Toilet block, Keezhagaraharam

Amount

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.- All work upto plinth level -1:2:4 (1 cement:2coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.- All work upto plinth level -1:5:10 (1 cement:5coarse sand : 10 graded stone aggregate 40mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level 1:5:10 (1 cement : 5 coarse sand : 10 graded brick aggregate 40mm nominal size).

Providing and fixing ISI marked Powder coating .pressed butt hinges with necessary screws etc.complete - 100x58x1.90mm

Providing and fixing ISI marked powder coating tower bolt black finish , (barrel type) with necessary screws etc. complete: - 250 x 10mm

Providing and fixing ISI marked powder coating. tower bolt black finish , (barrel type) with necessary screws etc. complete: - 150 x 10 mm

Providing and fixing ISI marked powder coating handles conforming to IS : 4992 with necessary screws etc.complete : 125mm

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with nuts and screws etc.complete:- 250x16mm

Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2nos.of 150mm long brackets of 15x15mm M.S.square tube, the vertical door profiles to be reinforced with 19x19mm M.S.square tube of 19 gauge,EPDM rubber gasket weather seal to be provided through out the frame.The door frame to be fixed to the wall using M.S.screws of 65/100mm size complete as per manufacturers specification

Providing and fixing to existing door frames - 30mm thick factory made solid both side prelam panel PVC door shutter consisting of frame made out of M.S.tubes of 19 gauge thickness and size of 19mm x 19mm for stiles, top & bottom rails.M.S.frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5mm thick heat moulded prelam PVC 'C channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on either side forming stiles; and 5mm thick , 95mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, button and lock rails shall be provided either side of the panel. 10mm (5mmx2) thick, 20mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, panelling of 5mm thick both side prelam PVC sheet to be fitted in the M.S.frame welded / sealed to the stiles & rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'C channel using PVC solvent adhesive etc.complete manufactures specification & drawing

Providing and fixing 1st quallity ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture of approved make (Jhonson / Asian / Somany / Nitco) in all colours, shades of size 200 x 300 mm as approved in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm. Including pointing in white cement mixed with pigment of matching shade complete. - size 200x300mm

Providing and laying rectified ceramic rustic / matt finish floor tiles 300x300 mm or more (thickness to be specified by the manufacturer ) of 1st quality conforming to IS:15622 of approved make ( Somany / Nitco) in all colours shades laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigments etc., complete

Providing and fixing unplasticised - PVC clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4(1 cement : 4 coarse sand) and making good the wall etc. complete. 110mm

Applying one coat of cement primer of approved brand and manufacture on wall surface - Cement primer

White washing with lime to give an even shade - Old work (two or more coats).

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade - One or more coats on old work.

Demolishing lime concrete manually / by mechanical means and disposal of material within 50 metres lead.

Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead - 1:3:6 or richer mix.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 m lead – Of area 3 sq. metres and below.

Providing and fixing white vitreous china water closet squatting pan (Indian type) Orissa pattern WC pan of size 580 x 440 mm.

Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings i/c fixing he pipe with clamps at 1.00m spacing. This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall) - 20mm nominal outer dia pipes

Providing and fixing brass stop cock of approved quality - 20 mm nominal bore.

Providing and fixing gun metal gate valve with CI wheel of approved quality (screwed end) - 25 mm nominal bore.

Providing and fixing on wall /column face unplasticed - PVC soil and waste pipes (type-B) conforming to IS:13592-1992 including jointing with seal ring conformation to IS: 5382 leaving 10mm gap for thermal expansion - single socketed pipes 110mm diameter

Providing and fixing on wall face/column face unplasticised - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735 – 1999 including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion - Single tee with door - 110x110x110mm

Providing and fixing on wall face /column face unplasticised - PVC moulded fittings/accessories for unplasticisd – PVC soil and waste pipes conforming to IS:14735- 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend with door 110mm

Providing and fixing in position G.I. Hex nipple (UNIQUE/R Brand/HB Brand/UI Brand) conforming to IS 1239 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 20 mm dia.

Constructing brick masonry manhole with 35 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design - inside size 90 x 80 cm and 45 cm deep including C.I. cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 kg. (weight of cover 23 kg. and weight of frame 15 kg) – with bricks of class designation 35.

R MAGESHWARI

P. Seethapathy