CERTAIN SPECIAL REPAIR OF BLDG NO T-68 AT SAHAPUR CAMPS AND SPECIAL UNDER GE(C) KOLKATA

Amount

NOTES :(i)The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates. (ii) It is highlighted that the cretin condition of General Condition Of Contracts (IAFW-2249) has been modified as direction of MOD i.e inclusion of performance security, deletion of risk & cost provisions and increase in defects liability period all as specified in tender document. The tenderers should keep in mind while quoting their offer SCHEDULE 'A' PART - I FOR B/R PORTION (Sl No 02 to 100 )

Dismantling corrugated AC sheeting in roof covering including ridges complete all as specified & as directed.

Dismantling plain/corrugated steel sheeting, any guage, thickness including eves gutter / rain water pipe complete & removal all as specified

Dismantling steel work including gates, rafter, purlin, roof truss etc complete all as specified & as directed.

Dismantling timber scantling 40 Sqcm and over in section, in any position (Unframed work) complete all as specified & as directed.

Dismantling fillets, rails, posts, rafters, purlins etc under 40 Sqcm in section (unframed work) complete all as specified & as directed.

Material & labour of MS rolled sections as in in roof truss (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) and fixed with angle cleats, Fe-410-W(Gde-E 250) Quality Acomplete all as specified and as directed. Note:- The drawing of truss shall be approved by the GE prior to incorporation in the work.

Material & labour of Mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-290(Gde E-165) complete all as specified and as directed.

Material & labour of Mild steel screw bolts (machine made) with hexagonal or square head one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 10 cm and not exc 15 cm long, dia of neck 11 to 15 mm complete all as specified and as directed.

Supply and fixing of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick and pitch length 75 mm c/c of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Supply and fixing of pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridges, tips, valley, gutters, length & girth as fixed with nail or screws complete all as specified and as directed.

Material, labour and fixed of power coated aluminium snap grid frame work for false ceiling, size of grid 605 x 605 mm, including aluminium main/closs tee of size 35mm x 23mm x 1.5 mm ( minimum) aluminum BULBED TEES section and aluminium angle of 25mm X25mm X1.5mm thick, sutiable type GI wire hanging arrangement with adjuster all as specified in clause no 10.38 in SSR part-I and including 6 mm thick high pressure steam cured non asbestos fibre cement designer board as per IS 14862 with applying of two coats of acrylic distemper over a coat of primer including taking dwon existing false ceiling system complete all as specified and directed. Make (i) ALUMINUM SNAP GRID:- HINDALCO/ INDALCO/ JINDAL (ii) Non Asbestos Fibre Cement Board as per IS 14862:-ARMSTRONG/ SAINT GOBAIN (GYPROC)/EVEREST / VISAKA Industries Ltd

Material and labour for mild steel work as in 40 mm dia MS pipe medium grade for hanging false ceiling , clamps etc conforming to Fe-290 Gde E-165 and making good the disturbed surfaces all as directed by Engineer-in-Charge.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Material and labour for fly ash Brick work with bricks class designation 75, old size, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

Material and labour for old servicable brick work with bricks straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 completes as and specified and directed. Note:-The brick shall be re-used obtained from demolition of brick work at relevant items of BOQ.

Material and labour for fly ash brick work with bricks class designation 75, size as per old size brick, straight or curved on plan exceeding 6 m mean radius half brick thick walls built in Cement Mortar 1:4 complete all as specified and as directed.

Taking down cement plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. and removal outside of MOD land complete all as specified and as directed.

Rendering 15 mm in Cement Mortar 1:6 on fair faces of brick work or concrete surfaces finished even smooth without using extra cement to the plastered surface complete all as specified and as directed.

Material and labour for Rendering 15mm thick plaster in Cement Mortar (1:4) on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement, with water proofing treatment. Note:- Water proofing compound shall be measure and paid separately

Supply only integral liquid water proofing compound

Material and labour for Preparation of new wall surface and applying two coats of acrylic washable distemper over a coat of primer complete all as specified and directed.

Material and labour for complete removal of existing finishing of internal wall surface of building/structure by mechanical appliance and preparation of old surfaces and applying two coats of acrylic washable distemper over a coat of primer complete all as specified and directed.

