ADDN/ALTN AND SPECIAL REPAIRS TO EXISTING OTM ACCN AT GRC KAMPTEE

Amount

Demolition of plain cement concrete in ground floor & paving not exc 15cm thick above or below ground level complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub-base, under floors and pavings complete all as specified and directed.

Material & labour for 75mm thick PCC (1:3:6) Type C1 (using 20mm graded stone aggregate), as in plinth protection and finishing surfaces even & smooth without using extra cement including mastic filling in the joint complete all as specified and directed.

M&L for 100mm thick PCC 1:2:4 type B2 (using 20mm graded stone aggregate) as in Hard standing and similar works finished even and smooth without using extra cement complete all as specified and directed.

Forming construction joint 30mm deep x 10mm wide filled with sealing compound Grade 'A' complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for mild steel angle iron as in framed chowkats for door shutters cut to length including necessary welding and making holes for fixing butt hinges and fixing 10mm dia as tie bar confirming to Fe-410 -W (Gde E-250) quality A etc complete all as specified and directed.

S&F framed guard bars with mild steel square bars with ends of bars shouldered and/ or riveted and similar work confirming to Fe 410-O or Fe 310-0 complete all as specified and directed.

S&F mild steel hold fast and other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolt complete all as specified and directed.

Taking down existing water proofing treatment including PCC padding, mortar etc and disposal rubbish out side within MD land and hacking for key scrubbing down with water complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B0 (Using 12.50mm graded stone aggregate) as in padding over RCC roof complete all as specified and directed.

Material & labour for provision of water proofing treatment by using APP torch on mineral/ slate finished membrane over roof and vertical surfaces including preparation of surfaces and applying oil based bituminous primer coat @ 0.30 ltr per sqm on clean and dry surface and then providing APP membrane having non woven polyester film reinforcement with 3mm thick and weight not less than 3.00 kg/sq m and finished on top with mineral/slate finished torch on system laid with 100mm & 150mm over lap on side & end laps respectively and applying two coats of aluminium paint complete all as per manufacturers instructions complete all as specified and directed.

M&L for rendering 10mm thick in cm 1:4 on brick or concrete surfaces using water proofing liquid compound and finishing surfaces even & fair without using extra cement complete all as specified and directed. Note: Water proofing liquid will be measured and paid separately.

Taking down shutters only exc 1 sqm & not exc 2 sqm each complete all as specified and directed.

Taking down door/window frames incl shutters (without taking off shutter from the frames) not exc 1.50 Sqm each complete all as specified and directed.

Taking down door/ window frames incl shutters (without taking off shutter from the frame) exc 1.50 Sqm and not exc 4 sqm complete all as specified and directed.

S&F steel window with side hung shutters (glaze & gauze shutter) including projecting or box type hinges with steel handle peg stay and divided into square with glazing bars dovetailed or welded, to receive glazing or gauzing including one coat of primer including fixing of hold fast of size 25 x 5mm flat iron etc complete all as specified and directed.

All as per item No 17 above but with glazing/sash bars for fly proofing complete all as specified and directed.

S&F 35mm thick plain framed panelled factory made shutter made out of IInd class hard wood rail and styles and panel of 12mm thick veneered particle board or 9mm thick plywood with commercial veneering on both faces the size of rail and style as per IS 1083 (part-I) kiln seasoned and chemically pressure treated of any number of panel complete all as specified and directed.

S&F second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

S&F 35mm thick 2nd class HW glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats or frame etc any numbers of panels complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening complete all as specified and directed.

S&F factory made solid PVC moulded panelled door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain coloured PVC 'C' channel having PVC sheet strip of 20mm width struck inside with solvent cement for styles and colour PVC sheet for Top rail: panelling of colour PVC sheet to be fitted in the MS frame welded/sealed to the style and rail with suitable PVC sheet beading and jointed together with solvent cement etc fixed with frame at site complete all as specified and directed.

M&L for brick work with fly ash bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 (Using old size brick) complete all as specified and directed.

M&L for brick work with fly ash brick, straight or curved on plan to any radius built in half brick thick wall built in cm 1:4 (Using old size brick) complete all as specified and directed.

Taking down cement plaster, any description on brick or stone walls/ chajja/ pillars etc including raking out joints hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in two coats (10 and 5mm thick) in cm 1:4 on brick or concrete surfaces even & fair smooth, using water proofing liquid compound and without using extra cement complete all as specified and directed. Note: Water proofing liquid will be measured and paid separately.

