REPAIR TO GALVALUME SHEETS ROLLING SLIDING SHUTTER ALUMINIUM UPVC DOOR WINDOW OTHER MISC BR WORKS IN OTM ACCN OF COD UNDER AGE BR I OF GE NORTH DELHI CANTT10

Amount

Removing of existing water proofing membrane, damage plaster, vegitation/plants, PCC, Tar-felt, loose particles and all foreign materials over the roof and shifting the debris from site to out-side area as directed. Cleaning the surface & removing of dust, existing paints from wall & roof surface, finding visible crack, Making V - groove by machine on crack area, including providing & applying polymer bonding agent (1:2) & filling those grooves by modified cement & sand mortar (1:4) with WPM liquid (5% by wt. of cement) complete all as specified and directed.

Waterproofing coating-providing & applying 1st coat WPM with brush/roller after mixing with cement at 1:1.5 (1 part of WPM and 1.5 part of cement & 2nd coat with an interval of 10 to 12 hrs by brush or roller to get average thickness of 1.5mm. The system will be allowed to air cure for 7 days covering including parapet both side wall. Note - The work is to be executed through authorised applicator.

Hacking out old broken glass (any thickness , size, quality, or description) from metal frame glazed with putty or fixed with beads/ clips complete all as specified and directed.

S&F rough cast, wired fibre glass sheet exc 6mm thick but n.exc 6.40mm thick fixed with flat iron and nut bolts in squre/rectangle & as required exc 0.75sqm but n.exc 1.00sqm in each pane wixed with necessary securing arragement as previus at height upto 15m complete all as speccified and direccted.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete(steel or wooden metal) all as specified.

Demolition of cement concrete (reinforced) roof, floors(other than ground floor, beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided.

Dismantling timber scantlings 40 sq. cm and over in section, in frame work at any position complete all as specified and directed.

S&F structural steel work for rolled sections as in main and cross beams, hips, jacks, rafters, purlins, runnings, rails and guides for sliding doors fixed with angles, cleats or other conneccting plates grade FE-410-W at working height 15m complete all as specified and directed.

M&L two coats of synthetic enamel paint on old steel surfaces of any description, exc 10 Cms in width or girth, including preparation of surfaces, complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semicorrugated, etc) sheets in roof coverings complete all as specified and directed.

S&F prepainted galvalume aluminium zinc coating GI based corrugated steel 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in roof complete all as specified and directed.

Dismantling of plain or corrugated steel/ fibre sheeting of any guage as in roof covering including ridges/gutters etc of any description straight or curved at height upto 15m complete all as specified and directed.

S&F 0.50mm plain, Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet galvanised, mild steel sheeting, in ridges, hips, valley gutter, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 and welded or soldered joints are provided as requried complete all as specified and directed.

S&F 2mm thick PGI sheet having 275gm of zink coating per sqm both sides in valley gutter, dripper,or as rain water pipe, straight flashing with 100mm overlap made to required shape & size includingwelding or revetting and fixed in position and working height upto 15m complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fitting, head, shoes, bend, swan-nacks etc., including cleaning or refixing or removal to store complete all as specified and directed.

S&F steel rolling shutters in repair, gear operated type with bevel gear box and crank handle without ball bearing as specified including top covers anchoring rod, hasp & staple and one shop coat of red oxide primer and errected in position complete thickness of laths 1.25mm complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 Square Metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish without any extra cost to Govt ), complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfast shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed.

S&F powder coated aluminium window made of aluminium tubular frame and double shutter (galzed and gange shutter) of section 63.50 x 38.10 x 1.60mm and style fixed openable horizontal and vertical member of aluminium, beading rubber gasket and aluminium fittings such as tower bolts, handle stay and rod and hinges 5mm thick glass etc complete all as specified and directed. Note:- Fixtures / fittings of window shutter including glass and wire mesh is deemed to be included in the quoted rate against this item.

S&F in repairs powder coated aluminium anodised hollow section door frame and shutter (swing type) openable with top rail, style of section 47.62 x 44.45 x 1.60mm and lock rail, bottom rail of size 101 x 44.5 x 1.6mm including jointing cleats, snap beading, glass/ nova pan board, gasket for fixing glass/board in panel including 1 door closer (hardwyn), 2 nos of size dish type handle, hinges, tower bolts -02 Nos 150mm in each leaf and screws complete all as specified. Note: Fixtures / fittings including glass of door shutter is deemed to be included in the quoted rate against this item.

