Provn of water pipe line, cables and panels at certain different locations near Kalimata Sub Stn and special repair to water supply pipe lines at PB Enclave under GE (Utilities) Udhampur.

Amount

Excavation in trenches n. exc. 1.5 mtr wide and n. exc. 1.5 mtr in depth for laying of GI/CI pipes and getting out in hard / dense soil complete all as specified and directed by Engr-in-Charge.

Excavation in trenches n. exc. 1.5 mtr wide and n. exc. 1.5 mtr in depth for laying of GI/CI pipes and getting out in Soft / loose soil complete all as specified and directed by Engr-in-Charge.

Removing excavated material to a distance n. exc. 50m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge.

Returning, filling in and including spreading, levelling,watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed by Engr-in-Charge.

Supply, fabrication and fixing of MS joints like bends, Tee, tapers, collars, elbow, tail piece (any type) caps, plugs up to 150 mm bore complete all as specified and directed by Engr-in-Charge.

Supply and laying tubes medium grade galvanised plain end with all fittings laid in trenches of size 100 mm bore including all fittings such as bends (any type, radius or angle), tapers any type (straight, bend, increasing, decreasing or double socket etc) TEE pieces single branch, 'Y' Junction, double branch, cross collars, cap and plugs, MS flanges complete bends, TEE pieces, collars, elbow, tail piece etc complete all as specified and directed by Engr-in-Charge. Note :- (i) Flanges to be provided at every 6 m length of plain end pipe or shorter length as directed by Engineer-in- Charge. Flange will be welded to the GI pipe and gasket to be provided between two flanges and will be fixed with 04 Nos of nuts and bolts (M16 Type) at each jointing. Flanges will be of IS-6392 specifications. The cost of flanges, nuts & bolts, gaskets and connecting of flanges to pipeline by welding will be deemed to be included in the quoted item rate. (ii) All standard fittings such as bends (any type, radius or angle), tapers any type (straight, bend, increasing, decreasing or double socket etc) TEE pieces single branch, 'Y' Junction, double branch, cross collars, cap and plugs, MS flanges complete bends, TEE pieces, collars, elbow, tail piece etc jointing are deemed to be included in the quoted item rate. Make of fittings - ISI marked.

(iii) Jointing of pipe line will be done through flanging only and as directed by Engr-in-Charge. (iv) Excavation and earthwork will be measured and paid separately. (v) Any special fittings to be fabricated at site as per typical site condition will be measured and paid seprately. (vi) Welding of flanges to be done by trained personnels at site and included in the quoted rate for normal flange joints for nominal length of pipes. However if the welding of pipes (other than normal flanged joint at nominal length) is required the same shall be measured and paid separately. (vii) Execution of work should be carried out without hampering the daily routine water supply.

Supply and laying tubes medium grade galvanised with all fittings laid in trenches of size 80 mm bore including all fittings such as elbows, Tee, socket, union, reducers, etc complete all as specified and directed by Engr-in-Charge.

All as per serial item No 7.00 here-in-before but of size 50 mm bore.

All as per serial item No 7.00 here-in-before but of size 40mm bore.

All as per serial item No 7.00 here-in-before but of size 25 mm dia.

All as per serial item No 7.00 here-in-before but of size 20 mm dia.

Supply and fixing Butterfly valves of size 80 mm dia, ISI marked cast copper alloy screwed down high pressure with clutch or butterfly handle screwed both ends for iron pipe or for union and fixed complete all as specified and directed by Engr-in-Charge.

Supply and fixing gun metal gate valve of 50 mm dia bore, ISI marked cast copper alloy screwed down high pressure with clutch or butterfly handle screwed both ends for iron pipe or for union and fixed complete all as specified and directed by Engr-in-Charge.

All as per serial item No 13.00 here-in-before but of size 40 mm dia bore.

All as per serial item No 13.00 here-in-before but of size 25 mm dia bore.

All as per serial item No 13.00 here-in-before but of size 20 mm dia bore.

Supply and fixing cast iron sluice valve of size 150 mm dia (PN 1.6) ISI Marked with iron wheel head both end flanged, CI /steel spindle, non rising type complete with neoprene rubber gasket, nuts, bolts and washers etc complete all as specified and directed by Engr-in-Charge.

All as per serial item No 17.00 here-in-before but of size 100 mm dia.

Supply and fixing cast iron air release valves of size 80 mm dia with two air outlets includings all jointing materials like high pressure rubber gasket, nuts , bolts, washers etc and for boring 100/150 mm dia pipe with arrangements for fixing, including taking down, complete all as specified and directed by Engr-in-Charge.

M&L for cutting of existing road for crossing of MS/DI/CI/GI pipes for laying of any size pipes including necessary exacavation and earth work including repairing the same as per existing with pre mix bituminuos carpet complete all as specified and directed by Engr-in-Charge.

