Provn of certain sanctioned Minor and Revenue works in the area of AGE B/R-1 and AGE E/M under GE (West) Delhi Cantt-10

Surface excavation n exc 30cm deep and averaging 15cm deep including getting out in any type of soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Filling under floor, spreading and levelling in layers n exc 25cm thick well raming including watering as requred complete all as specified and directed

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface complete all as specified and directed.

M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface under sub base flooring or plinth protection etc. complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for RCC M25 design mix, using 20mm graded stone aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&l for RCC M25 design mix, using 20mm graded stone aggregate in Columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for RCC M25 design mix using 20mm graded stone aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for RCC M25 design mix using 20mm graded stone aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for RCC M25 design mix using 20mm graded stone aggregate in Chajjas complete all as specified and directed.

Use and waste for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

Use and waste for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.for rough finish surface complete all as specified and directed.

Use and waste for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finish surface complete all as specified and as directed.

Formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide. (Where RCC/PCC band in walls, spanning and opening, complete all as specified and as directed.

Use and waste for Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and as directed.

Use and waste Formwork to sides of pillars,posts, struts, piers, columns and stanchions complete all as specified and as directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Ditto as per item no 20 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base flooring complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2 (40mm graded agg) for plinth protection laid in bays and finished even and fair incl filling the joint with bitumen mastic complete all as specified and directed .

M&L for PCC 1:3:6 type C-2 (20 mm graded agg) as in surface channel/drain / haunching of manhole etc. complete all as specified and as directed.

M&L for Glazed ceramic tiles in vertical surface 300x450x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick screed bedding/backing in CM 1:4 complete all as specified and as directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thic screed bedding layer in CM 1:6 complete all as specified and as directed.

M&L for vitreous china wash hand basin flat back size 550x400 mm size white excluding taps waste chain and plug and porcelain stopper but including brackets and 32mm dia waste fittings brass chromium plated with long screwd shanks and fly nuts, 32x600mm long PVC waste pipe complete all as specified and as directed.

M&L for Ready Mix plaster 15mm thick on brick or concrete surface of internal and external walls finished even and fair surface without using extra cement complete all as specified and as directed.

M&L for 15mm thick cement plaster on brick or concrete surface in CM 1:4 finished even and smooth surface using extra cement complete all as specified and as directed.

M&L for Ready Mix plaster 5mm thick on concrete surface of ceiling finished even and fair surface without using extra cement complete all as specified and as directed.

M&L for brick work in cement morta 1:6 using sub class B bricks, straight or curved on plan exc 6mtr mean radius complete all as specified and directed.

M&L for 40mm thick DPC on horizontal or vertical surface in PCC 1:2:4 type B0 using 12.5mm graded stone aggregate including necessary formwork and using WPC as per Manufacturer insruction complete all as specified and directed.

Preparation of newly plastered surface on wall and applying two coats of cement based paint over one coat of primer white or tinted complete

Ditto as per Item no 33 above but three coats of white lime wash or tinted complete

Ditto as per Item no 33 above but three coats of white lime wash on ceiling complete

M&L for water proofing treatment to roof surface with APP water proofing membrane 3mm thick & weighing not less than 3.0 kg/sqm of approved make black finish & reinforced with non woven polyester matt of min 150 gm/sqm laid over a coat of bitumen primer conforming to IS-3384 @ 0.4 Ltr/sqm over prepared roof surfaces, forcing overlap with a propane or a butane gas torch with a overlap of 75mm at sides & 100mm at ends & sealing as per manufacturer's instructions incl 2coat of aluminium paint over complete treated surface complete all as spd and directed. Note :- 1. Water proofing treatment shall be got carried out by the manufacturer or their authorised applicator only. 2. Bitumen primer, bitumen and membrane shall be of same make/manufacturer. 3. The APP Membrane to be inserted in the parapet wall/wall by cutting chases of atleast 65X50mm size & making good in CM 1:3. complete all as specified and directed.

M&L for rendering 10mm thick cement mortar 1:4 on fair face of brick work or concrete surface on wall/roof surface including using WPC as per manufacturer instruction complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 ,bed concrete to 150mm bore dia drain pipes (of 100mm thick) including packing under, and haunching against the sides of pipes after they are laid and tested; complete all as specified and directed.

