REPAIR TO INTERNAL WATER SUPPLY, CHAJJA, BALCONY, FACIA AND OTHER MISC WORKS UNDER AGE B/R (P) AT ITARANA ALWAR

Amount

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level.) & removing unserviceable materials in low laying area, complete, all as directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.

Demolition of brick/stone masonry built in cement/lime mortar of any mix and stacking serviceable stones aside for reuse & removing unserviceable materials in low laying area, complete, all as directed by Engr-in-Charge.

M&L for PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in flooring or levelling coarse 25mm thick complete all as specified & as directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L 15mm thick plaster in CM 1:4 mixed with water proofing compound @ 3% by weight of cement including fair and even & smooth without using extra cement all as directed. (WPC shall be measured & apid separately)

Supply only integral water proofing compound (ISI marked).

M&L rendering 15mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified.

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

M&L glazed ceramic tiles (Ist quality) (coloured) 300mm x 200mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar 1:4 complete all as specified and as directed.

Material and labour glazed ceramic tiles (Ist quality) (coloured) 300mm x 450mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for coloured non skid ceramic tiles 7 to 8mm thick (square/rectangular) (Ist quality) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for vitrified ceramic tiles 10mm thick (square/rectangular) polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M&L for vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L 20 to 25mm thick Granite (of any type) slab of approved shade as in flooring, platform etc, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing (mirror polish i.e. full granite polish as per local trade practice) over & including 20mm thick screed bed (bedding layer) in CM 1:6 all as specified & directed.

Taking up or down 15mm bore steel tubing and connection incl cleaning for refixing or removal to store.

Taking up or down 20mm bore steel tubing and connection incl cleaning for refixing or removal to store.

Taking up or down 25mm bore steel tubing and connection incl cleaning for refixing or removal to store.

M&L galvanised steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

M&L galvanised steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

M&L galvanised steel water tubing medium grade of 25mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

Refixing old steel tubing and connection in new or old position (wall, ceiling, floor etc) of 15mm bore of pipe.

Refixing old steel tubing and connection in new or old position (wall, ceiling, floor etc) of 20mm bore of pipe.

S&F in repairs 15 mm bore bib tap, cast copper alloy with aerating device operations, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule.

S&F in repairs 15mm bore fancy type pillar tap with aerating device operations, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes.& fly nuts, screwed for iron pipes.

S&F in repairs 15 mm bore stop valve, cast copper alloy, any type, chromium plated, scewed down, high pressure with capstan head, screwed both ends for iron pipe or for union complete all as specified and directed.

S&F in repairs 15 mm bore stop valve, cast copper alloy, fancy type, chromium plated, scewed down, high pressure with capstan head, screwed both ends for iron pipe or for union complete all as specified and directed.

S&F in repairs 15mm bore Two way Angle valve chromium plated screwed plated screwed down,high pressure with capstan heads screwed both ends for iron pipe or for union.

S&F in repairs 15 mm bore fancy type long body bib tap with aerating device operations, half turn, with wall flange, cast copper alloy with capstan heads, chromium plated, screwed for iron pipe or for brass ferrule, complete all as specified & as directed.

S&F wall mixer chromium plated (3 in -1) with arrangement for both telephonic shower and overhead shower with 220 mm max long bend pipe with hand shower of size 100 x 55 mm with 130 mm long arm & 1.2 m house pipe complete all as specified & directed. Make : Cera Cat No CL-113 & CG 425 or equivalent of PARRYWARE / JAQUAR / SOMANY / HINDWARE / PRAYAG as approved by GE.

S&F as in repairs brass cockswith crutch or butterfly handle, screwed down for 20mm bore pipe. complete all as specified.

S&F in repair Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 20mm bore.

S&F in repair chromium plated brass shower rose screwed for 15 mm bore GI pipe, 125 mm bore

Supply and fixing in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

S&F 32/38/40 mm dia PVC flexible waste pipe 80cm long with socket for union, for WHB/urinal/sink complete all as specified.

S&F waste coupling of CP (half or full threaded) suitable for WHB/Sink, bore dia of discharge pipe 32mm (Minimum weight 120gms).

S&F in repair Flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern

Supply and fixing in repairs PVC internal fittings (Kit) complete set for low level flushing cistern tank to make the existing cistern functional complete all as specified.

Supply and fixing in repairs equilibrium float valve suitable for low level flushing cistern tank complete all as specified.

