CWE/P-13/2020-21 SPECIAL REPAIR TO CAPT MD ACCN BLOCK NO P-03 (01 TO 04 ) AT BASOLI UNDER GE BASOLI

Amount

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and as directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5 Sqm each including taking out holdfast complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5Sqm and not exceeding 4Sqm each including taking out hold fast complete all as specified and directed.

M&L 1.25mm thick pressed steel frames with one shop coat of red oxide primer 125 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges (ISI marked), lock strike plate, and hold fast after tarring of hollow portion of frame complete all as specified and directed.

M&L 1.25mm thick pressed steel frames with one shop coat of red oxide primer 105 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges (ISI marked), lock strike plate, and hold fast after tarring of hollow portion of frame complete all as specified and directed.

M & L Plain cement concrete 1:3:6 type C-1(using 20mm graded crushed stone aggregate) as in back filling hollow of frame , complete all as specified.

M&L Plain framed factory made 35mm thick shutter of 2nd class hard wood rail & style (two panel) with lock rail and panel of 9mm BWP commercial plywood or 12 mm veneered particle board with commercial veneering on both faces , the size of rail and style as per IS 1003 (Part-1) kiln seasoned and pressure treated including one coat of pink primer all as specified.

M&L Glazed and skelton shutters factory made 35mm thick of 2nd class hard wood rail & style open rebated and prepared to receive glass or wire gauze etc. shutters (without sash bars), size of members of shutters as specified in SSR Part-1, secton 8, clause 8.24(a) kiln seasoned and pressure treated including one coat of pink primer all as specified.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixed complete alll as specified and shown in relevant drg

M&L Factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with Particle Board Core 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on front face & 2mm Plain colour PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing.

M&L 18 to 20mm thick PVC board prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws as in cup board shutters, frame and shelves, complete all as specified.

M&L "Steel window factory made double shutter and tubular moulded frame of 16 gauge suitable for double shutter as per drg No CEPZ/TD/245/01 sheet 1/1 and CEPZ/TD/246/01 sheet 1/2 (double for mosquito proof one glazed with glazing bars and one gauged without glazing bars ) with side hung shutters including projecting type hinges non friction with 3mm thick 100mm long handle and two nos tower bolts 100mm long welded on 3.0mm thick MS plate to each window shutter and including hold fast and painting with one shop coat of zinc chrome primer." complete all as specified.

M&L Framed work such as grills, grating etc with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars, barrel, iron doors, ladders, balusters, walkway, frame work of water tanks and similar work confirming to Fe-290 Gde E-165 complete all as specified.

M&L 3.00 mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified.

M&L Galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified.

Preparation new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint of colour as approved by GE complete all as specified.

Preparation new wooden surfaces of any description not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer of colour as approved by GE complete all as specified.

Supply and fixing hasp and staple,75 mm long aluminium anodised, including bolt to hinge plate and fixed with screws complete all as specified. ISI Marked

Supply and fixing butt hinges of size 100mm (ISI marked), mild steel cold rolled medium weight, complete all as specified.

Supply and fixing Extruded aluminium alloy handles, fabricated type, anodised of size, ISI marked 125mm and fixed, complete all as specified and directed.

Supply and fixing Aluminium anodised, barrel tower bolts of extruded section of size 150mm ISI marked and fixed, complete all as specified and directed.

Supply and fixing in repairs, 300mm mild steel ordinary rat tail rod pattern springs ISI marked including roller and roller plate fixed in repair complete all as specified.

Supply and fixing mild steel barrel tower bolt ISI marked, stove enamelled black, with bright bolt of 150mm long, complete all as specified.

S & F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section and fixed, all as specified and directed.

Supply and fixing Harrison rails(Curtain rails) (ISI marked), mild steel chromium plated wih fixing brackets, stops, rollers etc. all as specified.

M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement incl taking down cement plaster on brick or concrete surfaces in any description etc incl raking out joints, hacking for key , scrubbing down with water complete all as specified and directed.

Material and labour rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement incl taking down cement plaster on brick or concrete surfaces in any description etc incl raking out joints, hacking for key , scrubbing down with water complete all as specified and directed.

M&L rendering 05 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 as in ceiling finished even and smooth without using extra cement incl taking down cement plaster on brick or concrete surfaces in any description etc incl raking out joints, hacking for key , scrubbing down with water complete all as specified and directed.