M&L for 150mm bore Salt-glazed stoneware drain pipes laid in trenches and jointed complete all as specified and directed.

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in coping, bed plates, kerbs including weathering slightly rounded or chamfered and throating complete all as specified and directed.

M&L for 75mm thick SFRC manhole/drain cover size not exc 1.00sqm each set and jonted in cement mortar 1:4 complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F 100mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolt extruded section complete all as specified and directed.

S&F 150mm long extruded aluminium alloy handle complete all as specified and directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F 4mm thick pin headed, figured glass with oil putty in square n exc 0.50 sq m in each pane complete all as specified and directed.

M&L for preparation of new steel surface and applying two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L 20mm CPVC pipes SDR 11 with all plain CPVC SDR 11 and brass elbow, Tee, MTA/BTA Adeptor,tank adeptor etc. CPVC fittings and fixed complete to walls, ceiling or laid in floor complete all as spd and directed.

M&L 25mm CPVC pipes SDR 11 with all plain CPVC SDR 11 and brass elbow, Tee, MTA/BTA Adeptor,tank adeptor etc. CPVC fittings and fixed complete to walls, ceiling or laid in floor complete all as spd and directed.

S&F for 500 ltr capacity rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F 20mm float ball valve high pressure of PTMT with epoxy coted aluminium rod & high density plastic bal serewed for ison pipe complete all as specified.

S&F brass body chromium plated fancy type health faucet with chromium plated 1mtr long pipe complete all as specified and directed.

S&F in repair vitreous china white european type WC with "P" or "S" trap including connection to drain pipes, traps and PVC flushing cistern with pipe 32mm dia PVC flush pipe including PVC seat cover and fixing bolts complete all as specified and directed.

M&L for Bib tap fancy type, chromium plated for 15mm bore of pipe, cast copper alloy with crutch or butter fly handle, screwed for iron pipe complete all as specified and directed.

M&L for stop vale/angle vave cast copper alloy chroumium plated fancy type for 15mm bore dia of pipe complete all as specified and directed.

S&F 15mm bore dia pillar tape cast copper alloy chromium plated fancy type screwed down for high pressure pipe complete all as specified and directed.

S&F 15mm nominal internal bore PVC connection 450mm long with two brass nuts and PVC washers complete all as specified and directed.

S&F for brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

M&L for 75mm out let diaPVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socket in any length with rubber ring joints, fixed to wall or laid in trenches complete all as specified and directed.

S&F in 75mm bore PVC (SWR) bends any radius all as specified and directed.

S&F in 75mm bore PVC (SWR) bends with acess door any radius all as specified and directed

M&L for 110mm bore PVC (SWR) pipe conforming to relevant IS single socketed in any length with rubber ring joint and fixed to wall complete incl taking down old rain water pipes complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius all as specified and directed

S&F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal with acess door any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) vent cpwl any radius complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 sq. m but n exc 4 sq. m each ccomplete all as specified and directed.

M&L for powder coated Anodised aluminium frame for doors, windows, ventilators, grill, partitions, sliding tracks, aluminium section for shutters suitable for two/three/four track window and aluminium section sliding members incl all necessary fittings and fixtures, jointing cleats, rubber packing etc complete all as specified and directed.

M&L for powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing,(handles 2 Nos in each door, 15mm aluminium hinges-3 Nos each door, 15mm Aluminium tower bolt 02 Nos each door), anodised aluminum snap beading screws etc. complete all as specified and directed.

M&L for stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apperture 1.40 mm fixed to door / window (steel/wooden) complete all as specified & directed.

S&F in repair chromium plated stanless steel curtain rod 25mm bore fixed with fixing brackets,stops, rollers etc complete all as specified and directed.

S&F for drapery rod's side bulb stainless steel chromium plated suitable for 25mm bore curtain rod complete all as specified and directed.

S&F in repair coated MS drapery rod's brackets as required complete all as specified and directed complete all as specified and directed.

M&L for 20mm thick, granite (of any type) work (table rubbed and polished) in window-cills, cooking platforms and like in 15mm tihck cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as directed.

