Certain repairs to plastering works/brick work/tiling and other misc works in SASF Odianwali and Fazilka Mil Stn

Amount

Demolition of PCC in ground floors & pavings n exc 15 cm thickness (below or above ground level) (unreinforced)

Demolition of Brickwork or stone/boulder masonry, built in CM or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework & precast concrete articles

Dismantling, floor, hearth or wall tiling including CM bedding (but not backing), removing rubbish off the premises

Taking down cement or cement lime plaster, any description on brick or stone walls, etc.

Taking down wooden chowkats or frame with shutter, without taking off shutter from the frames area exc 1.5 sqm but not exc 4sqm each.

Taking down Chowkats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames)

Taking down existing steel rolling shutters of size not exc 15 Sqm with all connecting items and repair the lath, hood covers, ball bearings, helical wire spring, lock plates, bracket plates, shaft rods, guide channels of steel rolling shutters and locking arrangements, including greasing, tightening, oiling, welding etc. wherever required, complete to make in serviceable condition and applying one coat of synthetic enamel paint including preparation of old painted surfaces and refixing in the same opening complete all as specified and as directed.

S&F pressed steel frames 125x60mm thick 1.25mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified.

S&F pressed steel frames 105x60mm thick 1.25mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified.

Cement concrete 1:3:6 type C1 filling of pressed steel frame and hold fast block etc

Resecuring or easing and adjusting without taking down shutters of any description exc 1.0 sqm but n exc 2 sqm each

S & F for Flush shutters,35mm thick,solid core construction,with block board core and plywood face panels,commercial type on both sides as specified in SSR Part – I, Section – 8, clause 8.20 (a) ; supplied and fitted to chowkats complete all as specified and directed by Engineer-in-Charge.

S&F Galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples.

S&F Galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples fixe in repair

M&L Brick work with old size burnt fly ash bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 all as specified and directed by Engineer - in - Charge .

Cutting holes not exc. half brick in brick walls built in CM or cement lime mortar & stone walls built in lime mortar for inserting holdfasts & making good dismantled portion in CM(1:3) or PCC(1:2:4) Type B-1 as required

Cutting holes exc. half brick but not exc one brick in brick walls built in CM or cement lime mortar & stone walls built in lime mortar for inserting holdfasts & making good dismantled portion in CM(1:3) or PCC(1:2:4) Type B-1 as required

S&F 35mm thick glazed and skelton shutters open rebated and prepared to receive gauze etc (without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred breds for securing glass etc sizes of members of shutters as specified in SSR Pt-I Sec 8 Clause 8.20(a) in 2nd class hard wood.

S&F for stainless steel sliding door bolts 300mm long modular type with bright bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed by Engineer-in-Charge.

Supply only stainless steelbutt hinges 100mm size, medium weight complete all as specified and directed by Engineer-in-Charge.

S&F for stainless steel barrel tower bolts 300mm long with bright bolt complete all as specified and directed by Engineer-in-Charge.

M&L PCC in foundations, filling and mass-concrete type C2 (1:3:6) using 40 mm graded stone aggregate

S&F Solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reiforced with MS square tube, suppling & fixing in opening as per specification & drawing.

S&F Factory made solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 150 mm extruded aluminium alloy handles ,fabricated type.

S & F Aluminium anodised barrel tower bolt of extruded section 200mm long all as specified and directed by Engineer - in - Charge .

S&F Butt hinges 100mm size, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type B-21

S&F curtain rod decorative pattern with brackets stops & rollers complete.

S&F in repairs, steel ventilator 1.25mm thick box type (primer coated) ERW hollow 'P' section of size 60mm x 25mm single rebated comprises glazed skeleton shutter ERW Section 50mm x 20mm and 1m thick with two openable leaf consisting two Nos. of sash bars of flat iron 12mm x 3mm complete welded to frame with one vertical mullion of ERW box type 'T' section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portionin PCC (1:2:4) type B1 four Nos. for each window including follwing fittings welded to the frame shutter complete all as specified and directed by Engineer-in-Charge. (a) Hold fast 150mm long of 12mm x 3mm made to shape - 04 Nos. Per Window (b) Handle of 'Z' section 20mm x 25mm, 100mm long - 01 No. Per Leaf (c) MS Tower bolt 150mm long - 02 Nos. per Leaf (d) MS pintol hinges of size 100mm x 14mm - 02 Nos. Per Leaf (e) 'Z' section 20mm x 25mm x 100mm long stopper Per Leaf Make : M/s Tee Pee Enterprises, M/s Friends Manufacturing Co., Kotkapura, M/s AGEW Steel Mfg Pvt Ltd, Ahmedabad, Ashwini And sons, Ghaziabad, M/s Godrej & Boyce Steel Mfg, Mumbai or equivalent as approved by GE Note : Glass and painting shall be measured and paid separately under appropriate item of BoQ

S & F for framed work such as grills, cooler stand ,grating, etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work or water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed by Engineer-in-Charge.

