Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹43.3 LAccepted-AOC NIVADA TIVAYA ROAD TIVYA MUST BUS STOP VILLAGE KHATAULI SAHARANPUR UP 247001 | SAHARANPUR | SAHARANPUR | UP | 247001 | L1 | Accepted-AOC Lowest and reasonable | |
| 2 | L2₹45.3 L+₹1.5 L (3.43%)Rejected-Finance | L2 | Rejected-Finance L2 | |
| 3 | L3₹47.2 L+₹3.4 L (7.66%)Rejected-Finance | L3 | Rejected-Finance L3 | |
| 4 | L4₹51.4 L+₹7.6 L (17.4%)Rejected-Finance H NO 209 D SHRI SHIVA NAGAR IV MANCHARA SIKAR ROAD JAIPUR | JAIPUR | JAIPUR | RAJASTHAN | 302013 | L4 | Rejected-Finance L4 | |
| 5 | Rejected-Technical | - | Rejected-Technical Not Approved |
Tender Value
₹60 L
EMD Value
₹1.1 L
Closing Date
12 Mar 2024, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
CWE JAIPUR
Military Engineer Services, HQ Commander Works Engineer, Kalyan Marg, Banipark, Jaipur-06
COMPREHENSIVE REPAIR INCLUDING PERIODICAL AND MAINT FOR JCO/OR MD ACCN IN UDHAM VIHAR ZONE III UNDER GE (S) JAIPUR
2024_MES_641317_1
CWE/JPR(S)/82302/E8
Open Tender
Civil Works
Item Rate
180 days
JAIPUR
As per NIT
8 documents required · 8 mandatory
₹1,000
GE SOUTH JAIPUR
₹1.1 L
Yes
5 Jun 2024
8 Feb 2024
14 Mar 2024
8 Feb 2024
12 Mar 2024
29 Feb 2024
8 Feb 2024 - 28 Feb 2024
Amount
M&L for preparation of old decorated surfacesby mechanical means of wall (plastered or unplastered) including cornices pillasters and other wall features by brooming down smoke, soot moulds and efflorescent salt and trading oil or greasy spots and applying one coat of white wash to obtain uniform surfaces including scafolding arrangement, trestles, ladders etc upto four storey all as specified and directed.
All as per Srl No. 1 above but two coat of white was on wall.
All as per Srl No. 1 above but one coat of white wash on ceiling.
All as per Srl No. 1 above but two coat of white was on ceiling.
All as per Srl No. 1 above but one coat of distemper oil emulsion on wall.
M&L for preparation of newly plastered surfaces and applying three coats of white wash on walls complete all as specified and direcrted.
M&L for preparation of newly plastered surfaces and applying two coats of oil bound distemper on walls including one coat of alkali resistant wall primer complete all as specified and direcrted.
M&L for preparation of newly plastered surfaces and applying two coat of white was on ceiling complete all as specified and direcrted.
M&L for preparation of newly plastered surfaces and and applying two coat of cement base paint complete all as specified and direcrted.
M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coats of oil bound distemper of approved tint over one coat alkali resistant wall primer complete all as specified and direcrted.
M&L for preparing of old paianted surfaces of wood or wood based materials of any description over 10 cm width or girth and applying on coat of synethic enamel paint on wooden surfaces all as specified and directd by Engineer-in-Charge
AII as per Sr Item No 11 above but one coat of paint on steel surface
Taking down chowkat or frames with shutters (with out taking off shutters from the frame) n. exe 1.50 SQM each as directed.
All as per item No 13 above but exe 1.50 SQM but n .exe 4.00 SQM each.
Taking down shutters of any description exe 1.00 SQM but n.exc 2.00 Sqm each complete all as specified and direcrted.
All as per item No 15 above but exe 2.0 SQM each.
M&L for pressed steel frames for door with one Or more rebated including necessary fixing lugs hinges locks strike plates etc complete all as specified and fixed of size 125x 60mm complete all as specified and direcrted.
M&L for pressed steel frames for door with one Or more rebated including necessary fixing lugs hinges locks strike plates etc complete all as specified and fixed of size 105x 60mm complete all as specified and direcrted.
M& L for PCC 1:3:6 type C1 as in filling of steel chowkhats complete all as specified .
