REPAIR/MAINT OF SWIMMING POOL, DIVING TANK, REPAIR OF SUBMERSIBLE PUMP, CENTRIFUGAL PUMP, PRESSURE FILTER, CLEANING OF OH TANK, REPLACEMENT OF PIPE LINES DI/GI FITTINGS, JOINTS AT AATS UNDER GE (EAST) AGRA

Amount

Excavation in trenches not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr deep in soft/loose soil and getting out for taking down/laying Pipe lines of any description and in any position including forming sides and bottom surface to required level/ gradients complete all as specified and directed.

Returning, filling in, excavated soil including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed.

Removing of surplus soil to a distance not exceeding 50 M and depositing where directed at a level not exceeding 1.5M above the starting point complete all as specified and directed.

Supply and spread sand in trenches as sand cushioning to underground cable for protection with dry fine river sand and provide required cover after punning down complete all as specified and directed. (Note : Thickness of sand cushion after punning down will be measured and paid.)

Supply and laying well burnt sub class ‘B’ bricks ( designated 75) locally available best quality, laid dry in trenches for protection of underground cable complete all as specified and directed.

Material and labour for desilting and cleaning of Horizontal pressure filter(length 4.60 mtr, dia 2.50 mtr) by using iron brushes, taking out sludge, mud, sand etc on floor / wall and taking out from the tank by pulley / ladder, removing unserviceable materials to a distance and cleaning the floor and wall thoroughly with clean water to remove all dirt, scale, mud etccomplete all as directed. Necessary pully, ladders, ropes and other items etc required at site for work of is deemed to be included in the unit rate quoted by the contractor. On completion of cleaning of tank, date of cleaning to be marked / written clearly on tank surface in an accessible location with letters or figure not exc 20cm high viz “TANK CLEANED ON -” (Qty of sand and pebbles to be measured in respective items) complete all as specified and directed.

Supply only Support Filter Media (Brown pebbles) complete all as specified and directed.

Supply only Main Filter Media (Brown Sand) complete all as specified and directed.

Supply only silicate sand (8/16 &16/32 wash) complete all as specified and directed.

Removing of old paint by removers scrubing from Horizontal Pressure Filter Plant complete at swimming pool complete including pumping sets, pipes etc for painting and M &L for painting with one coat of superior quality synthetic paint with approved colour on exposed surface of plant etc and writing letters or figures (Block, Roman, Italic or Indian) n exc. 30 cm high and drawing stops, commas, short lines, dashes, hyphens, brackets etc. with synthetic enamel paint [SM/MES No., Capacity, Location etc.] complete all as specified and directed.

M&L for repair to leakage of DI/CI 100/80 bore water mains including disposal of water from trench by manualy or mechanically, excavation and earth work in any type of soil, burning out old lead, cleaning joints and filling with and including fresh pig lead and cocking to make joint leak proof compete all as specified and directed. Note : If new lead joint provided shall be paid seperately under above relevent items.

M&L for repair to leakage of GI 100/80/50/40 bore water mains including disposal of water from trench by manualy or mechanically excavation and earth work in any type of soil, replacement of minor fitting such as sockets, union, threading, screwing etc make joint leak proof compete all as specified and directed.

M&L for repair to leakage of GI 25/20 mm bore water mains including disposal of water from trench by manualy or mechanically excavation and earth work in any type of soil, replacement of minor fitting such as sockets, union, threading, screwing etcto make joint leak proof compete all as specified and directed.

Supply and fixing in replacement of DOL starter suitable for 7.5 HP 3 phase, 415 volts pumping set Make Havells Cat Pt NoIHSDOAK1LA(Three phase DOL ) or equivalent complete all as specified and directed.

Supply and fixing in replacement of automatic Star Delta starter suitable for 20 HP pumping set 3 phase, 415 volts Make Havells Cat Pt NoIHSDOAK1LA(Three phase ASD ) or equivalent complete all as specified and directed.

Supply including mixing Calcium hypo chloride Granular in sealed container of 45 Kg as per requirement on daily basis complete all as specified and directed.

Supply Only Trichlorolosocynauric Acid 90% (TCCA) in Granual Form, complete all as specified and directed.

Supply Only Alum crystel super quality complete all as specified and directed.

Supply Only Dilute HCL ( hydrochloric acid).

Supply Only Copper sulphate CuSO4 (Neela Thotha).

Supply & fixing in repair, 80mm bore galvanized iron water tubing medium grade, jointing and testing in trenches/floor/wall,including provision of all necessary steel fittings/ accessories complete all as specified and directed.