Material and labour for complete removal of existing treatment of external wall surface of building/structure by mechanical appliance and preparation of old surfaces and applying two coats of acrylic exterior weather resistant paint(weather proof paint) over a coat of acrylic primer as spcefid in clause No 17.17 of SSR Part-I 2009 complete all as specified and directed.

Material and labour for preparation of new wall surfaces and applying two coats of acrylic exterior weather resistant paint(weather proof paint) over a coat of acrylic primer as spcefid in clause No 17.17 of SSR Part-I 2009 complete all as specified and directed.

Material and labour for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel and iron surfaces of any description over exceeding 10 cm in width or girth complete all as specified and as directed..

Painting 2 coats of synthetic enamel paint on steel and iron surfaces of any description not exceeding 10 cm width or girth when unconnected with other painting or when painted in different tint including preparation and one coat of red oxide primer

Material and labour for reinforced Cement Concrete M-20 (Nominal mix) using 20 mm graded stone aggregate as in beam, lintel beam over 1.50m span complete all as specified and directed.

Use and waste of formwork to sides and soffits of lintels, beams and the likes and similar work with rough finished surfaces complete all as spd and directed.

Taking down chowkats/frames with shutters (without taking off shutters from the frame) etc. exceeding 1.50 Sqm but not exceeding 4.00 Sqm each complete all as specified and as directed.

Taking down chowkats/frames with shutters (without taking off shutters from the frame) etc. not exceeding 1.50 Sqm each complete all as specified and as directed.

Supply and fixing of pressed steel door frames (fabricated out of CRLCS sheet 1.6 mm thickness) 100x45 mm size with one or more rebates including necessary fixing lugs, hinges, lock striking plate etc. complete all as specified and as directed.

Supply and fixing of pressed steel door frames (fabricated out of CRLCS sheet 1.6 mm thickness) 125 x 60 mm size with one or more rebates including necessary fixing lugs, hinges, lock striking plate etc. complete all as specified and as directed.

Material & labour of high strength steel Fe-500 TMT bars 8mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as spd and directed

Supply and fixing of 30 mm thick flush shutters, solid core construction, with block board core and comercial plywood face panels with one face is covered with decorative face veneer with lipping/frame to match all complete all as specified and as directed.

Material and labour for Factory made partly glazed i.e. Upper panel will be wire mess panes fitted externally in the clear space & lower panel will be both Side prelam PVC sheet of PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

Material and labour for Solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with Mild Steel square tube, suppling & fixing in opening as per drawing complete all as specified and directed.

Material and labour for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawingcomplete all as specified and directed.

Material and labour for power coated aluminium casement window and ventilator shutters, side hung type without sash bars, side hung type without sash bars, aluminium sections weighing 0.55 Kg/m (minimum) and thickness of member/section not less than 1.50 mm including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150 mm long (1 No.), hinges type B-21 100 mm long (2 Nos.) suitable handle (1 No.) complete all as specified and as directed.

Material & labour of power coated aluminium , three track sliding window with three nos shutters made of aluminium section as per drawing no CWE/KOL/TD-33 of section no 1F-1F including necessary jointing cleats, glazing clips, rubber neoprene packing, roller, locking arrangement, handles 2 Nos , anodised aluminium snap beading screws etc. Complete all as specified. Complete all as specified and as directed. Note Nos :- (i) All window member including fitting & fixture i.e frame, track, shutter frame, etc shall be deem to included quoted rate. Only measure opening size of window. (ii) Only Glass for window & wire mesh shall be measure and paid separately under relevant items of BOQ .

Material and labour for PCC 1:2:4 type B-1 using 20mm graded crushed aggregate as in filling in holdfast/ filling in pressed steel frame etc including necessary form work complete all as specified and directed.

Materials and labour for Mild Steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290(Gde E-165) including taking dwon old one complete all as specified and as directed.

Material and labour for Stainless steel wire cloth, 0.43 mm nominal dia of wire and avergae width of aperture 1.00 mm and fixed with stainless steel wire staples complete all as specified and directed.

Material and labour for Butt hinges Stainless steel 100 mm size complete all as specified and directed.