S&F anodised aluminum alloy powder coated standard hollow section for window two tracks including aluminum frame/ chowkhat with following specification including anodised aluminum snap beading, channels, 5mm thick tinted glass, glazing clips, joint cleats, rubber gasket etc and other accessories complete all as specified and directed. (a) Frame of section :- 83.50mm x 44.50mm x 1.60mm thickness. (b) Sliding window section (channel):-40mm x 18mm of 1.20mm thickness with locking arrangement. Note:- (1) The rate also included the cost of cutting, waste and making good disturbed surface matching with existing surface and finish as directed. 2) Minimum thickness of powder coating shall be 50 micron. (3) Make for PVC sheet :- Sintex, Rajshree, Tata.

S&F brass mortice lock 4-lever vertical type, size 100mm all as specified.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description, exc 10 Cms in width or girth, including preparation of surfaces, complete all as specified and directed.

Removing foreign materials i.e silt, sludge, soil from valley gutters, in any pipe of any dia in any position without disturbing the structure of valley gutter & sheets, working height upto15m and thrown away from MOD land complete all as specified and directed.

M&L WPC acoustic wall paneling for indoor/outdoor wall 100% nontoxic, non feraldelyers, water proof, termite proof anti UV using necessary SS clip/fixing arrangement/incl taking down old pre laminated particle board complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls/ceiling etc including raking out joints, hacking for key, scrubing down with water etc complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stone work and precast articles, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan on exceeding 6m mean radius, using old size brick, built in cement mortar 1:6, complete all as specified and directed.

M&L for rendering 15mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement all as specified.

M&L for rendering 15mm thick on brick work or concrete surface in cement mortar 1:4 including water proofing compound finished even and smooth without using extra cement all as specified.

M&L for rendering 10mm thick on brick or concrete surface as in ceiling in cement mortar 1:3 finished even and smooth without using extra cement all as specified.

M&L preparation of newly plastered surface on walls and applying two coat of oil bound distemper over 2mm thick wall care putty complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed.

M&L for preparing newly plastered surfaces of ceilling and applying three coats of white wash complete all as specified and directed.

M&L for 3D block/river rock/cliff stone or as approved by Engr-in-charge, as in dado/vertical surface of size 300mm x 600mm x 8 to10mm thick set and jointed in neat cement slurry and pointed in coloured cement to match the surface including backing coat of cement mortar in CM 1:4 etc including dismantling floor, hearth or wall tiling including cement mortar bedding and also backing, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Providing and fixing 4mm thick aluminium composite panel (ACP) exterior grade (0.5mm PVDF coated Aluminium skin on top & bottom plus 3mm thick polyethylene core) on/all-round RCC/Brick column/ wall/ Fascia's/ M.S. section/ Aluminium section structure/ dead walls/under side sky light upto all height in required colour/pattern & panel size as (Area of panel shall not more than 0.60Sqm as per drawing fixed on aluminium extruded standard tubular section of size 38 x 25 x 1.6mm of approved make (Jindal/ Hindalco/ Indalco) conforming to IS;733 and IS; 1285, fixed at 600m center to center with rawl plugs and screws or with fixing clips or with expansion hold fasteners Aluminium sections shall be smooth rust free straight mitred and jointed mechanically wherever required including cleat angle CP brass/stainless steel screws, with 12mm (wide) x 20mm (deep) groove in joints or panels including filling the joints with weather silicon sealant of Dow coming 789 or equivalent of approved colour inacp ACP, weather sealant structural sealant/adhesive tape, masking tap, primer/ gasket/ foam/ scaffolding/ cluding 10mm dia backer rod, The rate shall include cost of ACP Panel, subframe of aluminium section for fixing of ACP, weather sealant structural sealant/adhesive tape, masking tape primer/ gasket/ foam/ scaffolding/ Aluminium cleats with screws complete including making openings as required at site like electical fittings, recess for pipe etc, all necessary tools and plants, scaffolding and as per manufacturer's technical specifications, including dismantling of old sheet complete and as per the direction of the Engr-in-Charge (Surface area of aluminium composite panel shall be measured for payment.

ANSH VANSH CONSTRUCTION COMPANY

V r traders

P.H. CONSTRUCTION CO.

M/s Durga Traders

Rohan Construction Company

VIJAY KUMAR GUPTA

V M CONSTRUCTION

Keshav Brothers