ADDN/ALTN TO GALVALUME SHEET ROOFING, RCC WATER TANK IN BLDG NO P-227/7 AT AJAY BAUGH AND SPL REPAIR FOR REPLACEMENT OF AC AND WATER COOLERS OF INS UTKROSH AND MINNIEAY AREA AGAINST BER UNDER GE MINNIEBAY, PORT BLAIR

Amount

Demoliton of cement concrete including tiles and mortar of any description and in any position not otherwise specifically provided for complete all as specified and as directed

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed

M & L for 15 mm thick cement plaster in CM 1:3 on concrete surfaces mixed with water proofing compound as per manufactures instruction,finished even and smooth and after ponding test surface shall be dried and bottom and sides of the sunken slab shall be treated with two coats of surface application using approved water proofing compound as per manufactures instructions all as specified and as directed. Note : WPC will be measured and paid seperately

M & L for applying a coat of hot blown bitumen 85/25 @ 1.2 Kg/Sqm over a coat of bituminous primer @ 0.3 Kg/Sqm complete all as specified and as directed.

M & L for 40 mm thick PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in sub base for flooring/levelling coarse etc complete all as specified and as directed.

M&L for coloured non-skid Ceramic tiles edge to edge joint 7 to 8 mm thick area of each tiles exc 0.18 Sqm but n.exc 0.38 sqm in floors etc colour as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM (1:4) all as specified.

M&L for ceramic tiles edge to edge joint 7 to 8 mm thick area of each tiles exc 0.18 Sqm but n.exc 0.38 sqm on vertical surfaces as skirting set and jointed in neat cement slurry and pointed in coloured cement to match with floor tiles including 10 mm thick backing coat in CM (1:4) as specified and direceted.

M&L for Coloured Non-skid/matt finish Ceramic tiles 7 to 8 mm thick exc. 0.06 sqm but n.exc 0.11sqm area of each tiles in floor/ steps etc set and jointed in neat cement slurry and pointed in coloured cement to match as in floor over and including 15mm thick screed bed in CM (1:4) complete all as specified and as directed

M&L for Glazed Ceramic tiles 450x300x 8-10 mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick backing in cement mortar (1:3) all as specified and directed

M&L for granite (of any type) 16 to 20mm thick machine cut fixed on slab,window cill etc , bedded & jointed with grey cement slurry & pointed with white cement with admixure of pigment to match the shade of granite stone including cutting, moulding & polishing over and including 20mm thick screed in CM (1:4) complete all as specified and as directed

M & L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed

M & L for vitrified chequered tiles 30cm x 30cm x 10 mm thick, set, jointed and pointed in near cement slurry in floors/skirtings with grey cement and pigments and including screed bed 15mm thick in CM 1:4 complete all as specified and as directed

Demolition of precast concrete block walling built in Cement Mortar including all quoins arches pillars etc complete all as specified and as directed.

M&L for PCC block masonry with solid block, exc 10cm in width in PCC type C-1, 1:3:6 using 20mm graded stone aggregate set in CM (1:6) complete all as specified and as directed

Taking down cement plaster of any description on brick or stone walls or concrete surfaces, ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed..

M & L for rendering to concrete or block masonry surfaces or surfaces other than fair faces of brick surfaces, 10mm thick in CM 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering 5mm thick in CM (1:3) on ceiling surfaces finished even & smooth without using extra cement complete all as specified and as directed.

M & L for rendering 5 mm thick in cement mortar 1:4 over a backing coat of 10mm thick in CM 1:6 (Total 15 mm thick) on concrete or brick masonry surfaces including mixing water proofing compound as per manufacurers instructions and finishing the top surface even and fair complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for rendering 5mm thick in CM (1:3) on ceiling (external) surfaces finished even & smooth without using extra cement including mixing water proofing compound as per manufacurers instructions and finishing the top surface even and fair complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

Supply only Integral water proofing compound ISI marked complete all as specified and as directed.