S&F IInd class Hard Wood (Sal/hollock) factory made plain framed panelled shutters 35 mm thick (any number of pannel) with panels of timber flats on both sides (feather edged) or of veneered particle board medium density , wood particle board with commercial face veneers complete all as specified and directed.
S&F 2nd class hard wood (sal/hollock) 35 MM thick glazed and skeleton shutters open rebated and prepared to revive glass ,gauze etc (with out sash bars) edges for framing plain chanferred or rounded fitted with cut and mitred beads for securing glass etc, size Pt-I clause 8.20 (a) for doors completed as specified and directed.
S&F factory made solid PVC door frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube and edges will be painted to match with painted sheet complete all as specified and directed.
S&F factory made solid pannel PVC door shutters 30 mm thick consisting of frame made out of MS tube for styles, top and bottom rails , mild stell frame shall be covered with heat moulded plaing colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail , paneeling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed togther with solvent cement , complete all as specified and directed
S&F powder coated aluminimum anodised frame fixed type with aluminum section weighing 0.55 kg/mtr incl necessay joining , cleats, glazing clips , rubber packing anodised aluminimum snap beading , screws etc complete all as specified and directed.
S&F powder coated aluminimum anodised door/window shutter openale / sliding type with aluminimum section weighing 0.55 kg/mtr incl necessay joining , cleats, glazing clips , rubber packing anodised aluminimum snap beading , screws handle tower bolt etc complete all as specified and directed.
S&F factory made Mild Steel windows with side hung shelters incl projecting type hinge with steel handle and steel peg stay complete with glazing bars dovetailed or welded including taking down of existing steel windows complete all as specified and direcrted.
S&F factory made Mild Steel ventilators with top hung shelters incl hinge with steel handle and steel peg stay complete all as specified. Including taking down existing steel ventilators complete all as specified and direcrted.
S&F MS framed work such as grills , gratings guard bars etc with ends of bars shouldred or rivetted or forged into spikes conforming to Fe-310-0 or Fe-410-0 complete all as specified and directe
S&F 100 mm size MS butt hinges, medium weihgt complete all as specified and direcrted.
S&F 300 mm long MS sliding door bolt of stove enameled black (clip type)with bright bolt not less than 12 mm dia with and including a iminimum of 6 bolts and nuts complete fitted all as specified and directed .
S&F mild steel barrel tower bolt stove enamelled black with bright bolt 150 mm long complete all as specified and direcrted.
S&F mild steel pressed handle ovel type stove enamelled black with bright bolt 125 mm long complete all as specified and direcrted.
S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire with average width of aperture 1.18 mm fixed with tinned tacks or galvanised wire stapels fixed etc complete all as specified and directed.
M&L for preparation of new wooden surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.
M&L for preparation of new steel surfaces of any description over 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and direcrted.
S&F mild steel spring 300 mm long , ordinary rat tail rod pattern including roller and roller plate complete fixed to wooden /angle iron chowkat complete all as specified and direcrted.
S&F aluminimum, anodised, barrel tower bolt 150 mm long complete all as specified and direcrted.
S&F 300 mm long aluminimumu, anodised sliding door bolt with hasp, and staple bolt type and fixing a clamps of sheet , cast or extruded sections complete fitted all as specified and directed .
S&F aluminimum , anodised bow handle 125 mm long complete all as specified and direcrted.
S&F 4.00 mm thick sheet glass of ordinary quality and glazing with oil putty in square or fixed with beads in squares nexe 0.50 SQM in each pane complete all as specified and directed.
Demolition of brick work built in cement mortar including all quoins arches , pillers etc all as specified and directed
M&L for brick work with dub class ' B ' bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.
Taking down plastering cement lime or cement plaster on brick or stone walls including raking out joints hacking for key, scrubbing down with water any description all as specified and directed any of description of wall all as specified.
M&L for rendering 15 mm th in cement mortar 1:6 on wall of brick work or concrete surfaces finished fair and even complete all as specified and directed.
M&L for rendering 15 mm th in cement mortar 1:4 on wall of brick work or concrete surfaces finished fair and even complete all as specified and directed.
M&L rendering 5 mm thick in cm 1:3 ceiling of concrete/brick surfaces even and smooth w/o using extra cement complete all as specified and directed.
