MAINT REPAIRS REPLACEMENT OF LT OVER HEAD LINE LT UG CABLE IN POCKET A AT JASAI MIL STN LT FEEDER PILLAR BOX APFC PANEL VOLTAGE STABILIZER UG CABLE AT JALIPA MIL STN UNDER GE A BARMER

Amount

Dismantling of depriciated cross arms (Clamp, nut bolts )/ channels/ supports etc care fully from existing PCC or steel pole/ site and setting aside for reuse or for taking credit all as specified and directed.

Material and labour for steel structure, cross arms, bracing supports ,clamps, back plates febricated from structrual steel sections incl. nuts, bolts, washers, welding ,bending cold or hot drilling holes for bolts in any size and shape all as directed Including one primer coat, one under coat and one finishing coat of synthetic enamel steel paints incl preparation of surface all as directed.

Restringing/Tightening only of ACSR conductor of any type and size of street / security light feeder including straightening properly on insulators and binding with aluminum taps /binding wire /conductor jumper etc complete of any size all as directed. Note : - Single conductor shall be measured for length re-stringing.

Dismantling of ACSR conductor of any type and size from existing PCC/Steel poles at various locations all as directed by Engr - in - charge at site.

Material and labour in replacement of ACSR conductor straightening properly on insulators and binding with aluminum taps /binding wire /conductor jumper etc complete all as directed by Engr- In- Charge.

Dismantling of insulators of any size/type from existing PCC/Steel poles all as directed by Engr - in - charge at site.

Supply and fix pin type porcelain insulator, vitreous brown insulator including one galvanised mild steel spindle with two GI washer and one GI Nuts 100 mm height 65 mm dia for 1100 volts grade, complete all as specified and directed.

Supply and fix shackle type porcelain vitreous Brown insulator 1100 volt grade 75 mm in height and 90 mm dia including galvanised mild steel strap of size 31mm x 3mm , 12 mm dia insulators bolts, washers and nuts complete all as specified and as directed.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5m depth for taking out, laying of cables etc and getting out in soft/loose soil incl connected items complete all as specified and directed.

Returning, filling in, including spreading levelling, watering and well ramming in layers not exc 25 cm in depth (soil) all as specified and directed by Engr-in-Charge.

Removing excavated material (soil) to a distance not exc 50 m and depositing where directed at a level not exc 1.5m above the starting point all as specified and directed by Engr-in-Charge.

Supply and spreading clean dry (Tibba) Sand including watering and consolidation in trenches for cushioning/cable protection all as specified and directed by Engr-in-Charge. Note : Punned thickness shall be measured and paid

Supply and laying un-reinforced precast concrete cable cover, class LV, type 1, flat size 250 mm x 150 mm x 40 mm and abutting each other with gap between adjacent precast concrete cable cover not exceeding 10 mm over underground cables in trenches for cable protection of U/G cables with width equal to length of bricks complete all as specified and directed

M&L for PCC (1:2:4) type B1, using (20mm graded stone aggregate) for coping of poles including necessary form work etc complete all as specified and directed by Engr-in-Charge.

M&L for providing PCC 1:3:6 type C2, Using 40mm graded aggregate for Cement concrete in foundations, filling and mass concrete including necessary form work etc complete all as specified and directed.

M&L for GI pipe of bore 100 mm, light grade with all running fittings (ISI Marked), laid in trenches, under road or fixing on wall/pole/crossing drain/nallah etc., complete all as specified and directed. Make : TATA/JINDAL/PRAKASH. Note : Wherever GI Protection pipes are to be placed/fitted above earths surface, cost of necessary clamping/fixing arrangements to the entire satisfaction of Engr-In-Charge is deemed to be included in the unit quoted rates.

All as per Item No. 16.00 here-in-above, but 80 mm bore pipe.

All as per Item No. 16.00 here-in-above, but 50 mm bore pipe.

All as per Item No. 16.00 here-in-above, but 40 mm bore pipe.

M&L for boring under road manually with labour suitable for inserting upto 100 mm bore pipe at a depth 0.75 to 1.0 mtr complete.

Supply and laying High density Polyethelene pipe (HDPE) of dia 50mm for cable protection in trenches/ducts/floors or fixed on walls / roof etc including suitable fixing accessories complete all as specified and directed by Engr-in-Charge. Note :- Wherever the protection pipes are to be laid/fixed on poles/walls/other surface the cost of clamping using appropriate size/type of MS clamps,nuts both etc is deemed to be included in the unit quoted rates.

M&L for cutting the existing hardstanding/PCC/WBM road at a depth of not less than 60 cm & 30 cm in width for passing of HT cables through GI pipes, returning filling in, complete incl finishing the surfaces by providing cement concrete type B1 (1:2:4) with 20 mm graded aggregate upto 20 cm, finishing to a uniform smooth surface complete all as specified and as directed.

