SPL REPAIR TO FURNITURE AGAINST BER BOARD AT AYODHYA UNDER AGE (I) AYODHYA CANTT

Amount

CHAIR VERANDAH (DRG NO. FD-359) (a) The overall size of the chair shall not be less than 460mm wide x.600mm deep and 355mm high upto seat from ground level and over all height 760 mm. (b) The frame shall be made of 20mm dia MS conduit pipe of wall thickness 1.6mm. Canning seat & back shall be done with 4mm wide plastic cane in Godrej pattern or as directed by AGE(I) / Engineer-in-Charge. 10mm dia mild sleet round bar shall be welded horizontally to front legs at 75mm from bottom of seat. (c) PVC hard rubber shoes / toes shall be provided to all legs of chair verandah. (d) All steel surfaces shall be pre-treated with epoxy polyester powder coating white 70 micron by 7 tank process and oven dried externally with the following specifications:- (i) Dry film thickness more than 45 micron (ii) Salt spray test to withstand more than 1000 hours (iii) Adhesion as per DIN 53152 standard (iv) Pencil scratch hardness more than 2H. (e) All other specifications and dimensions shall be as shown on drg.

PEG TABLE (DRG NO. FD-277) (a) Timber shall be first grade kiln (plant) seasoned teak wood as per IS-1331:1971, free from knots and cracks with moisture content permissible as per IS-287:1973. (b) Overall size shall be 450mm long x 300mm wide and 380mm high. (c) Legs shall be of teak wood of section 30mmx50mmx362mm high. 5mm x 5mm groove shall be provided on top of legs which shall be visible when placed in position. 02 Nos top rails of section 20mm x 40mm shall be provided between the legs along long side to connect the legs at top and 2 Nos bottom rails of size 20mm x 40mm shall be provided along short side to connect the legs. A centre stiffener of size 20x40mm shall be provided at centre to coonect bottom rails for extra support irrespective of what is shown on drg.

(d) All the wooden joints shall be fixed with bamboo pins and nails shall not be used. All joints and fixing shall be done in accordance with the standard workmanship / specification. (e) Top shall be made of 18mm thick MDF board Exterior grade duly post -formed with 0.6 mm thick larmnate of colour/shade as approved by EIC/AGE (I) with 2 mm thick PVC edging of on two sides with strong bonded chemical adhesrve through hot pressed machine and other side with balancing white sunmica, rest all as shown on drawing. (f) All exposed wooden surfaces shall be smoothened and prepared for polishing. Applying two or more coats of best quality Melamine polish usingy spray gun machine in Mahogany/Wallnut Colour to give glossy finish. Polish and colour shade shall only be done in BSO Yard as directed by Engr-in-Charge

TABLE BED SIDE (DRG NO. FD/E6/MAP/15(R) (a) The overall size of table bed side shall be 450mmx450mm x 600mm from rear and 450mm x450mmx500mm at front all as shown on drg. (b) lrrespeclrve of whatever is shown on drawing, the entire frame of table bed side shall be made of 18mm MS Square pipe (18 Gauge). (c) Top shall be made of 18mm thick MDF Board exterior grade duly post formed with 0.6 mm thick laminate of approved colour/shade with 2 mm thick PVC edging on two sides fixed with strong bonded chemical adhesive through hot pressed machine and other side with balancing white sunmica. The back of the table except the top portion as shown on drg shall be provided with 6mm thick commercial plywood BWR Grade duly screwed to frame complete alla s specified and directed by Engr-in-Charge.

(c) Drawer : Sides & back shall be made of 12 mm thick BWR garde plywood and bottom shall be made of 6mm thick commercial plywood irrespective of whatever is shown on drg and front side of drawer shall be made of 18mm thick pre-larrnnaled MDF Board. The whole plywood surfaces shall be painted with two coats of white paint with over a coat of wood primer. Each drawer shall be provided with 2 Nos stainless steel Telescopic Channel for smooth running and CP handle of 4" size complete all as specified and directed by Engineer-in-Charge. (d) All metal surfaces shall be dry powder coated in black and all un-laminated surfaces shall be polished in satin/mat melamine finish of walnut shade after preparation of surfaces. (e) All other details shall be taken as shown on drg and directed by Engr-in-Charge.

