SPECIAL REPAIR TO COOK HOUSE OF HQ AND A SQN (BLDG NO P 22/1S AND P 22 2A) AT ARMD REGT UNDER GE (EAST) FEROZEPUR CANTT

Demolition of unreinforced cement concrete in ground floors and pavings not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

Dismantling floor, hearth or wall/stone tiling including cement mortar bedding (but not backing), removing broken tiles and rubbish off the premises from site complete all as specified and directed.

Dismantling brick work built in cement mortor including all quoins,arches,pillars etc complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness laid, bedded and pointed in any mortar in floors, aprons etc complete all as specified and directed.

Taking up or down existing 15mm bore steel water tubing and connections,including clreaning for refixing or removal, fixed/laid in any situation, complete all as specified and directed.

Taking up or down existing 20mm bore steel water tubing and connections,including clreaning for refixing or removal, fixed/laid in any situation, complete all as specified and directed.

Dismantling 100mm bore cast iron or PVC or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches and taking down from walls, if required complete all as specified and directed.

Dismantling brick tiles or terracing tiles, single layer on roofs jointed and pointed in cement mortar including removal of grass vegitation including roots near out let of RWP and OHT staging area or specifically ordered in writing complete all as specified and directed.

Demolition of mud phuska in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part hereof ) complete all as specified. Note :- Demolition of Mud puska to be cut in average thickness from top surface of roof for creating the slope as directed

Taking down cement plaster of any description on brick walls or concrete or stone and ceilings including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) of size not exceeding 1.5 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts, and removing from site complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) of size exceeding 1.5 Sqm but not exceeding 4 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts, and removing from site complete all as specified and directed.

Dismantling boarding, any description, fixed in any postion with nails or screws complete all as specified and directed.

Demolition of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, complete all as specified and directed.

Roughening surfaces of old concerete floor/roof for removing old bitumen coat/any other type of treatment etc., by picking, sweeping clean and washing down with water to remove dust/dirt etc., complete all as specified and directed.

M&L for Plain Cement Concrete (1:3:6) type C-1 using 20mm graded stone aggregate as in bed blocks of hold fasts, coping etc including necessary form work complete all as specified and directed.

M&L for brick work built in cement mortar (1:6) with sub class 'B' old size bricks, straight or curved on plan exceeding 6m mean radius complete all as specified and directed.

M&L for brick work (EXCEPT BRICKS) built in cement mortar (1:6) with sub class 'B' old size bricks, straight or curved on plan exceeding 6m mean radius complete all as specified and directed. Note:- Old seviceable tiles shall be re-used retrieved after demolition of brick work.

S&F 40mm thick (measured solid) Precast Cement Concrete (1:2:4) type B-0 using 12.5 mm graded aggregate as in louvres and jalies, set in 1:4 mortar including all mouldings but excluding frame complete all as specified and directed.

S&F Pressed steel frames made of 1.25mm thick CRCA sheet of profile 125x60mm for door and window frames with one or more rebates incl lock strike plate, shock absorbers, 20mm dia 60mm long MS conduit for housing of a drop bolt, butt hinges, hold fasts/lugs etc and treating of internal surfaces of chowkhats and hold fasts/lugs with a coat of coal tar or black paint incl hinges, hold fasts/lugs etc including making good jambs portion by providing plaster in CM 1:4 and finishes as per existing complete all as specified.

S&F Pressed steel frames made of 1.25mm thick CRCA sheet of profile 105x60mm for door and window frames with one rebate including lock strike plate, shock absorbers, 20mm dia 60mm long MS conduit for housing of a drop bolt, butt hinges, hold fasts/lugs etc and treating of internal surfaces of chowkhats and hold fasts/lugs with a coat of coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

S&F factory made 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, laminated with 0.9mm thick decorative laminate type 1 of surface finish, colour and pattern approved, fixed with approved adhesive as per manufacturer's instructions including 6mm thick teakwood lipping fixee with adhesive and headless nails complete all as specified and directed.