NOTE for item 1.00 to 22.00 :- Any damages made to the existing services of MES/PHED/Defence nits/Other Depts like HT/LT UG cables, Water Supply/Sewage Pipe lines, OFC/BSNL/Signal communication cables etc. during the excavation/boring/road cuting etc. progress of the work shall be made good with proper jointing kits etc. as per original to the entire satisfaction of Engr-In-Charge & GE & the cost of the same is deemed to be included in the unit quoted rates. Decision of the AO shall be final & binding.

Taking out old unserviceable, burnt, punctured aluminium conductor cable LT, PVC/XLPE, 1100 volts grade, of cross sectional area upto 240 Sqmm all as specified and directed by Engr-in-Charge.

Supply, laying, jointing & testing XLPE insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2.0 core in trenches / through GI pipe / fixed along with pole structure etc with all fixing & connecting accessories like Clamps,Lugs and Glands complete all as specified & as directed.

All as per Item No. 24.00 here-in-above, but cable size is 6 Sqmm 2.0 core.

All as per Item No. 24.00 here-in-above, but cable size is 10 Sqmm 4.0 core.

All as per Item No. 24.00 here-in-above, but cable size is 16 Sqmm 4.0 core.

All as per Item No. 24.00 here-in-above, but cable size is 25 Sqmm 4.0 core.

All as per Item No. 24.00 here-in-above, but cable size is 35 Sqmm 3.5 core.

All as per Item No. 24.00 here-in-above, but cable size is 50 Sqmm 3.5 core.

All as per Item No. 24.00 here-in-above, but cable size is 70 Sqmm 3.5 core.

All as per Item No. 24.00 here-in-above, but cable size is 95 Sqmm 3.5 core.

All as per Item No. 24.00 here-in-above, but cable size is 120 Sqmm 3.5 core.

All as per Item No. 24.00 here-in-above, but cable size is 150 Sqmm 3.5 core.

All as per Item No. 24.00 here-in-above, but cable size is 185 Sqmm 3.5 core.

M&L for earthing complete with Copper earth plate electrode 600 x 600 x 3.15 mm thick buried directly in ground (in vertical position) earth pit not less than 2.25 mtr below normal ground level with the top edge of the earth plate not less than 1.5 mtr (B.G.L.) and connected to copper earth strip 20 x 3 mm by means of bolts, nuts, check nuts, and washers of galvanized iron including PCC pit & cover with suitable handle, including necessary excavation and earth work in any type of soil, 20 mm dia med grade galvanized steel tube for watering with one end fixed with suitable funnel and wire mesh, 40 mm bore medium grade galvanized steel tubing for drawing earth lead GI strip protection & common salt, charcoal in alternate layers etc. complete all as shown in EP No 3 of SSR Part 1 Incl Taking down old Existing Unserviceable Earthing of any type alongwith Connected items complete all as specified and as directed and testing on completion complete.

M&L for earthing complete with Galvanised steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (in vertical position) earth pit not less than 2.25 mtr below normal ground level with the top edge of the earth plate not less than 1.5 mtr (B.G.L.) and connected to GI earth strip 32 x 6 mm by means of bolts, nuts, check nuts, and washers of galvanized iron including PCC pit & cover with suitable handle, including necessary excavation and earth work in any type of soil, 20 mm dia med grade galvanized steel tube for watering with one end fixed with suitable funnel and wire mesh, 40 mm bore medium grade galvanized steel tubing for drawing earth lead GI strip protection & common salt, charcoal in alternate layers etc. complete all as shown in EP No 3 of SSR Part 1Incl Taking down old Existing Unserviceable Earthing of any type alongwith Connected items complete all as specified and as directed and testing on completion complete.

NOTE : for item No. 36 & 37 :- 1) On completion of the complete work/job the Contr is to perform earth resistance tests for each earthing job in the presence of the Engr-In-Charge or his rep. If the test results are not satisfactory or not within the permissible limits of relevant Standards/IS then the job is to be redone without any extra cost to the Dept till the results are satisfactory.

M&L for River-Sand filling, levelling, watering & consolidation in 15 cm layers on the level ground surface in Sub-Stns complete all as specified & as directed by the Engr-In-Charge.

M&L for spreading & leveling of stone aggregates of size 20 to 25 mm on sand filling in the Sub-Stns complete all as specified & as directed by the Engr-In-Charge.

M&L for cutting grass, bushes, creapers, weeds, unwanted plants/growths, area cleaning etc in and arround Electric Supply Installations, LT Panels, Feeder Pillar Boxes or any other locations as decided by Engr-In-Charge/GE and removing rubbish off the premises complete all as specified and to the entire satisfaction of the Engr-in-charge.

M&L for preparation of old painted steel surfaces of outdoor/indoor type LT/HT Panels, Feeder Pillar/Junction boxes etc. of any size/type etc. after cleaning of oils, wax, lubricants, grease, rusty scales, spider webs, dusts etc. complete & applying one coat of synthetic enamel paint of approved colour & grade using spray gun & neatly writing distribution details (if applicable) complete all as specified & as directed by the Engr-In-Charge.