S&F Solid PVC Wall Lining/penelling consisting of 5mm thick single side prelam PVC sheet used instead of plain colour sheet inclusive of solvent cement and fixing at site on PVC frame including 5mm thick PVC sheet fillet of width 35mm for wall paneling at distance of exceeding 30cm centre tor centre on verticl and at every end or joint of sheet in horizontal/vertical cinclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in any type soil and removing debrish beyond MOD land complete all as specified and directed.

PCC 1:2:4 type B1 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specificed and as directed by Engr-in-Charge.

M&L for sand bedding/cushioning under interlocking tiles floor complete all as specified and directed.

M&L for minimum 60mm thick precast PCC interlocking blocks of grade M-40 single layer monolithic high density manufactured by electro vibro hydraulically operated block making machine confirming to IS-15658 : 2006 in glossy finished coloured tile to make a pattern as directed,complete all as specified and directed.

M&L for mild steel work with square/rectangular section in post, Roof trusses (framed), trussed, purlins, rafter, crane gantries, wind ties, rails and fastenings and heavy bracket, framing of tube sections including distance pieces, cleats, MS plates, nut & bolts etc complete all as specified and as directed.

M&L for preparation of new steel & iron surfaces of any description over 10cm in width or girth not otherwise described and applying two coats of syntethic enamel paint over a coat of red oxide primer complete all as specified & directed.

S&F of Pre-painted galvalume aluminium zinc coating (150 GSM) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and as directed by Engr-in-Charge.

Extra for forming fair finished drain or channel 75 cm inner girth in cement concrete, using extra cement, including forms, mounds, mitred/stopped end etc. complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in Ramp laid in bays and finished even and fair incl filling the joint with bitumens mastic complete all as specified and directed.

M & L for hard core of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed.

S&F pre cast concrete block for kerb stone with solid block ex 10cm in width type B1, 1:2:4 (using 20mm graded stone aggregate ) set in CM 1:6 of any shape and size. Kerb stone shall be fixed in true line and level or incurves for edging of road side path including embedding in ground to any depth as reqd complete all as specified and directed.

S & F of box type steel window with side hung shutters including box type hinges with steel handle, hold fast and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

Ditto as per item no. 92 above but without glazing bars complete all as specified.

S&F for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors/door frames; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as spd and directed.

S & F for 35mm thick 2nd plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers complete all as specified.

S & F of 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares, with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter is as specified in clause No. 8.24 (a) of MES schedule 2009, part – I (Specifications) complete all as specified.

M & L for Earthing complete with copper plate 60×60cm ×3.15mm thick electrode, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to 20×3.15 mm copper strip as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel, connected to earthing test point, earth lead protected by medium grade 32 mm dia GI pipe connected to main control board and GI pipe medium grade 20mm bore for watering and including funnel, wire mesh, RCC pit cover and PCC chamber pit with PCC 1:2:4 B-1 ( including excavation and earth work, disposal of surplus soil to a distance not exc. 50 Mtrs) all as specified and directed. Note:-(a). PCC pit shall be provided at list 500 mm away from the earth pit and not just on the earth pit and extra cost of additional length of water pipe and fittings, junction, elbow etc shall be deemed to be included in the unit rate. (b). RCC pit cover shall be of pre-cast RCC 1:2:4, type B-1, 80 mm thick reinforced with XPM weighing not less than 4 Kg/ Sq m in lieu of cast iron cover all as specified or indicated including testing on completion all as specified and directed.

S&F Air termination, single pointed, copper rod 12mm dia and 300mm long complete all as specified and directed.

S&F of copper strip of size 20 x 3.15 mm with saddles/ insulators/ fixing screws etc. for roof conducters and down conducters above ground, complete all as specified and directed. Note: Insulator should be used for every running metre of roof and down conductor complete all as specified and directed.

S&F test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed, complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M&L point wiring complete with 1.5 Sqm single core PVC insulated unsheathed FRLS cable 1100 volts grade (ISI marked) with multi stranded copper conductor drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI) marked concealed in wall/fixed to roof, ceiling etc and incl provn of 1.5 sqmm PVC insulated multistranded unsheathed copper conductor cable FRLS (ISI marked) as earth continuity conductor, fabricated sunken terminal box made out of 1.60 mm thick sheet steel duly painted concealed in walls, with 3mm thick bakelite/PVC sheet ISI marked top cover with brass/chromium plated screws and cup washers for housing switches, socket outlets, fan regulators etc, all as specified and as directed.