Material and labour for Aluminium anodised barrel tower bolts of extruded section size 200 mm complete all as specified and directed.

Material and labour for Aluminium anodised sliding door bolt, with hasp & staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections 300 mm long .complete all as specified and as directed.

Supply and fixing of end finials for drapery rod and including closed type stainless steel all brackets fixed on wall complete all as specified and directed. Make: SOFFIO-II model of VISTA or equivalent model of NOVA

Material and labour for drapery rod made of electric resistance welded MS pipe of 21mm dia having a coating of corrugated virgin PVC extrusion and cover with ABS plastic complete all as specified and directed. Make: SOFFIO-II model of VISTA or equivalent model of NOVA

Material and labour for Aluminium handles cast type anodised 150 mm size complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors, sunken floor and paving complete all as specified

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to stores and rubbish off the MOD premises complete all as specified and as directed.

Material and labour for 75 mm thick plain cement concrete M-10(Nominal Mix) using 20 mm graded stone aggregate as in plinth protection, finished even and smooth without using extra cement complete all as specified and as directed.

Material & Labour Non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular area of each tile exceeding 0.11 Sqm and not exceeding 0.18Sqm , in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed layer in CM (1:4) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

All as per item No _55 here-in-before but to vertical surfaces such as skirting over and including 10mm thick rendering in CM (1:3) complete

Material & Labour Glazed ceramic tiles 400x300x7 mm(Coloured) on vertical surfaces such as skirting, dados and riser to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match complete over 10mm thick screed bed vertical layer in CM (1:4)all as specified and as directed.

Material & Labour of 18mm thick granite ( of any type) work ( table rubbed and polished in pillars and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust admixture of pigment to match with shade of granite over 15mm thick screed bed layer in CM (1:4) including taking down existing one complete all as specified and as directed.

Supply and fixing of 15mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors and including taking up old GI pipe complete all as specified and as directed.

Supply and fixing of 20mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors and including taking up old GI pipe complete all as specified and as directed. Note for item no 57 & 58:- All fitting & fixture such as Bends, Elbows, Tees, Short Pieces, Connectors, Back - Nuts Caps, Plugs, Unions, Flange (core) & flange (ring), reduction Tee, reducing socket, Male & female threaded socket, tank connector, holding clamp shall be provide as per site requiredment as as directed by AGE and same shall deem to be included in quoted rate.

Supply and fixing in repair of bib cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no PIS -08 of Prayag or equivalent model of make list as given in PS as approved by GE.

Supply and fixing in repair of chromium plated pillar cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no PIS 02 of Prayag or equivalent model of make list as given in PS as approved by GE.

Supply and fixing in repair of stop cock , concealed type cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no PIS -18 of Prayag or equivalent model of make list as given in PS as approved by GE.

Supply and fixing in repair of stainless steeel of 304 grade of kitchen sink with drain board of overall size 915mmx460mm and bowl size 410mm x330mmx160mm depth or equivalent made of 1mm thick stainless steel sheet with 32mm bore CP waste coupling including ball and chain 300mm long with bass cap rubber plug, 32mm bore PVC waste pipe (heavy duty) 90cm long, and bedded in cement mortar and fixed in CP cantilever brackets. Make: Cat No. 1239D of PRAYAG or equivalent make as per PS

Supply and fixing in repair of 125 mm dia of shower rose with 225 mm long arms, cast copper alloy chromium plated , swivel joints and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no BS-76 of PRAYAG or equivalent model of make list as given in PS as approved by GE.

Supply and fixing in repair of chromium plated brass corner glass shelf fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified. Make :- Cat no BEA-44 of Prayag or equivalent model of make list as given in PS as approved by GE.

Supply and fixing in repairof Towel Rail 600 mm long of chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed. Make :- Cat no BA-40 of Prayag or equivalent model of make list as given in PS as approved by GE.

Supply and fixing in repair chromium plated brass soap dish fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified. Make :- Cat no Cat no BA-05 of Prayag or equivalent model of make list as given in PS as approved by GE.