M&L for straight through joint, heat shrink type for LT UG Cable incl joint kits suitable for Aluminium conductor cable of size 25 to 50 Sqmm 4/3.5 core incl earthwork, taking down, preparation of damaged cable incl testing complete all as specified & as directed by the Engr-In-Charge. Make : DENSON/3M/YAMUNA/RAYCHEM.

All as per Item No. 42.00 here-in-above but suitable for Aluminium conductor cable of size 70 to 150 Sqmm 3.5 core.

M&L for outdoor jointing kit suitable for XLPE/ PVC Cable 1100 volts grade, heat shrinkable type for indoor/ outdoor applications complete including preparing ends of cable all as directed and specified as under :- (Make: Denson/ Raychem / Birla- 3M) (a) 25 to 50 sqmm 3.5 /4 core

All as per Item No. 44.00 here-in-above, but suitable for 70 to 150 sqmm 3.5 core cable size

All as per Item No. 44.00 here-in-above, but suitable for 185 to 300 sqmm 3.5 core cable size

M&L for preparation of old painted steel surfaces of LT/HT/Security/Street light steel tubular poles incl MS Clamps, cross arms, GI Pipe brackets etc. of any size/type etc. after cleaning/removal of oils, wax, lubricants, grease, rusty scales, spider webs, dusts etc. & applying one coat of Aluminium paint above Coping/GL incl painting of pole coping with Black colour and writing pole No., complete all as specified and directed.

Material and Labour for preparation of old painted surfaces for ZEBRA painting of PCC/steel poles 9/11 m long alongwith road/Perimiter wall with one coat of enamel synthetic paints using yellow and Black colour in alternate layer of 30 cm upto 1.5 mtr above Coping/GL incl painting of pole coping with Black colour and writing pole No., complete all as specified and directed.

S & F in replacement of Steel tubular swaged poles, 9 meters long complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-31 inclusive of one primer coat of red oxide zinc chrome primer and two coats of aluminium paint including preparation of surfaces and writing Pole No complete incl Dismantling of old existing PCC Pole alongwith PCC Coping and removing from site complete all as specified and directed by Engr-in-Charge. Make:IndiaTube&Co./ India Electric Poles/National Tubing Co./ M/s Sankhla Udhyog Note : (i) Design/Drawing/BOM of pole is to be obtained from the Maufacturer/Authorised supplier and the same is to be got approved from Engr-in-Charge prior to making order to the Manufacturer/Supplier. (ii) Earth work and PCC shall be measured & paid separately.

Regular maintenance of existing APFC panel with cleaning of dust inside by blower and cleaning of moving parts / contacts from CT cleaner, tightening of loose parts/ electrical wires, cleaning of contactors, relays and capacitors, junction point,servicing, oiling to cooling fan including testing of APFC relay with necessary setting with CTs / load adjustments to match with the APFC load management system complete with replacement of worn out unserviceable components / burnt wires/ timbles/ lugs of capacity 10 KVAR to 60 KVAR complete all as specified and as directed. NOTE :- (i) There are 15 Nos of APFC panel installed at different locations in Mil stn jassai and all the panels are to be maintained for the complete contract period . (ii) The power factor (PF) for all the 17 Nos APFC panel should be in between 0.95 to 0.99 , in case the PF is less than the power factor maintain above due to any reason, then the contractor shall liable to pay compenssation equivalent to JVVNL tarrif . (iii) The spare parts shall be of same make and capacity of existing one and shall be measured and paid separately. (iv) Replacement of bolt / nut / screws etc. shall deemed to be included in ther rate quoted. (v) Interval of maintenance shall be according to Engr-In-Charge at site

Material and labour for repair to outdoor type double door LT panels/Feeder pillar box by repairing/replacing hinges at site by replacing unserviceable pedestal locks, replacing unserviceable bow handle and connected accessories of front, rear and inner doors by welding, cutting, drilling etc and incl fixing with MS nuts and bolts and repair/ replacing of copper bus bar of various rating suitable along with RYB insulation including cable end terminal aluminium lugs and including spray painting with two coats of approved grade & color synthetic enamel paint after scrapping incl preparation of old painted surfaces over entire LT panel surfeces (Internal and external) of MS sheets and angles complete all as specified and directed at site. (Note : Copper bus bar and porcelain insulators, Meter to be measured and paid under separate Sch 'A' item)

Supply and fix in replacement of old unserviceable voltmeter/ammeter/Multi-function meter with panel mounted multi function three phase digital meter of accuracy Cl-1.0 for measuring V, A,F,PF,KW,Kva, KWh duly painted complete all as specified and directed. Make: Legrand/Schneider/Siemens/ABB/L&T

Supply and fix in replacement of old unserviceable indicators any type with LED based indicating lamps of RYB or any colour in APFC Panel/LT/Bus Bar panel incl disconnecting and connecting of the same complete all as specified and directed.

Supply and fix in replacement of epoxy cast/polymer glass1100V grade insulators on the bus bars/panel complete all as specified and directed.