M & L preparation of new plastered surfaces of walls and applying two coats cement base paint of approved brand and colour as approved by GE all as specified and as directed .

M & L preparation of new plastered surface of wall and applying a coat of wall care putty 3mm thick and two coat of oil bound distemper complete all as specified

M & L applying three coats of white wash including preparation of newly plastered surfaces of ceiling complete all as specified.

M & L preparation of old plastered surfaces of walls and applying one coats cement base paint of approved brand all as specified and as directed .

M & L preparation of old treated surface of wall and applying a coat of wall care putty 3mm thick and two coat of oil bound distemper complete all as specified

M & L applying one coat of white wash including preparation of old plastered surfaces of ceiling complete all as specified.

M&L Plain Cement Concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate), 75mm thick as in plinth protection etc laid in alternate bays finishing even and smooth without using extra cement complete all as specified.

M&L 40 mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in floor finishing surface even and smooth without using extra cement,complete all as specified and as directed.

M&L Glazed ceramic coloured tiles in skirting/dado 350 x 250 x 7mm or 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match required shade over and including 10 mm thick cement plaster in cement mortar 1:4 as in backing coat rough finished surface including dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

M&L 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in sub base to flooring etc, complete all as specified.

M&L Non-skid ceramic coloured tiles 7 to 8 mm thick (square / rectagular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over screed bed 15 mm thick in cement mortar 1:4 including dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, size of each slab not be less than 0.28 Sqm, including rubbing and mirror polishing complete including 15mm thick screed bed in cement mortar 1:4 complete all as specified.

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over including cement screed in cement mortar 1:4, and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing & complete aggregate all as specified & directed.

M&L 18 to 20mm thick granite (of approved type colour) work (table rubbed & polished) in jambs, pillars, window cills, cooking plateform laid over and including 15mm thick cement screed (1:4) and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the colour of granite stone including cutting and moulding the edges where ever directed by Engr-in-charge, complete all as specified.

M&L PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sunken portion all as specified and directed by Engr –in Charge

Supply and fixing in repairs, Vitreous china squatting pan (Orissa pattern) size 580 x 450 mm, white, with integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe of 32mm dia and syphonage pipe etc, and complete, all as specified and as directed.

S & F in repairs vitreous china wash down water closet pan (Pedestal Pattern ) white including fixing bolts, plastic water closet seat, white, closed pattern, solid type with flat bottom, and cover and mild steel chromium plated hinging device complete and including making good to floor to match with adjoining surfaces complete all as specified and as directed

Supply and fixing Vitreous china Wash hand basin, coloured, flat back of size 550x400mm including brackets, brass chromium plated waste coupling of PTMT(half or full threaded), and waste pipe PVC 32mm dia (min weight 45 gms) including cutting for and pinning in ends of brackets or erecting stand etc fixed in repair, complete all as specified.

Supply and fixing Rotational moulded polythene water storage tank, coloured, tripple layer cylindrical vertical with closed top 500 litre capacity hoisted and fixed in position, including inlet and outlet pipe connections, 20mm dia and 15 mm dia GI pipes medium grade respectively, 20mm GI pipe medium grade over flow pipe 15 cm long wash out with plug and brass ball valve 20mm, high pressure with polyethelyne float and fly nuts including dismantling existing water tanks and removing from site capacity exceeding 250 ltr and not exceeding 500 ltr complete all as specified and directed.

Supply and fixing Rotational moulded polythene water storage tank, coloured, tripple layer cylindrical vertical with closed top 1000 litre capacity hoisted and fixed in position, including inlet and outlet pipe connections, 20mm dia and 15 mm dia GI pipes medium grade respectively, 20mm GI pipe medium grade over flow pipe 15 cm long wash out with plug and brass ball valve 20mm, high pressure with polyethelyne float and fly nuts including dismantling existing water tanks and removing from site capacity exceeding 500 ltr and not exceeding 1000 ltr complete all as specified and directed.

Supply and fixing in repairs, PVC valve less symphonic action type flushing cistern 10ltr capacity ISI marked, low level white with inlet ball valve float and handle including brackets including 32mm dia PVC flush pipe for low level cistern including all joints fixed, complete all as specified.

Supply and fixing in repairs, 100 mm dia cast iron 'P' or 'S' trap ISI marked complete all as specified.

Supply and fixing in repairs, PVC (SWR) floor trap of 75mm dia of outlet, plain with grating including jointing to waste pipe with solvent cement fixed in cement concrete 1:2:4, type B-1 complete all as specified.

