SPECIAL REPAIR OF LT PANEL AND WIRING AT CERTAIN E/M INSTALLATION AND SPL REPAIR TO TOILET BLOCK NO 38 AT AEC TRG COLLEGE AND CENTRE PACHMARHIAT AEC RECORDS, PACHMARHI.

Amount

M&L for earthing complete with galvanized steel earth plate 600x600x6 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvanised iron strip 32x6 mm dia as earthing lead by means of bolts, nuts, check-nuts, and washers of galvanised iron or steel besides welding at all joints as shown in drawings and including excavation and earth work, GI pipe medium grade 40 mm bore for protection of GI strip from earth electrode to machinary/panel/pole, supplying and laying charcoal stone aggregate) chamber and RCC cover of size 54cmx54cmx50 mm (1:2:4) type B1 using 20 mm graded crushed stone aggregate reinforced with 8 mm dia TMT bars @ 75mm C/C both ways with mild steel handle 12 mm dia, PGI funnel with wire mesh, 20 mm dia GI pipe light grade for watering all as shown in drawing including taking out the old one Note - Cost of GI stripand GI protection pipe up to a distance 7.5 M shall be included in quated rate of above Items complete all as specified and directed

Taking down existing unserviceable/old point wiring surface /batten excluding fitting fixtures ,ceiling roses, pendant/angle holders, regulators, sockets,switches but including/excluding PVC conduit complete all as specified and directed

Material and labour for point wiring ,using approved colour coding (Phase-red,Neutral-black,Earth-green) complete with FRLS PVC insulated and unshealthed stranded copper conductor cable 1.5 sqmm single core conforming to IS 694 including medium duty concealed unplasticised PVC conduit conforming to IS 9537(part-3) and ISI marked not less than 20 mm dia with concealed in wall pressed steel terminal box of not less than 2 mm thick of required size including painting terminal boxs inside and outside with two coat of synthetic enamle paint over one coat of red oxide primer with top cover 3 mm thick bakelite laminated sheet with brass screws and Cup washer with all assessories including FRLS PVC insulated and unshealthed stranded copper conductor cable 1.5 sqmm single core in green colour as earth wire connected to earth dolly complete all as specified and directed .

(a)One light/fan/exhaust fan point controlled by 1 No,one way 5/6 Amp switch.

(b)One 3 pin /5 pin socket outlet 5 Amp controlled by 1 No one way 5/6 Amp switch on same board along with other switches ,fan regulator etc.

(c)One 3 pin /5 pin socket outlet 5 Amp controlled by 1 No one way 5/6 Amp switch on independent board.

S&F switch piano flush button single pole one way 6 Amp, 240 Volts conforming to IS 3854 ISI marked.

S&F for socket outlet, 5 Pin, 6 Amp flush type conforming to IS 1293 ISI marked including .

Material and labour for point wiring ,using approved colour coding (Phase-red,Neutral-black,Earth-green) complete for one socket outlet 15 Amp on independent board with FRLS PVC insulated and unshealthed stranded copper conductor cable 4 sqmm single core conforming to IS 694 including medium duty concealed unplasticised PVC conduit conforming to IS 9537(part-3) and ISI marked not less than 20 mm dia with concealed in wall pressed steel terminal box of not less than 2 mm thick of required size including painting terminal boxs inside and outside with two coat of synthetic enamle paint over one coat of red oxide primer with top cover 3 mm thick bakelite laminated sheet with brass screws and Cup washer with all assessories including FRLS PVC insulated and unshealthed stranded copper conductor cable 4 sqmm single core in green colour as earth wire connected to earth dolly complete all as specified and directed .

S&F switch piano flush button single pole one way 15 Amp, 240 Volts conforming to IS 3854 ISI marked.

S&F for socket outlet, 3 Pin, 15 Amp flush type conforming to IS 1293 ISI marked .

S & F ceiling rose, surface Bakelite,isolated body three terminals complete all as directed.

S&F MCB’s single pole and neutal, 10 KA ,32 Amp to 40 Amp 240 Volts,and of ''B'' series including taking down old one complete all as directed.

S&F MCB’s single pole and neutal, 10 KA ,32 Amp to 40 Amp 240 Volts,and of ''B'' series including taking down old one complete all as directed.