Supply and fixing PVC connection 600 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

Supply and fixing PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F in repairs 32mm bore Brass chromium plated bottle trap for wash basin with inlet and outlet screwed for pipe or connections including necessary packing, union and cap complete all as specified.

S&F in repairs Jet spray chromium plated brass for EWC with & including PVC connection 900 mm long suitable for 15 mm bore GI pipe with PTMT nut & nipple complete.

S&F in repairs health faucet, brass chromium plated, including fixing to steel pipe of 15mm bore or union complete all as specified.

S&F in repairs Plastic water closet seat cover, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified.

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

S&F in repairs vitreous china wash hand basin with pedestal, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

S&F in repairs vitreous china wash down water closet (Pedestal pattern EWC), coloured, floor mounted coupled closet, including connection to drain (or outgoing pipe), anti-sypohonage pipe etc, with & including WC seat cover coloured closed pattern with flat bottom and cover, vitreous china symphonic action type twin flush flushing cistern of 10 litre capacity with lid, necessary fittings complete all as specified & as directed. Make : “Casade NXT Popular” of Parryware {Cat Part No C0286 (Closet), C0711 (Cistern), C2054 (Cistern Lid), E8300 (Hush Seat Cover) & E8016 (Fittings)} or equivalent of HINDWARE / CERA / JOHNSON / NEYVELI CERAMICS (NEYCER) / JAQUAR / KHODIYAR / PRAYAG

S&F in repair brass chromium plated Towel Rack 600mm Long with Lower Hangers (Cat Part No ACN-1181N of make - Jaquar or equivalent of PARRYWARE / SOMANY / HINDWARE / PRAYAG as approved by GE.

S&F in repairs vitreous china counter top basin size 450 x 525 x 195 mm shape ovel of Jaquar Cat No CNS-WHT-601 or equivalent of PARRYWARE / JAQUAR / SOMANY / HINDWARE / PRAYAG as approved by GE including 32 mm CP waste coupling & PVC flexible waste pipe of 90 cm long complete all as specified & directed.

S&F as in repair CP brass nipple/Leg left/Right spindle/phase for connection of wall mixture with GI pipe including CP nut all as specified & as directed.

S&F in repairs plastic lid cover including locking arrangement for existing 500/1000/2000 Litre capacity rotational moulded polyethylene water storage tanks cylindrical vertical complete all as specified and as directed. Note :- Cover shall be provided of make as per existing water tank.

S&F as in repairs brass spindles for any size brass or CP brass bib cocks/stop cocks complete all as specified.

S&F in repairs 15mm bore, GI socket, Hex Nipple, GI Nipple 75mm, Nipple 100mm, NIPPLE, 150MM, gi Tee, GI Tee,GI Elbow, GI reducer(15mmx20mm), (GI reducer (15mmx25mm)

S&F in repairs 15mm bore, GI Union, GI Tank Nipple

S&F in repairs 20mm bore, GI Socket, Hex Nipple, GI Nipple75mm,Nipple 100mm, Nipple 150mm, GI Tee, GI Elbow, GI reducer (15mmx20mm), GI reducer (15mmx25mm)

S&F in repairs 20mm bore GI Union, GI Tank Nipple.

M&L for repairs to existing 15mm bore bib tap/stop cock etc cast copper alloy by replacing brass jumper assembly of bib tap matching with existing and fixed in old/new location all as directed

Checking and attending to complaints of water leakage from bib taps,stop cock ,pillar taps, flushing cisterns, wash hand basins, urinal, wall mixer/basin mixer ,angle valve ,concealed valve,shower rose , health faucet & jet , float valve , of any type & size or any other water supply fittings/fixtures incorporated in plumbing works not mentioned here in before used any where in the bldgs which is causing obstruction to water supply in area,& requires plumbing including carrying out minor repairs such as replacement of washers, check nuts, tightening of fittings of flushing cistern or any other repair not mentioned herein before etc using petty materials like washers, thread(soot),Teflon tape,M-Seal, screws(any size), nails(any size) or any other material not mentioned here in before to make water supply/plumbing lines & fiittings/fixtures functional and leak proof to the satisfaction of the occupants/users under the jurisdiction of AGE B/R - P Note: i) The rate of above mentioned item incorporates use of any materials & equipment used for completing the complaints on time to the satisfaction users/occupants (ii) Contractor or his authorised representative shall collect such type of complaints mentioned here in above from B/R-P complaint cell at 8.30 AM on daily basis except Sunday & Holiday & submit the completion of complaints on the next day duly signed by the users/occupants. No extra payment shall be made on account of collection of complaint and submission of complaints . (iii) Complaints must be completed with in 24 hrs without any fail otherwise recovery shall be made double the market rate to the contractor. (iv) Any items required to be replaced shall be paid under respective items and in that case this items shall not be measured and paid.That complaint should also be completed within 24 Hrs without fail.