Supply and fixing in replacement of 200 Amp, 36 KA, 4 pole, thermal magnetic unserviceable MCCB etc suitable for 415 Volts 3 Phase 4 wire system complete all as specified and directed. Make of MCCB : Legrand/ABB/Indoasian/L&T Note : MCCBs shall be lcu=lcs=100%.

All as per Item No. 55.00 here-in-above, but MCCB, AC, 415 volts, 160 Amp, 36 KA, 4 pole, thermal magnetic

All as per Item No. 55.00 here-in-above, but MCCB, 125 Amp, 415 volts, 16 KA, 4 pole, thermal magnetic

All as per Item No. 55.00 here-in-above, but MCCB, 100 Amp, 415 volts, 16 KA, 4 pole, thermal magnetic

All as per Item No. 55.00 here-in-above, but MCCB, 63 Amp, 415 volts, 16 KA, 4 pole, thermal magnetic

S & F Sheet metal enclosure , IP-30. IK-08 where MCCBs to be used, 4 Pole, 415 Volt, Single Door with Suitable louvers for heat dissipation and inbuilt neutral link for TPN sustem ISI marked, cable to be cconnected through suitable lugs and gland complete all as specified and as directed by Engr-in-charge. Make : LK, Cat No CM91003OOOO or techno-commercially equiv in Legrand/Havells.

Supply only in replacement of MCB TPN 415 Volts 10KA, C curve 06-32 Amps in existing panel of the same make in existing MCB to match with existing holes/surface complete all as specified and directed.

Supply only in replacement of MCB TPN 415 Volts 10KA, C curve 40-63 Amps in existing panel of the same make in existing MCB to match with existing holes/surface complete all as specified and directed.

Supply only in replacement of MCB TP 415 Volts 10KA, C curve 06-32 Amps in existing panel of the same make in existing MCB to match with existing holes/surface complete all as specified and directed.

Supply only in replacement of MCB TP 415 Volts 10KA, C curve 40-63 Amps in existing panel of the same make in existing MCB to match with existing holes/surface complete all as specified and directed.

Supply only in replacement of 3 Pole power contactor (capacitor duty type) 415 V of capacity 9 Amps Confirming to IS/IEC 60947-4-1 complete all as specified and directed.

Supply only in replacement of 3 Pole power contactor (capacitor duty type) 415 V of capacity 12 Amps Confirming to IS/IEC 60947-4-1 complete all as specified and directed.

Supply only in replacement of 3 Pole power contactor (capacitor duty type) 415 V of capacity 18-22 Amps Confirming to IS/IEC 60947-4-1 complete all as specified and directed.

Supply only in replacement of 3 Pole power contactor (capacitor duty type) 415 V of capacity 32 Amps Confirming to IS/IEC 60947-4-1 complete all as specified and directed.

Supply only in replacement of capacitor 440 volts 50 HZ APP type electric conforming to IS: 13340/13441 & IEC-831-1 of capacity 1 KVAR complete all as specified and directed.

Supply only in replacement of capacitor 440 volts 50 HZ APP type electric conforming to IS: 13340/13441 & IEC-831-1 of capacity 2 KVAR complete all as specified and directed.

Supply only in replacement of capacitor 440 volts 50 HZ APP type electric conforming to IS: 13340/13441 & IEC-831-1 of capacity 3 KVAR complete all as specified and directed.

Supply only in replacement of capacitor 440 volts 50 HZ APP type electric conforming to IS: 13340/13441 & IEC-831-1 of capacity 4 KVAR complete all as specified and directed.

Supply only in replacement of capacitor 440 volts 50 HZ APP type electric conforming to IS: 13340/13441 & IEC-831-1 of capacity 5 KVAR complete all as specified and directed.

Supply only in replacement of capacitor 440 volts 50 HZ APP type electric conforming to IS: 13340/13441 & IEC-831-1 of capacity 8 KVAR complete all as specified and directed.

Supply only in replacement of capacitor 440 volts 50 HZ APP type electric conforming to IS: 13340/13441 & IEC-831-1 of capacity 10 KVAR complete all as specified and directed.

Supply only in replacement of capacitor 440 volts 50 HZ APP type electric conforming to IS: 13340/13441 & IEC-831-1 of capacity 15 KVAR complete all as specified and directed.

Supply only in replacement of capacitor 440 volts 50 HZ APP type electric conforming to IS: 13340/13441 & IEC-831-1 of capacity 20 KVAR complete all as specified and directed.

Supply only in replacement of capacitor 440 volts 50 HZ APP type electric conforming to IS: 13340/13441 & IEC-831-1 of capacity 25 KVAR complete all as specified and directed.

Supply only in replacement of APFC Controller suitable for measuring 3 phase current and voltage, Displaying PF upto 3 digit after decimal, having dual PF setting for Mains & DG Application including necessary Connection and communication with existing system complete all as specified and directed.

Supply only in replacement of Ampere meter digital type 0 to 100 amps capacity complete all as specified and directed.

Supply only in replacement of CTs suitable for ampere meter 100/5 Amps Rating complete all as specified and directed.

Supply only in replacement of CTs suitable for 200/5 Amps Rating complete all as specified and directed.