S&F Electronic fan regulator steped type (flush type) 240 volt ,50Hz ,single phase on existing phenotic laminated sheet including taking down old one and connecting complete all as specified and directed.

S & F sub main wiring using approved colour coding (Phase-red,Neutral-black,Earth-green) complete with two single core FRLS PVC insulated and unshealthed stranded copper conductor cable 4 sqmm as current carrying conductor and one run of 4.0 sqmm as earth contunity conductor ,voltage rating 1100 volt ,ISI marked drawn in and including concealed PVC conduit ISI marked of dia not less than 25 mm and thickness 2 mm with stranded accessories along with one run of FRLS PVC green colour insulated,unshealthed,stranded copper conductor of size 4 sqmm including taking down old one all as specified and directed Note: Two run of single core FRLS PVC cable with one run of earth contunity conductor and conduit shall be measured as one unit.

S&F sheet metal enclosures (MCB Distribution board) when MCB’s to be used single pole and neutral 8 ways 220 volt with 200 amps rated bus bar, double door with bus bar neutral link earth bar, Din rail, necessary blanking plated, including fixing DB flush in wall complete with making good disturbed surfaces as per existing including taking down old one specified and directed .

Demolition of cement concrete in ground floor and paving n.exc 15 cm thick below or above ground level complete all as specified and directed .

Dismantling floor, hearth or wall tilling incl cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L 75 mm thick PCC 1:4:8 type D2 using 40 mm graded aggregate as in sub base complete all as specified and directed.

M&L 25mm th PCC 1:2:4 type B-0 using 12.5mm graded aggregate as in flooring, finished fair and even complete all as specified and directed.

M&L non-skid white ceremic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set & jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:4) complete all as specfied and directed.

M&L glazed ceremic tiles in vertical surfaces 450x350x7mm thick, set & jointed in neat cement slurry and pointed in white or coloured cement to match tiles laid over and including 10 mm thick rendering in CM (1:4) complete all as specfied and directed.

M & L rendering 10mm thick on brick wall or concrete surface in cement mortar 1:4 finished fair and even complete all as specified and directed .

M & L rendering 10mm thick on other than fair face of brickwork or concrete surfaces in cement mortar 1:4 complete all as specified and directed .

Supply only liquid water proofing compound complete all as specified and directed .

M & L 75mm th PCC 1:3:6 type C-2 using 20mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement, with and incl joint filling (size 30mm deep x 10mm wide) with sealing compoiund grade-A at 3m interwal and corner complete all as specified and directed.

M&L applying two coats of cement based paint on new/ old or undecorated wall surface including preparation of surfaces after removal of existing treatment, complete all as specified and directed.

M&L applying two coats of white wash on new/old decorated or undecorated wall surfaces including preperation of surfaces complete all as specified and directed.

S&F in repair vitreous china water closet squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rests, incl connection to trap & to flushing pipe, anti syphonage pipe etc. exluding flushing cistern and making good to floor complete all as specified and directed.

S&F in repairs 10 ltrs capacity (PVC), valve less, syphonic action type, fluhsing cistern, low level, white, with inlet, ball valve, float and handle including brackets and 32 mm flush pipe, complete all as specified and directed.

S&F in repair centre hole vitreous china,white, padestal suitable for wash hand basin, flat back size 550x400mm complete all as specified and directed.

Supply only 32mm dia waste pipe of polythelene,flexible, for wash hand basin or kitchen sink complete all as specified and directed .

S&F in repair vitreous china bowl urinal flat back size 465x355x265mm, white with grating, union for discharge pipe on bracket excluding flushing cistern flush pipe complete and all as specified and directed.

S&F vitreous china urinal partition white of size 310x700mm complete all as specified and directed.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia (min wt 60 gms) complete all as specified and directed .

Supply only PVC connection 15x450mm size complete all as specified and directed .

S&F in repair 20mm dia brass chromium plated tubular towel rails, D type, 60 cm long between flanges,complete all as specified and directed .

Cutting chases, pinning in , for concealed water tubing on brick walls, making good to facing where required and pointing in cement mortar 1:3, not exc 10 cm girth complete all as specified and directed .