Supply only liquid integral water proofing admixture of make pidilite or its equivalent complete all as specified and directed.

M&L for rendering 10mm thick CM 1:6 on brick or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding, but not backing removing and rubbish off the premises up to 1 KM complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed or bedding layer in CM 1:4 finished even and fair for laying floor finishes/tiles etc complete all as specified and directed.

M&L for 8 to 9mm thick vitrified ceramic tiles (Square/ rectangular) polished, area of each tiles not exc 0.36 sqm, in floors/skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding/rendering layer 10-15mm thick mortar in CM 1:4 finished even and fair for laying floor finishes complete all as specified and directed.

All as per item No 32 above but in skirting/dado over and including rendering 10mm thick in CM 1:3 as backing coat to receive tiles complete all as specified and directed.

M&L for coloured glazed ceramic wall tiles 300 x 450 x 7mm thick, on vertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles over and including rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 as backing coat to receive wall tiles/ skirting/ dados complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4), type B0 (using 12.5mm graded stone aggregate) as in sunken floor using liquid integral WPC @ 200 ML/50Kg of cement (WPC shall be measured and paid separately) complete all as specified and directed.

M&L for PCC (1:5:10) type E2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for 15mm thick screed bed or bedding layer of cement plaster 1:4 mixed with water proofing compound for sunkan floor treatment finishing even and smooth without using extra cement complete all as specified and directed. (WPC will be paid separately).

M&L for two coats of brush bond liquid compound of make Sika/ fosroc (Sika/Fosroc chemical Ltd) or its equvalent water proofing coating over plastered surfaces of sunken portion as per manufacturer's instructions complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

M&L for pre-polished granite slab, machine cut of any shade as approved by GE of 18 to 20mm thick including necessary notching, chamfering the edges over and including cement screed bed including cutting, grinding and mirror polishing (Granite finish) with suitable grinding stones complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platforms and other similar situations complete all as specified and directed.

M&L for 18-25 mm thick kota stone (machine cut) slab flooring laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, mirror polishing over and including screed bed 20mm thick in CM 1:3 complete all as specified and directed.

Material & Labour for Kota stone slab 12-20mm thick in riser of steps, skirting, dado and pillar laid over and including backing coat of 10mm cement screed in CM 1:3 complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B-0 (Using 12.5mm graded stone aggregate) as in levelling course, fair finished to receive floor finishes complete all as specified and directed.

Material & labour plain cement concrete type 1:2:4 B1 using 20mm graded stone aggregate as in coping, haunching rounded or chamfered on edges including necessary from work complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F in repair PVC (SWR) bends any radius for 110mm bore complete all as specified and directed.

S&F in repair PVC (SWR) bends any radius for 75mm bore complete all as specified and directed.

S&F in repair PVC (SWR) branch piece single Y equal or unequal for 110mm bore complete all as specified and directed.

S&F in repair PVC (SWR) branch piece single Y equal or unequal for 75mm bore complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exc 10cm girth complete all as specified and directed.

S&F PVC (SWR) / rain water pipes 150mm dia single socketed in any length with rubber ring joints fixed to walls (including taking down existing pipe of any description) complete all as specified and directed.

S&F PVC (SWR) bends any radius for 150mm bore complete all as specified and directed.

Taking up or down steel tubing 15mm bore and connections complete all as specified and directed.

Taking up or down steel tubing 20mm bore and connections complete all as specified and directed.

Supply & fix GI tubing 15mm bore medium grade with all fittings and fixed to wall/ceiling or laid in floors complete all as specified and directed.

Supply & fix GI tubing 20mm bore medium grade with all fittings and fixed to wall/ceiling or laid in floors complete all as specified and directed.

S&F PVC (SWR) Nahani trap 75mm dia with grating including jointing to waste pipe, fixed in cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) complete all as specified and directed.

S&F vitreous china squatting pan, ‘Orissa’ pattern of size 580x440mm with integarals foot rests (excluding cistern and flush) type including all fixtures complete all as specified and directed.

Supply and fixing PVC valve less symphonic action type flushing cistern 10ltr capacity low level, white/coloured with inlet ball valve float and handle including bracket (incl. taking down old cistern) complete all as specified and directed.

Supply and fixing in repair brass chromium plated shower rose 125mm size with or without swivel joint any size incl fixing to steel pipe or union complete all as specified and directed.

Supply only flush pipe of polythene of low or high density 32mm PVC for low level flushing cistern complete all as specified and directed.

Supply only PVC connection 15mm dia, 450-600mm long including brass ferrules on both ends complete all as specified and directed.