S&F Anodised aluminium frame for door, windows, ventilators and partitions with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Anodised aluminium window and ventilator shutters, powder coated aluminium (minimum thickness of powder coating 50 micron) side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified complete all as specified and directed.

S&F in replacement Factory Made Box Type Steel Windows with glazing bars made of ERW tube hollow "P" section of size 60mmX25mm double rebated outer frame comprising double shutters side hung skelton & glazed shutters, frame of ERW tube "P" section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and mild steel flat iron 2mm thick welded/ screwed to frame for fixing of wire gauge to frame/ shutters as given below and all as shown on Drawing No. CEJZ/TD-1019/08 and CEJZ/TD-1020/08 Sheet No. 1/3 to 3/3 including taking down of old existing window complete all as specified and directed :- (i) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (ii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iii) MS Tower bolt 150mm long-02 Nos per leaf (iv) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (v) Cleat 55mm long of hollow square 15mmX12mm -02 Nos per leaf (vi) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (vii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). (viii) Preparation of steel surfaces of windows and grills and guard bars and applying one one shop coat of zinc chromate primer and two coats of synthetic enamel paint after installtion at site. Note: Glass panes and grills & guard bars shall be measured and paid for separately .Area shall be measured flat for one side only for the purpose of measurement and payment .

S&F in replacement Factory Made Box Type Steel Windows without glazing bars made of ERW tube hollow "P" section of size 60mmX25mm double rebated outer frame comprising double shutters side hung i.e. guaged shutters, frame of ERW tube "P" section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and mild steel flat iron 2mm thick welded/ screwed to frame for fixing of wire gauge to frame/ shutters as given below and all as shown on Drawing No. CEJZ/TD-1019/08 and CEJZ/TD-1020/08 Sheet No. 1/3 to 3/3 including taking down of old existing window complete all as specified and directed :- (i) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (ii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iii) MS Tower bolt 150mm long-02 Nos per leaf (iv) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (v) Cleat 55mm long of hollow square 15mmX12mm -02 Nos per leaf (vi) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (vii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). (viii) Preparation of steel surfaces of windows and grills and guard bars and applying one one shop coat of zinc chromate primer and two coats of synthetic enamel paint after installtion at site. Note: Wire cloth and grills & guard bars shall be measured and paid for separately .Area shall be measured flat for one side only for the purpose of measurement and payment .

S&F in replacement Factory Made Box Type Steel Ventilators side / top hung with glazing bars or dovetailed or welded made of ERW tube "P"-section of size 60mmx25mm outer frame ( single rebated), comprises glazed shutter, frame of ERW tube and mild steel flat iron 2mm thick welded/screwed to frame for fixing of sheet glass including fixture and fittings like as Stopper, Cleat, Pintal hinges, holdfast etc all as shown onDrawing No. CEJZ/TD-1019/08 and CEJZ/TD-1020/08 Sheet No. 1/3 to 3/3 including taking down of old existing window complete all as specified and directed:- Note : 1. Grills and guard bars, Sheet glass and wiremesh shall be measured and paid separately. 2. Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). 3. Preparation of steel surfaces of ventlators and applying one one shop coat of zinc chromate primer and two coats of synthetic enamel paint after installtion at site. 4. Area shall be measured flat for one side only for the purpose of measurement and payment .

S&F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F 50mmx47mm size solid PVC door frame made out of 5mm plain colour PVC sheet reinforced with MS square tube, complete all as specified shown on drawing and specified and directed.

S&F factory made 30mm thick (style) solid panel PVC door shutter consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified shown on drawing and specified and directed.

S&F 18mm thick Prelaminated particle board, exterior grade, prelaminated both sides with decorative choice laminations, flat pressed, single or three layer type with BWP type phenol formaldihide adhesive as in cup board/ ward robe shutters and shelves including 6mm thick teak wood lipping on three sides of shutters and 20mm thick on hanging side fixed with glue and headless mild steel nails and shuuters fixed with screws to timber frame work complete all as specified and directed.

S&F 75mm size mild steel butt hinges medium weight rolled cold complete all as specified and directed.