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 15 mm bore GI tubing complete all as specified and directed .

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 15 mm bore GI tubing complete all as specified and directed .

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 20 mm bore GI tubing complete all as specified and directed .

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 20 mm bore GI tubing complete all as specified and directed .

S&F rotational moulded polyethylene water storage tank, double layer construction, ISI mark (cylindrical vertical with closed top) hoisted and fixed in position with and including 20 mm dia GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings, of 1000 ltr Capacity of tank complete all as specified and as directed.

S&F ball brass valve, with polythelene float and fly nut complete screwed down for iron pipe of 20 mm dia complete all as specified and as directed.

S&Fin repair gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 20 mm dia complete all as specified and as directed.

S&F in repair 15 mm dia bib tap cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repair stop valve, cast copper alloy, fancy type,chromium plated with long shank and cup (Concealed type), screwed down both ends for high pressure, as per ISI suitable for 15mm dia iron pipe complete all as specified and as directed.

S&F angle valve, cast copper alloy, fancy type,chromium plated with long shank and cup, screwed down both ends for high pressure, as per ISI suitable for 15mm dia iron pipe complete all as specified and as directed.

S&F Swivel shower of PTMT any colour for fixing with 15mm pipe (Min wt 40 gms) incl shower arm 15mm size, 195mm long with bend of 45 degree with flange of PTMT any colour (min wt 40 gms) complete all as specified and as directed.

Taking down chowkhat with shutter (without taking of shutter from the frame) exc1.5 & n exc 4 sqm each complete all as specified and as directed.

Taking down chowkhat with shutter (without taking of shutter from the frame) n exc1.5 mtr each complete all as specified and as directed.

S&F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes, as per specifications and drawing complete all as specified and as directed.

S&F 30mm thick factory made moulded solid panel prelam PVC shutter consisting of frame made out of MS tube of 19 guage thickness and size of 40mm x 20mm for stiles, top lock and bottom rails MS frame shall be covered by heat moulded PVC 'C' Channel of size 30 x 100mm forming styles and 5mm thick prelam 125mm wide PVC sheet for top, lock nrail and bottom rail on either side of panel. Paneling of 10mm prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with 30mm wide x 5mm thick prelam PVC sheet beading on either side. An additional 5mm thick prekam PVC sheet strip of 20mm width is to be struck on the interior side of 'C' Channel nusinjg PVC cement solvent.

S&F steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars dovetailed or welded complete all as specified and directed.

M & L preparing surface of wood and wood based material and steel and iron work of any description and girth and treating ends of post, back of chowkats etc, area exc. 0.1 sqm and n.exc. 0.5sqm, with tar or coal tar or black paint complete all as specified and directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet,cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as directed.

S&F 125 mm size MS butt hinges medium weight cold rolled fixed/ welded to frame complete all as specified and directed.

S&F125 mm long,aluminium,anodised, barrel tower bolts of extruded section all as specified and directed.

S&F 125 mm size aluminium handles,cast type,anodised all as all as specified and directed.

S&F Mild Steel bands,straps, supports or stays for rainwater pipes, soil/waste or vent pipes including bolts, if required, hold fast and similar small articles conforming to Fe 290 Gde E-165 complete all as all as specified and directed.

S&F sheet pin headed glass ordinary quality 3mm thick and glazing with oil putty in squares n.exc. 0 .5 sqm each pane complete all as specified and directed..

M&L applying two coats of synthetic enamel paint over a coat of red oxide (primer) on new steel surfaces of any description over 10 cm width or girth including preparation of surfaces, complete all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed.

S&F 110mm PVC (SWR) bends with access door any radius complete all as specified and directed.

S&F 110mm PVC (SWR) junction double, (double T) with access door any radius complete all as specified and directed.

S&F 110mm PVC (SWR) vent cowl complete all as specified and directed.

S&F 110mm bore PVC (SWR) 'P' trap, including fixed with solvent cement complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75mm PVC(SWR) bends with access door any radius complete all as specified and directed.

S&F 75mm PVC(SWR) vent cowl complete all as specified and directed.

M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

SUNIL ENTERPRISE

M/S Shanti Enterprises