Disconnecting & dewatering of PVC overhead taks, scrubbing the inner surfaces, cleaning & removing all scales, dirt etc from mouth of circulating pipes, washing the tanks with fresh water and disinfecting the same by flushing with liquid chlorine or any other equivalent chemical, reconnecting & refiing in position after cleaning for tank capacity not exc 500 ltrs each including marking the date of cleaning with white paint and stencil all as required & directed. Note: (i) Cleaning shall be done through wash out pipe by marking suitable arrangement to the outlet pipe such as cutting of the pipe providing short piece of pipe fitting and union coupling etc where the wash out pipe are not existing. The dirt etc shall not be allowed to enter the water supply system. (ii) Completion of complaints shall be carried out within stipulated time period to the satisfaction of Engr-in-charge & users/occupants. (iii)The quoted rates are include items incorporates use of any material for completing the complaints to the satisfaction of user/occupants.

All as per serial item No 64.00 here-in-above but exc 500 ltr and not exc 1000 ltrs capacity.

Dismantling water tank of capacity exc 250 litres & not exc 500 litres of any description and removing from site complete all as directed.

Dismantling water tank of capacity exc 500 litres & not exc 1000 litres of any description and removing from site complete all as directed.

Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I

Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I

Supply and fixing in repair Ball valves, high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball, screwed for iron pipe 20mm dia (minimum weight 210 gms) complete all as specified and as directed.

S&F in repair sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 915mm x 460 mm with bowl size 410mm x 330mm x160 mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete all as specified and directed.

M&L for PVC of 32mm bore and 500mm long as in spout pipe from sunken floor to external surfaces including cutting brick wall/RCC/PCC and making good in CM 1:3 complete to walls and ceilings or laid in floors.

Material and labour preparation of newly plastered/asbestos cement surfaces of ceilings & applying three coats of white wash complete all as specified.

M&L brooming down old decorated plastered/asbestos cement surfaces of ceilings & applying two coats of white wash complete all as specified.

Material and labour preparation of newly plastered surface of walls & applying two coats of cement base paint over a coat of primer complete all as specified.

M&L brooming down old decorated surfaces of walls, plastered including cornices, pilasters etc and applying two coats of white wash complete all as specified.

Material and labour preparation of newly plastered surface of walls & applying three coats of white wash complete all as specified.

M&L preparation of old decorated plastered surfaces of walls and applying one coat of cement base paint of approved shade/tint complete all as specified & as directed.

Treatement for sunken portion is as follows :- (i) Demolition of lean concrete and other type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. (ii) M&L for providing 12 mm dia holes of 40mm deep @2.00m c/c at junction of beams and columns as co-ordinal points for inserting/pouring cement slurry by pressure grouting for sunken floors of toilet , includind sealing the holes with CM 1:3, all as specified and as directed by Engineer - in - Charge. (iii) M&L for water proofing plaster for sunken portion in CM 1:3, 20 mm thick in two coats with water proofing compound at the rate of 2% by weight of cement and finishing the surface even and smooth without using extra cement. (WPC will be measured and paid seperately). (contd....)contd....) (iv) M&L for applyin evenly two coats of industrial bitumen 85/25 at the rate of 1.20 Kg/Sqm in each coat over vertical surfaces and floors of sunken floors of toilet including cleaning of surfaces. (v) M&L for PCC 1:7:12 type D2 using 40 mm graded stone aggregate as in filling (sunken portion). etc. (vi) M&L for PCC 1:2:4 type B0 using 12.50 mm graded stone aggregate, mixed with WPC @ 2% by wt. of cement, as sub base, 75mm thick. (WPC will be measured and paid separately.) on top (vii) M&L for plastering in CM 1:4, 15 mm thick with water proofing compound at the rate of 2% by weight of cement and finishing the surface seven and fair.(WPC will be measured and paid seperately) (contd....)(contd.…) Note :- Above includes (a) Test again of water tightness by pounding for 72 hours & rectify defects if any till total elimination of defect. (b) The sunken portion shall be tested for leakage / seepage / dampness by pounding with water for 72 hours. In case any defect is noticed the portion shall be grouted with cement slurry mixed with suitable chemical & tested again. The process of grouting and testing shall be repeated till leakage / seepage / dampness is eliminated. (c) Horizontal flat area to be measured.