S&F 200mm long mild steel barrel tower bolts, stove enameled black, with bright bolt fixed with steel screws complete all as specified and directed.

S&F 75mm size mild steel pressed handle, oval type, stove enameled black and fixed with steel screws, complete all as specified and directed.

S&F 150mm size mild steel pressed handle, oval type, stove enameled black complete all as specified and directed.

S&F stainless steel continous (piano) hinges of mild steel bright finish or electro galvanised with flap (when open) 30mm, fixed with steel screw complete all as specified and directed.

S&F 300mm long mild steel sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

S&F 300mm size mild steel helical door spring ordinery rat rail rod pattern spring including roller and roller plate complete all as specified and directed,

S&F 100mm size hasp and staple aluminium anodised including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F PTMT tower bolts, 200 mm long and fixed with steel screws complete all as specified and directed.

S&F PTMT butt hinges,100mm long, fixed with steel screws with brass /bronze hinges pin complete all as specified and directed.

S&F PTMT handle 125mm long fixed with steel screws complete all as specified and directed.

S&F in repairs Aluminium body hydraullically regulated door closer universal type, suitable for door shutters of 851 to 1000mm width & of weight between 61 to 80kg complete allas specified and diected.

S&F in repairs Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed.

S&F 3.0mm thick, plain sheet glass, ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm in each pane complete all as specified and directed.

M&L for Plain Cement Concrete (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in roof padding surfaces finished even and fair complete all as specified and directed.

M&L for 50mm thick Plain Cement Concrete (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in sub base of flooring, surface finished even and fair complete all as specified and directed.

M&L for 25mm thick Plain Cement Concrete (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in surface finished rough to receive floor topping, surface finished even and fair complete all as specified and directed.

M&L for Green Marble work 18 to 20mm thick in steps ,jambs,pillars,cooking platform and like including pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble shade other than white and black types over a 15mm thick cement screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed.

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over and including 10mm thick cement plaster in back coat in cement mortar (1:4) complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed.

M&L for Machine cut kota stone slab 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, in vertical surfaces such as skirtings, dados, risers and steps etc including rubbing and polishing complete over and including 10mm thick screed bed or bedding layer in cement mortar (1:4) complete all as specified and directed.

M&L for 7 to 8 mm thick (square/ rectangular) Non-skid Ceramic Coloured Tiles, premium quality, area of each tile exceeding 0.11Sqm but not exceeding 0.18Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 10mm thick rendering cement plaster in cement mortar (1:4) complete all as specified and directed.

M&L for 7 to 8 mm thick (square/ rectangular) Non-skid Ceramic Coloured Tiles, premium quality, area of each tile exceeding 0.11Sqm but not exceeding 0.18Sqm, in vertical surfaces such as skirtings, dados, risers and steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 10mm thick rendering cement plaster in cement mortar (1:3) complete all as specified and directed.

M&L for 7 to 8 mm thick (square/ rectangular) Non-skid Ceramic Coloured Tiles, premium quality, area of each tile exceeding 0.18Sqm but not exceeding 0.36Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed.

M&L for 7mm thick (Area 450 x 300mm / 450x350mm/ 350x250mm/300x200mm) Glazed Ceramic Coloured Tiles, in vertical surfacesX 7 mm th set and jonnted in cement slurry and pointed in white or coloured cement in vertical surfaces such as skirtings, dados, risers and steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 10mm thick rendering cement plaster in cement mortar (1:4) complete all as specified and directed.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paverblocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for 12mm thick rendering cement plaster in cement mortar (1:6) on fair faces of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering cement plaster in cement mortar (1:4) on other than fair faces of brick walls or concrete surfaces, mixed with water proofing complound as per manufacturer's instructions, finished even and fair without using extra cement complete all as specified and directed. Note: WPC shall be measured and paid separately. finished even and smooth without using extra cement complete all as specified and directed.

M&L for 10mm thick rendering cement plaster in cement mortar (1:4) on bottom layer of batten roof, mixed with water proofing complound as per manufacturer's instructions, finished even and fair without using extra cement complete all as specified and directed. Note: WPC shall be measured and paid separately. finished even and smooth without using extra cement complete all as specified and directed.