Taking down old and S&F pressed steel cup board shutters with frame , the frame shall be made of 1.25 mmthick and shutter made of 1.00 mm thick PBI sheet with 6 Nos 100 mm long steel hinges , Godrej pattern locking arrangement including 12mm dia vertical rod all as per TD drg No CEJZ /TD 2004/29 . The surfaces shall be spary painted with two coat of synthetic enamel paint over a coat of zinc chromate primer over cleared surface complete all as specified and directed and shown on drg (Total width including frame shall be measured flat and paid.
Dismentling , floor hearth or wall tiling including CM (but not backing ) removing seviceable tiles to store & rubbish off the premises complete all as sepecified.
M&L for coloured ceramic tile (1st quality) of size 350mm x 450mm x 6 to 7 mm thick as on vertical surface set & jointed in neat cement slurry and pointed in white /coloured cement to match the tiles over & including 10 mm thick plaster in CM (1:6) all as specified and directed.
M&L for coloured Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of Each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm , in floors etc set jointed in neat cement slurry and pointed in white or coloured cement match over & including 15 mm thick screed bed in CM(1:4) completed all as specified
M&L for coloured Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of Each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm , in floors etc set jointed in neat cement slurry and pointed in white or coloured cement match over & including 15 mm thick screed bed in CM(1:4) completed all as specified
M&L for machine cut Kota stone slab flooring 20-25 mm thick over cement screed bed 15 mm thick in CM (1:4) laid & jointed with grey cement slurry mixed with pigment to match the shade of flooring including rubbing and mirror polishing complete all as specified
S&F 4.00 mm thick frosted glass of ordinary quality and glazing in square n. Exc 0.5 sqm in each pane as required as directed by Engr -in-Charge.
Hacking out old broken glass pane (any thickness, size, quality , dexcription) from metal /wood frame including punching or drilling out old glass panes, pins, springs clips & fixing 3.00 mm thick sheet glass / frosted glass of ordinary quality and glazing in square as required as directed by Engr -in-Charge.
Demolition of cement Concrete of floor n. exc 15 CM below or above the GL etc, complete all as specified and directed.
M&L for brick work with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 etc, complete all as specified and directed.
S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I , 500 Ltrs Capacity including Dismantling of old water tanks etc, complete all as specified and directed.
S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 1000 Ltrs Capacity including Dismantling water tanks etc, complete all as specified and directed.
S&F in repair Ball brass valves 20mm bore, high pressure, with polythene float & flynut complete, screwed for iron pipe or brass ferrule etc, complete all as specified and directed.
S&F in repair Ball brass valves 25mm bore, high pressure, with polythene float & flynut complete, screwed for iron pipe or brass ferrule etc, complete all as specified and directed.
S&F in repairs Bib taps 15 mm bore, cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule of fancy type etc, complete all as specified and directed.
S&F in repairs Stop valves 15 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions etc, complete all as specified and directed.
S&F GI Tubes, `medium grade' with all fitting & fixed complete to walls & ceilings or laid in floors of 15mm bore including taking up or down steel tubing & connections etc, complete all as specified and directed.
S&F GI Tubes, `medium grade' with all fitting & fixed complete to walls & ceilings or laid in floors of 20mm bore including taking up or down steel tubing & connections etc, complete all as specified and directed.
S&F GI Tubes, `medium grade' with all fitting & fixed complete to walls & ceilings or laid in floors of 25mm bore including taking up or down steel tubing & connections etc, complete all as specified and directed.
S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm etc, complete all as specified and directed.
S&F in repairs Vitreous China squatting pan 'orissa ' pattern `, size 580mmX 440 mm white ,with integral foot rests,(exclusing flushing cistern & flush pipe) including connection to trap and to flush pipe etc including set in and including concrete etc, complete all as specified and directed.
S&F in repairs Vitreous China wash basin, white, flat back, size 630x450mm excluding taps, waste chain & plug & porcelain stopper but including brackets etc, complete all as specified and directed.
S&F in repair CP Pillar taps 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe etc, complete all as specified and directed.
S&F in repair Stop valves 15 mm bore fancy type, CP with long shank & cup (conncelaed type), cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions etc, complete all as specified and directed.
S&F in repair Swivel shower of PTMT any colour for fixing with 15mm pipe (min. weight 40gms) etc, complete all as specified and directed.
S & F in repair Grating doom 125 mm dia of with waste hole of PTMT etc, complete all as specified and directed.
S&F in repair mild steel spring hinges 300 mm long , ordinary rat tail rod pattern including roller and roller plate complete fixed to wooden /angle iron chowkat etc, complete all as specified and directed.