Supply & fixing in repair, 50mm bore galvanized iron water tubing medium grade, jointing and testing in trenches/floor/wall,including provision of all necessary steel fittings/ accessories complete all as specified and directed.

Supply & fixing in repair, 40mm bore galvanized iron water tubing medium grade, jointing and testing in trenches/floor/wall,including provision of all necessary steel fittings/ accessories complete all as specified and directed.

Supply & fixing in repair, 25mm bore galvanized iron water tubing medium grade, jointing and testing in trenches/floor/wall,including provision of all necessary steel fittings/ accessories complete all as specified and directed.

Supply & fixing in repair, 20mm bore galvanized iron water tubing medium grade, jointing and testing in trenches/floor/wall,including provision of all necessary steel fittings/ accessories complete all as specified and directed.

Supplying ,laying, jointing & testing in trenches in repair DI pipe (K7) 100 mm bore with spigot and socketed ends centrifugally cast (spun cast) and including of rubber tyton joints complete all as specified and directed by Engineer-in-Charge for the following size:- Note :-(i) Earth work and CI specials/fittings of the pipes shall be measured and paid for separately under appropriate item of Schedule `A' (ii) Joints of the pipes shall be included in the item quated rates measured and paid for separately under appropriate item of Schedule `A'.

Supply & fixing in repair 200 mm bore , cast iron sluice valve of class PN-1 conforming to IS-14846 of 2000 both ends flanged with iron wheel head and stainless steel spindle, long body type,jointing and testing, ISI Marked, of approved quality complete all as specified and directed.

Supply & fixing in repair 150 mm bore , cast iron sluice valve of class PN-1 conforming to IS-14846 of 2000 both ends flanged with iron wheel head and stainless steel spindle, long body type,jointing and testing, ISI Marked, of approved quality complete all as specified and directed.

Supply & fixing in repair 100 mm bore , cast iron sluice valve of class PN-1 conforming to IS-14846 of 2000 both ends flanged with iron wheel head and stainless steel spindle, long body type,jointing and testing, ISI Marked, of approved quality complete all as specified and directed.

Supply & fixing in repair 80 mm bore , cast iron sluice valve of class PN-1 conforming to IS-14846 of 2000 both ends flanged with iron wheel head and stainless steel spindle, long body type,jointing and testing, ISI Marked, of approved quality complete all as specified and directed.

Supply& fixing in repair ISI Marked, of approved quality, cast iron non return valve 100 mm bore, both ends flanged jointed and tested complete all as specified and directed.

Supply & fixing in repair 40 mm bore gun metal globe/gate valve with iron wheel head, both ends screwed for iron pipe , jointing and testing ISI Marked approved quality complete all as specified and directed.

Supply & fixing in repair 25 mm bore gun metal globe/gate valve with iron wheel head, both ends screwed for iron pipe , jointing and testing ISI Marked approved quality complete all as specified and directed.

Supply & fixing in repair 20 mm bore gun metal globe/gate valve with iron wheel head, both ends screwed for iron pipe , jointing and testing ISI Marked approved quality complete all as specified and directed.

Material and labour for run lead joints including cutting properly for 100 mm bore CI pipes/fittings etc complete all as specified and directed.

Dismantling and taking down including Material and labour for run lead joints including cutting properly for 100 mm bore CI pipes/fittings etc complete all as specified and directed.

Dismantling and taking down including Material and labour for "D" joint made out of CI collar and rubber ring for 100 mm bore of CI/GI pipes complete all as specified and directed.

Dismantling and taking down including Material and labour for "D" joint made out of CI collar and rubber ring for 80 mm bore of CI/GI pipes complete all as specified and directed.

Dismantling and taking down including Material and labour for "D" joint made out of CI collar and rubber ring for 50 mm bore of CI/GI pipes complete all as specified and directed.

Dismantling of defective motors/other eqpts of any type and any capacity from Pumping set including transpotation to civil workshop for repairing,overhauling including M& L for rewinding (copper) complete with insulation, varnishing etc including dismantling and re-fixing to match with the existing original winding etc complete all as specified and directed.

Draining out water from OHT by operating wash out valve ,Cleaning of over head tank (staging from 6 meter to 18 Meter) (inside) by scraping with the help of hard brushes and physical cleaning of over head tank (reservoir) by descaling / brooming silt and other deposit in side (bottom of dome). collecting and taking them out with help of manual labour and depositing not exceeding 50mtr all as directed. Cleaning of inner surface of OHT by applying the bleaching powder solution (1:10) and left it for 1/2 hour for making surface algee/ bacteria free .clean the surface with water and drying it quick with the help of electric air blower. Applying two coat of thick quick drying lime wash on entire surface (inner) top and bottom including writting date of cleaning with white paint on back painted surface two places and painting of inner steel ladder of tank completeall as specified and directed.