Supply only in replacement of CTs suitable for 60/5 Amps Rating complete all as specified and directed.

Supply only in replacement of APFC relay square flush type with protective device intelligent automatic processor based on electronic controller 6 stages for APFC panel complete all as specified and directed.

Supply only in replacement of APFC relay square flush type with protective device intelligent automatic processor based on electronic controller 8 to 14 stages for APFC panel complete all as specified and directed.

M&L in replacement for stay assembly complete with 230x230x 6 mm thick plate and 16 mm dia stay rod all as shown in elect plate No-1 of SSR-part-1 including stay wire of size 7/4mm dia and suitable loop insulator of appropriate size incl taking down old unsv stay wire of any type complete all as specified & as directed. Note : Rate quoted is deemed to be included of excavation in any type of soil, PCC for stay and dismantling of old stay assy.

S&F in repair name board acrylic type (280mm x 400mm) of incoming or outgoing feeders,caution board etc with radium glow sign reflector type on acrylic board incl clamp of suitable size, nut, bolt etc complete all as specified and directed.

Material and labour for writing pole number of minimum size 10 cm height with black paint over base of yellow paint on PCC/steel poles of LT/HT supply complete all as specified and directed.

Supply, install, testing & commissioning of LT busbar junction box "out-door type" of size 750 mm (height) x 750 mm (breadth) x 300 mm (depth) (minimum dimensions), factory fabricated CPRI approved (type-tested) with suitable neoprene rubber gasket to make it completely dust & vermin proof & degree of protection not less than IP-55 & general construction confirming to IS-13947, double door, front & back openable. The box shall be provided with ventilation facility in the form of louvers for better heat dissipation & high grade Copper bus-bar of rating 250A of length 550mm, min spacing of 80mm between the busbars & wrapped with coloured PVC tape /sleeves of rating in conformity to the Incoming cable rating. The panel board shall be fabricated out of 3.00 mm thick (for outer portions) & 2.00 mm thick (for inner portions) CRCA sheet duly pre-treated & powder coated, supporting angle iron frame of height 60cm from GL & MC channel base suitable for 3 Phase, 4 wire system 415 /440 volts grade including I/C & O/G cable opening on bottom & at both sides including cable glands of suitable sizes with suitable PCC (1:3:6) type C-2 foundation , necessary earthwork (if any) incl taking down old unsv box of any size/type complete all as specified & as directed.

Supply, install, testing & commissioning of LT control panel board "out-door type" of size 1500 mm (height) x 1200 mm (breadth) x 500 mm (depth) (minimum dimensions), factory fabricated CPRI approved (type-tested) with suitable neoprene rubber gasket to make it completely dust & vermin proof & degree of protection not less than IP-55 & general construction confirming to IS-13947, double door, front & back openable. The panel shall be provided with ventilation facility in the form of louvers for better heat dissipation & high grade Copper bus-bar wrapped with coloured PVC tape /sleeves of rating in conformity to the Incoming ACB/MCCB rating. The panel board shall be fabricated out of 3.00 mm thick (for outer portions) & 2.00 mm thick (for inner portions) CRCA sheet duly pre-treated & powder coated, supporting angle iron frame of size 50X50X6mm fixed at 75 cm height from groud level & MC channel base suitable for 3 Phase, 4 wire system 415 /440 volts grade including complete internal wiring with not less than 2.5 Sqmm copper wire including cable glands and lugs of suitable sizes with suitable PCC (1:3:6) type C-2 foundation , necessary earthwork (if any) incl taking down old unsv box/Panel of any size/type complete all as specified & as directed. with & including the following accessories :

(i) BUS-BAR & INTERNAL CONNECTIONS : The bus-bars shall be made up of 04 Nos high grade Copper with rating should be suitable as per incoming Breaker, duly insulated with 1100 Volts grade standard colour coded PVC sleeves & rigidly mounted on suitable sized "F" class insulators of non-hygroscopic, non-combustible, all internal connections from main bus-bars to switch gears etc. PROVISION FOR CABLE ENTRY : The provision for cable entry /exit shall be provided in the bottom for both incoming & out-going cables with the help of glands matching the existing LT cable sizes. INCOMING : (a) MCCB 4 Pole (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, having breaking capacity 25 KA & of rating 160-200 A - 01 Nos. Make : L & T, Cat No : CM90642OONO or techno-commercially equivalent of Legrand /Siemens

OUTGOINGS : (a) MCCB 4 Pole (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, having breaking capacity 25 KA & of rating 125-160 A - 01 Nos. Make : L & T, Cat No : CM90642OOMO or techno-commercially equivalent of Legrand /Siemens (b) MCCB 4 Pole (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, having breaking capacity 25 KA & of rating 80 to 100 A - 02 No. Make : L & T, Cat No : CM91712OOKOOG or techno-commercially equivalent of Legrand /Siemens (c) MCCB 4 Pole (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, having breaking capacity 25 KA & of rating 63 to 80 A - 02 Nos. Make : L & T, Cat No : CM91712OOJOOG or techno-commercially equivalent of Legrand /Siemens. (d) MCB TPN "C" series having breaking capacity 10 KA of rating 40 to 63 Amps - 03 No. Make : L&T/Legrand /Siemens. (e) MCB SPN "C" series having breaking capacity 10 KA of rating 06 to 32 Amps - 04 No. Make : L&T /Legrand /Siemens.

