Renovation of Primary Health Sub Centre at Badam, Barkagaon, Hazaribag.

Amount

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing P.C.C.M - 150 with nominal mix of (1:2:4) in foundation with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing 75 B Brickwork in C.M (1:6) in super structure and plinth with approved quality.

Extra for Brick Work for Each consecutive floor above 1st floor including watering and scaffold.

Providing av 63mm thick R.C.C M-200 with nominal mix of (1:1.5:3) in Chajja of all type.

Providing 35 mm thick precast R.C.C.M -150 with nominal mix of (1:2:4) in shelves with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of F.M. 2.5 to 3 with 1.5 mm cement punning at top and side and 6mm cement plaster (1:4) at bottom including screening, curing and placing the slab in position (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and direction of E/l.

Providing 19 mm thick water proofing cement plaster (1:3) with clean coarse sand

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 6 mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Extra for plaster work over exterior surface for each consecutive floor above 1st floor including cost

Providing Tor steel reinforcement of 8 mm dia. Rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l.

Providing Tor steel reinforcement of 10, 12, 16 & 20 mm dia. Rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l.

Pressed steel door frame of 1.25 mm thick of requisite profile as per specification and direction of E/I Profile - B

Supplying, fitting and fixing 35 mm thick solid core type non-decorative single leaf flush shutters in doors and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Supplying, fitting and fixing 35 mm thick solid core type non-decorative double leaf flush shutters in doors and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2 mm at 100mm. centres and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40x40x6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, carriage , hoisting and taxes all complete as per building specification and direction of E/l.

Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)

Providing and fixing 30mm thick P.V.C rigid frame paneled doors shutters manufactured by M/s Raj shree or equivalent made from M.S tube of 19 gauge thickness size 19X19mm tor styles and 15X15 for top and bottom rails covered with moulded P.V.C ‘C’ channel of 5mm thick sheet and 30X50mm vide to from styles and 5mm thick and 75mm vide P.V.C sheets tor top rail, lock rail and bottom rail on either side and 5mm thick 20mm vide cross P.V.C sheet as gap insert tor top rail and bottom rail paneling of 5mm thick P.V.C sheet fitted in the M.S frame welded/sealed to the styles and rails with 5X30 mm P.V.C sheet beading on either side and joined together with solvent cement adhesive etc. complete as per manufacture specification and direction of E/I. Fixed to frames with 4 Nos M. S. powders coated but hinges (For W.C. and Bathroom shutters).

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complete

Providing and laying precast white glazed tiles in wall

Providing and applyingof plaster or paris (putty 2 mm) thick over plaster

Providing and applying putty 1 mm thick over plaster

Providing two coats of oil bound distemper of approved shade

Finishing walls with premium Acrylic smooth exterior paint

providing two coat of synthetic enamel paint of approved shade and make over old w/surface

providing primer one coat of red lead paint of approved make over new steel surface

providing two coat of painting with ready mixed paint of approved make over new steel surface

Providing and fixing on wall face UPVC rain water pipes confirming to IS 13592 type A including jointing with seal ring confirming to IS 5382 leaving 10 mm gap for thermal expension. Single socket pipe -110 mm dia

Making plinth protection work ……do……..E/I

Providing 250mm. wide brick drain in cement mortar (1:6) with av. 250mm. clear depth and 250mm. apron including cost of earthwork involved with 75 mm. ~ cement concrete (1:4:8) over one brick designation 75A flat soling in proper grade and slope at the base, the drain duly plastered in C.M.(1:3) with punning over exposed surface all complete as per building specification and direction of E/l.

Providing and fixing 18 MM thick green marble stone flooring.

Extra for providing edge moulding to 18 mm thick marble stone counter vanities etc.

Providing and laying ceramic glazed Floor tiles Sze (300x300) mm……….do………..do……E/I

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface cmplete.

Providing and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per manufacturer’s specifications & direction of Engineerin-Charge. 60mm thick C.C. paver block of M-35 grade with approved colour, design & pattern

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately

providing ms angle 50x50x6 mm th.

Labour for hoisting, placing and fixing in position R.S. joist or tee including cutting to required shape and size straightening all complete job ( but excluding the cost of joist or Tee) as per direction of E/l.

Labour for fabricating, erecting, hoisting and fixing in position structural steel work in R.S. joist, channel, Angle, Tee, flat, plate, latice member, built up compound section in column, girder, staircase or truss including cost of gusset plates, holding down bolts, anchor plates at all heights and depths, bolting, welding (machining wherever necessary) with applying a priming coat of red lead paint all complete as per approved drawing, building specification and direction of E/l.

Providing two coats of snowcem of approved shade and make over old surface including washing cleaning, and preparing the walls, scaffolding, curing and taxes all complete as per building specification and direction of E/l.

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.

Carriage of Materials.

(A) Sand av lead 5 K M

( B)Chipes av lead 15 K M

(C) Bricks av lead 8 K M

(D) Sand av lead 3 K M

Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthenware urinal of "Hindustan" " Parry" or any other approved I.S.S. make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15 mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grms. , 15 mm P.V.C. alkathene pipe 450 mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with 2 coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/l.

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.

Supplying, fitting and fixing white glazed fires clay sink of approved make with overflow arrangements supported on C.l. or R.S. painted brackets 40 mm dia C.P. brass waste with C.P. brass chain and rubber plug, 40 mm dia P.V.C. waste pipe about 750mm long with brass coupling at one end and 15 mm C.I. body brass spindle bib cock of approved quality of weight not less than 450 grms. including cutting wall and making good the same etc. all complete as per specification and direction of E/l.

Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed c.l. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l.

S/F/F brass bib cock 15 mm dia.

S/F/F Pillar cock 15 mm dia c.i. body .

prov. s/f/f connection pipe

prov. s/f/f c.p.shower125mm dia.

S/F/F G.I. Fitting

2 . TEE PLAIN

3. NIPPLE

SOCKET PLAIN

S/F/F the following item with all materials

(a) (i) Glass shelf 600x125 mm.

(b) mirror (I) 600x450mm

© (II) c.p.brass dish container.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required

5/6 amps switch

15/16 A switch

prov. s/f/f ceiling fan (1200 mm

prov. s/f/f exaust fan (230mm)

S/F/F LED bulb 15/16 watt.

S/F/F Tube light/LED batten (20/22 ) watt

ceiling fan down rod

ceiling fan rewinding with ball bearing.

Add 18 % GST (in Basic Rate must fill 12)

Add 1% Labour Cess (in Basic Rate must fill 1)

LIFE AND COMPANY

SHANKAR CONSTRUCTION

DHANANJAY KUMAR SINGH