REPAIR MAINT SERVICING OF HOIST CRANES EXHAUST BLOWER VENTILATION AIR COMPRESSOR CENTRIFUGAL FANS WITH MAINT OF STARTER CONTROL PANELS RELAYS CONTACTORS MCCBS AND VARIOUS MISC WORKS UNDER AGE EM II UNDER GE CENTRAL KHADKI

Amount

Taking down unserviceable old control panels at any location any height complete as directed.

Supply, install, testing and commissioning of CPRI approved factory make LT Panel board indoor type, pedestal mounted with suitable angle iron frame ,dust proof, weather proof, vermin proof front side single door hinge type with locking arrangement sheet steel cubical type made out of 2 mm thick CRCA sheet with powder coated finished suitable length and size. High conductivity 3 phase and neutral copper bus bar of 100 Amps capacity duly mounted on pre cast insulators including nuts and bolts and connecting electrically with suitable copper cable lug, cable glands etc complete all as specified and directed to accommodate the following items.

INCOMING : (a) MCCB 63 Amps 4 pole 36 KA - 01 Nos Make :- L&T or equivalent make given under list of makes (b) Advanced multi functional meter 4410 series LCD meter of L&T or equivalent make given under list of makes (c) LED type indication lamp for RYB OUTGOING : (a) MCCB 20 Amps 4 pole 36 KA - 04 Nos Make :- L&T or equivalent make given under list of makes (b) All the necessary required accessories for DOL starter for 5 HP motor - 04 Nos Make : L&T or equivalent make given under list of makes

Supply install testing and commissioning of CPRI approved factory make LT Panel board indoor type, pedestal mounted with suitable angle iron frame ,dust proof, weather proof, vermin proof front side single door hinge type with locking arrangement sheet steel cubical type made out of 2 mm thick CRCA sheet with powder coated finished suitable length and size. High conductivity 3 phase and neutral copper bus bar of 200 Amps capacity duly mounted on pre cast insulators including nuts and bolts and connecting electrically with suitable copper cable lug, cable glands etc complete all as specified and directed to accommodate the following items.

INCOMING : (a) MCCB 200 Amps 4 pole 36 KA - 01 Nos Make :- L&T or equivalent make given under list of makes (b) Advanced multi functional meter 4410 series LCD meter of L&T or equivalent make given under list of makes (c) LED type indication lamp for RYB OUTGOING : (a) MCCB 63 Amps 4 pole 16 KA - 02 Nos Make :- L&Tor equivalent make given under list of makes (b) MCCB 20 Amps 4 pole 16 KA - 04 Nos Make :- L&T or equivalent make given under list of makes (c) All accessories suitable for Star delta starter for 15 HP motor - 02 Nos Make : L&T or equivalent make given under list of makes (d) All necessary required accessories for DOL starter for 5 HP motor - 04 Nos Make : L&T or equivalent make given under list of makes

Supply, install, testing and commissioning of CPRI approved factory make LT Panel board indoor type, pedestal mounted with suitable angle iron frame ,dust proof, weather proof, vermin proof front side single door hinge type with locking arrangement sheet steel cubical type made out of 2 mm thick CRCA sheet with powder coated finished suitable length and size. High conductivity 3 phase and neutral copper bus bar of 100 Amps capacity duly mounted on pre cast insulators including nuts and bolts and connecting electrically with suitable copper cable lug, cable glands etc complete all as specified and directed to accommodate the following items.

INCOMING : (a) MCCB 63 Amps 4 pole 36 KA - 01 Nos Make :- L&T or equivalent make given under list of makes (b) Advanced multi functional meter 4410 series LCD meter of L&T or equivalent make given under list of makes (c) LED type indication lamp for RYB OUTGOING : (a)All necessary required accessories for Star delta starter for 20 HP motor - 01 Nos Make : L&T

Supply, install, testing and commissioning of CPRI approved factory make LT Panel board indoor type, pedestal mounted with suitable angle iron frame ,dust proof, weather proof, vermin proof front side single door hinge type with locking arrangement sheet steel cubical type made out of 2 mm thick CRCA sheet with powder coated finished suitable length and size. High conductivity 3 phase and neutral copper bus bar of 100 Amps capacity duly mounted on pre cast insulators including nuts and bolts and connecting electrically with suitable copper cable lug, cable glands etc complete all as specified and directed to accommodate the following items.