Supply only BSPS Twisted Nylon Industrial Grade Multipurpose Line RoPE Alkali Chemical Weather Resistant Rope for Craft DIY Projects Towing, Dock Lines Heavy Load (Yellow, 20 mm Thick) complete all as specified and directed.

Supply only SPIRYFI 15.74 Foot Adjustable 2 Pcs Telescopic Pole with Deep Leaf Net for Cleaning of swimming pool complete all as specified and directed.

Supply only Flaner Premium Pool Brush Head Strong 18" Aluminium Swimming Pool Cleaning Brush Plastic Wet and Dry Brush (Blue) complete all as specified and directed.

Supplying and fixing in repair MCCB 630 Amps with sheet metal enclosure, MCCB ,4 Pole, 50Hz , Icu= 25 KA at 415 volts, with thermal magnetic release & Ics=100% Icu with adjustable over load setting (minimum 80% to 100%) complete all as specified and directed.

Supplying and fixing in repair MCCB 250 Amps with sheet metal enclosure, MCCB ,4 Pole, 50Hz , Icu= 25 KA at 415 volts, with thermal magnetic release & Ics=100% Icu with adjustable over load setting (minimum 80% to 100%) complete all as specified and directed.

Supplying and fixing in repair MCCB 160 Amps with sheet metal enclosure, MCCB ,4 Pole, 50Hz , Icu= 25 KA at 415 volts, with thermal magnetic release & Ics=100% Icu with adjustable over load setting (minimum 80% to 100%) complete all as specified and directed.

Supplying and fixing in repair MCCB 100 Amps with sheet metal enclosure, MCCB ,4 Pole, 50Hz , Icu= 25 KA at 415 volts, with thermal magnetic release & Ics=100% Icu with adjustable over load setting (minimum 80% to 100%) complete all as specified and directed.

Supply and fix in replacement of MCCB sheet metal Enclosure for upto 250 Amps.

Material and labour for checking and finding out pin point location of fault in HT underground cable 11 KV with the help of fault locating mobile machine complete all as specified and directed. Notes : (i) All T&P and other acceseries required for checking and finding of fault in cable shall be provided by theContractor (ii) Charges/rent of the fault locating mobile machine, operator, engineer, electricians etc shall be deemed to included rate quoted by Contractor. (iii) Checking and finding fault upto 03 places of same route of the cable will be considered as one Job

Supply and fix cable jointing kit suitable for 11000 Volts grade HT cable for outdoor termination cold shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 95 sqmm complete all as specified and directed.

Trimming/cutting/chopping of tree branches all around LT/HT over conductor upto two meter and removing excavated material n.exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr complete all as specified and directed.

Removing of old paint by removers scrubing from LT steel poles 9 meter long, cross arms clamps etc for painting and M &L for painting with one coat of superior quality aluminum paint on exposed surface of poles and street light bracket mounted on the poles,junction box etc and making black strip upto1.5 Mtr height from ground level and writing pole Nos etc. written on it with black synthetic enamel paint compete all as specified and directed.

Supply and fixing in repalacement LED Street light 70 Watt 230 V AC out-door type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, fixed to pole or wall of building with and suitable for Bracket made out of 32 mm dia GI light grade pipe, 1.20 m long bent to shape by cutting & welding as required & directed and fixed with two Nos of FI clamps 35x6 mm to be tightened with suitable size of bolts, nut and washers and including painted with two coat of aluminium paint over a coat of red oxide primer, and including connecting the fitting to electric source with & including twin twisted copper flexible wire of size 0.75 sqmm three core with suitable size flexible PVC conduit including all accessories and fixing arrangements for fixing the light fitting complete all as specified and directed.

Supply, fixing in replacement Outdoor type cubicle Bus Bar aluminium Chamber 400 Amps for three phases, 4 wire , CPRI approved IP-65 protection rupturing capacity at 415 volts , factory made having powder coating including earth work, necessary angle iron and PCC foundation of size, complete all as specified and directed.

Supply, fixing in replacement Outdoor type cubicle Bus Bar aluminium Chamber 250 Amps for three phases, 4 wire , CPRI approved IP-65 protection rupturing capacity at 415 volts , factory made having powder coating including earth work, necessary angle iron and PCC foundation of size, complete all as specified and directed.