M & L for applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil emulsion distemper over a coat of primer complete all as specified and as directed

M&L for preparation of newly plastered surfaces of ceiling and applying two coats of oil emulsion distemper over a coat of primer complete all as specified and as directed

M & L for complete removel of existing treatment on wall, finishing the surface and appliying two coat of oil bound distemper over a coat of primer complete all as specified and as directed

M & L for complete removel of existing treatment on ceiling and applying two coats of oil emulsion distemper over a coat of primer complete all as specified and as directed

M & L for complete removal of existing treatment, preparation of plastered wall surfaces and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm complete all as specified and as directed

M & L for applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed

Supply and laying in replacement of of CPVC pipes 20 mm dia outer bore SDR 11 & plain CPVC SDR 11with all special fittings on walls /ceilings or laying in floors complete all as specified.

Supply and laying in replacement of CPVC pipes 25mm dia outer bore SDR 11 &plain CPVC SDR 11 with all special fittings on walls /ceilings or laying in floors complete all as specified.

S&F 20 mm outer dia CPVC Male Brass Threaded Adaptor (MTA/MBTA) complete all as specified and as directed

S&F 25 mm outer dia CPVC Male Brass Threaded Adaptor (MTA/MBTA) complete all as specified and as directed.

S&F 20mm outer dia CPVC pipes brass Elbow (3/4 X1/2) complete all as specified and as directed

S&F 20mm outer dia CPVC female brass adaptor (FTA/FBTA) complete all as specified and as directed

S&F 25 mm outer dia CPVC female brass adaptor (FTA/FBTA) complete all as specified and as directed

S&F 20 mm outer dia CPVC Brass Tee complete all as specified and as directed

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M & L for RCC 1:2:4 type B1 using 20 mm graded stone aggregate as in slab supported on walls, beams and columns in floors, roofs, landings, deck slab, shelves and like complete all as directed.

M & L for Use and waste of formwork with fair finished surface to soffits of suspended slabs such as roof slabs, floor slabs, landings and simillar work horizontal or sloping etc complete.

M&L for TMT bars 10mm dia and over cut to length, bent to shape required incl cranking and hooking ends and binding with MS wire (annealed) of dia not less than 0.90mm all as specified and directed.

S&F 25mm Ball brass valve high pressure of polyethylene float and fly nut complete screwed for iron pipe and fixed, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule etc and fixed complete all as specified and as directed

Dismantling of plain or corrugated steel sheeting any guage thickness or similar pattern roof coverings complete all as specified

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as manufacturers instruction complete all as specified and as directed

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley gutter, drip, and straight flashing complete all as specified and as directed

M&L for roof trusses (framed), trusssed, purlings, crane gantries, rails and fasternings and heavy breacket frasming (Beam, tee, angle,Channel, hollow sec or flat sections) including distance pieces, cleates etc complete all as specified and as directed.

S & F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe-410 W (Grade E-250) quality A complete all as specified and as directed.

S & F Mild steel screw bolts (machine made) of any dia with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n.exc. 10cm long complete all as specified and as directed.

M & L for PCC 1:2:4 type B1 using 20 mm graded stone aggregate as in copings,apex stones,bed plates etc complete all as specified and as directed

M&L for preparing new steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

Dismantling of ceiling boards including grid works fixed in any position with nails complete all as specified and as directed.

S&F aluminium flat as wind tie fixed with 50mm/75mm aluminium self tapping screws complete all as specified and as directed.

S & F anodized aluminium grid work 605 x 605 mm with using 36.5mmx23.5mmx1.5mm thick main tee, 23.5 x23.5mmx1.28mm cross tee and 25x25x1.5mm angles fixed to perimeter of wall for false ceiling including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified & directed all as specified & directed

M&L for 4mm thick Non asbestos fibre cement building boards fixed or laid / inserted to timber/ GI / Aluminium framework with screws including preparation of surfaces and applying two coats of oil emulsion distemper over a coat of primer complete all as specified and as directed.