INCOMING : (a) MCCB 63 Amps 4 pole 36 KA - 01 Nos Make :- L&T or equivalent make given under list of makes (b) Advanced multi functional meter 4410 series LCD meter of L&T or equivalent make given under list of makes (c) LED type indication lamp for RYB OUTGOING : (a)All necessary required accessories for Star delta starter for 20 HP motor - 01 Nos Make : L&T or equivalent make given under list of makes

Supply install testing and commissioning of CPRI approved factory make LT Panel board indoor type, pedestal mounted with suitable angle iron frame ,dust proof, weather proof, vermin proof front side single door hinge type with locking arrangement sheet steel cubical type made out of 2 mm thick CRCA sheet with powder coated finished suitable length and size. High conductivity 3 phase and neutral copper bus bar of 100 Amps capacity duly mounted on pre cast insulators including nuts and bolts and connecting electrically with suitable copper cable lug, cable glands etc complete all as specified and directed to accommodate the following items.

INCOMING : (a) MCCB 100 Amps 4 pole 36 KA - 01 Nos Make :- L&T or equivalent make given under list of makes (b) Advanced multi functional meter 4410 series LCD meter of L&T or equivalent make given under list of makes (c) LED type indication lamp for RYB L&T OUTGOING : (a) MCCB 63 Amps 4 pole 36 KA - 01 Nos and MCCB 20 A 4 pole -01 No; Make :- L&T or equivalent make given under list of makes (b) All necessary required accessories for Star delta starter for 15 HP motor - 01 Nos Make : L&T or equivalent make given under list of makes (c) All necessary required accessories for DOL starter for 5 HP motor - 01 Nos Make : L&T or equivalent make given under list of makes

Supply, install, testing and commissioning of CPRI approved factory make LT Panel board indoor type, Wall mounted / pedestal mounted with suitable angle iron frame ,dust proof, weather proof, vermin proof front side single door hinge type with locking arrangement sheet steel cubical type made out of 2 mm thick CRCA sheet with powder coated finished suitable length and size. High conductivity 3 phase and neutral copper bus bar upto 100 Amps capacity duly mounted on pre cast insulators including nuts and bolts and connecting electrically with suitable copper cable lug, cable glands etc complete all as specified and directed to accommodate the following items.

INCOMING : (a) MCCB 32 Amps 4 pole 36 KA - 01 Nos Make :- L&T or equivalent make given under list of makes (b) Advanced multi functional meter 4410 series LCD meter of L&T or equivalent make given under list of makes (c) LED type indication lamp for RYB L&T OUTGOING : (a) All necessary required accessories for DOL starter for 5 to 10 HP motor - 01 Nos Make : L&T or equivalent make given under list of makes NOTE: i)Contractor shall visit the site before Quoiting the rates ii)The unit rate quoted shall deemed to include all the Addn/Altn required in the above work to be done by the contractor. iii)For the Pedestal mounted panels the required angle iron frame etc shall be deemed to be included under unit rate quoted.

Repair & Maint of Air compressor of model KES -75-10.5 of make Kirloskar of capacity 10.5kg/cum by dismantling top cover, fan with fan motor and cleaning the Air filter assy, Oil filter assy Greasing the motor and cleaning the total structure of compressor and control panel with air wash Changing the compressor oil complete and refixing the fan, frill & top cover testing commissioning complete all as directed by Engr-in-charge Note :- (i) The servicing is to be done by the Authorised Service provider of Kirloskar / manufacturer/OEM . (ii) The compressor oil and Spares to be changed shall be measured and paid separately under relevant item of this BOQ as Supply only.