M&L for 5mm thick rendering cement plaster in cement mortar (1:3) on ceiling surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Supply only Integral water proofing compound complete all as specified and directed.

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.20 kg per sqm over a coat of bitumen primer @ 0.30 litre per Sqm including preparation of roof surfaces/ sunken portion and all surfaces of sunken portion complete all as specified and directed.

M&L for One layer of APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified. Polymeric membrane shall be taken to a height of 60 cm (minimum) and then inserted inside the groove of parapet walls and shall be finished by a membrane flashing. Note: (i) Laying of APP based membranes shall be done by torch on method or as per manufacturer's instructions. (ii) A minimum overlap shall be 75mm length wise and 100 mm width wise of polymeric membranes respectively and sealed all overlaps and joints as manufacturer's instructions.

M&L for preparation of surfaces of platered, brick, concrete, polymeric etc, of any description, over10cm in width or girth,not otherwise describedone and applying two coats of Solar Reflective Bituminous Aluminium paint @0.1 Kg/ Sqm over APP Membrane complete all as specified and directed.

S&F gypsum board panel laminated with texture vinyl coated paper tiles of size 595mmX595mmX12mm thick as in ceiling having snap grid 600mmX600mm incl GI wall angle of size 24mmX24mmX0.43mm thick along with perimeter of ceiling, fixed to walls/partition with the help of nylon sleeves at 450mm centre to centre, suspending intermediate tee section of size 24mmX38mmX0.35mm thick suspended from soffit of ceiling at upto 900mm centre to centre or adjustable as required at site 4mm dia GI wire hangers/tightened with ceiling with the help of nylon sleeve/rawl plugs complete all fittings complete all as specified and directed.

S&F hollow PVC wall panelling prelam PVC sheet consisting of 5 mm thick plane colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification & drawings including Dismantling of boarding, any description, fixed in any position with nailscomplete all as specified and directed.

M&L for applying 2.0 mm thick wall care putty omn surface of walls to prepare surface even and smooth complete all as directed.

M&L for preparaion of new surface of walls and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance , dirt resistance exterior paint of required shade (company depot tinted ) with silicon additives @ 1.43 litre/10sqm over and including priming coat of exterior primer applied at 0.9 litre/10sqm over new surfaces complete all as specified and directed.

M&L for preparation of distempering with 1st quality acrylic distemper (ready mix) having VOC content less than 50 gms/litre, of approved manufacturer of required shade and colour complete, as [er manufacturer's specification. Two or more coats on new work complete all as specified..

M&L for Complete removal of existing treatment on wall / ceiling surfaces, including cornices, pilasters, etc, by scrapping down with wire brushes and removing existing loose finishes, loose paricles with brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of existing finishes & foreign materials, making good minor surface imperfections such as holes, dents cracks etc in cement mortar (1:3) and applying 2.00mm thick wall care putty on the surface in two coats and making surface absolutely smoothto the entire satisfaction of Engineer-in-Charge and applying two coats of Acrylic Emulsion white or tinted complete all as specified and directed.

M&L for preparing new plastered surfaces of walls and applying three coats of lime white wash complete all as specified and directed.

M&L for preparing new plastered surfaces of ceiling and applying three coats of lime white wash complete all as specified and directed.

M&L for preparing old surfaces decorated plastered or unplastered surfaces of walls and applying one coat of lime white wash complete all as specified and directed.

M&L for preparing old plastered surfaces of ceiling and applying one coat of lime white wash complete all as specified and directed.

M&L for preparation of new wood or wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of new steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old wood or wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of old steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, fixed to walls or floors complete all as specified and directed. Note:- Only Pipe along the centre line shall be measured and paid except fittings and accessories which shall be measured and paid for separately under respective items.)

S&F 110mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, fixed to walls or floor complete all as specified and directed.Note:- Only Pipe along the centre line shall be measured and paid except fittings and accessories which shall be measured and paid for separately under respective items.)