Supply and fixing in repair of PVC cabinet size 350x450mm with looking mirror complete all as specified and as directed by Engineer-in-charge. Make: Cat No.557 of PRAYAG or equivalent make as per PS

Supply and fixing of Vitreous china squatting pan, 'Orissa' pattern, size 580x440 mm white with including CI ‘P’ or ‘S’ trap & integral foot rests fixed in cement concrete and including taking down existing one complete all as specified and as directed Make: CALINA S3010102 & S9030101 of CERA or equivalent model of make list as given in PS as approved by GE.

Supply and fixing as in repair of PVC low level flusing cistern 10 litres capacity white with ball valve & brackets with flush pipe complete all as specified and as directed. Make: CHIVAS of CERA or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of vitreous china wash basin white flat back, size 550 x 400 mm including CP waste coupling,with GI pipe brackets & , rag bolt in cement concrete/brick wall and including taking down existing HWB and making good wall surface complete all as specified and as directed. Make: Cat no S2040103 wash basin of CERA or equivalent model of make list as given in PS as approved by GE.

Supply and fixing in repair of chromium plated waste coupling with wast pipe complete all as specified.

Supply and fixing as in repair of PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

Supplying, hoisted and fixed in position of rotational moulded polyethylene water storage tanks in double layers and cylindrical vertical type with manhole lids(closed top) of 500 litres capacity with ISI marked and all as specified in IS 12701 and including taking down existing water tank complete all as specified and directed .

Supply and fixing of uPVC of type-B for use in soil and waste discharge systems, single socket, 110 mm bore in any length including rubber ring joints and fixed to walls with clips and other standard material and including taking dwon old rain water pipe & removal from site all as specified in IS 13592 complete all as specified and directed.

All as per item no 75 above but double socket, 110 mm bore complete all as specified and directed.

Supply and fixing of Unplasticized (uPVC )bend for 110 mm bore uPVC pipe complete all as specified and directed.

Supply and fixing of Unplasticized (uPVC )juction equal or unequal for 110 mm bore uPVC pipe complete all as specified and directed.

Material and labour for pre-polished chequered Cement Concrete tiles of 25 mm minimum thick, size of (square/ rectangular) area of each tile exceeding 0.09 Sqm but not exceeding 0.16 Sqm double layer machine pressed set ( as per IS 1237-2012), jointed and pointed in neat cement slurry in floors and cut & polished in white or coloured cement to match over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

Material and labour for100 mm thick plain cement concrete 15 (Nominal Mix) using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed.

Material and labour for forming jambs, etc., to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete all as specified and as directed.

Subtotal of Sch A part-I

SCHEDULE 'A' PART - II FOR B/R PORTION (Sl No 84 to 117 )

Taking down carefully unserviceable copper / aluminium point wiring (light, fan, bell socket or power) including all fittings such as switches, socket, ceiling roses , regulators and switch boxes etc complete and making good the disturbed surfaces complete all as specified and as directed.

Material and labour for point wiring with PVC insulated unsheated stranded copper conductor cable of size 1.5 sq mm in and including PVC cassing caping of required width with all necessary fittings with sunk cast iron /pressed steel terminal box of1.6mm wall thickness and 3 mm thick laminated sheet top cover for mounting switches including 1.5 sq mm PVC insulated unsheathed stranded copper conductor as earth lead and connected to common earth doly for one light / ceiling fan/exhaust fan/bell controlled by one switch complete all as specified and directed by engineer incharge.

All as per item No-86 above but for one 5 amp socket independent complete all as specified and as directed.

All as per item No-86 above but 3 pin 5 amps socket out let point and 5 amps light point with the same board with other suitable complete all as specified and as directed.

Material and labour for point wiring with 2.5 Sq. mm (nominal area) PVC insulated and unsheathed single core FRLSH copper cable 1100 volts grade with multi-stranded copper conductor in and including double lock casing caping and accessories alongwith continuous earth wire 2.5 Sq mm PVC insulated and unsheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly, with and including 1.6 mm thick cadmium plated sunk MS pressed steel terminal boxes with 3 mm thick plastic laminated sheet cover fixed with brass screws complete for one socket outlet 6pin15/16 amps on independent board complete all as specified and directed.

Supply and fixing of switch piano flush single pole one way 5 amps complete all as specified and as directed.