S&F Coloured Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:4) ,pattern to be approved by GE/Engg-in-charge.

S&F Coloured Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:6) pattern to be approved by GE/Engg-in-charge.

S&F Coloured Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:6), pattern to be approved by GE/Engg-in-charge.

S&F Coloured Glazed ceramic tiles 300x200x 6mm thick, on walls etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match over 10mm thick plaster in CM(1:4) on fair face of brick or concrete surface,pattern to be approved by GE/Engg-in-charge.

S&F Coloured Glazed ceramic tiles in vertical surface 300x450mm 7-8mm thick on walls etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match over 10mm thick plaster in CM(1:4) on fair face of brick or concrete surface,pattern to be approved by GE/Engg-in-charge.

M&L for coloured Chequered cement concrerte tiles, 30cm x 30cm x 25mm thick, set jointed and pointed in neat cement slurry with white cement and pigments over 15mm thick screed bedding layer of mortar in CM 1:4, pattern as approved by GE/Engg-in-charge.sample to be checked before quoting rate. Make:-Nitco pavers & equivalent .

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete

M&L Machine cut kota stone slab flooring 18-20 mm thick over 15mm thick screed in CM(1:4) laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete

M&L for polishing old kota stone slab flooring 18-20mm thick complete all as specified and directed by Engineer-in-Charge.

M&L 75mm thick PCC type D-2, (1:4:8) using 40mm graded stone aggregate

Hardcore of Broken brick gauge n exc. 63mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface

M & L 60mm thick rubber mould with coloured cement and pigment interlocking factory made paver blocks of any size and shape conforming to IS 15658-2006, M-35 set, jointed and pointed in dry sand over 25 mm thick sand cushion,pattern as approved by GE/Engg-in-charge.sample to be checked before quoting rate.

M&L 50mm thick PCC type C-1, (1:3:6) using 20mm graded stone aggregate Finished even & smooth without using extra cement as in plinth protection (2263.30-2212.30 = 51.00 x 0.05= 2.55)

M&L continuous brick edging, with fly ash bricks of sub class ‘B’ (old size) with width equal to the depth of the brick laid dry on end vertically including sand cushioning & filling interstices with sand (Tibba sand) complete all as specified.

M&L Rendering 15mm thick on stone masonry surfaces or surface other than fair face of brickwork in CM (1:6)

M&L rough cast finish plaster with a mixture consisting of crushed stone or fine gravel aggregate mixed with coarse sand and cement in the ratio of 1:1:1 over & including 12mm thick rendering in cement mortar 1:3 on fair faces of brick masonry or concrete surfaces of walls complete all as specified & as directed. (26.80x 2/5 = 10.72)

M&L Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM (1:4) finished even & smooth (without using extra lime or cement)

M&L Rendering 10mm thick on concrete surfaces in CM (1:3) in ceiling

S&F Sheet glass 3.0mm thick, ordinary quality & glazing with oil putty in square n exc 0.5 sq.m in each pane

S&F Sheet glass 3.0mm thick, ordinary quality & glazing with oil putty in square n exc 0.5 sq.m in each pane including hacking out old broken glass (any thicknesss, size,quality or description) from metal frame inlcuding punching or drilling out old glazing pins/spring clips

Applying two coats of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of new pre primed surface.

Applying one coats of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of new or previously untreated surface including priming with red oxide

M&L two coats of synthetic enamel on wood (ordinary tint) over one coat of pink primer over 10cm width or girth incl preparation of surface.

S&F in repairs Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern & flush pipe)

Supply & fixing as in repairs vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device complete all as specified & as directed by Engineer-in-charge.

S&F in repair PVC valveless syphonic action type low level flushing cistern coloured with inlet ball valve float and handle incl bracket 10 Lit capacity Make:- slimline / Paryware

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 500 Ltrs Capacity including Dismantling old water tanks

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 1000 Ltrs Capacity including Dismantling old water tanks

S&F in repair Ball valves 20mm high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed

S&F Ball valves 20mm high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed

S&F in repairs CP Bib taps 15 mm bore, cast copper alloy with crtuch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fancy type

S&F in repairs Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste chain & plug & porcelain stopper but including brackets Waste coupling 32mm bore of PTMT (half or full threaded)

S&F CP Pillar taps 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe

S&F in repair CP Pillar taps 15 mm borefancy type, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe

S&F in repairs Stop valves chrome plated fancy type 15 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions

S&F in repairs Stop valves 15 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions

All as Item No 66 above but 20 mm bore

S&F in repair Bib tap 15mm long body of PTMT any colour high pressure screwed for iron pipe and fixed

S&F in repair Pillar taps15mm of PTMT any colour high pressure screwed for iron pipe and fixed

S&F on repair Angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed,

Taking up or down 15mm bore dia, steel tubing & connections incl cleaning for refining or removal to store.

Taking up or down for 20mm bore steel water tubing galvanised with connection complete all as specicfied.