Supply only low density PVC pipe 32/40mm dia as in waste pipe to sink/WHB complete all as specified and directed.

S&F in repair towel rail of make Prayag Cat No BA-30 or equivalent complete all as specified and directed.

S&F in repair bib taps, chromium plated with crutch or butterfly handle, fancy type, screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair 15mm dia stop valves, fancy type and chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and directed.

S&F in repair 15mm dia stop valves, fancy type and chromium plated with long shank and cup (concealed type) screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and directed.

S&F in repair 15mm bore pillar taps, cast copper alloy, with capstan heads, chromium plated, swan neck screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets,connecting union overall size 915mm x 460mm with bowl size 410mm x330mm x 160mm complete all as specified and directed.

S&F in repair vitreous china wash basin, white, flat back, size 630x450mm counter sunk oval type fixed in granite excluding taps, waste, chain and plug and porcelain stopper complete all as specified and directed.

Dismantling water tank of capacity 5000 ltrs and removing to store of any description complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks 6 layers (cylindrical vertical with closed top) of 5000ltr capacity, hoisted and fixed in position including dismantling of existing water tank complete all as specified and directed.

M&L for preparation of old decorated surfaces and applying two coats of exterior grade weather proof paint over a coat of primer, water based on wall surfaces complete all as specified and directed.

Material & labour for preparation of newly plastered surfaces of wall & applying two coats of Apex paint over a coat of cement primer complete all as specified and directed.

M&L for complete removal of existing treatment of walls and applying two coats of oil bound distemper over a coat of Birla white wall care putty complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for preparation of old wooden surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over coat of primer complete all as specified and directed.

M&L for preparation of old steel surfaces of any description over 10cm width or girth & applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperature 1.40mm dia complete all as specified and directed.

S&F 100mm long mild steel medium weight cold rolled butt hinges and fixed with screw/ welded to frames etc complete all as specified and directed.

S&F in repair 125mm extruded aluminium handles fabricated type anodised etc complete all as specified and directed.

S&F in repair 250mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed complete all as specified and directed.

S&F in repair 150mm long aluminium anodised, barrel tower bolt of extruded section complete all as specified and directed.

S&F in repair 75mm long aluminium anodised, barrel tower bolt of extruded section complete all as specified and directed.

M&L for hacking out old broken glass any thickness size and quality from wooden /steel frames etc complete all as specified and directed.

S&F sheet glass ordinary quality, 3mm thick and glazing with oil putty in square not exc 0.50 Sqm in each pane complete all as specified and directed.

S&F 3mm figured glass, pin head type and glazed with oil putty in sqm not exc 0.50 sqm in each pane complete all as specified and directed.

S&F anodized aluminium door shutters aluminium (powder coated of any colour, (thickness or powder coating not less than 50 micron)) section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and directed.

S&F anodized aluminium windows and ventilator shutters (powder coated of any colour (thickness or powder coating not less than 50 micron)), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no) hinges type B-21, 100mm long (2 nos) suitable handle (1 no) complete all as specified and directed.

S&F sheet glass ordinary quality, 4.00mm thick and glazing with oil putty in square not exc. 0.50 Sqm in each pane complete all as specified and directed.

S&F for sheet glass 5.50mm thick tinted quality and glazing exc 0.50 sqm in each pane complete all as specified and directed.

S&F brass mortise lock (4 levers), vertical type, size 100mm long including all fitting arrangements complete all as specified and directed.

S&F Heavy duty aluminium body floor door spring (ISI marked) suitable for aluminium swing doors, double action type including necessary cutting in floors and making good to match with the existing surface complete all as specified and directed.

M&L for ball brass valves, high pressure with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed 20mm bore complete all as specified and directed.

S&F for vitreous china urinal, full stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

M&L for 20mm thick marble machine cut in skirting/ dado/ cill/ lintels /floor/jambs laid over & including cement screed bed 15mm thick in CM 1:4 and jointed with grey cement slurry including cutting and polishing of type as approved complete all as specified and directed.

S&F 20mm thick solid PVC boarding of Make Rajshree or equivalent as in partition of interior grade complete all as specified and directed.

S&F 25mm dia curtain rod of approved quality including cutting and fixing to curtain brackets complete all as specified and directed.

S&F fancy type curtain brackets of approved quality fixed to wall with screws complete all as specified and directed.

