SPL REPAIRS M O TO UG SUMP 06 NOS AT SELECTION CENTRE SOUTH BANGALORE AND PROVN OF RAIN WATER DRAINAGE FACILITIES TO CERTAIN MD ACCN BLDGS AT BAIRD BARRACK AND PROVN OFF MOSQUITO PROOFING FOR 69 3 69 4 69 5 69 6 69 7 OR MD ACCN AT SELECTION CEN

Amount

Taking down cement plaster of any description of brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water, etc, complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surface and finished the surfaces fair and even to receive tiles.etc complete all as specified and directed.

M &L for providing cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) in padding concrete and finish the surface even smooth without using extra cement complete all as specified.and directed

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 incl finished surface fair and even with using WPC complete all as specified. ( WPC shall be measured and paid separately)

Supply only integral wate proffing compound ISI Marked as approved, all as specified and as directed

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground floor) complete all as specified & directed

M&L for 40 mm thick cement concrete type B-1, 1:2:4 (using 20 mm graded crushed stone aggregate), as in sub base of floors.complete all as specified & directed

M&L for preparations of newly plastered surfaces and applying two coats of Epoxy cementitious water proof coating on water side surface of water retaining structures complete all as specified.and directed Note: Application of Epoxy cementitious water proof coating shall be as per manufacturers instruction and as directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified.and directed

M&L precast cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in block masonry with solid blocks, exc 10 cm in width and setting in mortar complete 1:4 complete all as specified.and directed

M&L providing precast cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) in landings, cover slabs (for manholes etc) chullah hoods, chajjas, water troughs setting with cement mortar 1:4, complete all as specified and directed.

M&L for 75 mm thick, PCC 1:3:6 type C1 (using 20mm graded stone aggregate), surface finished even and smooth without using extra cement.as in plinth protection incl joints filling complete all as specified.and directed

M & L for hardcore of gauge n.exc 63 mm broken stone or boulders, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true sruface complete all as specified.and directed.

M&L for 75 mm thick cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggt) as in sub base etc complete all as specified & directed

M&L for screed bed or bedding layer of cement mortar 1;6 of 20 mm thick for laying floor finishes complete all as specified & directed

M&L for 20 to 25 mm thick coloured glossy finished factory made designer tiles/pavers, set and jointed & pointed in neat cement slurry as in path/floor etc complete all as specified & directed by Engineer-in-Charge. (Make : Bharat Tiles /Ultra/Endura) Note : The size, colour & combination of tiles as approved by GE.

M&L for complete removal of existing treatment and applying two coats of distemper over a coat of alkai resistant primer on wall complete all as specified.and directed

M & L for preparing new treated surfaces of walls and applying two coats of acrylic (antifungal) exterior grade paint over one coat of primer complete all as specified.and directed

Excavation in trenches n. exc 1.5 mtr wide and n exc 1.5 mtr deep for foundation and getting out in hard/dense soil complete all as specified & directed

M&L PCC 1:3:6ype C-2(using 40mm graded stone aggregate) as in surface channels and foundation of drains complete all as specified & directed..

M & L for plain cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in surface channels and drains complete all as specified and directed.

M&L for extra for forming fair finished drain or channel 45 cm inner girth in cement concrete using extra cement, incl forms, moulds, mitred/stoped ends etc complete all as specified & directed

M&L for PCC 1:2:4 type B1 using 20mm stone graged aggregate for coping complete all as specified & directed

M & L for rendering 15mm thick for internal surfaces of drain using cement plaster 1:4 to be finished even and smooth without using cement complete all as specified & directed

Returning filling including spreading levelling watering and well ramming in layers not exceeding 25 cm complete all as specified & directed

Removing excavated material, exc 1.5 KM and n. exc 5 KM out side MD land complete all as specified & directed

M&L for preparation of newly plastered surfaces of wall and applying two coats of white wash.complete all as specified & directed

S&F for mild steel TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (anealed) not less than 0.9 mm dia or securing with clips.

S&F 30 mm thick 2nd class hard wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing galss, etc., size of member of shutters as specified in SSR Pt-I, section 8, clause 8.24 (b).complete all as specified & directed

S&F second class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chemfered, put together with glue pinned at joints, supplied and fixed.

S&F for 200 mm long aluminium anodised barrel tower bolts and extrude section and fixed.complete all as specified & directed.

S&F for 150 mm long aluminium anodised barrel tower bolts and extrude section and fixed.complete all as specified & directed

S&F for 300 mm long aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips or sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast aluminium ally fixed.complete all as specified & directed

S&F for 125 mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B-21 complete all as specified & directed

S&F for100 long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B-21complete all as specified & directed

S&F for 125 mm long extruded aluminium alloy handles, fabricated type anodised complete all as specified & directed

S&F for 150 mm long extruded aluminium alloy handles, fabricated type anodised complete all as specified & directed

M&L preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.and directed.

M/S Bhagyawanticonstruction