S & F in replacement MC4 Male/Female connectors set compatible with module connectors with min of IP66 rating and suitable for 6 Sqmm cable complete all as specified and directed.

S & F in replacement single core annealed copper DC string cable of 1C x 6 Sqmm Solar grade, UV resistant 1.5 kV rated DC Cables with elctron beam XLPE insultaion, maximum energy loss limiting to <1.5% complete all as specified and directed.

S & F in replacement PVC insultated copper cable of single core 6 Sqmm for earthing continuty conductor including suitable copper lugs, screws, nuts & bolts, washers etc. for connecting complete all as specified and directed.

S & F in replacement PVC/XLPE insulated, UV resistant AC copper cable of 4C x 16 Sqmm 1.1 kV rated, including suitable copper lugs, screws, nuts & bolts, washers, cable ties etc., complete all as specified and directed.

M&L in replacement XLPE insulated, armoured, heavy duty electric UG cables with aluminium conductor 1100 volts grade complete including porviding lugs as required as specified and directed for cross-sectional area 300 sqmm 3.5 core., complete all as specified and directed.

M&L in replacement XLPE insulated, armoured, heavy duty electric UG cables with aluminium conductor 1100 volts grade complete including porviding lugs as required as specified and directed for cross-sectional area 300 sqmm single core., complete all as specified and directed.

Annual subsription of superisory control and data acquisition sytem (SCADA) for monitoring and data logging of plant generation and health for FY 25-26 to the existing maintainer of SCADA system (M/s Logics Power AMR Pvt Ltd), complete all as specified and directed.

Annual subscription of GSM mobile numbers (04 Nos) for collection and transporting of generation and plant health data to SCADA system maintainer with 2.5 GB, 4G data/day plan of existing data provider, complete all as specified and directed.

S&F in replacement HRC fuse link of rating 33-36 KV 3.15 A rating for PT of 33 KV VCB unit complete all as specified and as directed. Make Phoenix or equivalent

S&F in replacement Cast resin potential Transformer 36 kV/110 V single phase 100 VA burden 50 Hz , class 0.5, voltage factor 1.2 cont & 1.5 for 30 Sec insulation level 36 KV/70KV/170 KVP including necessary control wiring complete all as specified and as directed

M&L in replacement 40 to 50 mm thick roughly hammered dressed stone 25 to 30 cm wide length approximately 1.5 meter ± 10% for covering cable trench from LT panel to transformer, laid dry and abutting each other with gap adjacent slab not exc.10 mm for protection of cable complete all as directed

S&F in replacement flexible hose 25 mm dia for protection of DC/AC cable laid below the solar modules including the necessary ties complete all as specified and as directed.

Supply, jointing and testing cable jointing kit for 33 KV grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 120 Sqmm including taking out old one complete all as specified and directed . Make: Raychem EPKT 6364 orequivalent.

Supply, jointing and testing cable jointing kit for 33 KV grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 120 Sqmm including taking out old one complete all as specified and directed. Make: Raychem EPKJ 6116 or equivalent

M&L for boring/drilling by machines/manual horizontally under the road in any type of soil without cuttiing/disturbing the existing road and inserting GI pipe of any size for drawing the cable complete all as specified.(GI pipe shall be measured and paid seperately.

Excavation in post holes (or similar holes) each not exc 0.5 cum getting out , returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard/dense soil complete all as directed.

M&L in replcement XLPE insulated, armoured, heavy duty electric UG cables with aluminium conductor 1100 volts grade, for cross-sectional area 16 sqmm 2 core, complete including porviding lugs as required as specified and directed

All as per item No 111.00 here in before but cable size is 25 Sqmm, 3.5 core

Dismantling/uprooting of LT unserviceable pre-stressed concrete/steel poles of any size and length including taking out dismantled portion of poles embeded in concrete after necessary demolition of concrete foundation and disposal there of as directed by the Engineer-in-Charge.

M & L in replacement for Prestressed concrete pole, 9.0 metres long, 102 mm x 152 mm at top and 102mm x 289 mm at bottom, class 10, complete all as specefied and directed.

Fixing only serviceable cross arm, MS Channel, angle section obtained from item No 1.00 here-in-before after painting with one coat of aluminium paint including preparation of old steel surfaces complete all as specified and directed.

Fixing only serviceable pin type porcelain, vitreous, (white/brown or green) insulator for 1100 volts grade of any type obtained from item here-in-before, complete all as specified and directed.

Fixing only serviceable shackle type porcelain, vitreous (white / brown or green) insulator of any size and shape for 1100 Volts grade obtained from item here-in-before, complete all as specified and directed.