Supply and fixing in repairs, 100 mm dia cast iron soil waste and vent spun pipe ISI marked in any length with or without ears with lead joints laid in floor/wall, complete all as directed

Supply and fixing in repairs, 75 mm dia cast iron soil waste and vent spun pipe ISI marked in any length with or without ears with lead joints laid in floor/wall, complete all as directed

Supply and fixing in repairs, Cast iron bends (any radius) diminishing pieces or tapers (larger bore measured), bore of pipe 100mm ISI marked, complete all as specified.

Supply and fixing in repairs, Cast iron bends (any radius) diminishing pieces or tapers (larger bore measured) ISI marked, bore of pipe 75mm, complete all as specified.

Supply and fixing in repairs, Cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branchs, ISI marked, bore of pipe 100mm, complete all as specified.

Supply and fixing in repairs, Cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branchs, bore of pipe 75mm, complete all as specified.

M&L PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint fixed to walls as drainage pipe complete all as specified and directed.

M&L PVC connection 15mm size with PTMT nuts on both ends of length 450mm , complete all as specified.

M&L Shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 300gms) complete all as specified and directed.

M&L Tubular towel rail, ISI marked 60cm long between flanges , 20mm dia D type Brass Chromium plated incl necessary brackets, fixed with chromium plated screws and wooden/plastic cleats complete all as specified and directed.

S& F grating round 140 mm size of PTMT.(Minimum weight 50gms)complete all as specified and directed.

Supply and fixing in repairs stop cock (ISI marked) of cast copper alloy fancy type chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions 15 mm bore, complete all as specified.

Supply and fixing in repairs 15mm bore pillar tap cast copper alloy with capstan head, fancy type, chromium plated, screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed for iron pipe fixed in repair complete, all as specified & directed

Supply and fixing in repairs bib taps 15mm bore of cast copper alloy fancy type, screwed down, high presure with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule, fixed in repair, complete all as specified and directed.

Supply and fixing in repair chromium plated shower roses with or without swivel joints 125mm size including fixing to steel pipe or union, complete all as specified and directed.

Supply and fixing in repairs stop valve of cast copper alloy chromium plated with long shank concealed type screwed down high pressure screwed both ends for iron pipe or for unions 15 mm bore, complete all as specified.

Supply and fixing Stainless steel sink 1mm thick for kitchen wih plugs, washers and wastes including fixing bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mmx460mm bowl size 410mmx330mmx160mm fixed, complete all as specified.

Supply and fixing in repairs stainless steel kitchen plate rack of size 915 x 915 x 225 mm dia (ISI Marked) all as specified.

Supply and fixing Waste coupling of PTMT (half or full threaded) (Minimum weight 45gms) for 32mm bore dia of discharge pipe to WHB, sink, complete all as specified.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick masonry, complete all as specified.

Fixing only old steel water tubing of 15mm bore and connections in new or old position fixed to walls, ceilings and floors etc. including fittings as required, complete all as specified.

M&L Steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings fixed to walls and ceilings or laid in floors, complete all as specified.

Fixing only old steel water tubing of 20mm bore and connections in new or old position fixed to walls, ceilings and floors etc. including fittings as required, complete all as specified.

M&L Steel water tubing of 20 mm bore ‘medium grade’ galvanized with all fittings fixed to walls and ceilings or laid in floors, complete all as specified.

M&L 10mm thick rendering in cement mortar 1:3 on facia or edges of chajjas, ceiling and roof projections etc including taking out pealed off plaster/concrete and making the line in true shape & finishing the surface even and smooth without using extra cement, complete all as specified.

Demolition of brick tile or terracing tiles, single layer on roof including mud phuska complete all as specified.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust including 20 mm thick screeding in cement mortar 1:4 mixed with water proofing compound @ 3% by weight of cement & finishing the surface even and smooth without using extra cement complete all as specified (WPC shall be measured and piad separetely)

Supply only liquid water proofing compound, complete all as specified.

M& L applying water proofing membrane APP (Atactic Polyprobhlene Polymer) modified membrane with non-woven polyster reinforcement/mat with thermal insulation of weight not less than 3.6 kg/sqm and thickness not less than 3 mm, laid by torch application method with overlap 100 mm on length side and 150 mm on the width side over a solvent based bitumen primer @ 0.3 Ltr Sqm by the same manufacturer conforming to IS:3384-1986 on prepared surfaces complete all as specified and directed

M & L PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in padding of average thickness 40mm, and finishing the surfaces even & fair without using extra cement, complete all as specified and directed.