Dewatering and cleanig of swimming pool ( Size of pool 50 mtr x 25 mtr x upto 18 ft depth ), balancing chamber, under ground drainage and inside overflow drainge of indide of swimming pool and removing all silt and other foreign materials including cleaning the tiles with suitable chemicals and keeping the tiles in wet condition and removing rubbish from the site complete all as specified and directed. Note :- All material such as chemical, brush, T & P shall be provided by the contractor and rates are included in quoted rates.

Dewatering and cleaning of diving tank ( appx size 3.0 mtr dia x 15.00 mtr deep ) , Trial tank and balancing chamber (UG sump) under ground drainage and inside overflow drainge and removing all silt and other foreign materials including cleaning the complete tiles with suitable chemicals and keeping the tiles in wet condition and removing rubbish from the site complete all as specified and directed. Note :- All material such as chemical, brush, T & P shall be provided by the contractor and rates are included in quoted rates.

Removing of old paint by removers scrubing from filter plant unit complete including pumping sets, pipes, fittings, sluice valves and pump foundation etc for painting and M &L for painting with one coat of superior quality synthetic paint with approved colours on exposed surface of plant etc and writing letters or figures (Block, Roman, Italic or Indian) n exc. 30 cm high and drawing stops, commas, short lines, dashes, hyphens, brackets etc. with synthetic enamel paint [SM/MES No., Capacity, Location etc.],

S & F cast/ductile iron fittings such as bends (any type, radious and angle) tapes any type (straight, bend, increasing, decreasing or double, socket etc) Tee pieces, single branch, Y junction, double branch, cross (all socket or socket and spigot) collar, caps and plugs etc suitable for pipe line upto 300 mm bore complete all as specified and directed.

Supply in replacement post top lantern LED type 40 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp.

Supply and fixing in replacement PVC insulated 6 sqmm copper conductor three core cable flat, 1100 volt grade for submerceble pumping set etc complete all as specified and directed.

Supply and lay in replacement Pipe cast Iron, S/S including specials, Class"B", 200mm(8") dia complete all as specified and directed.

Supply and lay in replacement Pipe cast Iron, S/S including specials, Class"B", 300mm(12") dia complete all as specified and directed.

Supply and fix in replacement of Cast Iron Valve, reflux, with by-pass Arrangement, 300 mm (12”) dia complete all as specified and directed.

S&F in replacement CI Y type stainer with SS 304 perforated screen 100mm dia complete all as specified and directed.

Supply and install in repair trolley mounted Suction Sweeper complete with motor, pump & starter, mounted on trolley including nylon rope, hose pipe float, nylon brush and rope includding rubber wheels, 1 HP Pump, 15 m, discharge 500 LPM, EVA Hose Pipe, 18 Inch Portable Vacuum Head, Trolly, Telescopic Rode 8+8 ft, 18-inch Curved Brushes, etc complete alongwith Swivel Cuff, Swimming Pool Suction Pipe (medium grade, 40 meter by 1-1/2 inch).

Supply, install, testing and commissioning in repair Non clog vertical submersible pumps with chrome steel impeller and cutter, non-clog to pass 40 mm size particles including guide rail and lifting , self priming, discharge 400 LPM, head range 25 mtr, 3 phase, 50 Hz, 415 volts, of capacity 3.0 HP/2.20 KW.

Supply and fix in replacement Monoblock pump set suitable for 415 V, 3 phase system having capacity 20 HP, 20 mtr head, 1400 LPM, complete all as specified and directed.

Supply of Heavy duty Chemical Dosing system plunger type suitable to inject solution upto 0-6 LPH working pressure 10 kg /cm2 comprising dosing pump coupled with three phase electric motor of capacity 0.5 HP,1440 RPM assembly with agitator in one motor , agitator with SS sweep blade duly FRP coated, FRP tank 150 ltrs capacity, complete unit mounted on heavy duty MS fabricated frame duly anticorrosive paint complete with Chemical grade PVC NRV. along with Control panel for Dosing Pump suitable for Model SSAPS/CDSPT/25 made of powder coated MS fabricated box consisting of LED indicator, digital Volt meter, Amp meter, single phase preventor, High voltage low voltage protection.

Supply only Digital PH meter tester.

Supply only Digital TDS meter tester.