(a) One light /Ceiling fan/exhaust fan point controlled by one switch.

(b) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on independent board.

(c) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on same board

M&L point wiring with PVC unsheathed multi stranded copper conductor cable 2.5 sqmm FRLS 1100 Volts in New PVC concealed conduit medium grade ISI Marked not less than 20 mm dia in new M S steel terminal boxes modular including one run of using 2.5 sqmm FRLS 1100 Volts copper conductor cable as earth continuity connected to common earth for one 15 A switch socket power point, all as specified

M&L switch Modular type 6 Amp SP one way ISI marked complete all as specified

M&L switch Modular type type 16 Amp SP one way, ISI marked complete all as specified

M&LModular type socket outlet 5 pin 6 Amp flush type, ISI marked complete all as specified

M&L Modular type socket outlet 2 in 1,5 pin 6/16 Amps, ISI marked complete all as specified

M&L ceiling rose 3 phase PVC polycorbonate,isolated body, complete all as specified

S & F Modular electronic fan regulator step type,2 module ,360 degree rotation complete all as specified and directed by engr-in charge.

M&L for earthing of machinery/equipment/panel/installed at power house/subatation, complete with galvanised steel earth palte electrode 600 x 600 x 6 mm thick buried directly in ground (Earth pit not less than 2.5 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connecting to galvanised iron strip 25 x 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel and earth protected by 40 mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electrical plate No.3 of SSR Part-I )2009) and testing on completion all as specified and directed.

Supply and fix in replacement MCB DB SPN 12 way Horizontal, IP - 43 Protection double door 240 V AC 50Hz with for MCB SPN as incomer and SP MCBs as out going with tinned copper bus bar ,neutral link earth link complete all as specified and directed.

M&L MCB SPN 40 Amp "B" curve, 10 kA complete all as specified and directed.

M&L MCB SP 6 to 32 Amp "B" curve ,10 kA. complete all as specified and directed.

Supply and fix in replacement LED batten luminaire surface mounted, 4 feet system wattage of 20 Watts with lifetime of 50000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.90, THD< 20%, colour temperature - 6500K, surge protection 3KV in CM, IP-20 protected, meets LED IS specifications, Class - 1, Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 DegreeC, system efficacy at luminarie level > 105 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete all as specified and directed.

Supply and fix in replacement LED batten luminaire surface mounted, 2 feet system wattage of 10 Watts with lifetime of 50000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.90, THD< 20%, colour temperature - 6500K, surge protection 3KV in CM, IP-20 protected, meets LED IS specifications, Class - 1, Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 DegreeC, system efficacy at luminarie level > 105 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete all as specified and directed.

Supply and fix in replacement 10 watts bulkhead fitting with powder coated die cast aluminium housing with glass/ non yellowing polycarbonate cover, IP65 Protection, System level efficacy of the Luminary - is >100lm/W with a life class of 25,000 burning hours at L70 criteria, Power Factor >0.95, driver with Voltage range 150-270V, Temperature range 0 to 50 Deg, Driver efficiency >85%,THD<20%, CRI>80, Color Temperature-6500K, Surge protection of 4.0 KV, including connecting up with necessary PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed complete all as specified and directed.

Supply and fixing new BLDC fan against old ceiling fans three blade, Robust and reliable inverter motor (brush less DC Motor) powered by ECM technology, BEE 5 star rating for energy saving, rated Air delivery >220 cum/min, AC single phase 230/240 V of size 1200 mm sweep including making connection with three core flexible, copper cable pvc insulated of suitable length, complete all as directed. Note BLDC Fan should work on existing electronic fan regulator.

Provn of modular box type metal enclosure single pole and Neutral with a two pin earth plug and socket complete with a MCB SP 20 Amp 220 volts, 50 Hz, 10KA breaking capacity, including fixing completly in wall with sutable sand and cement, complete all as specified and directed.

Provn of water heater storage type Geyser vertical type with suitable size of fastner and including provision and connecting up of SS braidedpipe with adopter for inlet and outlet water connection having edjustable knob for temperature control and inner tank should be glass line coated, capacity 25 Ltrs, having heating element 1.5 KW and not less than 5 star rating, suitable for ,230 volt, 50 Hz electric supply complete all as specified and directed .