S&F in repair 100 mm size MS butt hinges, medium weihgt etc, complete all as specified and directed.
S&F in repair 300 mm long MS sliding door bolt of stove enameled black (clip type)with bright bolt not less than 12 mm dia with and including a iminimum of 6 bolts and nuts complete fitted etc, complete all as specified and directed.
S&F in repair mild steel barrel tower bolt stove enamelled black with bright bolt 150 mm long etc, complete all as specified and directed.
S&F in repair mild steel pressed handle ovel type stove enamelled black with bright bolt 125 mm long etc, complete all as specified and directed.
S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire with average width of aperture 1.18 mm fixed with tinned tacks or galvanised wire stapels fixed etc complete all as specified and directed.
S&F in repair PVC valve less syphonic action type low level flushing cistern coloured with inlet ball valve float and handle incl bracket 10 Lit capacity etc, complete all as specified and directed. Make:- slimline / Paryware or equivalent as approved by GE
S&F in repair Flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern etc, complete all as specified and directed.
S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm etc, complete all as specified and directed.
S&F in repair PVC Waste Pipe 32 mm bore for WHB etc, complete all as specified and directed.
S&F in repairs angle stop cock 15 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions fancy type chromium plated etc, complete all as specified and directed.
M&L for welding in repairs. Exc 2.5cm but n.exc 5 cm in length and exc 6 mm but n.exc 9 mm thickness of metal etc, complete all as specified and directed.
M&L for Running welding in repairs n.exc 6 mm thick etc, complete all as specified and directed.
Demolition of PCC in roof covering, kerbs, roof kerbs, benching, coved fillets etc including old decayed water proofing treatment of any type all as directed by Engineer-in-charge.
M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 25 mm thick PCC type B-0, (1:2:4) using 12.5mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop with WPC @ 3% weight of cementetc, complete all as specified and directed.
The surface shall be painted with one coat of polymeric primer @ 0.30 Kg per sqm, conforming to IS : 3384. A layer of APP based polymeric membrane, 3 mm thick (min), weighing not less than 3.5 Kg/m2 reinforced with polyster non woven fabric ( weighing not less than 150 gms/ Sqm). Application of polymeric membrane shall be by torch application all as per manufacturer instructions etc, complete all as specified and directed.
M&L applying one coat of alluminium paint on surface of any description wood,steel,iron, concrete,brick , stone etc exc 10 cm in width or girth, application of paint shall be as per manufacturers instructions etc, complete all as specified and directed.
Roof Treatment:- 1. Complete removal of the existing roof treatment and disposed of the rubbish outside MOD land. 2. All visible cracks to be opened up in V shape and remove all loose particles, cleaned properly with wire brushes and cracks are to be filled with crack filling compound for cracks upto 15 mm width/depth of cracks. 3.Applying high build elastomeric water prrofing coating based on alphabetic polyeurethane,cold applied of spray/brush applied ,membrane with an elongation of 350%and crack bridging ability of 2mm as per ASTM D 412.The system including final base preparation ,single coat of single component PU based primer and applying Berger HS Elastomer or equivalent brand of other manufacturein two coats to achievea min thickness 1.2mm ,complete as per manufacture specification. 5. Necessary guarantee of 10 years shall be submitted by the contractor.
Supplying only Integral waterproofing compound
PCC 1:2:4 mix type B-0 (using 12.5 mm graded aggregate ) as in roof kerbs rounded or chamfered on edges etc, complete all as specified and directed.
Chipping the RCC surface and cleaning the rusted reinforcement and exposed surface by wire brush, mechanical device or any other established method and applying the rust removing solution of approved make and quality with cotton swab to reinforcement and allowing to dry the same for 24 hrs ,brushing of loose particles and applying 1st coat of rust preventive coating of polymer and cement slurry in 1:1.5 proportion with soft brush without adding water including applying another coat of rust preventing after 4 hrs allowing air curing for 48 hrs etc, complete all as specified and directed. (Note: Rate for formwork inclusive )
S& F hard drawn steel wire fabric n exc. 4 kg/Sqm weight cut to length bent to shape required and tying with & incl mild steel wire (annealed) not less than 0.9 mm dia as in reinforcement etc, complete all as specified and directed.
M & L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work n exc 20cm wide with rough finished surfaces etc, complete all as specified and directed.