Special hose assembly 2-1/2''x1200 L,90xST,Both side Flange, high temp.CP NO 270.00.577.50

Hose Assembly 1/4''x1000L ,CP NO 270.00.582.50

Special Union Assembly.1/4''x1/4'' BSP,CP NO 270.00.556.50

Intake valve Aseembly,CP NO 270.00.549.50

Supply Compressor oil suitable for air compressor of type KES - 75-10.5 (20 LTR Pack) CP No 270.02.478.50

Supply Dryer unit including compressor and connected valves etc suitable for compressor of type KES 75-10.5

Supply Controller unit including full assembly suitable for compressor of type KES 75-10.5

M&L for dismantling main/auxiliary Hook/hoist assy and taking down wire rope of EOT Crane of capacity of following capacities for carrying out repair / servicing work by dismantling the complete assy and cleaning the complete assy, replacement of unserviceable parts like bearing, locking plate, nuts & bolts, apply grease to bearings and all moving parts and painting the hook assembly with two coats of Red colour and assembling the same with existing/ new wire rope, testing for entire satisfaction of Engr-in-charge. Note :- (i) Necessary safety measures shall be taken by the contractor while dismantling and fixing the Crane hook/hoist. Contractor is responsible for any damage to the govt property during execution of job. (ii) The unit rate quoted shall deemed to include all necessary T&P, safety equipments for completion of the job. (iii) The unit rate quoted shall deemed to include all the Addn/Altn required in the above work to be done by the contractor. (iv) Wire rope if required measured and paid under relevant item as supply only.

EOT crane of capacity upto 5.0 ton

EOT crane of capacity 10 ton to 20 ton

EOT crane of capacity 50 ton

M&L for repair / replacement of EOT crane track, dismantling railing with help of welding, replacement of track railing as per existing size and specification, side supports at required distance, pressure plates with nut, bolts, washers, alignment of crane track complete including repair of track with necessary welding work for smooth functioning of EOT crane of following capacity all as specified and as directed. Note :- (i) Contractor shall visit site before quoting the rate. Necessary safety measures to be taken by the contractor while dismantling and fixing the Crane track as the work site is at the height of approx. 20 ft. (ii) Any damage to govt property while executing the work shall be make good by the contractor at no extra cost to deptt. (iii) Contractor shall provide skilled labour while executing the job. (iv) The cost of Scaffolding arrangement/Ladders/ safety belts/ Lifting Jacks and T & P used while working in the Crane shall be beared by the contractor. (v) Cost of track shall be measured & paid separately under relevant items as Supply only . (vi) New railing to be provided with the existing railing specification, size, materials and also with the proper fitment to the girder with the pressure plate, nut, bolts, washers etc (vii) After the work completion the testing to be done by the contactor in presence of JE /AGE for smooth functioning and entire satisfaction of Engr-in-Charge.

EOT crane of capacity upto 5.0 ton

EOT crane of capacity 10 ton to 20 ton

EOT crane of capacity 50 ton

M&L for dismantling & removing driving shaft of EOT Crane, coupling sets, clean shaft and coupling and repair/replacement of unserviceable coupling if required, bearing, nut & Bolts, removing bend of shaft, balancing the shaft with drive wheel and motor, greasing to the all moving parts complete for the EOT Crane of following capacity with the necessary works/alteration to make it functional all as specified and as directed by Engr-in-Charge at site Note: Coupling and bearing shall be paid separately under respective items of schedule if required as Supply only.

EOT crane of capacity upto 5.0 ton

EOT crane of capacity 10 ton to 20 ton

EOT crane of capacity 50 ton

Material and labour for repair /servicing of Crane Gear Box long travel/cross travel/aux hoist/main hoist of EOT crane of following capacity , at any height including draining gear oil, opening gear box, cleaning all parts, checking of gears, bearing, oil seal, replacement of oil, worn out gear with shaft, bearings, gasket, removal of leakage of oil, re-filling gear oil all as specified and as directed by Engr-in-Charge at site. Note:- (i) Crane gear Oil, gear with shaft, bearing etc shall be measured & paid separately under relevant items as Supply only, minor spares like, gasket, oil seal shall be deemed to be included under the unit rate quoted . (ii) Necessary safety measures shall be taken by the contractor while dismantling and fixing the various shafts, gears of gear box etc.

EOT crane of capacity upto 5.0 ton

EOT crane of capacity 10 ton to 20 ton

EOT crane of capacity 50 ton

Supply only following parts of Gear Box of EOT crane for replacement during servicing all as specified and as directed Note: Labour for fixing of spares shall be deemed to be included in the servicing item as above.