TABLE 3'x2' WITH DRAWER (DRG NO. FD-283) (a) Table 3'x2' with drawer shall be made to the shape, size and design as shown on drg. Short stiffener to be provided to join bottom rails in between legs as directed by AGE (I)/Engr-in-Charge, irrespective of what is shown on drg. AII the wooden joints shall be fixed with bamboo pins and nails shall not be used. (b) All joints and fixing shall be done in accordance with the standard workmanship / specification. (c) Top shall be made of 18mm thick MDF Board exterior grade of duly post -formed with 0.6 mm thick laminate in approved colour / shade with 2 mm thick PVC edging on two sides fixed with strong bonded chemical adhesive through hot pressed machine and other side wilh balancing white sunmica. All other details shall be as per drawing or as specified and directed by AGE(I)/ Engr-in-Charge.

(d) Irrespective of whatever is shown on drg, Front of drawer shall be made of 18 mm thick BWD grade plywood duly pasted with 0.8mm thick sunmica of approved shade with suitable adhesive as approved by Engr-In-Charge/AGE(I). Back & sides shall be of 12 mm thick BWP grade of plywood and bottom of drawer shall be 6 mm thick BWP Plywood. Telescopic channel and CP handle 4" shall be provided in drawers all as directed by AGE(I) / Engr-In-Charge and as per drg. Duco paint to be applied two coats on all surfaces except front of drawer. (e) All exposed wooden surfaces shall be smoothened and prepared for polishing. Two or more coats of best quality Melamine polish shall be applied usingy spray gun machine in Mahogany/Wallnut Colour to give glossy finish. Polish and colour shade shall only be done in BSO Yard as directed by Engr-in-Charge

TABLE 3'x2' WITHOUT DRAWER (DRG NO. FD-284) (a) Table 3'x2' without drawer shall be made to the shape, size and design using Ist class hard wood (teak wood) as shown on drg. (b) Short stiffener to be provided to join bottom rails in between legs as directed by Engr-in-Charge irrespective of whatever is shown on drg. (c) All the wooden joints shall be fixed with bamboo pins and nails shall not be used. All joints and fixing shall be done in accordance with standard workmanship and specification. (d) Top shall be made of 18mm thick MDF Board exterior grade of duly post -formed with 0.6 mm thick laminate in approved colour / shade with 2 mm thick PVC edging on two sides fixed with strong bonded chemical adhesive through hot pressed machine and other side wilh balancing white sunmica. All other details shall be as per drawing or as specified and directed by AGE(I)/ Engr-in-Charge. (e) All exposed wooden surfaces shall be smoothened and prepared for polishing. Two or more coats of best quality Melamine polish shall be applied usingy spray gun machine in Mahogany/Wallnut Colour to give glossy finish. Polish and colour shade shall only be done in BSO Yard as directed by Engr-in-Charge

TABLE DINING JCOs / ORs FOR 04 PERS (DRG No. FD/MAP-II/03) (a) Table Dining JCOs / ORs shall be made to the shape, size and design as shown on drq. (b) All wooden joints shall be fixed with bamboo-pins and nails shall not be used. All joints and fixing shall be done in accordance with the standard workmanship / specification. (c) Top shall be made of 18mm thick MDF Board exterior grade of duly post -formed with 0.6 mm thick laminate in approved colour / shade with 2 mm thick PVC edging on two sides fixed with strong bonded chemical adhesive through hot pressed machine and other side wilh balancing white sunmica. (d) All exposed wooden surfaces shall be smoothened and prepared for polishing. Two or more coats of best quality Melamine polish shall be applied using spray gun machine in Mahogany/Wallnut Colour to give glossy finish. Polish and colour shade shall only be done in BSO Yard as directed by Engr-in-Charge (e) All other details shall be as per drawing or as specified and directed by AGE(I)/ Engr-in-Charge.

CHAIR WRITING (DRG NO. FD/E6/MAP/12) (a) Chair Writing with cushion shall be made to the shape, size and design as shown on drawing. Frame shall be made of 25mm x 10mm size powder coated MS tubular sections, cantilever type. One piece arm rest made of black integral skin polyurethane with 75- 85 shore 'A' hardness and reinforced with MS insert, It shall be scratch & weather resistant. Both hand rest sections shall have slope towards front. Bending, welding, riveting, bolling, lapping, turning and other items / fitting shall be done / provided as specified in relevant IS and as per trade engineering norms and pattern. (b) Polyurethane foam shall be 50mm thick and shall be moulded with density 50-55 kg per cubic meter and hardness 20 Plus(+) 2 Kg on hampden machine. Back foam shall be designed with contoured lumber support for extra comfort and 12mm hot pressed plywood upholstered with fabric and moulded polyurethane foam with PVC lipping all round. Fabric shall be contained the materials in various colours Acrylic, polyester, poly propylene and shall be as approved by AGE (I)/Engr-In-Charge. (c) Four numbers ot rubber stoppers shall be provided at bottom of the chair. Steel surfaces shall be powder coated. All other Item/fittings shall be as shown on drawing and provided as per relevant IS and trade engineering norms/ Pattern. (d) Other specifications shall be as per drawing or as specified and directed by Engr-in-Charge.

