NAGAR PANCHAYAT RABUPURA MAI TANKI PARISAR MAI AWASIYA BHAWAN KAI JIDODWAR KA AVSESH KARYA

E/W in excavation foundation in ordinary soil loam,clay or sand including lift upto 1.5 m. & lead upto 30m including filling watering & ramming of excavated earth into the trenches or in to th plinth removal & disposal of surplus earth as directed by the engineer in charge upto a distance of 30m from the foundation trenches. ( S.I No-251a)

Concrete with 40 mm gauge Brick ballast fine sand of 1.25 fineness modulous & Cement in proporation of 8:4:1 in foundation and under floor, includingsupply of all material labour and T&P etc. required for proper completition of the work.(S.I. No. 275)

M-150 class Brick work in 1:4 Cement & Fine sand of 1.25 F.M. mortor in foundation & plinth including supply of all materials, labour and T&P etc. Required for proper completion of the work. (S.I No.305)

12 mm thick plaster with cement and Coarse sand in 1:3 over brick work minimum thickness not be less then 1 cm including supply of all materials, labour , T & P etc. required for proper completion of the work as per S.I. No.583

E/W embankment cutting or inembankment inordinary soil,excavation to be in the form regular pits not exceeding 0.50M in depth and earth work in embankment to be in 20cm Layers including remming and dressing the surface to required level and slope and also including 1.5M lift and 10 km lead . The earth from cutting to be use in making embamkment or to be deposite as spoil banks with in 5 km distance as directed by the Engineer incharge.Including Royallity as S.I. No. 253(a)+261(b)

M.S or iron work of small sizes and section such as holding down bolts, hold fast, tie rods grating etc. wrought to required from including supply of steel bolts, nuts wastage etc. and their fixing required for proper completion of the work. S.i no-502

R.C.C. Work with cement, approved coarse sand & 2 CM gauge approved stone grit in proportions of 1:1.5:3 for slab excluding supply of reinforcement and its bending, but i/c its fixing and binding the same with 24 B.W.G.G.I. binding wire and i/c necessary centering and shuttering etc and supply of all materials, labour , T & P etc. required for proper completion of the work i/c cost of binding wire. The rate excludes making of drip course which shall be paid extra. S.I 5.17 NEW ITEM.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. DSR NO. 5.22.1

Cement concrete with 2 cm gauge stone grit, coarse sand & cement in the proportion of 4 :2:1 including supply of all materials, labour , T & P etc. required for proper completion of the work as per S.I. No. 279(a).

Supply and fixingof 6 to 8 mm thick ivory or light shades vitrefied tiles 600*600 mm size in flooring and skirting laid with 1:3 cement and Approved Coarse sand mortar finished with white cement slurry, jointing, and polishing complete, including supply of all materials, labour , T & P etc. required for proper completion of the work as per S.I. No.New item S.I 14.26

Supply and fixing 6 mm China white glaged tiles in flooring or in skirting or dado laid with 1:3 cement and Approved Coarse sand mortar finished with white cement slurry, jointing, and polishing complete, including supply of all materials, labour , T & P etc. required for proper completion of the work as per S.I. No.628

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. As per DSR 11.56.1 (Rate Factur =4481.3X0.735X111/107 = 0.76)

Providing wall putty on New surface with approvl quality material of Berjer J.K, Birla or similar make 02 coat including supply of all materials, labour , T & P etc. required for proper completion of the work as per S.I.N.O new item

Finishing wall with water proof cement paint(Weather coat) of approved make and quality on new work with three coat to give an even shade including supply of all materials, labour , T & P etc. required for proper completion of the work as per S.I.N.O. 660+661+662 new item

Supply and fixing of 10 cm internal dia P.V.C. down pipe Everest or charminar make complete with bends with at top and plain at bottom and grantings & supply of necessary M.S. clamp 2.5 cm × 30mm fixed to wall cement mortar 1:2 & i/c supply of 15 cm long 6 mm dia nail all materials, labour , T & P etc. required for proper completion of the work and also i/c repair of lplaster pointing etc. if damaged during fixed of the pipes. as per S.I.N.O. 730.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever requiredW.C. pan with ISI marked white solid plastic seat and lid DSR NO. 17.3.1

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. DSR NO. 17.31

Providing and fixing white vitreous china laboratory sink including making all connections excluding cost of fittings

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank DSR NO. 18.48

Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-PE Composite Pressure Pipes conforming to IS : 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer-in-charge. 1620 (20 mm OD) pipe DSR NO. 18.1.2

Providing and fixing bress bib cock of approved quality for 15 mm ominal bore as per DSR 18.15.1

Wiring point with 1.5 Sq mm pvc insulated Single core copper wire in PVC concealed conduit Light point 131 c

Fan point

Plug point 6Amp

S/F of 6 Amp to 32 Amp MCB.

celling fan

15Amp Power Plug

Supply and Fixixng of Tube light with batten suitable for upto 1x22 watt tube light.

S/Wiring of submain with P.V.C in Sulated copper in P.V.C cancealed conduet.(i) 2x2.5 Sq mm.