M&L for running welding in repairs including cleaning and preparing surfaces for welding, thickness of metal to be welded not exc 6mm such as MS butt hinges to MS frame, broken steel windows or ventilator, iron doors and similar work complete all as specified and directed.

Taking down point wiring with aluminium conductor cable (light, fan, socket or power & bell) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. including wooden battens /casing /capping and conduit etc and making good disturbed surfaces of walls, floors, ceilings etc. complete all as specified and directed.

Taking down sheet metal enclosure, DB, MCB, main switch etc and making good disturbed surfaces to match with existing surfaces complete all as specified and directed.

Taking down sub main wiring of any size/ capacity complete all as specified and making good disturbed surfaces to match with the existing surfaces complete all as specified and directed.

Material and labour for point wiring 1100 volt grade single core FRLSH PVC insulated and unsheathed cable with multi stranded copper conductor 1.50 sqmm drawn in and including electrical grade PVC conduit not less than 20mm dia with IS 9537 (Part-III) 1983 marked medium grade concealed on surface of wall/ceiling including FRLSH PVC insulated unsheathed earth wire with multi stranded copper conductor of size 1.50 sqmm pressed steel modular boxes sunk on wall for mounting of modular switches, switch sockets, fan regulator etc including modular cover with frame any size complete all as specified and making good disturbed surfaces for one light point controlled by one, one way switch complete all as specified and as directed. Note:- Cost of cable provided from sub main DB to respective switch board in rooms shall be included in the quoted point wiring rate. All switches, fan, sockets, ceiling roses and holders shall be connected to common earth dolly.

Material and labour for ceiling/Exhaust fan point controlled by one switch and regulator with cables 1.5 sqmm size complete all as specified and directed.

Material and labour for one 3 pin socket outlet 5 amps on the same board with other switches, with cables 1.5 sqmm size complete all as specified and directed.

Material and labour for One 3 pin socket outlet, 5 amps on independent board, complete all as specified and directed

All as per item No 110 above but wiring with 2.5 sqmm multi stranded cable and earth wire with copper conductor of size 2.5 sqmm for 15 amps power point complete all as specified and directed.

All as per item No 110 above but wiring with 4.0 sqmm multi stranded cable and earth wire with copper conductor of size 4.0 sqmm for 15 amps power point complete all as specified and directed.

Material and labour for sub main wiring with two single core PVC FR LSH insulated unsheathed stranded copper conductor and earth wire 1100 volt grade and drawing into PVC conduit not less than 20mm medium grade concealed in wall of size 2x4.0 Sqmm with earth wire of 1x4.0 Sqmm complete all as specified and directed. Note:- (i) Accessories for point/sub main wiring like PVC junction box, bend, Tee, elbow shall be of same make. (ii) 3 runs of wire & one run of conduit shall be considered as one unit.

All as per item No 116 above but of size 2x6 sqmm with earth wire 1 x 6 sqmm complete all specified and directed.

All as per item No 116 above but of size 2x10 sqmm with earth wire 1 x 10 sqmm complete all specified and directed.

All as per item No 116 above but of size 4x4 sqmm with earth wire 2 x 4 sqmm complete all specified and directed.

Supply and fix ceiling rose, surface type, 2/3 terminals, 5 amps complete all as specified and directed.

Supply and fix modular switch single pole one way 6A, 1 module, 250 volts suitable for modular switch boxes complete all as specified and directed.

Supply and fix modular switch single pole one way 6/16A, 3 pin, 250 volts suitable for modular switch boxes complete all as specified and directed.

Supply and fix modular socket single pole one way 6A, 2 module, 2/3 pin, 250 volts suitable for modular switch boxes complete all as specified and directed.

Supply and fix modular socket single pole one way 6/16A, 2 module, 2/3 pin, 250 volts suitable for modular switch boxes complete all as specified and directed.

Supply and fix 0-4 step single pole 2 module modular type electronic type regulator for ceiling fan of 1200/1400mm sweep, 120 watt 240 volts complete all as specified and directed.

Supply and fixing LED tube light wall/ceiling mounted, minimum capacity 18W LED, 220V, box type tube light with system lumens with efficacy >115lm/W at system level (including the driver loss). The luminaire should have cool day light colour temperature of 6500K CRI>80, life 40000 burning hrs with 70% lumen maintenance, PF>0.95, surge protection of 0.2KV, all photometrical and electrical parameters must be supported by LM 79-80 test report from NABL accredited lab or UL switching cycle of 50000 times, lamp starting time not more than 1 sec, the LED tube light must confirm to applicable IS 10322/EN 60598: housing of batten should be made from single piece powder coated CRCA steel sheet complete all as specified and directed.