M&L for construction of brick/ stone masonary valve pit chamber of size 0.5 mtr x 0.5 mtr x 0.6 mtr internal dimention) with 3.15 mm thick MS cover including 50 x 50 x 6 mm angle iron frame with hinges embedded in coping with locking arrangement and painting the MS surfaces with two coat of redoxide primer. The chamber shall be of PCC 1:4:8 type D2 for foundation, brick work in cement mortar, coping with PCC 1:3:6 type C1, 15 mm thick plastering in cement mortar 1:4 including necessary excavation, earth work and colour washing internally and externally surfaces complete all as specified and directed by Engr-in-Charge.

All as per serial item No 21.00 here-in-before but of size 1.2 mtr x 1.2 mtr x 1.2 mtr.

M&L for disconnecting existing line and connecting to the new line including all necessary fittings such as Tee, union, bend, socket, etc, including excavation, returning, removing complete all as specified and directed by Engr-in-Charge.

Supply, install, testing and commissioning and testing factory made and tested CPRI type test certified) LT feeder pillar box (KIOSK) out door type, floor mounted,compertmantalised suitable for 415 Volts 3 phase 4 wire, 50 Hz AC supply system, dust and vermin proof, made of 2 mm CRCA MS sheet with digital Volt meter, Ammeter, with CTs ,Led lamps RYB for all incomers & outgoings MCCBs are to busbar spadles to fitted complete base frame of 50x50x6mm angle iron , powder coated, having front and rear openeable hinged double door shutters with aprons for cable entry and locking arrangement complete with following :- Incoming :- (a) MCCB160 A 4 pole ,Ics=100%Icu- 25 KA, 415 Volts, with thermal adjustable and fixed magnetic setting with extended terminals -01 No Make:- L&T,Legrand, Scheineiders, Havells. (b) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 250 Amp,4 pole - 01 set.

Outgoing :- (a) On load Change over 100 amps 4 pole ,Ics=100%Icu- 25/26 KA, 415 Volts, with thermal adjustable and fixed magnetic setting with extended terminals -02 No. Make:- L&T,Legrand, Scheineiders, Havells,C&S. (b) MCCB 63A 4 pole ,Ics=100%Icu- 25 KA, 415 Volts, with thermal adjustable and fixed magnetic setting with extended terminals -01 No. Make:- L&T,Legrand, Scheineiders, Havells. Note- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level. (iii) Outgoing MCCBs shall be fed with solid busbar connectors. (vi) including suitable thimbles/lugs, nut bolts ,washers fitted the cables. (v) Cable glands for incoming LT cable 95 sqmm -02 Nos and out going cables 70 sqmm -01 Nos ,35 sqmm -01 Nos and 25 sqmm - 3 is including rate quated by vendover.

S&F in replacement MCCB 4 pole, Ics=100%Icu- 35/36 KA, 415 Volts, 200 Amps , with thermal adjustable and fixed magnetic setting with extended terminals complete all as specified and directed by Engr-in-Charge.

S&F in replacement MCCB 4 pole, Ics=100%Icu- 35/36 KA, 415 Volts, 160 Amps , with thermal adjustable and fixed magnetic setting with extended terminals complete all as specified and directed by Engr-in-Charge.

Supply, Laying and fixing in replacement of along the poles or passing through pipes or laid under floor of through walls etc jointing and testing LT Cross Linked Polythene Insulated (XLPE insulated) galvanized steel strip armoured electric cable 1100 volt grade heavy duty ISI marked with aluminium conductor and overall served with an outer sheath of PVC, of cross sectional area as under including taking out old UNSV LT cables:- (Note : Excavation, earthwork, Pipe for cable protection to be measured and paid for separately)

120 sqmm 3.5 core.

95 sqmm 3.5 core.

M & L for providing earthing with GI earth plate electrode 600 X 600 X 6mm buried directly in ground (earth pit not less than 2.25M deep below ground level ) with top edge of the earth plate not less than 1.5M below ground level connected to GI strip 25 x 4 mm thick for earthing lead fixed by means of nuts,bolt,washers etc connected to earth test point complete all as specified in electrical plate NO 3 of SSR1996 part 1 ,including necessary excavation and earth work in any strata of soil,comman salt, charcoal dust, 40 mm dia light grade GI pipe for protection to earth lead, GI water pipe 20mm dia with funnel &wire mesh , PCC pit with CI cover and frame etc all as specified and directed by Engineer-in-Charge. Note:- (i) All the joints shall be made with welding to get proper conductivity. Note: (ii) On testing after completion of earthing, if desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk & cost complete all as specified and directed by Engr-in-Charge.

Shifting of Generator of capaicites (63KVA-250 KVA) from the Premises of (1 FOD 2 sub depo ) to 1 fod Main office the Generator with help of hydra/crane/any other lifting devices. Including plat form of size length 3 mtrX width 1.5 mtr , height 8" inch Plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundations filling and mass concrete complete all as spd and directed by Engr - in- Charge

S&F double walled corrugated (DWC) pipe of size77mm including snap fit coupler conforming to IS14930 (Pt-II)/IS16205 Pt-II for protection of HT/LT cable in under ground complete all as specified and directed by Engr-in-Charge. Make: REX/Tirupati Plastomatics Pvt Ltd.

SHARMA SALES CORPORATION

PREM NATH KHAJURIA AND SONS

MOHAN LAL AND SONS