Demolition of existing lime concrete/PCC padding, roof treatment of any thickness laid over RCC roof/chajja etc., removing complete layer of bitumen under concrete/PCC padding, cleaning and washing of roof with water to remove dust etc as preparation to receive treatment all as directed by Engineer-in-charge.

M&L for padding with PCC 1:2:4, type B0 (using 12.50 mm graded crushed stone aggregate ) as in padding and levelling course, on roof and floor finished even & smooth w/o using extra cement.

M&L for 15mm thick plaster over top of roof slab/chajjas in CM 1:4 mixed with water proofing compound @ 3% by weight of cement or as per manufacturer’s instructions, finished even and smooth without using extra cement all as directed. Note : - Supply only water proofing compound shall be measured and paid for separately.

M&L PCC 1:3:6 type C-1, using 20mm graded stone aggregate as in base of tanks including finishing even and smooth complete all as specified.

S&F 75mm bore UPVC (SWR) ISI marked pipes single socketed in any length with rubber ring joints / solvent cement joints laid in trenches or in floors complete all as specified including dismantling & taking out old unserviceable 75mm bore PVC pipe with fitting

S&F 110mm bore UPVC (SWR) ISI marked pipes single socketed in any length with rubber ring joints / solvent cement joints laid in trenches or in floors complete all as specified including dismantling & taking out old unserviceable 110mm bore PVC pipe with fitting

S&F 75mm bore UPVC (SWR) ISI marked pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified including demolition & breaking up 75mm bore PVC pipe with fittings.

S&F 110mm bore UPVC (SWR) ISI marked pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified including demolition & breaking up 110mm bore PVC pipe with fittings.

S&F UPVC (SWR) ISI marked floor trap dia of outlet 75mm, with PTMT grating including jointing with solvent cement including taking out old unserviceable trap.

Supply and fixing in repair 75 mm bore UPVC (SWR) ISI marked bends any radius complete all as specified.

S&F in repair 75 mm bore UPVC (SWR) ISI marked bends any radius provided with access door complete all as specified.

Supply and fixing in repair 110 mm bore UPVC (SWR) ISI marked bends any radius complete all as specified.

S&F in repair 110 mm bore UPVC (SWR) ISI marked bends any radius provided with access door complete all as specified.

S&F in repair 75mm bore UPVC (SWR) ISI marked branch piece, single (single ‘Y’) equal or unequal with access door.

S&F in repair 110 mm bore UPVC (SWR) ISI marked single branch piece(single 'T' ) equal or unequal provided with access door complete all as specified.

S&F in repair 110 mm bore UPVC (SWR) ISI marked single branch piece(Double 'T' ) equal or unequal provided with access door complete all as specified.

S&F in repair 75 mm bore UPVC (SWR) ISI marked single branch piece(single 'T' ) equal or unequal provided with access door complete all as specified.

S&F in repair 75 mm bore UPVC (SWR) ISI marked single branch piece(Double 'T' ) equal or unequal provided with access door complete all as specified.

Supply and fixing in repair 110 mm bore UPVC (SWR) ISI marked vent cowl complete all as specified.

M&L for taking down and removal of loose / disintegrated old concrete / plaster and applying 10mm thick bonding coat of modified styrene butadiene emulsion (SBR Bonding agent i.e. Nitobond SBR 45) in proportion 1 (Nitobond SBR 45) : 1(water) : 3 (OPC) by volume with the brushes etc to bind New Cement plaster/ polymer Modified plaster/ concrete/ screed concrete with old surface etc complete.

M&L applying 15mm thick plaster with polymer modified mortar fortified with SBR (Nitobond SBR 45 ) in proportion 1:3 by weight 5 litres Nit bond SBR 45 to added to 50 KG Cement with 13 litre water addition, finished surface to match with existing adjoining surface of ceiling, beams and alike complete.

M&L and applying two or more coats of 2 component zinc based epoxy rust preventer (Nitozinc Primer-M) on corroded reinforcement after cleaning and removing the rust from corroded reinforcement with the help of wire brush and treating it with rust remover (Reebaklens RR) including thoroughly cleaning washing air blowing brushing etc complete Note : Qty of Zinc based epoxy rust prevent or only shall be taken into account for payment purpose on the basis of actual consumption.

M&L cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified & as directed.

M&L cutting out cracks to V-section in existing roofs or terracing, cleaning out, and solidly with a hot mixer bitumen and clean dry sand 1:1 (by weight) etc. complete all as specified & as directed.

