PROVN OF LABORATORY IN KENDRIYA VIDYALAYA NO. 1 AT AIRFORCE STATION SURATGARH

Amount

BOQ (PROVN OF LABORATORIES IN KENDRIYA VIDYALAYA NO. 1 AT AIRFORCE STATION SURATGARH)

Surface excavation not exceeding 30cm and average 15 cm deep and getting out in soft /loose soil complete all as specified and as directed.

Excavation in trenches, not exc 1.5 m wide and not exc 1.5 m in depth; for foundation, etc. or manholes, pier holes, etc. not exc 10 sqm on plan and getting out in soft loose soil complete all as specified and directed.

All as per Sr item no 2 but depth exc 1.5 mtr but not exceeding 3.0 mtr.

Forming embankment including raising earth, spreading in layers not exc. 30 cm thick, watering, ramming (rolling and finishing to reqd size not exc 1.5 mtr high from base). Complete all as specified and directed.

Returning, filling in,including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft loose soil, complete all as specified and directed.

Removing excavated material not exc. 50m and depositing where directed at a level not exc. 1.5 m above the starting point, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cm 1 : 6 complete all as specified and as directed by Engr-in-Charge.

M&L for 75mm thick plain cement concrete 1:3:6, type C2, using 40mm graded crushed stone aggregate as in plinth protection, laid in slope of 1:12 and surface finished even and smooth without using extra cement including making joint at 2.5m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth (comprising one part hot blown bitumen 85/25 and two part of sand), complete all as specified and directed.

M&L for 75mm thick Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) in sub base,flooring, pavings etc complete all as specified and as directed.

M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundations, filling & mass concrete. Complete all as specified and directed.

M&L of Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

M&L of Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and as directed.

M&L of Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed.

M&L of Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

M&L of Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and as directed.

M&L for reinforced cement concrete M-25 (design mix) using 20 mm graded aggregate) as in slab supported on wall, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves. complete all as specified

All as per item No 16 here in before but RCC M-25 (Design Mix) as in Column/Pillar. complete all as specified and directed.

same as above but as in foundation, footings, fdn beam, plinth beam & mass concrete.

same as above as in beam, cantilever, lintels over 1.5 mtr span.

M&L for TMT mild steel bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for TMT bars 6 mm to 8 mm dia and over cut to length, bent to shape reqd, including cranking and binding with and including MS wire annealed) not less than 0.9mm dia or securing with clips as in stirrups, spacers and binders. complete all as specified and directed

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping). Complete all as specified and directed.

M & L for formwork formwork to sides and soffits of floor or roof beams, beam haunch ings, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. Complete all as specified and directed.

All as per item No 23 but formwork as in sides of concrete foundation, footing, bases of column, plinth beams as for rough finished surfaces. Complete all as specified and directed.

All as per item No 23 here in before but formwork as in sides of Column, pillar, post. Complete all as specified and directed.

M&L White vitreous china laboratory sink of size 600x450x200mm including plugs, washers and wastes;including beding in cement mortar and connecting union to waste pipe CP waste coupling 32 mm dia ,and necessary fittings fixed complete all as specified and as directed.

S&F powder coated anodized aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc. complete all as specified including powder coating (minimum thickness of powder coating 50 micron), complete all as specified and directed

S&F for powder coated anodized aluminum window and ventilator shutter, side hung type without sash, aluminum sections weighing 0.55kg/m incl necessary jointing cleats, glazing clips, rubber packing, anodized aluminum snap beading, screws, anodized aluminum fittings such as peg stays 150mm long (1No) hinges type B-21 100mm long(2 No) suitable handle (1 No), complete all as specified and directed.

M&L for hard core of broken bricks of gauge n.exc 63 mm, deposited, spread and levelled in layers n.exc 7.5 CM thick water and rammed to a true surface. complete all as specified and directed.

M&L for Pressed steel frames of size 125mmx60mm made of 1.25mm thick Cold Rolled sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, complete all as specified.

M&L for PCC 1:3:6 type CO (using 12.5mm graded stone aggregate) as in hold fast iron fixing and back filing of pressed steel door frame including necessary form work all as specified.