Gear oil for Crane Gear Box of long travel/cross travel/aux hoist/main hoist of EOT crane Make :- Servo /HP/ Castrol

Drive shaft with integral pinion and gear wheel assembly of gear box as per existing gears of crane upto 5 ton capacity

Drive shaft with integral pinion and gear wheel assembly of gear box as per existing gears of crane 10-20 ton capacity

Drive shaft with integral pinion and gear wheel assembly of gear box as per existing gears of crane 50 ton capacity

Output shaft with integral pinion and gear wheel assembly of gear box as per existing gears of crane upto 5 ton capacity

Output shaft with integral pinion and gear wheel assembly of gear box as per existing gears of crane 10-20 ton capacity

Output shaft with integral pinion and gear wheel assembly of gear box as per existing gears of crane 50 ton capacity

Breaing as per existing number ( 6008/6308/ 6212/22212/ 22216/ 2218 / 6210)

Crane coupling as per existing suitable for driving shaft of EOT Crane all as specified and as directed.

Material and labour for servicing of Crane drive wheel of long travel and cross travel with opening cover plate, bearing, shaft etc cleaning, checking and replacement of unserviceable parts, greasing all movable parts complete, crane of following capacity all as specified and as directed by Engr-in-Charge at site. Note :- (i) Necessary safety measures shall be taken by the contractor while dismantling and fixing the Crane wheel . Contractor is responsible for any damage to the govt property during execution of job. (ii) The unit rate quoted shall deemed to include all necessary T&P, safety equipment's for completion of the job. (iii) The unit rate quoted shall deemed to include all the Addn/Altn required in the above work to be done by the contractor. (iv) Contractor shall visit the site before quoting the rate

EOT crane of capacity upto 5.0 ton

EOT crane of capacity 10 ton to 20 ton

EOT crane of capacity 50 ton

Material and labour for servicing of Crane rope drum of crane of following capacity, taking down wire rope, cleaning rope drum, opening rope drum assembly, bearing block, bearing housing, coupling, cleaning of bearing and check for serviceability, greasing to bearing, replacement of worn out parts, oil seal etc, assembling rope on drum for smooth functioning of crane and testing of crane in presence of Engr-in-Charge. Note :- (i) Necessary safety measures to be taken by the contractor. Contractor is responsible for any damage to the govt property during execution of job. (ii) The unit rate quoted shall deemed to include all necessary T&P, safety equipment's for completion of the job. (iii) The unit rate quoted shall deemed to include all the Addn/Altn required in the above work to be done by the contractor. (iv) Contractor shall visit the site before quoting the rate

EOT crane of capacity upto 5.0 ton

EOT crane of capacity 10 ton to 20 ton

EOT crane of capacity 50 ton

M & L for cutting/fabricating, fixing & welding of MS angle iron/crane track railing/chequered plates of any size and shape as per site requirement for making platform of crane / making ladders/ repair of track / supports fixing brackets etc including bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint including removing old crane track /damaged supports/ ladders etc of any size all as directed at site by Engr-in-charge.

M&L for dismantling and removing of old unserviceable limit switch any type and S&F heavy duty two way lever type limit switches with 2 contacts and rated voltage upto 500V , 40 Amps with enclosure incl nut , bolts , mounting bracket etc and all electric connection done to existing cable complete all as directed by Engr-in - charge Make :- Top Enterprises/Speed control / BCH

All as per Item No 17.00 above but heavy duty one way gravity/Counter weight limit switches with 2 contacts and rated voltage upto 500V , 40 Amps Make :- Top Enterprises/BCH/Speed control

All as per Item No17.00 above but heavy duty Rotary geared type shunt limit switches with 2 contacts and rated voltage upto 500V , 40 Amps Make :- Top Enterprises/BCH/Speed control

Supply , Fixing and testing of Electro Hydraulic thruster of size / capacity 18 Kg all as existing type with first fill of hydraulic oil incl dismantling and removing old unsv thruster complete all as specified and directed by Engr-in-charge. Make :- Top Enterprises/ Speedocontrol

