8144/2022-23/E8 SPECIAL REPAIR TO BELG T-58 AND T-32 (JCOS/OR LIVING) IN 10 BIHAR AND SPL REPAIR TO BLDG NO T-43 NEAR MI ROOM OF 303 FD HOSP AND PROVN OF FOUR URINAL BLOCKS AT 275 ASC COY UNDER GE 860 EWS

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for coloured Non Skid Ceramic joint free tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in cement mortar 1:6 all as directed .

M&L for coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and as directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed.

S & F for 0.63 mm Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with fixed with L-type or J-type or cranked hook bolts in lieu of screws complete all as specified and as directed.

All as per Item No-05 here-in-before but except sheeting (any thickness)

All as per Srl Item No 5 here-in-before but plain sheet

M&L for preparing of new steel surfaces over 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for preparing of old steel surfaces over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Demolition of cement concrete in ground floor and paving n.exc 15 cm thick below and above GL level (Unreinforced) complete all as specified and directed.

M&L for plain cement concrete (1:3:6) type C-2 (using 40mm graded crushed stone aggregates) 75 mm thick as in plinth protection/PCC Path complete all as specified and as directed

Hacking out old broken glass (any thickness, size, quality or escription) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and as directed.

M&L for 3mm thk sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq m in each panecomplete all as specified and directed by Engr-in-charge.

M&L for Rendering 15mm thick 1:4 cement mortar on fair faces of brick work or concrete surfaces

Dismantling water tanks exc 500ltr but not exc 1000ltr and removing to store.

S&F for Rotational moulded polyethylene water storage tanks 1000ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I.

Taking up or down steel tubing 20mm dia and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

M&L for steel water tubing 20 mm dia medium grade galvanised with all fitting and fixed all complete to wall and ceiling or laid in froor complete all as specified and as directed.

Refixing old steel tubing 20mm and connection in new or old position (wall, ceiling and floor etc) complete all as specified and as directed.

Taking up or down steel tubing 15mm dia and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

M&L for steel water tubing 15 mm dia medium grade galvanised with all fitting and fixed all complete to wall and ceiling or laid in froor complete all as specified and as directed.

Refixing old steel tubing 15 mm dia and connection in new or old position (wall, ceiling and floor etc) complete all as specified and as directed.

S&F in repairs for 15mm Bib taps, cromium plated, fency type screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F in repairs for 15mm stop volves, chromium plated, fency type screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F in repairs Pillar taps, fency type 15mm, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F for PVC connections 15mm size with PTMT nuts of length 450mm

S&F in repairs 100mm dia Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)

S&F in repairs vitreous china water closet (Squatt Pan) Orrisa pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe' complete all as specified and directed including 100mm CI/PVC 'P' trap complete all as specified and as directed.

S & F in repairs for Vitreous China bowl type urinals, size of 465x355x265mm white(minimum) with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (excluding of fixing supply pipe, flushing cistern, flush pipe, trap and waste pipe) complete all as specified and directed.

S&F in repair viterous China wash basin, white, flat back, size 630X450mm incl waste coupling CP 32mm dia brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specfied and directed. (Make : Jaquar/Cera)

S&F in repair 10 ltr capacity PVC low level flushing cistern with ball valve and handle/push button 32mm dia PVC flush pipe complete all as specified and as directed

S&F in repairs grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and as directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc and n.exc 10 Sqm on plan and getting out in hard/dense soil complete all as specified and directed.

Returning filling in incl spreading leveling, watering, and well, ramming in layer n.exc 25 cm in layers in hard/dense soil complete all as specified and directed.

Removing excavated material (soil) to a distance n. exc50 m and depositing where directed at a level n. exc 1.50 m above the starting point complete all as specified and directed.

Demolition and breaking up drain pipes (SGSW, AC or reinforced concrete) set in cement mortar internal dia of pipe 150 mm, complete all as specified and directed.

M&L Concrete bed 1:4:8 type D-2 to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested bore of pipe in 150mm complete all as specified and as directed.

S&F 150mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches complete all as specified.

Demolition and breaking up drain pipes (SGSW, AC or reinforced concrete) set in cement mortar internal dia of pipe 75 mm, in any position complete all as specified and directed.