M & L for 15mm thick polymer mortar to load carrying RCC members in two layers in proportion of 1:5:15 by weight of polymer of approved make and quality, cement and quartz sand with required WC ratio for desired consistency and applying and finishing by floating, curing after initial setting time etc. as per manufacturer specification etc. complete all as directed and specified.
M & L for applying SBR bond chemical of approved make before applying polymer plaster/ concrete to have the perfect bond between old concrete and new concrete/ polymer plaster surface using nylon bruses scaffolding labour etc. complete all as directed
Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, chajjas, fascias, fins and similar works etc, complete all as specified and directed.
S and F Mild steel TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips etc, complete all as specified and directed.
S and F Mild steel TMT bars 6 to 8mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips etc, complete all as specified and directed.
Formwork to chullah hoods, chajjas, troughs and similar items including edges etc, complete all as specified and directed. Note : Including Chajja upto 2nd floor
Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc, complete all as specified and directed.
Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc, complete all as specified and directed.
M & L Nominal mix cement concrete 1:11/2:3 as in chajjas etc, complete all as specified and directed. Note : Including Chajja upto 2nd floor
M & L for drilling and fixing holes in RCC members including drilling 14mm dia 50 to 100 mm deep holes in structural members at the intervals of 150 mm in staggered manner all as directed including cleaning the holes by air blowers prior to fixing TMT bar 10 mm dia in cleaned holes . TMT barsto be fixed by mean of epoxy to ensure complete sealing and cure the system for min 12 hrs under supervision of qualified supervisor all as specified and directed.
Demolition and cleaning of sunken portion including M & L for WPT in sunken floors as described here under:- Sunken floor and sides up to finished floor level shall be plastered with 15 mm thick cement laster in CM 1:4 mixedd with water proofing liquid @ 150ml per bag of cement. (ii) Preparing plastered surfaces and provinding APPpolymetric water proofing membrane, minimum 3 mm thick and weighing not less than 3.0 kg/sqm of make super thermolay manufactured by STP ltd or hyper plas (Polyster) manufactured by M/S IWL Ltd or 'Shatiplus' (Polyster) manufactued by M/S Capital Steels and chemicals Pvt Ltd as approved by GE, black finish reinforced with non-woven polyster matt, woth a thermo fusble finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or EMW Flate of M/S Texas India Ltd) at the rate of 0.40 Ltr/Sqm torching overlaps with a propane or a butane gas torch with a Over lap of 75 mm at the sides and 100mm at the ends sealing including applying a coat of cold emulsin bitumiouns primer all as per manufacture instrctions including prepartion of surface and filling lime concrete 1:5:10 type E2 with brick bats complete all as specified an as directed Note:- (i) Polymeric membrane shall be laid in sunken floor and on sides up to finished floor level. (ii) The Waterproofing treatment shall be got crried out by the manufacture or their authorised applicatiors (iii) Above aspects are deemed to be included in quoted rate (iv) Supply only water proofing liquid shall be measured and paid seperaterly (v) Slab area only will be measured for payment purpose.
M&L for preparation of old decorated surfacesby mechanical means of wall (plastered or unplastered) including cornices pillasters and other wall features by brooming down smoke, soot moulds and efflorescent salt and trading oil or greasy spots and applying one coat of cement base pain to obtain uniform surfaces including scafolding arrangement, trestles, ladders etc upto four storey all as specified and directed.(All colour shall be factory made and no pigment to be used to make the desired shade at site )
M& L for preparation of old/new surfaces of wall and applying one coats of weather proof paint (exterior acrylic emulsion Paint )using hand roller over one coat of water based white pigment alkali resistant priming paint on facia, cornices, chajjas and balcony s etc includding all necessary arrangement such as scaffolding /working platform for exxecution of work upto four storey building etc by skilled labour complete all as specified and directed by Engr in Charge . Note: Make should be Apex shine of Asian Paint or anti dust of Berger or mica marble of nerolac (All colour shall be factory made and no pigment to be used to make the desired shade at site )
M&L for Writing letters or figures (Block.Roman, Italic or Indian) n exc. 30 cm high by using of synthetic enamel paint including white enamal paint on base etc
Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc
M&L for point wiring with 1.5 Sq mm single core, multi-stranded copper conductor cable FRLS PV insulated unsheathed cable 1100 volt grade drawn through and including PVC casing capping and all fittings/accessories fixed to walls/ceilings all as per IS including hard wood board and 3 mm thick laminated sheet top covers including 1.5 Sq mm copper PVC insulated unsheathed continuous earth wire and connected to common earth dolly complete for the following:- (Note: Cost of hole cutting in wall for bell point, bulk head, building security light and any other site requirement during work execution shall be inclusive in above quoted price. Wiring on stone wall is included in above quoted price.)