M & L preparation of newly plastered or unplastered surfaces of wall /facia/Chajjas etc of any description over 10cm width or girth not otherwise described and applying two coat of weather proof exterior emulsion paint over a coat of primer complete all as specified

M & L preparation of old plastered or unplastered surfaces of wall /facia/Chajjas etc of any description over 10cm width or girth not otherwise described and applying two coat of weather proof exterior emulsion paint over a coat of primer complete all as specified

S & F Coloured chequered cement concrete tiles 300x300x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment laid over and including 75 mm thick PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) and 15mm thick screed bed in cement mortar 1:4,complete all as specified and directed.

Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specified and directed.

M&L Point wiring for light/fan controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings, including 1.5sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green) (b) On RCC roof ceiling PVC conduit shall be provided on surface for fan with proper fixing clips all as directed.

All as per above item no 89 here in before but for one 3 pin socket outlet 5 amp on independent board all as specified and directed.

All as per above item no 89 here in before but for one 3 pin socket outlet 5 amp on same board all as specified and directed.

All as per above item no 89 here in before but for one bell/buzzers point controlled by one bell push button all as specified and directed.

M&L Point wiring with 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings on independent board including 2.5sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green)

S & F modular metal flush box with white cover plate with frame 1-2 module complete all as specified and directed.

S & F modular metal flush box with white cover plate with frame 3 module complete all as specified and directed.

S & F modular metal flush box with white cover plate with frame 4 module complete all as specified and directed.

S & F modular metal flush box with white cover plate with frame 6 module complete all as specified and directed.

S & F modular metal flush box with white cover plate with frame 8 module complete all as specified and directed.

M&L modular switch 1 way 6A, 1 module, complete all as specifed.

M&L modular switch 1 way 16A, 1 module, complete all as specifed.

M&L modular socket 6A- 2/3 pin combine 2 module, complete all as specifed.

M&L modular socket 6A/16A- 2/3 pin combine 2 module, complete all as specifed.

M&L modular push bell switch 1 way 6A, 1 module, complete all as specifed.

M&L modular blank plate, 1 module, complete all as specifed.

M&L Ceiling rose, 3 phase/bakelite 65x50mm two or three therminals isolated body fixed on PVC round block complete all as specified.

M & L bell multi music type 230 volts AC supply all as specified and directed by Engineer-in-Charge.

S&F modular fan step regulator, 120 W- 2 module for ceiling fan 1200/1400 mm sweep complete all as specified.

M&L Lamp holder PVC/Polycarbonate type with back plate having matching colour to holder for angle/batten fittings complete all as specified and directed.

S & F LED Tube light fitting 20 watt , 230 volts,box type complete with bipin holders,connector block and retro LED rod of 20 Watt, 4 feet long with aluminium housing provided for efficient heat dissipation with polycarbonate diffuser having high efficacy (double side connection) complete with all accessories internally prewired batten (double side connection) and including making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceilling rose/PVC connector to light fittings ,complete all as specified and directed. Note: (i) Contractor shall produce LM 79 & LM 80 test report form OEM owned NABL accredited laboraory. (ii) Contractor shall give gurantee of complete fitting/ fixtures for minimum of 2 years form the date of completion. (iii) Contractor shall conduct the inspection of company representative at site before installation of fittings/fixtures at no extra cost. (iv) Contractor shall arrange arrange 70% material at site for approval of GE before incorporation in the work.

S&F in replacement LED ceiling light fittings flush Mount ceiling light fixtures including (BL 20 W Round LED down light), lamp holder etc connecting electricaly to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm complete all as specified and directed.

S&F in replacement LED bulkhead fitting luminaries with opla diffuser including (LED lamp type 10 watt LED 6000 K), lamp holder etc connecting electricaly to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm all as required complete all as specified and directed.

S&F sheet metal enclosure factory made (Double door) TPN DB 4 way vertical type, IP 43, IK 09 having provision for one number incoming MCCB 4 pole and 12 Nos ougoing MCB SP, with 200Amps rated copper bus bar, neutral link, earth bar and din rail fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified. Note: MCCB and MCB shall be measured and paid separately

S&F MCCB 4 pole 63 Amp, 415 V with 16KA breaking capacity with spreader links 4 nos and making connection with cable and bus bar in MCB DB complete all as specified and directed.