Removing loose and broken concrete/ masonary surface by chiseling/ mechanically etc from the roof slab, coloumn, beam and similar structural members cutting edges, cleaning the dismantled portion with wire brush etc to make the reinforcement naked and remove dust, dirt and other foreign particle etc and removig to debries 50 Mtr from site all as specified

M&L for applying IPH RB -107 polymer based rust-remover (pH value –12 ) and applying IPH RB -167 Polymer based rust preventive (pH value-9) to all exposed reinforced bars complete all as specified and as directed.

M&L for applying one coat of epoxy bonding coat as per manufacture's instruction to bind with old concrete / wall surfaces of soffit of slab, coloumn, beam and similar structural members for new cement surface complete all as specified and as directed.

M&L for applying polymer modified cement mortar rendering 15mm average thick in CM 1:3 on concrete surface duly mixing polymer modifier 'Nitobond AR' of make: M/s Fosroc Chemicals India (P) Ltd. @ 10 Ltr per bag of cement or equivalent in M/s Harjas Coatings & Polymers @ 5% by wt of cement / M/s Pidilite Industries complete finished even and smooth without using extra cement all as specified and as per manufacturer's instructions.

M&L for preparation of old wooden surfaces exc. 10cm width and girth and applying one coat of synthetic enamel paint complete all as specified and as directed

M&L for preparation of old steel surfaces exc 10cm width and girth and applying one coat of synthetic enamel paint complete all as specified and as directed

Taking down chowkats or frames n.exc1.5 Sqm (with shutters & grill (if fixed) without taking off shutters from the frame) complete all as specified and as directed.

Taking down chowkats or frames exc 1.5 Sqm and n.exc 4 Sqm (with shutters and grill (if fixed) without taking off shutters from the frame) complete all as specified and as directed.

S & F solid PVC Door frame of size 50mm x 47mm made out of 5mm rudraksh colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of rudraksh colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F Anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S & F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified

S & F 4 mm plain sheet glass ordinary quality ,in square exc 0.5 sqm each complete all as specified and as directed.

S & F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples including taking down all as specified.

S & F figured glass 4 mm,pin head type and glazing with oil putty in squares n.exc 0.5 sqm in each pane complete all as specified and as directed.

S & F second class hard wood, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

M&L for cutting holes exc. half brick but not exc one brick in brick walls built in CM or cement lime mortar & stone walls built in lime mortar for inserting holdfasts & making good distrurbed portion in CM (1:3) or PCC 1:2:4 type B1 using 20mm graded stone aggregate complete all as specified and as directed.

M & L for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook & pintel hinges; large hasps & staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way & three way straps,plate washers & similar small articles conforming to Fe 290-0 Gde E-165 complete all as specified and as directed.

S & F second class hard wood 35 mm thick plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply . The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S & F second class hard wood 35 mm thick glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc divided in to squares with plain, chamfered or rounded, mitred and rebated sash bars fitted with cut and mitred beads for securing glass etc complete all as specified and as directed.

M&L preparation of new wood/wood based surfaces of exc. 10cm width or girth of any description and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

S&F Aluminium anodised sliding door bolts 250 mm long with hasp and staple complete all as specified and as directed.

S&F Aluminium anodised sliding door bolts 300mm long with hasp and staple complete all as specified and as directed..

S&F aluminium anodised barrel tower bolt of extruded section 150mm long complete all as specified and as directed..

S&F extruded aluminium alloy handle fabricated type anodised 100mm long complete all as specified and as directed..

S&F extruded aluminium alloy handle fabricated type anodised 150mm long complete all as specified and as directed..

S & F butt hinges of stainless steel 150 mm long ISI marked fixed with screws complete all as specified and as directed.

S & F butt hinges of stainless steel 100 mm long ISI marked fixed with brass screws complete all as specified and as directed.

S & F 150mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed.