S&F 75mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 110mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 100mm dia PVC (SWR) Branch piece Double (double "Y") equal or unequal complete all as specified and directed.

S&F 75mm dia PVC (SWR) Branch piece Double (double "Y") equal or unequal complete all as specified and directed.

S&F Stack clamps for 110mm dia pipe made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S&F Stack clamps for 75mm dia pipe made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S&F 25mm dia Unplasticised PVC pipes of pressure rating 10kgf/sqcm fixed to walls,ceilings or in floor etc., any type of pipe complete as specified and directed.

S&F 25mm outer diameter CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls and ceilings or laying in floors complete all as specified and directed.

S&F in repairs 15mm bore Bib Taps, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F 15mm bore fancy type, chromium plated, Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F 25mm bore fancy type, chromium plated, Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipes complete all as specified and directed.

S&F 15mm bore Pillar Taps, fancy type, chromium plated, cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F 32mm bore PVC waste pipe of suitable length to waste coupling pipe attached with rubber ring joints/ PVC threaded cup, fixed to waste coupling of sinks / WHBs/urinal of required length complete all as specified and directed.

S&F 32mm bore Waste fittings of chromium plated brass for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F 15mm PVC connections 450mm long heavy duty with brass nuts adaptors and washers and rubber gaskets at both ends complete all as specified and directed.

S&F 15mm bore Angle Valves, fancy type, chromium plated, cast copper alloy, with flange, one way turn, screwed down high pressure, with crutch or butterfly handle, screwed for iron pipe complete all as specified and directed.

S&F in replacement 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), three layered, ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including 20mm dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule hoisted and fixed including dismentling and taking down old unserviceable water tank capacity 500 litres complete as specified in SSR Part-I. complete all as specified and directed.

S&F in repairs Wash Hand Basins, Vitreous China (flat back) white of size 550mm X 400mm including cutting for and pinning in ends of brackets or erecting stand including waste fittings, 32 mm bore PVC flush pipe with long screwed shucks and fly nuts and including PVC discharge pipe complete all as specified and directed.

S&F in repairs Vitreous China Wash Down Water Closet Pan (pedestal pattern) complete, white/ coloured including seat and cover, trap, including connection to drain (or outgoing pipe), and to flushing pipe, anti-syphonage pipe, etc. etc.complete including all joints and making good to floors complete all as specified and directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified complete all as specified and directed.

S&F in repairs sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mmcomplete all as specified and directed.

S&F in repairs 10 litres capacity low level PVC valveless syphonic action type flushing cistern with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F in repairs 125mm dia Chromium plated brass shower rose with swivel joints, any colour including shower arm 15mm dia, 195mm long with bend of 45 degree with flange of chromium plated brass including fixing complete to steel pipe or union complete all as specified and directed.

S&F in repairs tubular Towel Rail 20mm dia brass chromium plated 600mm long between flanges type "D", with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms)complete all as specified and as directed.

S&F in repairs chromium plated steel soap dish not less than 1mm thickness fixed with chromium plated steel screws and PVC gutties complete all as specified and directed.

Excavating in trenches, in soft/loose soil, not exceeding 1.5m wide and not exceeding 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, cables and pipes etc. not exceeding 10Sqm on plan and not exceeding 1.5m in depth and getting out complete all as specified and as direcetd.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceding 25cm in soft/loose soil complete all as directed.

Removing excavated materials to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L for point wiring with PVC insulated unsheathed single core FRLSH multistranded copper conductor cable IS-694 marked of size 1.5 Sqmm (nominal area) in and including 20mm dia non metallic rigid PVC conduit with all accessories if require such as bends,reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks(for housing lamp holders and light fittings etc) and existing mild steel pressed / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire cable of size 1.5 Sqmm unsheated stranded copper conductor with green PVC FRLSH insulation connected to common earth dolly complete all as specified and directed for One light/fan/Bell Point controlled by one single pole one way switch. Note:- Cutting chases for conduits and sunken boxes and making good to walls, floors etc, in case of recessed and concealed conduit wiring are included in item of taking down point wiring carefully.

ditto all as per item No 113 but for one socket outlet on the same board controlled by one single pole one way switch

ditto all as per item No 113 but for one 5 amps socket outlet independent controlled by one single pole 5 Amp switch.