Laying only XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 Sqmm 2 Core in trench/floor/on pole/wall complete all as specified and directed. (Note: Cable will be issued under Sch 'B')

Supply and laying XLPE insulated, armoured heavy duty electric cable with alumini-um conductor, 1100 volts grade, cross-sectional area 25 Sqmm 4 Core in trench/floor/on pole/wall complete all as specified and directed.

Supply and lay HDPE pipe medium class, ISI Marked double wall corrugated as in cable protection pipe of outer dia 40mm including all fittings complete all as specified and directed.

Supply ,installation, testing and commissioning in replacement of canopy headed HT 11K volt grade, 3 phase , AC, 50 cycle, feeder pillar box, factory made outdoor pedestal type double door, IP 65 protection with incoming and outgoing cable alloyfabricated out of 3.15 mm thick CRCA sheet with powder coated painting in side and outside of approved shade ,locking arrangement with 02 Nos 19mm dia lock of make Godrej with keys, two earthy terminal suitable cable gland for all incoming and outgoing cable grouting of feeder pillar box 30 cm above ground level by providing 90 cm long angle iron of size 50x50x6 mm welded on all the four comers embedded in PCC (1:2:4) using 20 mm graded stone agg upto 30 CM deep and 45 CM above from normal ground level complete all as specified and directed incl the following components:- (a) The panel will be having aluminium bus bar of size 50x10mm duly insulated with heat shrinkable sleeves with porcelain HT long post insulator 11 KV, Complete all as specified and directed.

Supply and fix in replacement wireless Water Level indicator fully automatic for 50000 gallons OHT at height 21 Mtr height Accuracy: High %. Complete all as specified and directed.

Supply and fixing of 100mm cast iron air release valve with drilled flanged ends, pressure rating (PN-1) and tamper proof with two air outlets with nuts, bolts and washer and conforming to IS-14845 complete all as specified and directed.

Supply, installation , Testing and Commissiong Intdoor type cubicle panel board inner cell made of 2mm thick and outer cell made of 3.15mm CRCA sheet for three phases, 4 wire, 415 Volts , 50 Hz with IP-54 protection rupturing capacity at 415 volts , factory made in an approved factory having seven tank treatment process for powder coating with thickness not less than 60 microns with paint shade RAL -7035 provided with suitable gasket to make it dust/vermin proof and mounted on PCC foundation of size as required or approved by manufacturers in PCC 1:3:6 Type C-2 , using 40 mm graded crushed stone aggregate as recommended by manufacturer or directed including earth work complete & general construction comprising of the following :-

(a) INNER SHELL :- Inner shell made out of 2 mm thick CRCA sheet duly compartmentalised and separation form 3(a) for each control gear, front & back openable double door system lockable /openable by key from both sides fancy locks , having louvers & air vent gasket fro natural flow of air, "U" type gasket shall be used to make the inner shell completely vermin proof & to accommodate incomer / outgoing MCCBs and electrical grade busbar with stand with heat shrinkable sleeves alonwith shrouds for joints & eath duly colour coded shall be mounted on suitable size "F" class insulator made of nonhygroscopic , noncumbustile , track resistance , high strength FRP/SMC/DMC material at an interval not less than 500 mm through out the length of the TPN busbar . The cubical incomer MCCB as well as out going shall have copper TPN extension links of current carrying capacity not less than 1.5 times the rated capacity of individual feeder, the extension links shall not be less than 300 mm long supported on suitable size "F" class insulator made of non hygroscopic , noncumbustile, track resistance , high strength FRP/SMC/DMC material having provision for termination of incomer and outgoing cables. All inter connections between the main busbar as well as outgoing feeder shall be arried out with TPN copper busbar of rating not less than 1.5 times rated capacity of individual outgoing feeder and should be insulated with heat shrinkable PVC sleeves.

All control wires shall be with 1.5 sqmm multistranded copper conductor and shall be properly bunched , tied, ferruled for proper identification and crimped with adequate size of copper lugs. The cubical shall have a bottom channel of size 75 x 40 mm duly coated with zinc metal coating having thickness not not less than 100 microns. A detachable predrilled gland plate of thickness 3.15 mm powder coated should be used at the bottom . The inner shell shall be of powder coated Siemens grey structtural RAL -7032 shade. An inspection lamp LED 5 watt with movable non ferrous chromium plated arm fitted on top side of inner shell shall be provided . The degree of protection for inner shell shall be IP-42 and carry the following controlls :-