(a) One light / fan / bell controlled by one, one way switch.
(b) One 3 pin 5 Amp socket out let on the same board with other switches
(c) One 5 Amp socket independent controlled by one, one way switch.
(d) One light point controlled by two, two way switches.
Description all as per item No 116 here in befor but with 1100 volts grade copper standard conductor cable of size 2.5Sqmm for 3 pin switch socket outlet 15Amp independent board complete all as specified and directed by Engineer in charge .
All as per Item No 116 above but with 4 Sqmm copper cable for 3 pin 15 Amps socket outlet on independent board, including 4.0 Sqmm copper cable continuous earth wire and connecting to common earth dolly.
M&L for point wiring using approved colour coding as per IS, with stranded copper conductor 1.5 Sq mm (nominal area), single core, FRLS PVC insulated and unsheathed cable 1100 volts grade, confirming to IS-694/ISI marked, drawn in and including rigid PVC casing caping, medium grade, ISI marked, with mild steel sunken boxes recessed in earth dolly and including mounting frame over cover plate, covered metal sheet, including PVC insulated stranded copper conductor 1.5 Sq mm (nominal area) FRLS single core cable as earth continuity conductor to common earth and connecting to earth dolly including, making opening for conduit/ sunken boxes on existing stone masonry and making good as per existing complete for the following :-
(a) One light / fan / bell controlled by one, one way switch.
(b) One 3 pin 5 Amp socket out let on the same board with other switches
(c) One 5 Amp socket independent controlled by one, one way switch.
All as per Item No 119 above but with 4 Sqmm copper cable for 3 pin 15 Amps socket outlet on independent board, including 4.0 Sqmm copper cable continuous earth wire and connecting to common earth dolly.
S&F switch piano type single pole one way 06 Amp 230 volts etc. complete all as specified and directed.
S&F switch piano type single pole one way 15/16 Amp 230 volts etc. complete all as specified and directed.
S&F switch piano type single Pole, two ways 6 amp rating 230 volts etc. complete all as specified and directed.
S&F bell push plush type, 6 amp rating 230 volts etc. complete all as specified and directed.
S & F Socket outlet multipurpose type 230/250 Volts 2 in 1, 3 pin 5/6 Amp ratings etc. complete all as specified and directed.
S & F Socket Piano type 230/250 Volts 2 in 1, 3 pin 15/16 Amp etc. complete all as specified and directed.
S&F S&F Electric multi music type AC 230 volts single pole etc. complete all as specified and directed.
S & F modular type electronics fan regulator flush type AC 230 volts single pole (ISI marked) for AC 230V, 50 Hz on laminated sheet etc. complete all as specified and directed. Make : Achor Cat Part No. 22546 or equivalent as approved by GE
S&F Ceiling rose surface bakelite 65x50mm, 3 Phase/ PVC/ Polycarbonate isolated body (ISI marked) etc. complete all as specified and directed.
S&F lamp holder, angle type, polycarbonate type with back plate suitable for batten fittings etc complete all as specified & directed.
Supply and fix Batten LED light fittings 20/22 Watt, 240 Volt 4 feet size long life surface/wall mounting IP 20 Luminaire per watt maximum extruded aluminium housing with frosted PMMA diffuser with high brightness LEDs complete with all accessories pre wired twin core twisted flexible copper conductor cable with suitable size. Make: LUMILINMILINEPLUSBS20WLED865SPCSS or equivelent model in Bajaj/Crompton/ Philips as approved by GE
All as per item No 132 here in before, but LED light fitting 1 x 8/10 W ,240 volt( size-2 feet) Make - Siska CAT part No SSK-RA-0801-N or equivelent model in Bajaj/Wipro/ Philips /CG /Surya roshni
Supply & fixing 10 W LED IP -65 Bulkhead environmental friendly, ultra modern, energy saving, surface mounted decorative Hexagon bulk head back lit LED luminaire comprising of high brightness LEDs wall mounted complete with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size etc complete all as specified and directed. Make - Havells cat No HEXAFT10WLED857SSYMBOPC or equivelent model in Wipro/ Philips/C G
M&L for Sub main wiring with two runs of 6 Sqmm single core FRLS PVC insulated but in unsheathed multi stranded copper conductor cable 1100 volts grade drawn through and including of 25mm dia PVC rigid conduit medium with conduit accessories and fixed to the surface of wall/ceiling as per ISI including 6.0 Sqmm PVC insulated copper conductor earth continuity wire including taking down old of any description etc complete all as specified and directed.