Supply and fix LED luminaire 600mm x600mm, 35/36 W rated voltage 220V, AC surface type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver, three core flexible copper conductor cases of suitable size complete all as specified and as directed.

Supply and fix building security light LED 25 W with Lumen O/P 1800 with driver with rated voltage 240 V, 50Hz, including mounting GI made out of 25 mm dia light grade pipe 0.8 m bent two shape including FI clamps nut bolts etc complete all as specified and as directed.

Supply and fixing LED tube light wall/ceiling mounted, minimum capacity 9W LED, 220V, box type tube light with system lumens with efficacy >115lm/W at system level (including the driver loss). The luminaire should have cool day light colour temperature of 6500K CRI>80, life 40000 burning hrs with 70% lumen maintenance, PF>0.95, surge protection of 0.2KV, all photometrical and electrical parameters must be supported by LM 79-80 test report from NABL accredited lab or UL switching cycle of 50000 times, lamp starting time not more than 1 sec, the LED tube light must confirm to applicable IS 10322/EN 60598: housing of batten should be made from single piece powder coated CRCA steel sheet complete all as specified and directed.

Supply and fix sheet metal enclosure single pole & neutral for 240 volts 8 way with 200 Amp rated bus bar flush /surface mounting double door including taking down old enclosure complete all as specified.

Supply and fix MCB single pole and neutral 240 volt 6 to 40amps 10 KA breaking capacity, 'C' series, complete all as specified and as directed.

Supply and fix MCB single pole 240 volt 6 to 40 amps 10 KA breaking capacity, 'C' series, complete all as specified and as directed.

Supply and fix MCB triple pole 415 volt 6 to 40 amps 10 KA breaking capacity, 'C' series, complete all as specified and as directed.

Material and labour for earthing complete with galvanized iron or steel earth plate electrode 600x600x6mm thick burried directly in ground (earth plate not less than 2.25mtr deep below normal ground level) with top edge of the plate not less then 1.50 mtr. below the normal ground level connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washer of galvanized iron or steel all as shown in electrical plate No 3 connected to earthing test point all as specified and testing on completion including the Material and labour for :- (a) Excavation and earth work or drilling hole for electrode in any type of soil (b) PCC pit in cement concrete 1:2:4 type B-1 (c) Pre cast RCC cover with suitable handle 40mm thick in PCC 1:2:4 reinforced with welded steel wire fabric (d) Funnel with watering pipe of GI 20mm nominal bore light grade and copper lugs etc all as specified. (e) 15mm nominal bore medium grade GI protection pipe 7.50 meter long for protection of earthing lead. (f) Requisite quantity of charcoal and common salt (g) Connection to earthing test point and testing on completion.

Supply and fix exhaust fan, steel body AC single Phase 230V of size 300m sweep with, three blades and frame and louvers shutter complete all as specified and directed.

Supply and fix rigid non-metallic 32mm dia PVC conduit inclusive of boxes, junction/terminal all tees, bend, elbow, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipes, hook etc concealed on surface of wall and making good including taking down existing TV, telephone, signal cable and reused in given non metallic PVC conduit complete all as specified and directed.

Removing existing serviceable LED lights fittings and re-fixing the same as directed complete with connection from ceiling rose and making functional complete all as specified and directed.

S&F fitting with surface/recessed mounted downlighter round 12W inbuilt driver with rated voltage 240V, 50Hz complete all as specified and directed.

Supply and fix sheet metal enclosure single pole & neutral for 240 volts 4/6 way with 200 Amp rated bus bar flush /surface mounting double door including taking down old enclosure complete all as specified.

Supply and fix sheet metal enclosure triple pole & neutral for 415 volts 4 way with 200 Amp rated bus bar flush /surface mounting double door including taking down old enclosure complete all as specified.

NOTE : SCHEDULE OF CREDIT (Amount on page No 49 shall be deducted offline from the total quoted amount to arrive at the net contract sum to be considered for acceptance.)

S R BUILDERS (BID ID -3358475)

chronicle enterprises (BID ID -3346357)

sunway associates (BID ID -3350477)

VIJ ASSOCIATES (BID ID -3358201)

Devika Constructions (BID ID -3349406)

INDUS ENGG AND CONST CO (BID ID -3358209)

Bidder Name

INDUS ENGG AND CONST CO

chronicle enterprises

Devika Constructions

sunway associates

VIJ ASSOCIATES

NORTH INDIA PEST CONTROL

S R BUILDERS