S&F GI Tubes, `medium grade' with all fitting & fixed complete to walls & ceilings or laid in floors of 15mm bore including taking up or down steel tubing & connections

-Ditto- all as above but fixing only.

All as Item No 74 above but 20 mm bore

-Ditto- all as above but fixing only.

S&F chlorinated PVC (CPVC) pipes 20mm outer dia fixed complete to walls, ceilings or in floors etc including jointing of pipes & fittings with CPVC solvent cement. Make:- Supreme /Vectus

S&F unions 15mm. brass to connect iron to polyethylene and fixe

S&F in repairs Brass CP shower rose 15mm bore

S&F in repair CP grating suitable for 75/ 100mm bore floor trap and fixed with white cement complete all as specified and directed by Engineer-in-Charge

M & L for Preparation of newly plastered surfaces by applying two coats of interior grade wall putty and making it smooth with sand paper by mechanical method i.e, with hand electric grinder and applying two coats of oil bond distemper over one coat of primer including all as specified by mechanical method i.e, pray gun complete all as directed by GE/ Engineer-in-Charge

M&L for preparation of new plastered and unplastered surfaces of wall Applying two coats of cement base paint of approved shade/tint on new wall surface including preparation of surface

Applying two coats of white wash on new Ceiling surface including preparation of surface.

Applying two coats of white wash on old Ceiling surface including preparation of surface.

Applying two coats of cement base paint, white or tinted on old wall surface including scrappiing down old treatment and preparation of surface.

M & L for Preparation of Old plastered surfaces by removing old treatment and applying two coats of interior grade wall putty and making it smooth with sand paper by mechanical method i.e, with hand electric grinder and applying two coats of oil bond distemper over one coat of primer including all as specified by mechanical method i.e, pray gun complete all as directed by GE/Engineer-in-Charge

M&L for complete removal of existing treatment making it smooth with sand paper by mechanical method i.e, with hand electric grinder and applying one coat of exterior Weather proof emulsion paint on walls over a coat of exterior wall primer including all as specified by mechanical method i.e, pray gun complete all as directed by GE/Engineer-in-Charge

S&F PVC connections 15mm size with PTMT nuts of length 450mm

S&F PVC (SWR) bends any radius 110mm dia

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls

Dismantling of cast iron drain pipe of 100mm dia, jointed in CM and taking out from trenches/walls, if required complete all as specified.. Note :- Excavation & earthwork shall be measured and paid separately

Supply and fixing 100 mm nominal dia, UPVC pipe, heavy duty, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, laid in trenches or floors complete all as specified.

Dismantling of cast iron drain pipe of 75mm dia, jointed in CM and taking out from trenches/walls, if required complete all as specified..

Supply and fixing 75 mm nominal dia, UPVC pipe, heavy duty, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls complete all as specified.

Supply and fixing 100mm nominal dia, UPVC bend, heavy duty (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified & as directed by Engineer-in-charge.

S&F 100mm nominal dia, UPVC heavy duty branch pieces, single (equal or unqual), ordinary or inverted (spigot or socket type) or with parallel branches

S&F, 75mm UPVC bend heary duty (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door.

M&L cutting into existing manhole/Septic tank/Soak well for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150mm bore pipe complete all as specified and as directed by Engineer-in-charge.

M&L PCC 1:2:4 type B1, using 20mm graded stone aggregate as in coping, benching and bed blocks etc including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified.

Material and labour DWCPE pipe 150 mm dia ( 160 mm OD) completed laid in trenches including earthwork, removal and return filling and jointed including testing alongwith necessary jointing material tees/union/socket etc complete laid on PCC bed 150mm thick PCC in 1:3:6type C2 of avg depth 0.90 to 1.65 m depth incuding packing under and haunching against the side of pipes after they are laid and tested all as specified in IS 16098:2013 and as directed.

Providing and injecting chemical emulsion treatment should be provided within the plinth area of the ground floor of the structural wherever such cracks are noticed by drilling vertically 12mm hole at the junctions of floor and walls, constructional and expansion joints mentioned these holes using a hand operated pressure pump unit refusal or to a maximum of one ltr per hole. The holes shall be sealed in general the idea is to change the soil below the floor at the location of crack with toxicants. So that termites in the soil are denied access though such cracks and openings in the floor, Infested woodwork in CHAUKATs, shelves, joints purlines etc in contact with the floor or the wall shall be provided with protective treatment by drilling holes of about 3mm diameter with a downward slant to the core of the woodwork on the inconspicuous surface of the frame, these holes should be at least 150mm centre to centre and should cover the entire framework. One of the chemicals given in 4.1 shall be liberally infused in these holes, If the wood is not protected by paint or varnish two coats of the chemicals given in 4.1 shall be given on all the surfaces and services adjoining the masonary and complete all as specified in IS 6313 (Part 3) : 2001 and directed by GE & Manufacture.

RUCHIKA CONSTRUCTIONS

KATARIA CONSTRUCTION

CHILLANA CONSTRUCTION COMPANY