S&f in replacemnt exhaust fans metal body AC single phase 230/240 V of size 300 mm sweep, Air flow rate > 900cum/min, Bird screen for protection against birds, double ball bearing, metal body with louvre with louvre for fixing of exhaust fan complete all as directed by Engr-in-Charge.

S & F in replacement pressure die cast aluminium housing LED street light luminaires with IP66 deg. of protection suitable for 40 watt LED fitting duly fixed on 40 mm dia GI mast including 50X 6 mm thick MS flat with suitable size of fastner including making connection flexible copper conductor cable from ceiling rose to fitting complete all as specified and directed. Note : The Contractor quoated the rates incl all accessories like suitable GI pipe mast, 50x6 mm thick MS flat, fashner, nut & bolts, suitable length of flexiable wire complete all as specified and directed.

Supply and fixing new BLDC fan against old ceiling fans three blade, Robust and reliable inverter motor (brush less DC Motor) powered by ECM technology, BEE 5 star rating for energy saving, rated Air delivery >220 cum/min, AC single phase 230/240 V of size 1200 mm sweep including making connection with three core flexible, copper cable pvc insulated of suitable length, complete all as directed. Note BLDC Fan should work on existing electronic fan regulator.

Provn of modular box type metal enclosure single pole and Neutral with a two pin earth plug and socket complete with a MCB SP 20 Amp 220 volts, 50 Hz, 10KA breaking capacity, including fixing completly in wall with sutable sand and cement, complete all as specified and directed.

Provn of water heater storage type Geyser vertical type with suitable size of fastner and including provision and connecting up of SS braidedpipe with adopter for inlet and outlet water connection having edjustable knob for temperature control and inner tank should be glass line coated, capacity 25 Ltrs, having heating element 1.5 KW and not less than 5 star rating, suitable for ,230 volt, 50 Hz electric supply complete all as specified and directed .

S & F in replacement pressure die cast aluminium housing LED street light luminaires with IP66 deg. of protection suitable for 35 watt LED fitting duly fixed on 40 mm dia GI mast including 50X 6 mm thick MS flat with suitable size of fastner including making connection flexible copper conductor cable from ceiling rose to fitting complete all as specified and directed. Note : The Contractor quoated the rates incl all accessories like suitable GI pipe mast, 50x6 mm thick MS flat, fashner, nut & bolts, suitable length of flexiable wire complete all as specified and directed by engr-in charge.

Provn of Wall mounted fans AC single phase 230/240 V, of size 400 mm sweep, speed RPM 1400,Sturdy and shock proof body for fixing of wall fan complete all as specified and directed by engr-in charge.

Provn of LED 2 X 2 ft backlite surface mounted fitting 36/40 Watts including connecting up with necessary PVC sheathed 3 core 1.5 Sqmm copper conductor flexible wire fixed complete all as specified and directed by engr-in charge.

Supply & fix in repair factory made epoxy powder coated Distribution Board VTPN-4 ways with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removeable gland plates with knockouts and suitable for one VTPN- MCCB 125/160 Amp as incomer and 40 to 63 Amp SP MCBs outgoing complete all as specified and conforming to IS : 8623. complete all as specified and directed by engr-in charge.

M&L in replacement MCCB 125 Amps, 16 KA , 4P, 415 Volts, 50Hz , with thermal magnetic setting complete all as specified and directed by engr-in charge.

S&F modular type AC box single pole and Neutral with a two pin earth plug and socket complete with a mini MCB SP 20 Amp 220 volts, 50 Hz, 10KA breaking capacity, including fixing completly in wall with sutable sand and cement, complete all as specified and directed.

S & F water heater storage type Geyser vertical type with suitable size of fastner and, inner tank material of superior glass line tank and outer body material of ABS with high pressure with standing enabling (up to 8 bar pressure) capacity including provision and connecting up of SS braidedpipe with adopter for inlet and outlet wwater connection having edjustable knob for temperature control and inner tank should be glass line coated, capacity 25 Ltrs, having heating element 1.5 KW and not less than 5 star rating, suitable for ,230 volt, 50 Hz electric supply complete all as specified and directed .