M&L wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashings and junction of parapets, etc., and surface painting with a layer of blown bitumen of any penetration applied hot @ 1.7 kg per sqm blinded with grit or pea size gravel @ 0.006 Cum per sqm, and lightly tampered (area of flashings etc shall be added to the roof area) complete all as specified & as directed.

M&L for mild steel TMT bars 10mm dia & over cut to length bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and bending with and including MS wire (annealed) not less than 0.9 mm dia, complete, all as specified and directed.

All as per serial item No. 105.00 here-in-above but 6 to 8mm dia.

M&L for 15mm thick cement mortar plaster in CM 1: 4 proportion (added with integral water proofing compound last X421 IC on brick /Cement concrete /RCC Work or any type of finish including removal of loose / disintegrated old concrete /plaster and surface and preparation of surfeace etc complete all as specified and directed by Engr-in-Charge

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work (reinforcement cut as required to facilitate demolition) all as specified & as directed.

M&L reinforced cement concrete (nominal mix)1:2:4 type B1 using 20mm graded stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L reinforced cement concrete (nominal mix) 1:2:4 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in chajjas and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete.

M&L for formwork to flat surfaces of chajjas, chullah hoods, troughs and similar items including edges for rough finished surfaces.

M&L for formwork to edges of concrete flats, roofs, floors etc not exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for rough finished surfaces.

Deployment of Manpower with material as on requirement basis for carriying out different type of Masonry work such as plaster work (upto 5.0 sqm at one place), repair/replacement of broken tiles fixed in any position (upto 2.0 sqm at one place), repair of brick work (upto 0.5 cum at one place), repair of PCC/hard stand (upto 0.25 cum at one place), repair of manholes, valve pits, pointing of roofs, repairs to jambs of doors, windows, coping and benching of chajjas etc, of various Md Accn & OTM Accn under the AOR of AGE B/R (P) to entire satisfaction of Engineer-in-Charge and as directed. NOTE:- 1. All the bldg materials which are required to carry out necessary repair work(s), cost of transportation/handling of bldg materials and the labour element is deemed to be inclusive in quoted rates. No claim(s) by contractor in this effect will entertaind at any stage. 2. All the repair wks receive/assigned on a perticuler day will be addressed and completed on that perticuler day only (upto 1800 hrs) or any stipulated time given by the Engineer-in-Eharge, recovery shall be made double the market rate to the contractor.

M&L for cutting into old masonry walls built in cement mortar to form toothings for and bonding in new brick or stone work including making good in cement mortar (1:6) complete all as specified & as directed.

M&L for 15mm thick rendering in two layer on fair faces of brick masonry or concrete surfaces of walls consisting of 1st layer of 10mm thick plaster in CM 1:6 and 2nd layer (setting coat or top layer) of 5 mm thick plaster in CM 1:4 mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished fair & even, complete, all as specified. Note : - Supply only water proofing compound shall be measured and paid for separately.

M&L for Priming surfaces and applying normal treatment (for moderate conditions), using glass fibre base bitumen felt, grade 2 all as specified and directed.

M&L for Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified & as directed.

Raking out joints/pointing to random rubble or polygonal rubble uncoursed or brought up to courses in cement /lime mortar.

M&L walling of random rubble, uncoursed, well bonded, bedded and solidly hearted stone masonry built in cement mortar 1:6 all as specified and as directed.

All as per description of serial item No. 121.00 above but except stone.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints with maximum depression on face from straight edge held against the dressed surface n. exc 20 mm in lime or sand stone work.

M&L brick work with subclass 'B' old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified.

Material and labour brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.

M&L for machine cut Kota stone slab flooring 20 to 25mm thick laid over & including screed bed or bedding layer of 15mm thick in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified.

M&L machine cut Kota stone slab 10 to 15mm thick , as in riser of step, skirting, dado etc. laid over & including screed bed or bedding layer of 10mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified.

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling and mass concrete.

M&L for 75 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for 50mm thick PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in flooring, finished even and smooth with using extra cement complete all as specified & as directed.

S&F glass dividing strips 3mm thick and 38mm wide & fixed in position as directed.

M&L for 40mm thick PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in flooring, finished even and smooth with using extra cement complete all as specified & as directed. Note : - Glass dividing strips shall be measured and paid for separately as “Supply only” under relevant item of this Schedule.

M&L for 50mm thick Sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, not exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4, complete.

M&L factory made 60mm thick machine pressed precast cement concrete interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and no pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as Specified & directed.