S&F 30mm thick factory made Flush shutter solid core construction block board core and plywood face panel commercial type on both side complete all as specified.

S&F factory made 35mm thick 2nd class HW Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); supplied and fitted to chowkats Note: Glass/wire gauge shall be measured and paid for seperately.

S&F butt hinges, stainlees steel 100mm long (ISI marked), complete all as specified and directed

S&F Aluminum handles, 150 mm size plate type complete all as specified and directed.

S&F aluminium anodised, barrel tower bolt of extruded section and fixed, 200mm long (ISI marked), complete all as specified.

S& F in repair 300mm mild steel ordinary rat tail rod pattern springs including roller and rollar plate, fixed including welding/ fixing to steel/ wooden chowkats, complete all as specified and directed.

S&F aluminium alloy, 16mm dia and 250mm long anodised, sliding door bolt with hasp, staple (bolt type) with and fixing clips of sheet, cast or excluded sections and fixing bolts and sliding bolts of excluded sections or cast aluminum alloy and fixed, complete all as specified.

S&F Stainless Steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, wire staples or beading etc, complete all as specified and directed.

M&L for 12 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement as on wall complete all as specified and directed.

Material and labour for 15 mm thick rendering in cement mortar 1:4 mixed with approved water proofing compound on fair faces of brick surfaces or concrete surfaces, surface finished even and smooth without using extra cement all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces of roof projection/ ceiling etc surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of wall and applying two coats of oil emulsion distemper over 1.5 mm thick JK/Birla wall care putty to achieve smooth finish surface, complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.

Applying two coats of exterior acrylic emulsion (weather proof treatment ), in plain patterns, over new plastered surfaces , including preparation and using primer new surfaces ,complete all as specified and directed.

M&L for prepration of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

M&L for coloured vitrified double charged ceramic tiles 9 to 10 mm thick (square/rectangular) area of each tiles exceeding 0.36 Sqm but not exc 0.42 Sqm, in flooring etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

All per Serial item 50 here in before but tiles as in vertical surfaces and jointed in 10 mm thick in cement mortar 1:4.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade,with grey cement and pigment, incl 25 mm thick layer of fine sand. complete all as specified and as directed.

M&L for machine cut polished kota stone slab flooring of size of Kotastone 550 mm x 550 mm and 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, laid over and including 20mm thick screed bed in cement mortar 1:6, rubbing, grinding and polishing to achieve mirror finish, complete all as specified and directed. Note : Kota stone shall be laid in one piece for treads and risers for step, window cills and moulding/rounding of edge properly.

M&L for polished kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab, laid over and including 10mm thick rendering in cement mortar 1:4, rubbing, grinding, rounding of edges and polishing to achieve mirror finish, complete all as specified and directed. Note : Kota stone shall be laid in one piesce for treads and risers for step, window cills and moulding/rounding of edge properly.

M&L Granite 20 mm thick of any type work(table rubbed and polished) in steps, jambs,pillars windows cill, platform and like including pointing in white/colour cement and pigment to match with shade of granite including bull nosing of external. complete all as specified and as directed. complete all as specified and directed.

S&F 15mm bore Pillar taps cast copper alloy, with capstan head, fancy type, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and flynuts, screwed for iron pipe

S&F in repairs stop/angle valves, 15mm bore, fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, both ends screwed for iron pipe or for union etc., complete all as specified and directed.

S&F in repairs PVC connection 15mm dia, 450mm long, hot water grade with brass chromium plated nuts and washers at both ends, complete all as specified.

S&F 15mm Stop valve, fancy type, chromium plated with long shunk and cup (cocealed type) high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed

S&F PVC (SWR) pipes, 150mm dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors or walls, complete all as specified & directed.

S&F 150mm bore PVC (SWR) bends any radius, complete all as specified and directed.

S&F galvanized iron water tubing, ‘medium grade’ 15mm bore, with all fittings such as bend, tee, union etc., fixed complete to walls and ceilings or laid in floors, complete all as specified & directed.

S&F galvanized iron water tubing, ‘medium grade’ 20mm bore, with all fittings such as bend, tee, union etc., fixed complete to floor, walls and ceilings or laid in floors, complete all as specified & directed.