Supply and fixing socket out let 3 pin 5 Amps flush type complete all as specified and as directed.

Supply and fixing switch socket outlet multipurpose 3 pin 15 Amps /5 Amps controlled by one switch.

Supply and fixing of switch socket outlet 3 pin 6 Amps 230 volts flush type complete all as specified and as directed.

Supply and fixing ceiling rose surface bakelite 65x50mm three terminals complete all as specified and as directed.

Supply and fixing in repair call bell, ding dong AC 230 volt single pole (ding dong type).

Supply and fixing in repair bell push flush type 5 Amps complete all as specified and as directed.

Material and labour for Electronic type fan regulator step type 120 watt, 230 volt complete all as specified and as directed. Make : Code no 14502 of Anchor or equivalent model of make list as given in PS as approved by GE.

Material and labour for lamp holder insulated body with back plate for batten fittings with 10 Watt LED lamps complete all as directed

Supply and fixing of LED surface/ceiling mounting(suspended from ceiling) box type light fitting 10Watt with LED Lamp , drive and made of epoxy powder coated extruded aluminium channel housing with high quality polycarbonate opal diffuser cover & high power LED’s as light source with 110 Lumen per watt (Minimum) and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up three core1.00sq. mm copper conductor flexible wire/cable complete all as specified. Make : Model No LDL-10-CDL of Crompton or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of LED surface/ceiling mounting(suspended from ceiling) box type light fitting 20Watt with LED Lamp , drive and made of epoxy powder coated extruded aluminium channel housing with high quality polycarbonate opal diffuser cover & high power LED’s as light source with 120 Lumen per watt (Minimum) and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up three core1.00sq. mm copper conductor flexible wire/cable complete all as specified. Make : Model No CIS-305-40-57-SL-DP-NWH of Crompton or equivalent model of make list as given in PS as approved by GE.

Supply , Fixing of LED street light fitting ( Building Security light) of 30Watt with LED lamp’s & driver and made of pressure die-cast aluminum housing, IP 65/IP 66 road way luminaries with UV stabilized polycarbonate cover or toughen glass cover & high power LED’s as light source with 110 Lumen per watt and electronic driver with efficiency > 85% . The light fitting shall be fixed on wall/pole with and including 25 mm dia( or higher size as per manufacturers recommendation) light grade GI pipe (bend to shape or as per manufacturers recommendation ) bracket 1.5 mtr long complete with MS flat iron clamp (clamps shall be 40 x 5 mm MS flat) nuts, bolts & washers including painting the clamps with two coat of aluminium paint over a coat of red oxide primer and including taking up old light fitting complete all as specified and as directed Make:- Model No- LSTM-30-CDL M of Crompton Greave or equivalent model of make list as given in PS as approved by GE. Note for items no 99 to 101 : (i) Warranty of complete LED luminaries fitting shall not less than four years and Life expectancy of LED's minimum 50,000 burning hrs,. (ii)The contractor shall be submitted the LM-79 third party NABL accredited lab test report and LM-80 test certificate and LED has to be stractured in the same sequence.

Supply and fixing of sheet metal enclosure for MCBs to be used singal pole & nutral double door 8 Way 200 Amps rated busbar and including fixed with 25mm x 6 mm mild steel clamp of suitable length and including taking out old DB complete all as specified and as directed.

Supply and fixing of sheet metal enclosure for MCBs to be used singal pole & nutral double door 4 Way 200 Amps rated busbar and including fixed with 25mm x 6 mm mild steel clamp of suitable length and including taking out old DB complete all as specified and as directed.

Supply and fixing of MCB SP of rating 6 to 32 Amps 240 V complete all as specified and as directed.

Supply and fixing MCB DP 40 to 63 amps 415 volts 10KA breaking capacity.

Supply and fixing of sub main wiring with two single core 4.0sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed 1100 volts grade IS-694 marked in PVC double lock casing caping and accessories accessories including one single core 4.0 sqmm copper conductor cable FRLSH as earth wire and including taking out old sub-main wiring complete all as specified and as directed. NOTE:- (a) All runs of copper conductor and one run of conduit shall be measured as one run length.