M&L precast cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in kerb block with plain fair faces, kneelers, apex stones, bed plates and the like including weathering, slightly rounded or chamfered angle throating, with plain or interlocking joints and setting in cement mortar 1:4, complete, all as directed.

M&L for machine cut Kota stone slab 40mm thick as in shelves & similar works, in single piece not exc 1.5m in length, fixed and jointed with grey cement set and pointed in cement mortar 1:4 including rubbing and mirror polishing (top side only and self finished bottom side) including cutting chases as required & making good to facings as original in cement mortar 1:4 for inserting stone slab shelves in stone/brick walls complete all as specified & as directed.

M&L for chequered cement concrete tiles 20cmx20cmx20mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment, complete all as specified and directed by Engr-in-Charge.

M&L precast cement concrete (1:2:4 type B0 using 12.5mm graded stone aggregate) louvers and jallies, 35mm thick (measured solid), including all mouldings but excluding frame, set in CM 1:4 all as specified & as directed.

M&L precast cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in pillar for fixing of jallies and setting in cement mortar 1:4, complete, all as directed.

Cutting openings through stone masonry walls for door, window and other openings or enlarging existing openings, etc., or cutting out defective masonry for underpinning including providing, fixing and removing, shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises.

M&L forming jambs, etc., to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, new work built in cement mortar 1:4 complete all as specified & as directed.

Material and labour preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L preparation of old decorated surfaces of walls by washing, rubbing down and stopping of distempered surfaces and applying one coat of oil emulsion distemper (OBD) of approved shade/tint all as specified & as directed.

M&L for preparation of new plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer on walls all as specified & as directed.

M&L for preparation of new plastered surfaces of ceilings and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer on walls all as specified & as directed.

M&L for 75 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 2 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L for padding with PCC 1:2:4, type B0 (using 12.5 mm graded crushed stone aggregate ) laid to a average thickness 50mm thick over roof slab etc as in levelling course, finished even & smooth w/o using extra cement.

S&F in repair factory made PVC shutter of 18 mm thickness consisting of panel of 18 mm thick celluca ply of density 600 Kg.cbm density with prelaminated sheet on one side cut in desired size of shutter and fixed with frame as in cabinet boxes with shelf and shutter full size fitted above the kitchen cooking platform and/or other platform including all necessary fittings and fixtures like nickle plated clip hinges, knobs, channels etc including dismantling boarding, any description, fixed in any position with nails complete all as specified and directed. Note : Items like cupboard knobs, stainless steel channel, CP plate clip hinges are included in the mentioned rates and as per manufacturesrs specification and drawing.The measured area shall be front elevation.

S&F in repair factory made PVC shutter of 18 mm thickness consisting of panel of 18 mm thick celluca ply of density 600 Kg.cbm density manufactured by an ISO 9000 certified company using for shutter celluca ply 18 mm thick cut in desired size of shutter and fixed with frame of kitchen accesory/cubboard at all four edges of shutter using 13/6 size self tapping steel screws. below cooking platform The thickness of the shutter is edfe painted by matching colour of PVC ink of plain colour of PVC sheet using complete all as specified and directed by Engineer-in-Charge and manufacturers specification. Note : Items like cupboard knobs, stainless steel channel, CP plate clip hinges are included in the mentioned rates and as per manufacturesrs specification and drawing.The measured area shall be front elevation.

M&L for repair to demaged RCC surfaces of chajjas, sofits of slabs, beams, columns, cantilever slabs, beams, columns, fins, stair, ralling, etc at any height and in any position including cutting / chipping the spalling concrete surfaces and providing welded steed wire fabric mesh 75x25mm of weight not less than 4.0 kg/sqm on prepared surface with suitable pins/clamps/ welding to the existing reinforcement and applying polymer modified cementous coating on concrete surface prepared for guniting and finished with 40mm thick (25 mm thick average) pressure Guniting in Cement morter 1:3, applied by pressure hoses finishing the plastered surface with two coats of cement base paint over a coat of primer complete all as specified and directed. [Note: Quoted rate is deemed to be inclusive for work at height and location including cost of scaffolding].

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors and similar works of Gde E-165(Fe 290) including welding etc. complete all as specified & as directed.

S&F Bands, straps, supports or stays for rainwater, ventilating, pipes, including bolts, if required: hooks (stays), heavy, for large gates, hooks and pintal hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle, cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way strapes, plate washers and similar small articles confirming to Fe 410 or Fe 310.

M/S JALANDRA CONSTRUCTIONS