S&F in replacement loop type insulators vitreous porcelain white / brown or green small size with overall dimensions 65x90 mm clearance of hole 16 mm dia, complete all as specified and directed.

Dismantling earth wire of any size/dia, guarding cradle of disturbed span and keeping serviceable materials in safe custody for re-use and removing unserviceable materials from the site complete all as specified and as directed.

Fixing only serviceable GI wire 3.15 mm or 4 mm dia martial obtained from item here-in-before complete all as specified and directed.

M&L for cradles, hexagonal / rectangular, fabricated or continuous earth wire with galvanised steel wire 3.15 mm or 4 mm dia complete as specified and directed.

S&F in replacement PVC fibre separator for LT line 1100 volt OH conductor 3/4 wire system for maintaining horizontal spacing of conductor complete with nut & bolt minimum two nos in a span complete as specified and directed.

Trimming of tree branches around the LT /HT OH conductor, pole & stay (not less than 3 metre) to clear the over head lines including cleaning of birdnest, creepers on poles and stays etc complete as required including removing and disposed off from the site as directed.

M & L in repair earthing complete with galvanised steel earth plate electrode 600X600X6 mm thick buried directly in ground preferably vertically in ground with top edge not less than 1.25 mtr deep below normal ground level connected with and including galvanised iron wire 4 mm dia as earthing lead by means of nuts bolts and washers of galvanized iron protected by 15mm dia (medium grade) GI tubing, funnel, wire mesh, 20mm bore GI tubing (light grade) watering pipe , including concrete pit in PCC (1:3:6) type C-1, precast RCC (1:2:4) type B-1 cover slab of size 350x350x50mm reinforced with 8mm dia TMT bars @ 15cm c/c in both ways and 10mm dia MS handle (01 No) of suitable size, charcoal and salt in alternate layers necessary excavation and earth work in soft/loose soil all as shown in Electric plate No. 3 of SSR part-I and testing on completion complete all as specified and as directed.

Supply, install, commission and testing in replacement cubical type LT panel board ,outdoor canopy type, manufactured by a CPRI approved factory, floor mounted, dust & vermin proof,front and rear operated door with necessary locking arrangement made of 50 x 6mm MS angle iron frame work and CRCA sheet of 3.00 mm thick duly painted with two coats of powder coated paint of approved shade after seven tank treatment process both internally and externally. The panel shall be suitable for 415 Volts, 50 HZ, 3 Phase 4 wire system and shall be complete with suitable capacity copper bus bar (1.5 times the incoming switch gear current rating) with suitable size of PVC insulated copper conductor, thimbles glands complete all as specified and directed with the following accessories :- INCOMING (a) MCCB 4 pole, 415 Volts, 250 Amps, 25 KA - 01 No. OUTGOING (a) MCCB 4 pole, 415 Volts, 125 Amps,16 KA -01 No. (b) MCCB 4 pole, 415 Volts, 100 Amps,16 KA -02 Nos (c) MCCB 4 pole, 415 Volts, 100 Amps,10 KA -01 Nos (Spare) (d) MCB TPN , 415 Volts, 32 Amps, -01 Nos (e) Digital VAF meter for basic electric system monitoring-01 Nos. (f) Indicator lamp (RYB) (set of three) - 01 Set

S&F in replacement TPN copper bus bar box, outdoor type of 200 A capacity mounted on porcelain bridge insulator for one incoming cable and 4 out going cable, housing in sheet metal enclosure of MS sheet 3.0 mm thick CRCA sheet and angle iron 40x40x6 mm frame, painted with two coats including arrangement for cable gland for incoming and outgoing cables, locking arrangement, suitable foundation/platform for mounting the FPB with space for and including the following switch gears: (a) MCCB 100 A FP, 10 KA (for incoming control)

Preparation of old painted surface above the planting depth and PCC coping of steel tubular LT pole of 09.00 metre length including MS clamps ,cable protection pipe bracket fitted with street light fittings etc by scraping with steel wire brush and applying two coats, of aluminium paint to external surface of poles MS cross arms MS clamp, cable protection pipe etc to give even shade including Zebra colour of painting from 1.5 mtr height from the top of coping/ bottom of pole as per site condition and numbering of poles, complete all as specified and directed. Note: Zebra colour will be applied by synthetic enamel paint of black/yellow colour as approved in alternate layer of 30 cm height of each layer.

M&L for preparation of old painted surfaces and removing dust and other deposited material by scraping from LT PCC poles of 09.00 metre length, cross arms brckets and applying 2 coats of aluminium paint to all steel surfaces, including MS clamps ,cable protection pipe bracket fitted with street light fittings etc including Zebra colour of painting upto 1.5 mtr height from the top of coping/ bottom of pole as per site condition and numbering of poles complete all as specified and as directed by Engr-in –charge

S&F in replacement energy efficient LED street light fitting of 45 watt made up of pressure die cast aluminium housing with toughened glass and high power LEDS with secondary optics, efficacy 110/120 LPW, IP 66 protection aerodynamically designed for all weather conditions with efficient thermal management including 10 KV SPD, complete all as specified and directed. Model: RAPTOR NEO Cat No : TRP-409-45-57-SL-GL-NSG of make CG or equivalent model of Havells, Bajaj, Wipro, Halonix