Earthing as in repair complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below ground level connetced with earthing wire 4.0mm dia as earthing lead by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe 15 mm bore (medium grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 Mtr etc all as shown on electrical plate No. 5 of MES Schedule Part-I complete including testing on completion. On testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost.

Supply, Installation, testing & Commissioning of Stationary storage type electric water heater(Geyser) of capacity 25 Litres with inner tank coated with glass lined coating (Feroglass technology), with high density PUF insulation Shock resistant ABS Body, 4 in 1 multifunctional safety valve, energy efficient BEE 5 star rated and confirming to IS:2082(Part-1), IS 302-2-21 : 2011 other relevant BIS including fixing arrangement and suitable capacity flexible 3 core copper cable of 1.5 metre to 2 metre length necessary connection with and including one PVC Connection pipe of 600mm length for cold water,and one CP flexible Connection pipe of 600mm length for Hot water fixing on walls with and including all necessary fitting material i.e. mild steel Bolts (Bolted to be grouted ). Nuts, Washers etc all as specified and as directed. Make:- Model MONZA DX of HAVELLS or equivalent model of CROMPTON GREAVES/ JAQUAR / BAJAJ as approved by GE. Note:-Contractor shall submit manufactures test report as per ref BIS to GE before any payment.

Supply and fixing ceiling fan enery saving and fancy type 1200 mm sweep three blade, , 50 watt maximum,Air delivery 210 Cum per Mintus (minimum),, colour /white , BEE stars shall not be less than 3 as per latest notification of BEF and conform to IS 374: 2019 without regulator including hanging rod, canopy, writing the MES fan numbers with paint and including 0.75 Sqmm , 3 core PVC insulated Flexible copper cable for connection from ceiling rose to fan complete all as specified and as directed. Make: Model-Technix Plus of USHA/ ES40 of Havells or equivalent model of BAJAJ/CROMPTON GREAVES/ORIENT as approved by GE.

Supply and Fixing exhust fan 240V, 230mm sweep, 900 RPM , MS body, highly efficient heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings and conforming to IS: 2312 and including aluminium lowers and shutters fixed to wall , writing the MES fan numbers with paint and 0.75 Sqmm , 3 core PVC insulated Flexible copper cable for connection from ceiling rose to fan complete all as specified and as directed. Make: Model- Turbo DBB of USHA/ Ventilair DB of Havells or equivalent model of BAJAJ/CROMPTON GREAVES/ORIENT as approved by GE.

Supply and Fixing exhust fan 240V, 300mm sweep, 900 RPM , MS body, highly efficient heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings and conforming to IS: 2312 and including aluminium lowers and shutters fixed to wall , writing the MES fan numbers with paint and 0.75 Sqmm , 3 core PVC insulated Flexible copper cable for connection from ceiling rose to fan complete all as specified and as directed. Make: Model- Turbo Heavy Duty of USHA/ EXHD-300-6 of CROMPTON GREAVES/Turboforce of Havells or equivalent model of BAJAJ/ORIENT as approved by GE.

Supply and Fixing industrial type exhust fan 240V, 450mm sweep, 1400 RPM , MS body, highly efficient heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings and conforming to IS: 2312 and including aluminium louers and shutters fixed to wall and 0.75 Sqmm , 3 core PVC insulated Flexible copper cable for connection from ceiling rose to fan complete all as specified and as directed. Make: Model- Turbo Heavy Duty of USHA/ REVA450-4 of CROMPTON GREAVES//Turboforce of Havells or equivalent model of BAJAJ/ORIENT as approved by GE.

Supply and Fixing industrial type exhust fan 240V, 380mm sweep, 900 RPM , MS body, highly efficient heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings and conforming to IS: 2312 and including aluminium louers and shutters fixed to wall and 0.75 Sqmm , 3 core PVC insulated Flexible copper cable for connection from ceiling rose to fan complete all as specified and as directed. Make: Model- Turbo Heavy Duty of USHA//Turboforce of Havells or equivalent model of BAJAJ/CROMPTON GREAVES/ORIENT as approved by GE.

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ₹ ___________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

S. K. CONSTRUCTION SYNDICATE AND ENGINEERING CO.

PINKY CO

INDIA ELECTRICAL EQUIPMENTS