6 module complete all as specified and directed.

S&F in replacement LED 18/20 Watt fitting batten with decorative end cap with aluminium housing & integral electronic driver with tube 22 watt complete including connection with 1.5 Sqmm 2 core flexible copper cable complete all as specified and directed.

S&F in replacement of capacitor 2.5mfd Mfd including connection complete all as specified and directed.

S&F of exhaust fan iron body 300mm dia having 05 Blade including connection and fixing on wall with nuts bolts washers etc including taking down old unserviceable exhaust fan complete all as specified and directed. Note :- Old unserviceable exhaust fan shall be deposited in MES Store.

S&F lamp holder PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F ceiling rose 3 Phase/PVC/polycarbonate, isolated body complete all as specified and directed.

M&L for renewal of sub main wiring 2x4.0 sqmm and 1x4 Sqmm earth wire PVC insulated FRLSH multistranded copper conductor ISI marked 1100 V grade in PVC in existing concealed conduit or fixed in wall/floor, passing through wall/ceiling complete all as specified and directed.

M&L for renewal of sub main wiring 2x10 sqmm and 1x10 Sqmm earth wire PVC insulated FRLSH multistranded copper conductor ISI marked 1100 V grade in existing PVC conduit fixed in wall/floor, passing through wall/ceiling complete all as specified and directed.

S&F in replacement of heating element 1.5 KW triangular type for 25 Ltr hot water heater complete including connection complete all as specified and directed.

S&F in replacement of heating element 2.00 KW for 50 Ltr hot water heater complete including connection complete all as specified and directed.

S&F in replacement of inlet/oulet assembly to matching the existing 25/50 ltr capacity geyser including fixing and testing complete all as specified and directed.

S&F in replacement of copper water tank suitable for 25 Ltr geyser complete including proper fixing and testing after repair complete all as specified and directed.

Supply, fixing and commissioning water heater storage type 25 litres capacity, BEE 5 star and 8 bar pressure rated, with feroglass coated inner container energy saving high density PUF insulation vertical, Adjustable knob for setting the temprature ,shock safe plug to prevent electric shocks by cutting off the power in case of current leakage,2000 watt rating grouting of studs in wall in cement mortar (1:3) nuts, washers, provision of two numbers PVC braided connection 450 mm long heavy duty with brass nuts and two numbers brass chromium plated angular valve with wall flange suitable for 15mm bore pipe for water supply connection including taking out the old geyser and depositing in MES storeyard at AGE R&D Delhi complete all as specified and directed. Make:HAVELLS MONZA DX or equivt make and model of RECOLDS/USHA/BAJAJ

Supplying and fixing Ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current (BLDC) fan motor and fixing eletronic fan regulator compatible with BLDC fan including Smart remote to regulate speed and necessary materials, erected in provided hook/clamp including taking down old unserviceable ceiling fan complete all as specified and directed. Paint: Superior quality of synthetic enamel paint of specified colour for marking Sl. No and date of erection shall be used. Note :- Old unserviceable ceiling fan shall be deposited in MES Store.

S&F in replacement of exhaust fan PVC body 200mm dia with louver including connection and fixing on wall with nuts bolts washers etc complete all as specified and directed.

Sree Ram Enterprises