Incoming : (a) Bus bar chamber comprising 4 Nos copper strip bus bars PVC insulated made of copper strip with current capacity 300 Amp with stand heat shrinkable sleeking alongwith shrouds for joints , PVC sheathed with colour coding . (b) Incommer MCCB, 4 pole having current ratings 160 Amps, AC 415 Volts, with Icu= 25 KA , Ics = 100% of Icu, with thermal magnetic release, complete with spreader links- Qty - 01 No (c) Onload Changeover switch 200 Amp - 01 No (c) Multifunctional digital panel meter with LCD display flush mounting type of size 96X96 mm, accuracy class 1, suitable for CTs with secondary current 5A, (d) MCCB, 4 pole having current ratings 100 Amps, AC 415 Volts, with Icu= 16 KA, Ics = 100% of Icu, with thermal magnetic release, complete with spreader links- Qty - 01 Nos (e) MCCB, 4 pole having current ratings 32 Amps, AC 415 Volts, with Icu= 16 KA, Ics = 100% of Icu, with thermal magnetic release, complete with spreader links- Qty - 07 Nos (f) DOL starter for 20 HP motor-02 Nos (g) DOL starter for 7.5 HP motor-02 Nos (h) Single Phase Preventer - 02 Nos

Materials and labour as in replacement for earthing complete with galvanized earth plate electrode 600 x 600 x6mm thick burried directly in ground vertically to a depth not less than 2.25 M below normal ground level ) with top edge of the plate not less than 1.50 M below normal ground level , connected to and including galvanized Iron Strip 32x6mm as earth lead soldered and riveted to earth plate by means of nuts, bolts, check nuts & washers, of galvanized iron or steel with connected to test point and testing on completion including 40mm GI light grade pipe for earth lead protection from earth point to earth plate, including provn adequate quantity of charcoal dust mixed with 35 % common salt to a packed thickness of not less than 32 cm in alternate layers of charcoal and salt on all sides of earth plate with 20mm bore medium grade GI Pipe for watering,GI check nut, funnel and wire mesh with and including all necessary excavation & earth work in soft/loose soil, returning filling in, removal of surplus soil to a distance 50 metre,,PCC 1:3:6 type C-1 as in earth pit, 40 mm thick RCC cover using cement concrete 1:2:4 type B-1 reinforced with & including 8 mm dia mild steel TMT bar @ 100 mm c/c Both way with suitable handle for lifting arrangement & including form work complete all as specified and shown in electrical plate No 3 of MES SSR Part I 2009 and as directed. NOTES:- (i) On testing, after completion of Job, if desired earth resistance is not obtained, the earthing shall be redone at without any extra cost by contractor.

Supply, laying & testing cable XLPE insulated, screened PVC bedded galvanised steel strip armoured HT electric power cable (heavy duty) 11000 volts grade with aluminum conductor11 KV (E) grade, cross sectional area 95 Sqmm 3 core as per IS-7098 suitable for earth system laid in trenches including taking out unserviceable /brunt HT cable of any type /rating, complete all as specified and as direcetd.

M&L and T&P for disconnecting HT/LT connection, shifting, installing, testing and commissioning of step down Outdoor type copper wound transformer of any capacity from one location to other location within the defence land complete all as specified and directed. Note : Cost of materials required for connecting, commissioning and testing of transformer shall be deemed to be included in quoted rate.

Sampling and testing of water for the conformation of Desirable / permissible limit of following requirement for Drinking water' as per IS:10500-1991 from Govt approved laboratory including transportation of water complete all as specified and directed (a) Bacterioligical requirements : Testing of coliform Organism / 100 ml. (b) Chemical requirements : Testing of colour hazen unit max odour taste turbidity NTU max, PH value, total hardness (as CaCo3) mg/lmax, iron (as FE) mg/L max. (c) Desorable Characteristics : Testing of dissolved solids mg/l max, Calcium (as CA mg/l max, magensium (as Mg/l max, Copper (as Cu mg/l max, Manganese (as Mn) mg/l max, Sulphate (as SO4) mg/l max, nitrate (as NO3) mg/l max, phenolic compound mg/l max, mercury (as Mg) mg/l max, Cadmium (as Cd) mg/l max, Selenium (as Se) mg/l max, Arsenic (as As) mg/l max, Cyanide (as CN) mg/l max, Lead (as Pb) mg/l max, Zinc (as An) mg/l max, Chromium (as Cr +) mg/l max, Mineral Oil mg/l max, complete all as specified and directed.

M/S SHARADA ASOCIATE

M/s KCL Engines and Machines

M/S VIDIT ENTERPRISES

Balaji Associates

m/s Agra Builder

3Krishna Enterprises