M&L for point wiring with PVC insulated unsheathed single core FRLSH multistranded copper conductor cable IS-694 marked of size 2.5 Sqmm (nominal area) in and including non metallic rigid PVC conduit with all accessories if require such as bends,reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks(for housing lamp holders and light fittings etc) and existing mild steel pressed / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire cable of size 2.5 Sqmm unsheated stranded copper conductor with green PVC FRLSH insulation connected to common earth dolly complete all as specified and directed for one 3/5 pin 15 Amps switch socket out let on the independent board controlled by one single pole one way switch. Note:- Cutting chases for conduits and sunken boxes and making good to walls, floors etc, in case of recessed and concealed conduit wiring are included in item of taking down point wiring carefully.

M&L for point wiring with PVC insulated unsheathed single core FRLSH multistranded copper conductor cable IS-694 marked of size 4.0 Sqmm (nominal area) in and including non metallic rigid PVC conduit with all accessories if require such as bends,reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks(for housing lamp holders and light fittings etc) and existing mild steel pressed / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire cable of size 4.0 Sqmm unsheated stranded copper conductor with green PVC FRLSH insulation connected to common earth dolly complete all as specified and directed for one 3/5 pin 15 Amps switch socket out let on the independent board controlled by one single pole one way switch. Note:- Cutting chases for conduits and sunken boxes and making good to walls, floors etc, in case of recessed and concealed conduit wiring are included in item of taking down point wiring carefully.

S&F 5/6 Amp Switch piano flush type single pole one way ISI Marked complete all as specified and directed.

S&F 15/16 Amp Switch piano flush type single pole one way ISI Marked complete all as specified and directed.

S&F 5/6 Amp Socket outlet 2 in1, 3 pin flush type ISI marked complete all as specified and directed.

S&F 15/16 Amp Socket outlet 2 in 1, 3 pin flush type ISI marked complete all as specified and directed.

S&F Ceiling Roses Ceiling rose, 3 phase/PVC/polycarbonate, isolated body omplete all as specified and directed.

S&F Lamp holder PVC/Polycarbonate,isolated with back plate suitable for batten fittings ISI marked complete all as specified and directed. including 10W LED Bulb omplete all as specified and directed.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as required complete all as specified and directed.

S&F 450mm sweep Exhaust Fan, steel body AC single Phase. 230V, 900 RPM with blades and frame and louvers with Copper winding including cutting holes/ opening, grouting bolts (12mm dia and 15cm long) , fixing with nuts and washers, making connection wih copper onductor PVC flexible twin wire of size 23/0.0076 and including citting holes and making good in cement mortar (1:4) and finshing surfcae to match with existing surfaces complete all as specified and directed.

Hoist, fix and connect old serviceable Ceiling Fan complete with blades, down rods, electronic regulator and accessories, 230 V, any sweep, size and type, at height 3 to 5m of the building including making connection with copper onductor PVC flexible twin wire of size 23/0.0076 complete all as specified and directed. (Note:- Ceiling fans taken down during taking down point wiring shall be refixed under this item)

S&F LED tube light fitting 1 X 18 W decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient 230V, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size. Cat Part No. LHEXBLP7UN1W018 of Make - Havells or equivalent as specified in Appendix "B" of Particular Specfications, complete all as specified and directed..

S&F LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F LED bulb 9/10 Watt B-22, 65000K, pin type complete all as specified and directed.

S&F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impactand corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. complete all as specified and directed.

S&F sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired VTPN DBs (Verticle type)fitted wit ABS frame, 415 Volts 200Amps rated bus bar,Neutral link,Earth bar and Din rail, 4 ways dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified.

S&F in repairs sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 Volts 200 Amps rated bus bar,Neutral link,Earth bar and Din rail, 8 ways dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified.