TEAPOY (DRG NO. FD-382) Overall size shall be 600mm long x 450 mm wide and 540mm high. (a) All timber shall be well seasoned 1st class teak wood (MP). (b) Top shall be made of 18mm thick MDF Board exterior grade of duly post -formed with 0.6 mm thick laminate in approved colour / shade with 2 mm thick PVC edging on two sides fixed with strong bonded chemical adhesive through hot pressed machine and other side wilh balancing white sunmica. (c) All exposed wooden surfaces shall be smoothened and prepared for polishing. Two or more coats of best quality Melamine polish shall be applied using spray gun machine in Mahogany/Wallnut Colour to give glossy finish. Polish and colour shade shall only be done in BSO Yard as directed by Engr-in-Charge (d) Other specifications shall be as per drawing or as specified and directed by Engr-in-Charge.

ALMIRAH MEDIUM WITH SHELVES (DRG NO. FD-1032) (a) Almirah medium steel with shelves shall be made to the shape, size and design as shown on drg. (b) 1mm thick CRCA sheet shall be used for fabrication of entire body, shelves and legs irrespective of what is shown on drg. (c) Almirah shall be provided with one spring action recessed handle 150 mm long with built-in locking arrangement filled to cut out space in one shutter as per "Godrej pattern" as approved by AGE (I) / Engr-in-Charge. (d) The welding joints shall be filed smooth before application of primer. The surfaces shall be cleaned and prepared piror to applying of paint. All exposed sleet surfaces internally and externally shall be painted with hammer tone sprayer over a coat of red oxide primer. The colour / shade of outer steel body shall be in dual shade (Shades shall be approved by AGE(I)/ Engr-in-Charge. (e) Other specifications shall be as per drawing or as specified and directed by Engr-in-Charge.

CHARPOY IP HARD TOP / PLY TOP (DRG NO. FD/MA-II/01) (a) The overall size shall be of 1980mmX900mmX 440mm (b) The frame work shall be made of CRCA box sections as under:- (i) Long Rails - 25X65mm box section of 16 guage (ii) Short Rails - 25X65mm box section of 16 guage (iii) Legs - 32X32mm box section of 16 guage. MS plate of size 32X32X5 mm thick shall be welded at bottom of each leg under which 3 mm thick rubber shoe to be fixed with strong adhesive. (iv) Stiffeners for legs - 2 Nos, each of size 25X25 mm box section of 16 gauge thick. (v) Stiffener between long rails - 2 Nos, each of 25X25mm box section of 16 gauge thick.

(c) The bed top shall be 12 mm thick plywood top BWP grade as per existing shape and size with 10 Nos sunken nuts & bolts, appropiate hole shall be made with electric drill machine complete rest all as per drg and directed by Engr-in-Charge. (d) All metal work shall be epoxy powder coating after applying metallic putty and preparation of surface smooth. (e) Other specifications shall be as per drawing or as specified and directed by Engr-in-Charge.

ALMIRAH LARGE WITH SHELVES DRG NO. FD-1031) (a) Almirah large steel with shelves shall be made to the shape, size and design as shown on drg. (b) 1mm thick CRCA sheel shall be used for fabrication of entire body, shelves and legs irrespective of whatever is shown on drg. (c) Almirah shall be provided with one sping action recessed handle150mm long wilh built in locking arrangement and to be fitted to cut out space in one shutter as per "Godrej pattern" (d) The welded Joints shall be filed smooth before application of primer. The surfaces shall be cleaned and prepared prior to applying of paint. All exposed steel surfaces internally and externally shall be painted with hammer tone sprayer over a coat of red oxide primer. The colour/shade of outer steel body shall be in dual shade as approved by AGE(I) / Engr-in-Charge (e) Other specifications shall be as per drawing or as specified and directed by Engr-in-Charge.

Sheo Prasad (BID ID -3352794)

JAISWAL ENTERPRISES (BID ID -3353691)

M/s M K Sons Steel Industries (BID ID -3361988)