S & F in replacement of 18 to 20mm thick prelaminated MDF panels of interior grade type-II with melamine finish of approved shade for kitchen cabin/wardrobe/wall panelling fixing with necessary fitting like keku fitting,spring clip,hanger plate,modular hinge/clip,push fix or stud fitting as per manufacturers instructions complete all as specified and as directed Note : SS auto hinges shall be measured and paid separately as 'Supply only"

Supply only stainless steel auto hinges of 304 grade approved make and size suitable for CB shutter complete all as specified and as directed.

S&F 30mm width continuous (piano) hinges mild steel finish or electrogalvanised complete all as specified and as directed.

S&F 100mm long hasp and staples mild steel wire type stove enamelled black including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S & F in repairs fancy type curtain rod, stainless steel,chromium plated 20/25 mm dia complete all as specified and as directed.

S & F in repair brass brackets chromium plated suitable for curtain rod 20/25 mm dia complete all as specified and as directed.

S & F Stainless Steel plate rack of size 910 mm X 960 mm of super deluxe model, suitable for 12 plates made with 22 gauge sheet and weight not less than 5.5 Kg, complete all as specified and as directed.

S&F in repair stainless steel sink with drainage board made out of 1.00 mm thick sheet with plug, washers, MS angle cantilever brackets for suitable size and connecting union to pipe of overall size 1140 mm x 500 mm and bowl size 510mm x 400 mm x 190 mm all as specified.

S&F in repairs Wash basins including brackets, Vitreous China (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and as directed..

S & F 32/40 mm (Dia of discharge pipe) Waste coupling of PTMT (half or full threaded), (Minimum weight 32mm- 45gms/40mm-60 gms) complete all as specified and as directed.

S&F PVC flexible waste pipe of 32 /40 mm, 600mm long for wash hand basin and Kitchen sink complete all as specified and as directed.

S & F in repair Bib Taps with flange, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified and as directed.

S&F in repairs angle stop valves cast copper alloy chromium plated with long shank and cup fancy type screwed down high pressure screwed both ends for pipe or union fixed for 15mm bore, complete all as specified and as directed.

S & F in repairs two way bib taps, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified and as directed.

S & F in repairs Bib Taps, long boby with flange cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified and as directed.

S&F in repairs brass chromium plated telescopic Hand shower(Health Faucet) (ABS Body) with 1.0 Meter long Easy Flex Tube in Chrome Finish& wall Hook complete all as specified and as directed.

S&F in repairs brass chromium plated shower rose with 150mm long CP shower arm 125 mm size revolving type suitable for 15 mm bore pipes complete all as specified and as directed.

S & F Soap Dish,brass chromium plated of approximate size 160 x 160 x 90 mm with screws complete all as specified and as directed.

S & F in repairs Brass Chromium Plated Tubular Towel Rail, 20mm dia, D Type, 600 mm long between flanges complete all as specified and as directed.

S & F in repairs PVC body cabinet box mirror of size 350mm X 450mm X 100mm in PTMT alloy of approved design and pattern complete all as specified and directed

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long of approved quality complete all as specified and as directed.

S & F in repairs Pillar Taps, cast copper alloy, Chromium Plated, Fancy Type, 15 mm dia, with capstan head, screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repairs Vitreous China wash down watercloset pan (pedestal pattern), white including Plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device.

S & F in repairs 10 Liters capacity, PVC Valve less, Syphonic action type, low level flushing cistern, white, with inlet ball valve, float, handle, flush pipe of polyethylene of low or high density of PVC, 32mm dia including brackets and connections to pipe of Make Slimline or Cera or equivalent make complete all as specified and as directed.

S&F in repairs PVC flexible connection with PTMT nuts, of 15mm dia and 600mm long with brass unions and rubber washers on either side, for connecting water supply line to WHB, flushtank ,Geyser etc, all as specified.

Demolition and breaking up drain pipes of size 75/100 mm dia (Salt glazed ware, AC or Reinforced concrete, PVC (SWR)) set in cement mortar complete all as specified and as directed

Dismantling of cast iron or reinforced concrete / PVC (SWR) drain pipes of size 75/100 mm dia, jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed

S & F 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls including necessary brackets, clamps as in down pipes complete all as specified and as directed.