Supply & Fix ceiling fan AC single phase 230/240 volts of size 1200 mm sweep complete type BEE 5 star rated 210 CMM air delivery including accessories blade set ,down rod, copper wound fan motor , canopy set, shackle kit etc including connecting to ceiling rose with 3 core 0.5 sqmm flexible copper wire all as required or directed . Note: Test report and Warranty certificate from OEM for minimum 2 years to be submitted before claiming for payment.

Supply & Fix Exhaust fan AC sinlge phase 230/240 volts of size 300 mm sweep, 1350 RPM , power consumption not more than 70 watt including accessories blade set ,MS frame, copper wound fan motor , louver set, 4 nos 10 x 75 mm long fastners to fixed the same with existing wall including connecting to ceiling rose with 3 core 0.5 sqmm flexible copper wire all as required or directed.

S&F Geyser 25 Ltrs capacity, 230 volts, vertical type , BEE with 5 star rated , SS tank, adjustable knob from 25 degree celcius to 75 degree celcius for vertical mounting bracket, heating element 2 KW, thermostat, ELCB water tubes, fasteners, drain pipe and other standard accessories and safety devices as per manufacturer' s catalouge incl necessay drilling, provn of anchor bolts of suitable size and making electrical connections complete all as directed by Engr-in-charge. Make: Model "monza-ec" of Havells or equivalent models of Bajaj/ Racold/ Usha Lexus/ Voltas

M&L Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 50 Hz, 8 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified.

M&L MCB DP 20 to 32 Amp, 240V with 10KA breaking capacity of 'C' series in distribution boards all as specified and directed.

M&L MCB SP 6 to 20 Amp, 240V with 10KA breaking capacity of 'C' series in distribution boards all as specified and directed.

Supply and laying in repairs of existing circuit/submain wiring alongwith two single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of size 10 sqmm drawing into and including concealed PVC rigid non metallic conduit of 25mm dia and single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of 10 sq mm as earth wire including cutting chases in brick wall, rendering in cement mortar 1:4 and making good the disturbed surfaces to match existing complete all as specified & directed. Note: Two runs of 10 Sqmm single core PVC insulated copper conductor cable(FRLS) and one run of 10 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of 25mm dia wiil be measured as a one unit.

Supply and laying in repairs of existing circuit/submain wiring alongwith two single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of size 4 sqmm drawing into and including concealed PVC rigid non metallic conduit of 25mm dia and single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of 4 sq mm as earth wire including cutting chases in brick wall, rendering in cement mortar 1:4 and making good the disturbed surfaces to match existing complete all as specified & directed. Note: Two runs of 4 Sqmm single core PVC insulated copper conductor cable(FRLS) and one run of 4 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of 25mm dia wiil be measured as a one unit.

Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to galvanized earh lead wire of size 4.0 mm by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3 of SSR Part I, wire protected by dia 15 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI medium grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified. Note: The rate quoted include cost of 7.5 metre earthing wire with protection pipe.

Supply laying jointing and testing LT XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sqmm 3.5 core complete all as specified. Note : Earth work , sand cushioning, GI pipe , brick covering for mechanical protection will be measured and paid separately under respective item of Schedule.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for foundation laying poles, stay assembly and laying of LT/HT cables in any type of soil and getting out, complete all as specified.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, in any type of soil, complete all as specified and as directed.

Removal of excavated material (soil) to a distance not exc 50m and depositing where directed at a level not exceeding 1.5mtr above starting point complete all as specified and directed

S&F DWC high density polyethelene pipes in replacement having 63/50outer dia mm, inner as per site requirement having corrugation on the wall and plain surface on the inner wall conforming to IS: 14930(Part I & II) for protection of underground cable laid along pole/along wall/in PCC on GL/roof and including all fittings as required at site including aking down the old unserviceable complete all as specified and directed. Make -Trupati /Equivalent

M & L GI pipe medium grade 50 mm bore with all fittings for cable protection fixed to walls/ poles or laid in trenches, under road/ under culvert/ under path/ under floor /on wall etc with fixing clamps, nuts bolts etc all as specified.

Notes : The Schedule of Credit amount shall be deducted from the total of this schedule(BoQ) to arrive at Contract Sum.

Ms International Engineers

Standard engineers

Neeraj Enterprises