S&F in replacement energy efficient LED street light fitting of 60 watt made up of pressure die cast aluminium housing with toughened glass and high power LEDS with secondary optics, efficacy 110/120 LPW, IP 66 protection aerodynamically designed for all weather conditions with efficient thermal management including 10 KV SPD, complete all as specified and directed. Model: RAPTOR NEO Cat No : TRP-409-60-57-SL-GL-NSG of make CG or equivalent model of Havells, Bajaj, Wipro, Halonix

S&F in replacement LT service cable 6 sqmm 2 core inside PVC conduit 20 mm dia medium grade for landscape lighting/ garden lighting inside trench or on wall/floor, complete all as specified and directed. Note: The rate quoted must be inclusive of laying the cables in trench at max 10 cm depth or mounting on floor/wall

S&F in replacement Integral compact wide beam LED flood light luminiaire with die cast aluminium alloy housing with IP 66 protection, tampered protective toughened glass 5mm thick, thermal shock impact resistant cover, epoxy black powder coated finish, high purity pre-anodised specular aluminium sheet reflector, with silver painted contacts suitable for 1x100 Watts LED and connection with two runs of 2.5 Sqmm multi-stranded, copper flexible wire including taking down old unserviceable one and testing complete as specified and as directed by the Engineer-in-Charge. Cat No LHEPCZU7PA6J100 Havells or Wipro and Crompton

S&F in replacement LED post top lantern of 45 W, IP 65 protection with in built electronic driver and aluminium housing in pure polyster UV resistant powder coated black finish, top maintainable product with top opening die cast cover , anti corrossive stainless steel screws & silicon gasket, HET PMMA diffuser conforming to IS 10322 Part 5/Sec 1: 1987, suitable for pole diameter up to 75 mm , cable entry through pole from bottom, 3 way 10 Amps GFP mains connector duly wired upto terminal block complete all as specified and as directed. Make Wipro Cat part No: LP07-501-XXX-57-CL or equivalent in Bajaj, Crompton, Havells, halonix.

S&F in replacement GI pipe bracket for street light fittings made out of 32 mm dia GI pipe light grade 1.5 mtr long bent to required angle/ shape with and including necessary clamps, nuts, bolts, & washers of suitable size all as directed by Engineer - in - Charge

S&F in replacement PVC weather proof loop-in loop-out box with 4 pole terminal block mounted on porcelain or bakelite and MCB SP 06 Amps for controlling including necessary clamps for mounting on pole etc complete all as specified and directed. Make: Sintex Cat Part No-GSJB 2014 or techno commercially equivalent.

S&F in replacement Indicator lamp, LED type of colour red, blue and yellow including taking down existing old/unserviceable lamps from LT panel /APFC Panel board after carefully disconnecting the electric connection complete all as specified and asdtrected.

S&F in replacement MCCB, 415 volts, 400 Amp, breaking capacity 36 KA, 4 pole including taking down existing old/unserviceable MCCB from LT panel /APFC Panel board after carefully disconnecting the electric connection complete all as specified and as directed

S&F in replacement MCCB, 415 volts, 250 Amp, breaking capacity 25 KA, 4 pole,including taking down existing old/unserviceable MCCB from LT panel /APFC Panel board after carefully disconnecting the electric connection complete all as specified and as directed

S&F in replacement MCCB, 415 volts, 200 Amp, breaking capacity 25 KA, 4 pole, including taking down existing old/unserviceable MCCB from LT panel /APFC Panel board after carefully disconnecting the electric connection complete all as specified and as directed

S&F in replacement MCCB, 415 volts, 160 Amp, breaking capacity 16 KA, 4 pole including taking down existing old/unserviceable MCCB from LT panel /APFC Panel board after carefully disconnecting the electric connection complete all as specified and as directed

S&F in replacement MCCB, 100 Amp, 415 volts, breaking capacity 10 KA, 4 pole, including taking down existing old/unserviceable MCCB from LT panel /APFC Panel board after carefully disconnecting the electric connection complete all as specified and as directed

Note:- Qty's are clubbed for 2 Nos CPP Job. Qty's details for item No. 1.00 to 15.00, 24.00, 26.00, 27.00, 29.00 TO 34.00, 37.00, 57.00 & 88.00 details as per Annexure-I on Sl. Pg. No. 57 of Tender Document. Rest all items qty's as below mentioned:- (i)- CPP Sl. No. 27 of Jalipa Mil Stn:- All qty's for item No. 16.00 to 92.00 excluding items mentioned above Note. (ii)- CPP Sl. No. 17 of Jasai Mil Stn:- All qty's for item No. 93.00 to 143.00.

National Rewinding Works (BID ID -3459720)

GITANSH ENGINEERS AND COMPANY (BID ID -3457372)

DEVARAM CONSTRUCTION COMPANY (BID ID -3457774)

Rasam Engg Co. (BID ID -3457657)