Supply , Fixing and testing of Electro Hydraulic thruster of size / capacity 34 Kg all as existing type with first fill of hydraulic oil incl dismantling and removing old unsv thruster complete all as specified and directed by Engr-in-charge. Make :- Top Enterprises/ Speed control

M&L for dismantling & removing old coupling sets, opening the motor for repair, taking out the burnt copper wire from motor, cleaning the stator thoroughly, rewinding the motor with super enamelled copper wire of same gauge complete with Varnish, heating the winding , reassembling, reconnecting and testing the motor of EOT Crane for smooth functioning of following capacity complete all as specified and as directed by the Engr-in-Charge. Note: (i) Contractor shall visit site before quoting the rate. (ii) Rates shall be deemed to be included for taking down motor from EOT crane, transporting to workshop and back to site.

upto 5 HP

M&L for dismantling and taking out old slip ring from the slip ring motor of following capacity and taking out carbon bushes from it. Cleaning the complete rotor assembly with CTC solvent and fixing new slip ring with new carbon brushes of existing type all as directed by Engr-in-Charge at site.

upto 5 HP

M & L for attending complaint of electrical and mechanical for Preventive maint/ normal repair/servicing of EOT Crane of capacity upto 50 Ton including replacement of unserviceable minor material like cotton waste, grease, lugs, thimble, wiring cable etc all as specified and as directed. Note :- i) Complaint will be notified to contractor on mobile phone at any time between 0800 hrs to 2200 hrs and will be rectified within 24 hours after notification, failing which Rs 500/- per day per complaint will be recovered ii) Contractor shall informed regarding major breakdown and the repair work shall be measured and paid respective items of this BOQ. (iii) Contractor shall visit site before quoting the rate. Necessary safety measures to be taken by the contractor while doing the job as the work site is at the height of approx. 20 ft. (iv) Any damage to govt property while executing the work is to be make good by the contractor at no extra cost to deptt. (v) Contractor should provide skilled labour while executing the job. (vi)i The cost of safety belts / Lifting Jacks and T & P used while working in the Crane shall be beared by the contractor. (vii) If during the complaint it is find out to be major problem, it shall be communicated to the concern JE and paid under relevant items

M&L for dismantling and removing of unserviceable driving /traveling for Long travel mild steel wheel including all accessories like Top plate, wheel shaft, bearing housing, bearings, driving axel, plumber block and wheel and connected accessories complete of EOT cranes of following capacity Cleaning all accessories to check the condition all as directed by Engr-in-Charge at site.

EOT Crane of capacity 0.5 ton to 5 ton.

EOT Crane of capacity 10 to 20 Ton

EOT Crane of capacity 50 Ton

M&L for assembling and testing driving /traveling for Long travel mild steel wheel including replacement of unserviceable spares and parts like wheel shaft, bearing housing, bearings, driving axel, plumber block, spacers/sims, nuts, bolts, washers and all packing materials, greasing the wheel and testing the crane of following capacity 0.5 ton to 5.0 ton for smooth functioning all as as specified and directed by Engineer-in-Charge at site.

EOT Crane capacity 0.5 ton to 5.0 ton

EOT Crane capacity 10 to 20 Ton

EOT Crane capacity 50 Ton cranes

Note for Item No 25.00 to 26. 00 :- (i) Contractor shall visit site before quoting. Necessary safety measures shall be taken by the contractor while dismantling and fixing the Crane Wheels as the work site is at the height of approx 20 ft. (ii) Any damage to govt property while executing the work is to be make good by the contractor at no extra cost. (iii) Contractor shall provide skilled labour while executing the job. (iv) All the Gears, bearings and shaft is to dismantled under hydraulic press or by the pullers only (v) The cost of Scaffolding arrangement/Ladders/ safety belts/ Lifting Jacks and T & P used while working in the Crane shall be beared by the contractor. (vi) Once intimated the contractor should complete the works within 3 working days, at the earliest otherwise a penalty of Rs 1000/- per day shall have to be paid by the contractor.

M/S. Niksun Electro-Infra Private Limited (BID ID -3257708)

PAMS ENTERPRISES (BID ID -3251766)

Bidder Name

PAMS ENTERPRISES

M/S. Niksun Electro-Infra Private Limited

Adinath Technical Services