All as per Sr item No 60 here in before but GI pipe of 25 mm bore. complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single (Single T ) with access door equal or unequal, complete all as specified.

S&F Brass chromium plated bottle traps 40mm for sinks with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed.

M&L PVC (SWR) gully trap 125/110 mm,setting and jointing with solvent cement complete all as specified and as directed.

S&F Rotational moulded polythelene white water storage tank tripple layered white coloured, 500 litres capacity (cylinderical vertical with cxlosed top) hoisted with thread tank cover and fixed in position including GI tank nipple & with union(two nos each), including 20mm for ball valve brass high pressure, with polythene float and fly nut complete all as specified and directed.

M& L for 18mm thick solid HDHMR board with 0.9-1.20mm thick sunmica leminated sheet on both side of two different colours (colour finish) as in kitchen cabinet shutter, jointed to form cabinet by means of Adhesive Solvent and fixed using Self-tapping Aluminium Screws, including beddding, providing & fixing of Stainless steel piano hinges suitable for 18/19 mm HDHMR Board (minimum of 02 Nos for Each leaf ) to hold cabinet shutter , Stainless Steel Silver chrome Door Handle 100mm long (01 No for each leaf of shutter) and Door catcher (01 no for each leaf), complete all as specified and as directed. Note: (a) Quoted unit Rates are inclusive of PVC board,handles,hinges,screws,Door catcher and adhesive etc. (b) For the purpose of payment area of board alongwith decorative laminated sheet shall be measured.

M&L for PCC (1:2:4), nominal mix, type B-1, using 20mm graded crushed stone aggregate as in PCC padding on surfaces of roof finished even and fair without using extra cement, complete all as specified.

M&L for water proofing treatment with APP based modified 5 layered prefabricated water proofing polymeric memberane over roof consisting of cleaning of concrete or plastered surface of roof and applying evenly a bitumen primer conforming to IS 3488@ 0.30Kg per sqm followed by a tack coat @ 1.2kg per Sqm using 85/25 grade industrial hot blown bitumen over it laid with APP modified polymeric water proofing membrane minimum weighting 3.0 kg per Sqm reinforced with non-woven polyester fabric (weight not less than 170 gm per sqm) unrolled & bonded to substrate with longitudinal and end laps 100mm as per manufacturer's instruction and applying over it a tack coat using 85/25 grade industrial hot blown bitumen @ 1.2 kg sqm and as per manufacturer instruction and complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on roof surface using water proofing compund as per manufacturer instruction surfaces finished even and fair without using extra cement. complete all as specified and directed.

M&L for 40 mm thick brick tiles laid on and joints grouted flush in cement mortar 1:3 mixed with 5% crude oil by weight of cement on above treated surface complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B0 using 12.5mm graded aggregate as in sub floor , sub base; concrete surface finished even & rough to receive topping floor/tiles finish/layer complete all as specified.

Supply liquid water proofing compound (ISI marked), complete all as specified and directed.

M&L for point wiring with single core PVC insulated unsheathed 1100 volts grade FRLS cable of copper conductor multi stranded of size 1.5 sqmm (Nominal size) drawn through and including non metallic rigid PVC conduit medium grade, ISI marked not less then 20/25 mm dia with all accessories like tee, straight joint, L bend etc concealed in wall , ceiling , floor etc, pressed MS Sunken boxes in wall of required size and colour for switches and sockets, 1.5 sqmm (Nominal size) PVC insulated (green insulation) copper conductor FRLS earth continuity cable drawn with wiring and connected to common earth dolly all as specified for one light point/Ceiling fan/ Ehaust Fan and wall mount fan controlled by one SP switch including making good distrubed surface, complete all as specified and directed. Note :- Cost for MS Sunken Boxes, plates for modular switches, cutting, chieseling and cutting the wall/Ceiling for conduit fixing, making good to existing surfaces (Matching with existing colour) shall deemed to be included in the quoted rate.

All as per Srl item No 73 here-in-before but for one 5 pin socket out let, 6 Amps on same board with the cable 1.5 Sqmm size, complete all as specified and directed.