S&F 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to floors complete all as specified and as directed.

S&F 75 mm dia bore PVC (SWR) bends any radius, complete all as specified and directed.

Demolition of stone/PCC block/boulder masonry built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed..

M&L for Pre-cast cement concrete block masonry Type C-1 (1:3:6) 20 mm graded aggregate with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L for Plain cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in coping, benching bed plates and the line including necessary form work and finishing all exposed surface of concrete as per clause 4.11.16.2(a) of SSR Part-I(1991) complete all as specified and as directed.

Rendering 10mm thick in CM 1:4 using water proofing compound as per manufacturer's instruction, finished even and smooth surface without using extra cement (WPC measured and paid separately) complete all as specified and directed.

Supply only Integral water proofing compound for external plaster complete all as specified and directed.

Excavating over areas, n.exc 1.5 m deep and getting out in hard/dense soil complete all as specified and as directed.

Excavating over areas, exc 1.5 m deep and n, exc 3.00 m deep getting out in hard/dense soil complete all as specified and as directed.

M & L for PCC 1:4:8 type D -2 ( Nominalmix) using 40 mm graded stone aggregate as in foundation filling and similar work complete all as specified and as directed.

M&L for walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4 complete all as specified and as directed.

M&L for walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted, laid dry complete all as specified and as directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; for rough finish and flat surfaces not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, rough finished surfaces of concrete complete all as specified and as directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M & L for providing RCC M- 25 (design mix) (using 20mm graded crushed stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Dismantling wall & ceiling boards (fibre, insulation etc ) or insulation boards, slabs, blankets any thick ness including cover fillets complete all as specified and directed.

S&F grid false ceiling GI system powder coated prelude (main runner sec 32x24x0.30x3600mm, cross tee 25x24x0.30x1200mm, wall angle 24x24x0.40x3000mm and including providing and fixing 4mm thick non asbestos cement fibre designer (E-board) size 595x595mm fixed in ceiling frame work complete all as specified and directed (Make : E-board, Armstrong, Everest, Saint, Gobain).

M&L 9 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work in walls complete all as specified and as directed.

Dismantling of timber fillet under 40 Sq cm in section in framed work complete all as specified and directed.

M&L second class hard wood timber scantling plain fillets, square, rectangular or triangular in section clear swan, sectional area exc 13 sqcm & not exc 25 sqcm, secured with nails or brads complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type BO (Using 12.5mm graded crushed stone aggregate) as in floor levelling and finished even and fair without using extra cement complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

M & L mild steel Roof trusses (framed), trussed, purlins, crane gantries, rails, post, bracing and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) confirming to Fe 410 -W (Gde?E- 250 )quality complete all as specified and as directed.

Taking down chowkats with shutters without taking off shutter from frame area exc 1.5 but not exc 4.00 sqm complete all as specified and directed.

Taking down chowkats with shutters without taking off shutter from frame area n. exc 1.5sqm complete all as specified and directed.

S&F 2nd Class hard wood as in chowkhats or frames, rebated on solid rounded or chamfered, put toghether with glue, pinned at joints complete all as specified and directed.

S&F 35mm thick plain framed paneled shutter (any no of panels) with panels of veneer particle board medium density, wood particles board with commercial ply face veneers and fitted to chowkhats all as specified of 2nd class hard wood. complete all as specified and directed.

S&F 30 mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part I,Section 8, clouse 8.24 (a);fitted to chowkats. complete all as specified and directed.

S&F 150mm long extruded aluminium alloy handle cast type complete all as specified and directed.

S&F 100mm long extruded aluminium alloy handle cast type complete all as specified and directed.

S&F 100 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F 75 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S& F MS Butt Hinges medium weight, cold rolled 100 mm size complete all as specified and directed.

S& F MS Butt Hinges medium weight, cold rolled 75 mm size complete all as specified and directed.

S&F Mild steel sliding door bolt, stove enamelled black with bright bolts not less than 12mm daia with and incl min 6 Nos of bolt & nuts , four on bolt plate and two on staple plate 300 mm size complete all as specified and directed.