S&F Moulded Case Circuit Breaker (MCCB) Four Poles (FP) current carrying capacity 100Amp, 415 Volts, breaking capacity 16 KA with adjustable thermal and magnetic settings, complete all as specified and directed.

S&F Miniature Circuit Breaker (MCB) Single Pole (SP) current carrying capacity 6 to 32 Amp, 240V, breaking capacity 10 KA, type 'B' curve in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

S&F Miniature Circuit Breaker (MCB) Single Pole and Neutral (SPN) current carrying capacity 32 Amp, 240V, breaking capacity 10 KA, type 'C' curve in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

S&F in repairs submain wiring with two single core PVC insulated FRLSH cable with Copper conductor unsheathed cable of size 6.0Sqmm drawn through in and including 25mm dia non metallic rigid PVC conduit with all accessories including one 6.0Sqmm PVC insulated FRLSH cable with Copper conductor unsheathed cable single core for continuous earthing including taking down existing submain wiring and conduits etc complete all as specified and directed. ( Note : Two run of single core PVC insulated cable with Copper conductor unsheathed cable of size 6.0Sqmm and one run of 6.0Sqmm PVC insulated copper conductor single core (2x6.0Sqmm+1x6.0Sqmm earth wire) and one run of PVC conduit shall be measured as single run)

Supply, lay, test, joint and commission LT XLPE insulated , screened, PVC bedded, galvanised steel strip or wire armoured electric powercable heavy duty with aluminium conductor of size cross sectional area 35 Sqmm x 3.2 core, 1100 Volts grade (1.1 KV earthed system); laid in trenches/under floor/through ducts, fixed on pole complete all as specified and directed. Note:- Excavation & Earth work, sand cushioning, cable protection cover, pipe shall be measured and paid separately under respective items of BoQ.

Supply and lay 50mm bore galvanised pipe light grade of ISI marked for passing of cable fixed to poles/walls/laid under floor/ laid in trenches as cable protection complete with and including fittings as required compete all as specified and directed.Note:- Excavation & Earth work, sand cushioning, cable protection cover, pipe and joint shall be measured and paid separately under respective items of BoQ.

M&L for Sand cushioning using sand suitable for plaster works to under ground cable in trenches/existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep punned to 10cm after laying and stretching the cable complete all as specified and directed. Note : 18 cm punned thickness shall be measured and paid.

Supply and lay cable protection cover with Bricks; common burnt clay building bricks, sub-class ‘B’ designation 75, (size 23cmx11.5cmx7.5cm) putting accross the cable with width of protection cover equal to length of brick, abutting to each other for cable protection complete all as specified and directed.

M&L for Earthing complete with Galvanised Iron earth plate electrode 60cmx60cmx6mm thick buried directly in ground vertically at (Earth pit not less than 2.25m deep below ground level) a depth not less than 2.25m below normal ground level with top edge of earth plate at depth not less than 1.5m below normal ground level surrounded from all sides by 15cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connection by using 4mm dia galvanised earth wire by means of bolts, nuts, check nuts and washers of galvanized iron and protected by 15mm bore GI pipe light grade connected to main switch board or main control board and 20mm bore GI pipe light grade for watering and including funnel, wire mesh, 80mm thick pre-cast RCC (1:2:4) type B-1 cover reinforced with hard drawn steel wire fabric weighing not less than 4Kg/Sqm in lieu of CI cover, PCC (1:2:4) type B-1 pit/chamber including all necessary excavation: and earth work, form work, disposal of surplus soil to a distance not exceeding 50m all as specified and al shown in Electrical Plate No.3 of MES Standard Schedule of Rates 2009 Part-I complete all as specified and directed. Note:- (i) The unit rate shall deemed to include for Test point, PCC pit, 4mm dia GI earth wire from top of the earth plate up to 7.5m above ground level. In case 15mm bore GIprotection pipe required is less than 7.5m, no price adjustment shall be made. (ii) PCC pit shall be provided at least 500mm away from the earth pit and not just on the earth pit and extra cost of additional length of water pipes and fittings, junctions, elbow etc shall be deemed to be included in the unit rate. (iii) On testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost.

Please Enable Macros to View BoQ information