All as per Srl item No 73 here-in-before but for one power point 6 pin 15 Amps socket out let and Geyser Point for sheet metal enclosure with 2.5 Sq mm stranded copper conductor FRLS cable PVC insulated including earth wire 2.5 Sq mm copper conductor FRLS cable connected to earth dolly complete, all as specified and directed.

All as per item Sl No 73 here in with but for AC Point for sheet metal enclosure with 4 Sq mm stranded copper conductor FRLS cable PVC insulated including earth wire 4 Sq mm copper conductor FRLS cable connected to earth dolly complete, all as specified and directed.

S & F modular one module switch single pole one way 5 amp 240 volts, all as specified and as directed.

S & F Socket outlet two module, 2 in 1, 3 pin, 5 amps, 240 volts all as specified and as directed.

S & F modular switch single pole one module way 15 amp 240 volts, all as specified and as directed.

S & F modular Socket outlet 2 in 1, 3 pin, 5 and 15 amps, two module flush type, 240 volts all as specified and as directed.

S&F of ceiling rose, surface type, 65mm x 50mm, 3 terminal complete all as specified and as directed by Engr-in-Charge.

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceilingrose complete all as specified and directed by Engr-in-Charge.

S&F LED sleek mirror light fitting 10 watt provided with high output diffuser 2 feet, 230 Volts complete LED tube rod 10 watt with all accessories, pre wired and including connecting up with twin core copper conductor cable complete all as specified and directed by Engr-in-Charge.

S&F in replacement of LED building security light 30 watt, 230V with lens and toughen glass top.The luminarie should have a color temperature of 6500K, IP 65 complete PF > 0.95 with all accessories and including connecting up to ceiling rose with 0.5 sqmm three core copper flexible conductor cable, One GI medium grade 20/25 mm dia bracket of total length 50 cm and fixed to wall with 2 Nos MS Clamp and fastener all as specified and directed.

Supply and fix ing 40 mm bore steel water tubing light grade galvanised for cable protection. complete all as specified and directed.

S&F in replacement sheet metal enclosures single pole and neutral earth enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amps, 240 volts, complete all as specified and directed.

Supply and Fixing Sheet metal Vertical TPN double door DB 4 Way, 415 Volt, TPN with 200 Amps rated bus bar and with neutral, earthing bar and din rail complete all as specified and as directed by Engr-in-Charge

S&F of MCB SP, 6-32A,10KA, 'C' Curve complete all as specified and as directed .

S&F of MCB SPN, 40 to 63A ,10KA, 'C' Curve complete all as specified and as directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep, 350 RPM, Min air delivery 210 CMM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) and connecting up including provision of copper cable of size 1.5 sqmm from ceiling rose or connector to fan complete all as specified and directed.

S & F in MCB TPN four poles,100 Amps, breaking capacity 10 KA 'C' curve confirming to IS-8828, 415 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc. complete all as specified and as directed

Supply and laying LT UG XLPE insulated 1100 volt grade heavy duty cable, multi stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel strip wire or tape and connecting up to the electrical system with suitable size of aluminium lugs of size 35 sq mm 3.5 core complete all as specified and as directed.

Supply and fixing of gun metal gate valve with iron wheel head screwed both ends size 25 mm for iron/GI pipes complete all as specified and directed.

Supply and fixing of gun metal gate valve with iron wheel head screwed both ends size 20 mm for iron/GI pipes complete all as specified and directed.

M&L for Earthing complete for bldg with galvanised mild steel plate electrode, 60cm x 60cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, check nuts, washers of GI or steel, PCC (concrete chamber of size 300mm x 300mm x 300mm inside dimension) shall be PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate with fair finish, internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire gauge of 22 gauge, 8 mesh per liner inch, 80 mm thick PCC pit cover 320mm x 320mm of RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) reinforced with XPM JALLI and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) and specified including provision of earth wire protected by 15mm dia medium grade GI pipe and watering GI pipe shall be 20mm bore medium grade etc complete, all excavation and earth work & connecting the earthing to an earthing test point main switch board as specified and testing on completion complete all as specified & directed.

Contract Amount shall be derived after deducting the amount of Schedule of Credit in General Summary on serial page No of tender documents.

SRI SAI CONSTRUCTION COMPANY (BID ID -3372881)