S&F in repair of aluminum body door closer (extruded section) hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed by Engr-in-Charge.

M&L for painting two coats of synthetic enamel paint over one coat of pink primer incl necessary preparation of new wooden surface of any description over 10 cm width or girth complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry (1:3:6) C-1 20mm graded aggregate, with solid blocks, n exc. 10 cm in width and setting in 1:6 cement mortar, complete

M&L for Rendering 10mm thick 1:6 cement mortar on fair faces of brick work or concrete surfaces

M&L for preparation of new plaster surfaces and applying three coat of white wash on wall complete all as soecified and as directed.

M&L for preparation of new plaster surfaces and applying two coat of cement base paint over a coat of primer complete all as soecified and as directed.

S&F for Unplasticised PVC pipes 20mm dia of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and as directed.

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe complete all as specified and as directed.

S&F Joist, channel, angle, or tee sections,fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified and as directed.

M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for 75mm Cement concrete type D- 2, 1:4:8 (40mm graded crushed stone aggregate complete all as specified and as directed.

M&L for Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in Cement mortar 1:6 complete all as specified and as directed.

Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for Rendering 10mm thick in cement mortar 1:6 on stone masonry surfaces or surface other than fair face of brick-work or backing coat to receive tiles complete all as specified and as directed.

Rendering 10mm thick on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing rendering is to be finished even and smooth (without using extra lime or cement) using Cement mortar 1:6 complete all as specified and as directed.

Rendering 15mm thick on fair faces of brick work or concrete surfaces rendering is to be finished even and smooth (without using extra lime or cement) using Cement mortar 1:4 complete all as specified and as directed.

S&F 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

M&L Concrete bed 1:4:8 type D-2 to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested bore of pipe in 150mm complete all as specified and as directed.

Providing precast ce- ment concrete 1:2:4 type B-1 (20mm graded aggregate) in win- dow or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin) corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to match

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings, tube light fittings etc complete and removing all retrieved materials to MES stores for segregation of serviceable /Unserviceable fitting&fixture and also making good disturbed surfaces of wall, floors etc complete all asspecified and as directed by the Engineer-in-Charge.

Material and labour for point wiring with 1.5 Sqmm copper conductor (Multi-standard) PVC insulated and unsheathed electric cable 1100 volts in and including PVC casing and capping of 25 mm and above (as per conductor run )with all fittings/ accessories and including PVC insulated and unsheathed electric cable 1100 volts1.5 Sqmm FRLS (multi-stranded) copper conductor single core( Green colour) cable as continuous earth wire connected to common earth dolly including 50 mm deep box made of 2nd class hard board of required size and shape etc covered with 3 mm thick plastic laminated sheet ( Make Hylum) for one light point independent controlled by one, one way switch complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing switch piano flush button single pole one way 5 Amps complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing angular lamp holder, metal cased body of brass with back plate with and including 09 watt LED Bulb for batten fittings, including Plastic square box of required size complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge.

Supply and fixing LED lights fitting 1x 16W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm.

Supply and fixing sheet Metal enclosure double shutter type for DB’s 240 Volts Single Pole and Neutral 8 way with 200 Amps rated bus bar complete including wooden board of required size duly painted with matching colour paint acomplete all as specified and as directed by the Engr-in-Charge.

Supply and fixing SPN 40 to 63 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning.

Supply and fixing SP 5 to 32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with stranded conductgor PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 10 sq. mm 2 core nominal cross section in service connections.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 3 of SSR 2009 Part-I and connecting to MCBDB’s earth test point all as specified or indicated including testing on completion .

All as per item No 108 here in before but for one 3 pin socket outlet 5 Amp on same board complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 108 here in before but for one 3 pin socket outlet 5 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 108 here in before but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing socket outlet multipurpose 2 pin and 3 pin, 5 Amp, flush type complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing switch socket combination multi purpose 2 in 1, 3 pin 5 Amp and 15 Amp, flush type complete all as specified and as directed by Engr-in-charge.

M/S LIBE & CO

SHANTI ENTERPRISES

M/S TRADE LINK

M/s Koul & Sons