S & F 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F 75mm bore PVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal with access door including jointing with solvent cement complete all as specified and as directed.

S&F 75mm dia PVC (SWR) bends with access door complete all as specified and as directed

S&F 75mm bore PVC [SWR] Vent Cowl including jointing with solvent cement complete all as specified and as directed.

S & F 75mm dia out let, PVC (SWR) Floor Trap with SS grating including jointing to waste pipe fixed with solvent cement complete all as specified and as directed.

S & F 110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] branch piece, single (single Y) equal or unequal with access door including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal with access door including jointing with solvent cement complete all as specified and as directed.

M &L for Stack clamps for 75mm dia bore pipe out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts andsecuring ends of stays to wall or roof complete all as specified and as directed

M &L for Stack clamps for 110 mm dia bore pipe out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts andsecuring ends of stays to wall or roof complete all as specified and as directed

S&F 100mm dia PVC (SWR) bends with access door complete all as specified and as directed

S&F 110mm bore PVC [SWR] Vent Cowl including jointing with solvent cement complete all as specified and as directed.

M & L for 75mm thick PCC 1:3:6 type C-2 using 20 mm graded stone aggregate as in sub base, plinth protection etc complete all as specified and as directed

Taking down carefully copper/aluminium point wiring (light, fan, socket or ower) complete,(fittings such as switches, ceiling roses,pendants, regulators sockets etc. making good disturbed surfaces of walls, floors, etc.

Taking down unserviceable submain wiring alongwith batten/PVC/steel conduits etc and making good disturbed surfaces of walls/ floors to match the existing surfaces all as specified

Taking down unserviceable main switches ,DBs and making good disturbed surfaces of walls/ floors to match the existing surfaces all as specified

M&L for Point wiring complete with and including 1.5 Sqmm( nominal area) single core multistranded copper conductor PVC insulated unsheathed cable 1100 volts grade I S I marked drawn into including concealed PVC Rigid Non-metallic Conduit ISI marked suitable size thickness not less 1.5 mm with accessories such as bend ,tees, junction boxes etc. incl. 1.5 Sqmm PVC insulated and unsheathed flexible muliti stranded copper conductor FR cable as continuous earthwire connected to metallic bodies of luminaries/fans etc. at one end and to common earth duly at other end including concealed PVC premoulded switch board ISI marked/3mmthick hylam sheet in MS/ PVC terminal box of suitable size for housing switch, socket and fan regulators etc complete and making good the disturbed surfaces of wall by cement patch all and matching the surface to the existing finising colour all as specified and directed for

One light point controlled by one one way switch complete all as specified and as directed

One fan point controlled by one switch complete all as specified and as directed

One switch socket 3 pin 5 Amps flush type on independent board complete all as specified and as directed.

One switch socket 3 pin 5 Amps flush type on same board complete all as specified and as directed.

One bell/ buzzer point controlled by one push button on the same board

All as per item No 131.00 above but with 2.5 sqmm FRLS cable for one socket 5 pin 15Amps flush type on independent board complete all as specified and as directed

S & F in repair Switch piano flush type single pole one way 230V, 6Amps complete all as specified and as directed

S & F in repairs Switch socket outlet 3 pin 5 Amps flush type 230V S.P. multipurpose type complete all as specified and as directed

S & F in replacement Switch socket combination flush type multi purpose 5A/16A, 5 in 1 controlled by one switch 230V complete all as specified and as directed.

S & F in replacement lamp holder ( angular type) insulated body with back plate complete all as specified and as directed

S & F in replacement ceiling rose surface PVC 50mm dia three terminals including PVC mounting block, white/lvoury /Urea finish complete all as specified and as directed.

S&F in replacement stepped type electronic fan regulator flush type on phenolic laminated sheet 100w for ceiling fan230 volt AC supply, 50HZ 1200/1400 mm sweep complete all as specified and as directed

S & F in replacement Bell push, flush type, 5 amp, one way 230V complete all as specified and as directed

S & F in replacement Bell ding dong type 230V including connections complete all as specified and as directed

M&L submain wiring with 2 single core PVC insulated multistranded flexible copper conductor 1100Volts grade (FRLS) cables 4.0 Sqmm and 1 run 4.0 Sq mm PVC insulated multistrand cu conductor cable (FRls) of green colour for continious earthing drawn through PVC surface/concealed PVC conduit of suitable size and with all accessories all as directed and specified Note: 3 run of cable and one run of conduit with accessories shall be measued as one unit

M&L for earthing complete with Galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 mir deep below GL) with top edge of earth plate not less than 1.5 Mtr below normal ground level, earth plate surrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using Galvanized earth strip 32x6 mm size connected by means of bolts, nuts, check nuts and washer of galvanized iron or steel, provision of 15 mm dia GI pipe medium grade for protection of G1 earth wire and 20mm dia GI pipe medium grade for watering arrangement and PCC (1:3:6) , type CI chamber. MS funnel, wire gauge. 50 mm thick RCC 1:2:4, type B1 earth pit cover with 6 Nos. 8 mm dia high strength deformed steel TMT bars on both ways including necessary excavation in any type of soil, returning, filling in, removal of surplus soil to distance n exc 50 mtr, provision of charcoal and salt complete all as shown in electrical plate No 3 of schedule Part-I.Note: (i) Cost of GI earth wire and GI protection pipe upto 7.5mtr length shall be deemed to be included in the rate quoted for this item. (ii) The unit rate shall also includes for Wire mesh, funnel, excavation, returninng & filling, PCC chamber pit, RCC cover & test point.(iii) PCC pit shall be provided at least 500mm away from the earth pit and not just on the earth pit. (iv) All accessories required for galvanised steel plate electrode required, as specified and as directed.

S&F in replacement MCB DB SPN sheet metal double door enclosure Concealed type of suitable size for mounting MCB 230 Volts with 200 Amps rated bus bar 8 way complete all as specified and as directed

S & F in replacement MCB SPN 6 to 32 Amps, 240Volts 10KA complete all as specified and as directed

S & F in replacement MCB SP 6 to 40 Amps, 240Volts 10KA complete all as specified and as directed

S&F in replacement LED tube light fittings 1x20w, 4 feet long, 230V decirative ultra slim square profile with extruded polycorbonate enviornmental friendly, life time 40000 buring hrs, lumen out put 2000lm, complete & pre-wired completed fixed to wall/ceiling by suitable down rod pipes and connecting to ceiling rose with stranded copper conductor incluing necessary fittings arragements complete all as specified ad as directed

Taking down ceiling fan 1200/1400 mm sweep / exhaust fans including disconnection of electric connection and removing the blades in safe for re-installing complete all as specified and as directed

Hanging only ceiling fan / exhaust fan after cleaning, greasing,oiling, assembling the blades and painting etc including replacement of 3 core cable flexible as required complete all as specified and as directed

S&F in replacement LED tube light fitting 10W, 230V, white colour complete all as specified and as directed

Supply and install in replacement hi-wall split units indoor/outdoor of capacity 1.5 Ton complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with 5 star rating inverter type and EER 3 including copper tubing with insulation 3m complete all as specified and as directed. Note : Excess copper tubing with insulation required will be measured and paid separately. Old unservicable AC shall be deposite to MES Store Yard.

S&F copper tubing of size 5/8 with insulation complete all as specified and as directed

M&L for Point wiring complete with 2.5 sqmm single core PVC insulated and PVC unsheathed (FR) multistranded copper conductor cable 1100 volt grade enclosed in and including PVC casing and capping with accessories fixed on surface on walls/ceiling by means of PVC sleeves Dash fastners and cadmium plated screws all as per ISI including sunk type boxes for mounting fitting like switches, socketes fan regulators with 3 mm thick phenolic Laminated sheet top covers concealed in walls etc including 1.5 Sqmm single core multi stranded copper conductor PVC insulated and unsheathed cable as earth continuity conductor to common earth dolly including taking down old unsv point wiring for the following:-

One 3 pin, 15 Amps socket outlet on independent board complete all as specified and as directed

One 3 pin 5/15 Amps multipin socket outlet on same board with other switch complete all as specified and as directed.

S&F socket outlet multipurpose 3 Pin 5 Amp and 2 Pin 5 Amps 250 V AC complete all as specified and as directed

M&L for concealed sub main wiring with two run single core 6 Sqmm and one run of 6 Sq mm as earth continuity conductor 1100 V grade PVC insulated unsheathed FRLS grade copper conductor cable single core multistranded ISI matked (IS-694) drawn through and including PVC casing capping of suitab/ conduit of suitable size ISI marked .includig connected acessories such bend support etc laid in wall/roof/ floor including taking down old unsv wiring etc complete all as specified and as directed Note: 3 run of cable and one run of conduit with accessories shall be measued as one unit

S & F in replacement double pole and earth enclosure with a three pin and earth plug with socket 32A capacity including one double pole MCB 32A capacity all as directed.

Supply and install in replacement of fully stainless steel water cooler electric driven (single phase), having approx stroge capacity of 80 ltrs and nominal coooling capacity of 40 ltrs per hours, Electric driven (single phase, 50HZ) with diamensions Width 460 x Depth 580 x Height 1440 with following specifications (a) Power Supply (V/Hz/Ph) 230 Volts ± 10%, 50 Hz, single phase (b) Cooling Capacity : 40 Ltr/ hr , (c) Number of cold water outlets : 2 Nos, (d) Refrigerant : R 134a / R22 ( Ecofriendly), (e) Condenser fan Propeller type: Quiet, (f) Thermostat Automatically controls temperature, (g) Inlet 12.7 mm BSP connection, (h) Drain 25.4 and 12.7 mm BSP connection and with following accessories complete , (j) Voltage stablizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170V to 250 V with output voltage stablized at 230 V with accuracy of + 2.5% and capacity 2 KVA complete, (k) S&F GI pipe 15mm dia medium grade with fittings laid in tranches/wall complete all as specified : 8.6 RM, (l) S&F Ball valves high pressure of PTMT with lepoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed (Minimum wieght 15mm 142 gms/20mm - 210 gm/25mm - 455g - 01 No, (m) S&F Gate valve 15mm dia screwed both ends for pipe and fixed complete all as specified - 01 Nos

Supply and install in replacement of fully stainless steel water cooler electric driven (single phase), having approx stroge capacity of 120 ltrs and nominal coooling capacity of 60 ltrs per hours, Electric driven (single phase, 50HZ) with following specifications (a) Power Supply (V/Hz/Ph) 230 Volts ± 10%, 50 Hz, single phase (b) Cooling Capacity : 60 Ltr/ hr , (c) Number of cold water outlets : 2 Nos, (d) Refrigerant : R 134a / R22 ( Ecofriendly), (e) Condenser fan Propeller type: Quiet, (f) Thermostat Automatically controls temperature, (g) Inlet 12.7 mm BSP connection, (h) Drain 25.4 and 12.7 mm BSP connection and with following accessories complete , (j) Voltage stablizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170V to 250 V with output voltage stablized at 230 V with accuracy of + 2.5% and capacity 2 KVA complete, (k) S&F GI pipe 15mm dia medium grade with fittings laid in tranches/wall complete all as specified : 8.6 RM, (l) S&F Ball valves high pressure of PTMT with lepoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed (Minimum wieght 15mm 142 gms/20mm - 210 gm/25mm - 455g - 01 No, (m) S&F Gate valve 15mm dia screwed both ends for pipe and fixed complete all as specified - 01 Nos

Supply and fix CPVC pipe 20mm condensing water flow pipe and water supply connection to water cooler including necessary clamping required all as directed at site

M/s Pooja Enterprises

Kathir Marketing Services

Allied Trading Company