S&F Factory made, sheet distribution boards, double door protection class IP-42 suitable for mounting MCB/ MCCB, confirming to IS-13032, IS-8623, BS-5484 r of the under mention rating including taking down old etc complete all as specified and directed. :
TP&N 4 Way
SP&N 12 ways
SP&N 8 ways
SP&N 4 ways
S&F in repair MCB 10 KA confirming to IS-8828 : 1996, IEC-898 : 1995 rupturing capacity of the under mentioned type and rating :-
(a) SP 5 to 32 amps
(b) TPN 63 Amp
(c) SPN 32 to 63 amps.
Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.3 mm burried directly in ground (earth pit not less than 2.25 meters deep below normal ground level ), with top edge of the plate not less than 1.5 mtrs below normal ground level , connected to and including galvanised earth strip 25X 4 mm by means of galvanised iron bolts , nut and washers and connected to other end to main panel board duly protected by galvanised iron pipe 25 mm dia " light grage " earth plate surrounded by packed layer of coat dust and common salt 15 cm thick all around bottom and top watering pipe 20 mm bore of galvanised iron " medium grade " with funnel all as shown on electrical plate No 5 of SSR part -I and connecting to earthing testing on completion including cast iron cover frane and PCC 1:3:6 type C-2 using 20 mm grade stone aggregate as in earthing pit with cast iron cover and frame including necessary earth work etc complete all as per specified and directed by Engr-in-Charge . ( Note : PCC Chammer shall be constructed atleast 1.5 mtrs away form the earth electrode of the earth pit and pipe for watering shall be provided in slanting manner).
Supply and fix in repair sheet metal enclosure complete with metallic plug and socket heavy duty moduler type 3 pin (2P + Earth), 32 amp rating single phase 240 volts complete with MCB SP 32 amp “C” series etc complete all as per specified and directed
S&F in repair switch piano type single pole one way 06 Amp 230 volts etc. complete all as specified and directed.
S&F in repair switch piano type single pole one way 15/16 Amp 230 volts etc. complete all as specified and directed.
S & F in repair piano type electronics fan regulator flush type AC 230 volts single pole (ISI marked) for AC 230V, 50 Hz on laminated sheet etc. complete all as specified and directed. Make : Achor Cat Part No. 14503 or equivalent as approved by GE
S & F in repair Socket outlet multipurpose type 230/250 Volts 2 in 1, 3 pin 5/6 Amp ratings etc. complete all as specified and directed.
S & F in repair Socket Piano type 230/250 Volts 2 in 1, 3 pin 15/16 Amp etc. complete all as specified and directed.
S&F PVC rectangular block for mounting, switches, sockets, fan regulator etc. with 3 mm thick plastic laminated sheet cover of size 100 mm x 100 mm and 50 mm deep etc, complete all as specified and directed
S&F PVC rectangular block for mounting, switches, sockets, fan regulator etc. with 3 mm thick plastic laminated sheet cover of size 175 mm x 100 mm and 50 mm deep etc, complete all as specified and directed
S&F PVC rectangular block for mounting, switches, sockets, fan regulator etc. with 3 mm thick plastic laminated sheet cover of size 200 mm x 150 mm and 50 mm deep etc, complete all as specified and directed
S&F PVC rectangular block for mounting, switches, sockets, fan regulator etc. with 3 mm thick plastic laminated sheet cover of size 200 mm x 250 mm and 50 mm deep etc, complete all as specified and directed
S&F PVC rectangular block for mounting, switches, sockets, fan regulator etc. with 3 mm thick plastic laminated sheet cover of size 350 mm x 300 mm and 50 mm deep etc, complete all as specified and directed
Schedule of Credit
J.J.ENGINEERING
MSR INFRATECH
Satish kumar and company
stage.html
html • 0.05 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .